mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-15 16:24:13 +08:00
9bcf15f75c
Prior to this commit there were 3 issues with our handling of the TS-pin:
1) There are 2 ways how the firmware can disable monitoring of the TS-pin
for designs which do not have a temperature-sensor for the battery:
a) Clearing bit 0 of the AXP20X_ADC_EN1 register
b) Setting bit 2 of the AXP288_ADC_TS_PIN_CTRL monitoring
Prior to this commit we were unconditionally setting both bits to the
value used on devices with a TS. This causes the temperature protection to
kick in on devices without a TS, such as the Jumper ezbook v2, causing
them to not charge under Linux.
This commit fixes this by using regmap_update_bits when updating these 2
registers, leaving the 2 mentioned bits alone.
The next 2 problems are related to our handling of the current-source
for the TS-pin. The current-source used for the battery temp-sensor (TS)
is shared with the GPADC. For proper fuel-gauge and charger operation the
TS current-source needs to be permanently on. But to read the GPADC we
need to temporary switch the TS current-source to ondemand, so that the
GPADC can use it, otherwise we will always read an all 0 value.
2) Problem 2 is we were writing hardcoded values to the ADC TS pin-ctrl
register, overwriting various other unrelated bits. Specifically we were
overwriting the current-source setting for the TS and GPIO0 pins, forcing
it to 80ųA independent of its original setting. On a Chuwi Vi10 tablet
this was causing us to get a too high adc value (due to a too high
current-source) resulting in the following errors being logged:
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.SXP1._TMP, AE_ERROR
This commit fixes this by using regmap_update_bits to change only the
relevant bits.
3) After reading the GPADC channel we were unconditionally enabling the
TS current-source even on devices where the TS-pin is not used and the
current-source thus was off before axp288_adc_read_raw call.
This commit fixes this by making axp288_adc_set_ts a nop on devices where
the ADC is not enabled for the TS-pin.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1610545
Fixes: 3091141d78
("iio: adc: axp288: Fix the GPADC pin ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
307 lines
8.0 KiB
C
307 lines
8.0 KiB
C
/*
|
|
* axp288_adc.c - X-Powers AXP288 PMIC ADC Driver
|
|
*
|
|
* Copyright (C) 2014 Intel Corporation
|
|
*
|
|
* ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; version 2 of the License.
|
|
*
|
|
* This program is distributed in the hope that it will be useful, but
|
|
* WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
|
|
* General Public License for more details.
|
|
*
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/device.h>
|
|
#include <linux/regmap.h>
|
|
#include <linux/mfd/axp20x.h>
|
|
#include <linux/platform_device.h>
|
|
|
|
#include <linux/iio/iio.h>
|
|
#include <linux/iio/machine.h>
|
|
#include <linux/iio/driver.h>
|
|
|
|
/*
|
|
* This mask enables all ADCs except for the battery temp-sensor (TS), that is
|
|
* left as-is to avoid breaking charging on devices without a temp-sensor.
|
|
*/
|
|
#define AXP288_ADC_EN_MASK 0xF0
|
|
#define AXP288_ADC_TS_ENABLE 0x01
|
|
|
|
#define AXP288_ADC_TS_CURRENT_ON_OFF_MASK GENMASK(1, 0)
|
|
#define AXP288_ADC_TS_CURRENT_OFF (0 << 0)
|
|
#define AXP288_ADC_TS_CURRENT_ON_WHEN_CHARGING (1 << 0)
|
|
#define AXP288_ADC_TS_CURRENT_ON_ONDEMAND (2 << 0)
|
|
#define AXP288_ADC_TS_CURRENT_ON (3 << 0)
|
|
|
|
enum axp288_adc_id {
|
|
AXP288_ADC_TS,
|
|
AXP288_ADC_PMIC,
|
|
AXP288_ADC_GP,
|
|
AXP288_ADC_BATT_CHRG_I,
|
|
AXP288_ADC_BATT_DISCHRG_I,
|
|
AXP288_ADC_BATT_V,
|
|
AXP288_ADC_NR_CHAN,
|
|
};
|
|
|
|
struct axp288_adc_info {
|
|
int irq;
|
|
struct regmap *regmap;
|
|
bool ts_enabled;
|
|
};
|
|
|
|
static const struct iio_chan_spec axp288_adc_channels[] = {
|
|
{
|
|
.indexed = 1,
|
|
.type = IIO_TEMP,
|
|
.channel = 0,
|
|
.address = AXP288_TS_ADC_H,
|
|
.datasheet_name = "TS_PIN",
|
|
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
|
|
}, {
|
|
.indexed = 1,
|
|
.type = IIO_TEMP,
|
|
.channel = 1,
|
|
.address = AXP288_PMIC_ADC_H,
|
|
.datasheet_name = "PMIC_TEMP",
|
|
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
|
|
}, {
|
|
.indexed = 1,
|
|
.type = IIO_TEMP,
|
|
.channel = 2,
|
|
.address = AXP288_GP_ADC_H,
|
|
.datasheet_name = "GPADC",
|
|
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
|
|
}, {
|
|
.indexed = 1,
|
|
.type = IIO_CURRENT,
|
|
.channel = 3,
|
|
.address = AXP20X_BATT_CHRG_I_H,
|
|
.datasheet_name = "BATT_CHG_I",
|
|
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
|
|
}, {
|
|
.indexed = 1,
|
|
.type = IIO_CURRENT,
|
|
.channel = 4,
|
|
.address = AXP20X_BATT_DISCHRG_I_H,
|
|
.datasheet_name = "BATT_DISCHRG_I",
|
|
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
|
|
}, {
|
|
.indexed = 1,
|
|
.type = IIO_VOLTAGE,
|
|
.channel = 5,
|
|
.address = AXP20X_BATT_V_H,
|
|
.datasheet_name = "BATT_V",
|
|
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
|
|
},
|
|
};
|
|
|
|
/* for consumer drivers */
|
|
static struct iio_map axp288_adc_default_maps[] = {
|
|
IIO_MAP("TS_PIN", "axp288-batt", "axp288-batt-temp"),
|
|
IIO_MAP("PMIC_TEMP", "axp288-pmic", "axp288-pmic-temp"),
|
|
IIO_MAP("GPADC", "axp288-gpadc", "axp288-system-temp"),
|
|
IIO_MAP("BATT_CHG_I", "axp288-chrg", "axp288-chrg-curr"),
|
|
IIO_MAP("BATT_DISCHRG_I", "axp288-chrg", "axp288-chrg-d-curr"),
|
|
IIO_MAP("BATT_V", "axp288-batt", "axp288-batt-volt"),
|
|
{},
|
|
};
|
|
|
|
static int axp288_adc_read_channel(int *val, unsigned long address,
|
|
struct regmap *regmap)
|
|
{
|
|
u8 buf[2];
|
|
|
|
if (regmap_bulk_read(regmap, address, buf, 2))
|
|
return -EIO;
|
|
*val = (buf[0] << 4) + ((buf[1] >> 4) & 0x0F);
|
|
|
|
return IIO_VAL_INT;
|
|
}
|
|
|
|
/*
|
|
* The current-source used for the battery temp-sensor (TS) is shared
|
|
* with the GPADC. For proper fuel-gauge and charger operation the TS
|
|
* current-source needs to be permanently on. But to read the GPADC we
|
|
* need to temporary switch the TS current-source to ondemand, so that
|
|
* the GPADC can use it, otherwise we will always read an all 0 value.
|
|
*/
|
|
static int axp288_adc_set_ts(struct axp288_adc_info *info,
|
|
unsigned int mode, unsigned long address)
|
|
{
|
|
int ret;
|
|
|
|
/* No need to switch the current-source if the TS pin is disabled */
|
|
if (!info->ts_enabled)
|
|
return 0;
|
|
|
|
/* Channels other than GPADC do not need the current source */
|
|
if (address != AXP288_GP_ADC_H)
|
|
return 0;
|
|
|
|
ret = regmap_update_bits(info->regmap, AXP288_ADC_TS_PIN_CTRL,
|
|
AXP288_ADC_TS_CURRENT_ON_OFF_MASK, mode);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* When switching to the GPADC pin give things some time to settle */
|
|
if (mode == AXP288_ADC_TS_CURRENT_ON_ONDEMAND)
|
|
usleep_range(6000, 10000);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int axp288_adc_read_raw(struct iio_dev *indio_dev,
|
|
struct iio_chan_spec const *chan,
|
|
int *val, int *val2, long mask)
|
|
{
|
|
int ret;
|
|
struct axp288_adc_info *info = iio_priv(indio_dev);
|
|
|
|
mutex_lock(&indio_dev->mlock);
|
|
switch (mask) {
|
|
case IIO_CHAN_INFO_RAW:
|
|
if (axp288_adc_set_ts(info, AXP288_ADC_TS_CURRENT_ON_ONDEMAND,
|
|
chan->address)) {
|
|
dev_err(&indio_dev->dev, "GPADC mode\n");
|
|
ret = -EINVAL;
|
|
break;
|
|
}
|
|
ret = axp288_adc_read_channel(val, chan->address, info->regmap);
|
|
if (axp288_adc_set_ts(info, AXP288_ADC_TS_CURRENT_ON,
|
|
chan->address))
|
|
dev_err(&indio_dev->dev, "TS pin restore\n");
|
|
break;
|
|
default:
|
|
ret = -EINVAL;
|
|
}
|
|
mutex_unlock(&indio_dev->mlock);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int axp288_adc_initialize(struct axp288_adc_info *info)
|
|
{
|
|
int ret, adc_enable_val;
|
|
|
|
/*
|
|
* Determine if the TS pin is enabled and set the TS current-source
|
|
* accordingly.
|
|
*/
|
|
ret = regmap_read(info->regmap, AXP20X_ADC_EN1, &adc_enable_val);
|
|
if (ret)
|
|
return ret;
|
|
|
|
if (adc_enable_val & AXP288_ADC_TS_ENABLE) {
|
|
info->ts_enabled = true;
|
|
ret = regmap_update_bits(info->regmap, AXP288_ADC_TS_PIN_CTRL,
|
|
AXP288_ADC_TS_CURRENT_ON_OFF_MASK,
|
|
AXP288_ADC_TS_CURRENT_ON);
|
|
} else {
|
|
info->ts_enabled = false;
|
|
ret = regmap_update_bits(info->regmap, AXP288_ADC_TS_PIN_CTRL,
|
|
AXP288_ADC_TS_CURRENT_ON_OFF_MASK,
|
|
AXP288_ADC_TS_CURRENT_OFF);
|
|
}
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* Turn on the ADC for all channels except TS, leave TS as is */
|
|
return regmap_update_bits(info->regmap, AXP20X_ADC_EN1,
|
|
AXP288_ADC_EN_MASK, AXP288_ADC_EN_MASK);
|
|
}
|
|
|
|
static const struct iio_info axp288_adc_iio_info = {
|
|
.read_raw = &axp288_adc_read_raw,
|
|
};
|
|
|
|
static int axp288_adc_probe(struct platform_device *pdev)
|
|
{
|
|
int ret;
|
|
struct axp288_adc_info *info;
|
|
struct iio_dev *indio_dev;
|
|
struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
|
|
|
|
indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*info));
|
|
if (!indio_dev)
|
|
return -ENOMEM;
|
|
|
|
info = iio_priv(indio_dev);
|
|
info->irq = platform_get_irq(pdev, 0);
|
|
if (info->irq < 0) {
|
|
dev_err(&pdev->dev, "no irq resource?\n");
|
|
return info->irq;
|
|
}
|
|
platform_set_drvdata(pdev, indio_dev);
|
|
info->regmap = axp20x->regmap;
|
|
/*
|
|
* Set ADC to enabled state at all time, including system suspend.
|
|
* otherwise internal fuel gauge functionality may be affected.
|
|
*/
|
|
ret = axp288_adc_initialize(info);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "unable to enable ADC device\n");
|
|
return ret;
|
|
}
|
|
|
|
indio_dev->dev.parent = &pdev->dev;
|
|
indio_dev->name = pdev->name;
|
|
indio_dev->channels = axp288_adc_channels;
|
|
indio_dev->num_channels = ARRAY_SIZE(axp288_adc_channels);
|
|
indio_dev->info = &axp288_adc_iio_info;
|
|
indio_dev->modes = INDIO_DIRECT_MODE;
|
|
ret = iio_map_array_register(indio_dev, axp288_adc_default_maps);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ret = iio_device_register(indio_dev);
|
|
if (ret < 0) {
|
|
dev_err(&pdev->dev, "unable to register iio device\n");
|
|
goto err_array_unregister;
|
|
}
|
|
return 0;
|
|
|
|
err_array_unregister:
|
|
iio_map_array_unregister(indio_dev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int axp288_adc_remove(struct platform_device *pdev)
|
|
{
|
|
struct iio_dev *indio_dev = platform_get_drvdata(pdev);
|
|
|
|
iio_device_unregister(indio_dev);
|
|
iio_map_array_unregister(indio_dev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct platform_device_id axp288_adc_id_table[] = {
|
|
{ .name = "axp288_adc" },
|
|
{},
|
|
};
|
|
|
|
static struct platform_driver axp288_adc_driver = {
|
|
.probe = axp288_adc_probe,
|
|
.remove = axp288_adc_remove,
|
|
.id_table = axp288_adc_id_table,
|
|
.driver = {
|
|
.name = "axp288_adc",
|
|
},
|
|
};
|
|
|
|
MODULE_DEVICE_TABLE(platform, axp288_adc_id_table);
|
|
|
|
module_platform_driver(axp288_adc_driver);
|
|
|
|
MODULE_AUTHOR("Jacob Pan <jacob.jun.pan@linux.intel.com>");
|
|
MODULE_DESCRIPTION("X-Powers AXP288 ADC Driver");
|
|
MODULE_LICENSE("GPL");
|