mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-13 14:04:05 +08:00
1a200a3966
The regmap API supports IO port accessors so we can take advantage of regmap abstractions rather than handling access to the device registers directly in the driver. For the PCIe-IDIO-24 series of devices, the following BARs are available: BAR[0]: memory mapped PEX8311 BAR[1]: I/O mapped PEX8311 BAR[2]: I/O mapped card registers There are 24 FET Output lines, 24 Isolated Input lines, and 8 TTL/CMOS lines (which may be configured for either output or input). The GPIO lines are exposed by the following card registers: Base +0x0-0x2 (Read/Write): FET Outputs Base +0xB (Read/Write): TTL/CMOS Base +0x4-0x6 (Read): Isolated Inputs Base +0x7 (Read): TTL/CMOS In order for the device to support interrupts, the PLX PEX8311 internal PCI wire interrupt and local interrupt input must first be enabled. The following card registers for Change-Of-State may be used: Base +0x8-0xA (Read): COS Status Inputs Base +0x8-0xA (Write): COS Clear Inputs Base +0xB (Read): COS Status TTL/CMOS Base +0xB (Write): COS Clear TTL/CMOS Base +0xE (Read/Write): COS Enable The COS Enable register is used to enable/disable interrupts and configure the interrupt levels; each bit maps to a group of eight inputs as described below: Bit 0: IRQ EN Rising Edge IN0-7 Bit 1: IRQ EN Rising Edge IN8-15 Bit 2: IRQ EN Rising Edge IN16-23 Bit 3: IRQ EN Rising Edge TTL0-7 Bit 4: IRQ EN Falling Edge IN0-7 Bit 5: IRQ EN Falling Edge IN8-15 Bit 6: IRQ EN Falling Edge IN16-23 Bit 7: IRQ EN Falling Edge TTL0-7 An interrupt is asserted when a change-of-state matching the interrupt level configuration respective for a particular group of eight inputs with enabled COS is detected. The COS Status registers may be read to determine which inputs have changed; if interrupts were enabled, an IRQ will be generated for the set bits in these registers. Writing the value read from the COS Status register back to the respective COS Clear register will clear just those interrupts. Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/3091e387b1d2eac011a1d84e493663aa2acf982e.1680708357.git.william.gray@linaro.org/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> |
||
---|---|---|
.. | ||
accel | ||
accessibility | ||
acpi | ||
amba | ||
android | ||
ata | ||
atm | ||
auxdisplay | ||
base | ||
bcma | ||
block | ||
bluetooth | ||
bus | ||
cdrom | ||
cdx | ||
char | ||
clk | ||
clocksource | ||
comedi | ||
connector | ||
counter | ||
cpufreq | ||
cpuidle | ||
crypto | ||
cxl | ||
dax | ||
dca | ||
devfreq | ||
dio | ||
dma | ||
dma-buf | ||
edac | ||
eisa | ||
extcon | ||
firewire | ||
firmware | ||
fpga | ||
fsi | ||
gnss | ||
gpio | ||
gpu | ||
greybus | ||
hid | ||
hsi | ||
hte | ||
hv | ||
hwmon | ||
hwspinlock | ||
hwtracing | ||
i2c | ||
i3c | ||
idle | ||
iio | ||
infiniband | ||
input | ||
interconnect | ||
iommu | ||
ipack | ||
irqchip | ||
isdn | ||
leds | ||
macintosh | ||
mailbox | ||
mcb | ||
md | ||
media | ||
memory | ||
memstick | ||
message | ||
mfd | ||
misc | ||
mmc | ||
most | ||
mtd | ||
mux | ||
net | ||
nfc | ||
ntb | ||
nubus | ||
nvdimm | ||
nvme | ||
nvmem | ||
of | ||
opp | ||
parisc | ||
parport | ||
pci | ||
pcmcia | ||
peci | ||
perf | ||
phy | ||
pinctrl | ||
platform | ||
pnp | ||
power | ||
powercap | ||
pps | ||
ps3 | ||
ptp | ||
pwm | ||
rapidio | ||
ras | ||
regulator | ||
remoteproc | ||
reset | ||
rpmsg | ||
rtc | ||
s390 | ||
sbus | ||
scsi | ||
sh | ||
siox | ||
slimbus | ||
soc | ||
soundwire | ||
spi | ||
spmi | ||
ssb | ||
staging | ||
target | ||
tc | ||
tee | ||
thermal | ||
thunderbolt | ||
tty | ||
ufs | ||
uio | ||
usb | ||
vdpa | ||
vfio | ||
vhost | ||
video | ||
virt | ||
virtio | ||
vlynq | ||
w1 | ||
watchdog | ||
xen | ||
zorro | ||
Kconfig | ||
Makefile |