mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-19 10:14:23 +08:00
6ec4bedbf1
The Freescale PowerPC RapidIO controller consists of a RapidIO endpoint and a RapidIO message unit(RMU). Or use RapidIO message manager(RMan) to replace the RMU in DPAA architecture. Therefore, we should split the code into two function modules according to the hardware architecture. Add new struct for RMU module, and new initialization function to set up RMU module. This policy is very conducive to adding new module like RMan, or adding multi-ports or message units support. Signed-off-by: Lian Minghuan <Minghuan.Lian@freescale.com> Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Acked-by: Alexandre Bounine <alexandre.bounine@idt.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
67 lines
2.2 KiB
Makefile
67 lines
2.2 KiB
Makefile
subdir-ccflags-$(CONFIG_PPC_WERROR) := -Werror
|
|
|
|
ccflags-$(CONFIG_PPC64) := -mno-minimal-toc
|
|
|
|
mpic-msi-obj-$(CONFIG_PCI_MSI) += mpic_msi.o mpic_u3msi.o mpic_pasemi_msi.o
|
|
obj-$(CONFIG_MPIC) += mpic.o $(mpic-msi-obj-y)
|
|
obj-$(CONFIG_PPC_EPAPR_HV_PIC) += ehv_pic.o
|
|
fsl-msi-obj-$(CONFIG_PCI_MSI) += fsl_msi.o
|
|
obj-$(CONFIG_PPC_MSI_BITMAP) += msi_bitmap.o
|
|
|
|
obj-$(CONFIG_PPC_MPC106) += grackle.o
|
|
obj-$(CONFIG_PPC_DCR_NATIVE) += dcr-low.o
|
|
obj-$(CONFIG_PPC_PMI) += pmi.o
|
|
obj-$(CONFIG_U3_DART) += dart_iommu.o
|
|
obj-$(CONFIG_MMIO_NVRAM) += mmio_nvram.o
|
|
obj-$(CONFIG_FSL_SOC) += fsl_soc.o
|
|
obj-$(CONFIG_FSL_PCI) += fsl_pci.o $(fsl-msi-obj-y)
|
|
obj-$(CONFIG_FSL_PMC) += fsl_pmc.o
|
|
obj-$(CONFIG_FSL_LBC) += fsl_lbc.o
|
|
obj-$(CONFIG_FSL_GTM) += fsl_gtm.o
|
|
obj-$(CONFIG_FSL_85XX_CACHE_SRAM) += fsl_85xx_l2ctlr.o fsl_85xx_cache_sram.o
|
|
obj-$(CONFIG_SIMPLE_GPIO) += simple_gpio.o
|
|
obj-$(CONFIG_FSL_RIO) += fsl_rio.o fsl_rmu.o
|
|
obj-$(CONFIG_TSI108_BRIDGE) += tsi108_pci.o tsi108_dev.o
|
|
obj-$(CONFIG_QUICC_ENGINE) += qe_lib/
|
|
obj-$(CONFIG_PPC_BESTCOMM) += bestcomm/
|
|
mv64x60-$(CONFIG_PCI) += mv64x60_pci.o
|
|
obj-$(CONFIG_MV64X60) += $(mv64x60-y) mv64x60_pic.o mv64x60_dev.o \
|
|
mv64x60_udbg.o
|
|
obj-$(CONFIG_RTC_DRV_CMOS) += rtc_cmos_setup.o
|
|
obj-$(CONFIG_AXON_RAM) += axonram.o
|
|
|
|
obj-$(CONFIG_PPC_INDIRECT_PCI) += indirect_pci.o
|
|
obj-$(CONFIG_PPC_I8259) += i8259.o
|
|
obj-$(CONFIG_IPIC) += ipic.o
|
|
obj-$(CONFIG_4xx) += uic.o
|
|
obj-$(CONFIG_4xx_SOC) += ppc4xx_soc.o
|
|
obj-$(CONFIG_XILINX_VIRTEX) += xilinx_intc.o
|
|
obj-$(CONFIG_XILINX_PCI) += xilinx_pci.o
|
|
obj-$(CONFIG_OF_RTC) += of_rtc.o
|
|
ifeq ($(CONFIG_PCI),y)
|
|
obj-$(CONFIG_4xx) += ppc4xx_pci.o
|
|
endif
|
|
obj-$(CONFIG_PPC4xx_MSI) += ppc4xx_msi.o
|
|
obj-$(CONFIG_PPC4xx_CPM) += ppc4xx_cpm.o
|
|
obj-$(CONFIG_PPC4xx_GPIO) += ppc4xx_gpio.o
|
|
|
|
obj-$(CONFIG_CPM) += cpm_common.o
|
|
obj-$(CONFIG_CPM2) += cpm2.o cpm2_pic.o
|
|
obj-$(CONFIG_QUICC_ENGINE) += cpm_common.o
|
|
obj-$(CONFIG_PPC_DCR) += dcr.o
|
|
obj-$(CONFIG_8xx) += mpc8xx_pic.o cpm1.o
|
|
obj-$(CONFIG_UCODE_PATCH) += micropatch.o
|
|
|
|
obj-$(CONFIG_PPC_MPC512x) += mpc5xxx_clocks.o
|
|
obj-$(CONFIG_PPC_MPC52xx) += mpc5xxx_clocks.o
|
|
|
|
ifeq ($(CONFIG_SUSPEND),y)
|
|
obj-$(CONFIG_6xx) += 6xx-suspend.o
|
|
endif
|
|
|
|
obj-$(CONFIG_PPC_SCOM) += scom.o
|
|
|
|
subdir-ccflags-$(CONFIG_PPC_WERROR) := -Werror
|
|
|
|
obj-$(CONFIG_PPC_XICS) += xics/
|