mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-15 15:04:27 +08:00
4da722ca19
Pretty much any node can have a status property, so it doesn't need to be in examples. Converted with the following command and removed examples with SoC and board specific splits: git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d' Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rob Herring <robh@kernel.org>
77 lines
2.9 KiB
Plaintext
77 lines
2.9 KiB
Plaintext
* APM X-Gene 15Gbps Multi-purpose PHY nodes
|
|
|
|
PHY nodes are defined to describe on-chip 15Gbps Multi-purpose PHY. Each
|
|
PHY (pair of lanes) has its own node.
|
|
|
|
Required properties:
|
|
- compatible : Shall be "apm,xgene-phy".
|
|
- reg : PHY memory resource is the SDS PHY access resource.
|
|
- #phy-cells : Shall be 1 as it expects one argument for setting
|
|
the mode of the PHY. Possible values are 0 (SATA),
|
|
1 (SGMII), 2 (PCIe), 3 (USB), and 4 (XFI).
|
|
|
|
Optional properties:
|
|
- status : Shall be "ok" if enabled or "disabled" if disabled.
|
|
Default is "ok".
|
|
- clocks : Reference to the clock entry.
|
|
- apm,tx-eye-tuning : Manual control to fine tune the capture of the serial
|
|
bit lines from the automatic calibrated position.
|
|
Two set of 3-tuple setting for each (up to 3)
|
|
supported link speed on the host. Range from 0 to
|
|
127 in unit of one bit period. Default is 10.
|
|
- apm,tx-eye-direction : Eye tuning manual control direction. 0 means sample
|
|
data earlier than the nominal sampling point. 1 means
|
|
sample data later than the nominal sampling point.
|
|
Two set of 3-tuple setting for each (up to 3)
|
|
supported link speed on the host. Default is 0.
|
|
- apm,tx-boost-gain : Frequency boost AC (LSB 3-bit) and DC (2-bit)
|
|
gain control. Two set of 3-tuple setting for each
|
|
(up to 3) supported link speed on the host. Range is
|
|
between 0 to 31 in unit of dB. Default is 3.
|
|
- apm,tx-amplitude : Amplitude control. Two set of 3-tuple setting for
|
|
each (up to 3) supported link speed on the host.
|
|
Range is between 0 to 199500 in unit of uV.
|
|
Default is 199500 uV.
|
|
- apm,tx-pre-cursor1 : 1st pre-cursor emphasis taps control. Two set of
|
|
3-tuple setting for each (up to 3) supported link
|
|
speed on the host. Range is 0 to 273000 in unit of
|
|
uV. Default is 0.
|
|
- apm,tx-pre-cursor2 : 2st pre-cursor emphasis taps control. Two set of
|
|
3-tuple setting for each (up to 3) supported link
|
|
speed on the host. Range is 0 to 127400 in unit uV.
|
|
Default is 0x0.
|
|
- apm,tx-post-cursor : Post-cursor emphasis taps control. Two set of
|
|
3-tuple setting for Gen1, Gen2, and Gen3. Range is
|
|
between 0 to 0x1f in unit of 18.2mV. Default is 0xf.
|
|
- apm,tx-speed : Tx operating speed. One set of 3-tuple for each
|
|
supported link speed on the host.
|
|
0 = 1-2Gbps
|
|
1 = 2-4Gbps (1st tuple default)
|
|
2 = 4-8Gbps
|
|
3 = 8-15Gbps (2nd tuple default)
|
|
4 = 2.5-4Gbps
|
|
5 = 4-5Gbps
|
|
6 = 5-6Gbps
|
|
7 = 6-16Gbps (3rd tuple default)
|
|
|
|
NOTE: PHY override parameters are board specific setting.
|
|
|
|
Example:
|
|
phy1: phy@1f21a000 {
|
|
compatible = "apm,xgene-phy";
|
|
reg = <0x0 0x1f21a000 0x0 0x100>;
|
|
#phy-cells = <1>;
|
|
};
|
|
|
|
phy2: phy@1f22a000 {
|
|
compatible = "apm,xgene-phy";
|
|
reg = <0x0 0x1f22a000 0x0 0x100>;
|
|
#phy-cells = <1>;
|
|
};
|
|
|
|
phy3: phy@1f23a000 {
|
|
compatible = "apm,xgene-phy";
|
|
reg = <0x0 0x1f23a000 0x0 0x100>;
|
|
#phy-cells = <1>;
|
|
};
|