korg/linux
0
0
Fork 0
mirror of https://mirrors.bfsu.edu.cn/git/linux.git synced 2024-11-17 17:24:17 +08:00
Code Issues Packages Projects Releases Wiki Activity
057d1c0d1b
linux/drivers/scsi/pm8001/pm80xx_hwi.c
Deepak Ukey dba2cc03b9 scsi: pm80xx: sysfs attribute for non fatal dump 
Added the sysfs attribute for non fatal log so that management utility can
get the non fatal dump from driver. The non-fatal error is an error
condition or abnormal behavior detected by the host, or detected and
reported by the controller to the host.The non-fatal error does not stop
the controller firmware and enables it to still respond to host requests.
A typical example of a non-fatal error is an I/O timeout or an unusual
error notification from the controller. Since the firmware is operational,
the error dump information is pushed to host memory (by firmware) upon
request from the host.

Link: https://lore.kernel.org/r/20200316074906.9119-6-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-03-17 13:57:18 -04:00

5117 lines
164 KiB
C
Raw Blame History

/*
* PMC-Sierra SPCv/ve 8088/8089 SAS/SATA based host adapters driver
*
* Copyright (c) 2008-2009 PMC-Sierra, Inc.,
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* substantially similar to the "NO WARRANTY" disclaimer below
* ("Disclaimer") and any redistribution must be conditioned upon
* including a substantially similar Disclaimer requirement for further
* binary redistribution.
* 3. Neither the names of the above-listed copyright holders nor the names
* of any contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2 as published by the Free
* Software Foundation.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGES.
*
*/
#include <linux/slab.h>
#include "pm8001_sas.h"
#include "pm80xx_hwi.h"
#include "pm8001_chips.h"
#include "pm8001_ctl.h"
#define SMP_DIRECT 1
#define SMP_INDIRECT 2
int pm80xx_bar4_shift(struct pm8001_hba_info *pm8001_ha, u32 shift_value)
{
u32 reg_val;
unsigned long start;
pm8001_cw32(pm8001_ha, 0, MEMBASE_II_SHIFT_REGISTER, shift_value);
/* confirm the setting is written */
start = jiffies + HZ; /* 1 sec */
do {
reg_val = pm8001_cr32(pm8001_ha, 0, MEMBASE_II_SHIFT_REGISTER);
} while ((reg_val != shift_value) && time_before(jiffies, start));
if (reg_val != shift_value) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("TIMEOUT:MEMBASE_II_SHIFT_REGISTER"
" = 0x%x\n", reg_val));
return -1;
}
return 0;
}
void pm80xx_pci_mem_copy(struct pm8001_hba_info *pm8001_ha, u32 soffset,
const void *destination,
u32 dw_count, u32 bus_base_number)
{
u32 index, value, offset;
u32 *destination1;
destination1 = (u32 *)destination;
for (index = 0; index < dw_count; index += 4, destination1++) {
offset = (soffset + index);
if (offset < (64 * 1024)) {
value = pm8001_cr32(pm8001_ha, bus_base_number, offset);
*destination1 = cpu_to_le32(value);
}
}
return;
}
ssize_t pm80xx_get_fatal_dump(struct device *cdev,
struct device_attribute *attr, char *buf)
{
struct Scsi_Host *shost = class_to_shost(cdev);
struct sas_ha_struct *sha = SHOST_TO_SAS_HA(shost);
struct pm8001_hba_info *pm8001_ha = sha->lldd_ha;
void __iomem *fatal_table_address = pm8001_ha->fatal_tbl_addr;
u32 accum_len , reg_val, index, *temp;
u32 status = 1;
unsigned long start;
u8 *direct_data;
char *fatal_error_data = buf;
u32 length_to_read;
u32 offset;
pm8001_ha->forensic_info.data_buf.direct_data = buf;
if (pm8001_ha->chip_id == chip_8001) {
pm8001_ha->forensic_info.data_buf.direct_data +=
sprintf(pm8001_ha->forensic_info.data_buf.direct_data,
"Not supported for SPC controller");
return (char *)pm8001_ha->forensic_info.data_buf.direct_data -
(char *)buf;
}
/* initialize variables for very first call from host application */
if (pm8001_ha->forensic_info.data_buf.direct_offset == 0) {
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("forensic_info TYPE_NON_FATAL..............\n"));
direct_data = (u8 *)fatal_error_data;
pm8001_ha->forensic_info.data_type = TYPE_NON_FATAL;
pm8001_ha->forensic_info.data_buf.direct_len = SYSFS_OFFSET;
pm8001_ha->forensic_info.data_buf.direct_offset = 0;
pm8001_ha->forensic_info.data_buf.read_len = 0;
pm8001_ha->forensic_preserved_accumulated_transfer = 0;
/* Write signature to fatal dump table */
pm8001_mw32(fatal_table_address,
MPI_FATAL_EDUMP_TABLE_SIGNATURE, 0x1234abcd);
pm8001_ha->forensic_info.data_buf.direct_data = direct_data;
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("ossaHwCB: status1 %d\n", status));
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("ossaHwCB: read_len 0x%x\n",
pm8001_ha->forensic_info.data_buf.read_len));
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("ossaHwCB: direct_len 0x%x\n",
pm8001_ha->forensic_info.data_buf.direct_len));
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("ossaHwCB: direct_offset 0x%x\n",
pm8001_ha->forensic_info.data_buf.direct_offset));
}
if (pm8001_ha->forensic_info.data_buf.direct_offset == 0) {
/* start to get data */
/* Program the MEMBASE II Shifting Register with 0x00.*/
pm8001_cw32(pm8001_ha, 0, MEMBASE_II_SHIFT_REGISTER,
pm8001_ha->fatal_forensic_shift_offset);
pm8001_ha->forensic_last_offset = 0;
pm8001_ha->forensic_fatal_step = 0;
pm8001_ha->fatal_bar_loc = 0;
}
/* Read until accum_len is retrived */
accum_len = pm8001_mr32(fatal_table_address,
MPI_FATAL_EDUMP_TABLE_ACCUM_LEN);
/* Determine length of data between previously stored transfer length
* and current accumulated transfer length
*/
length_to_read =
accum_len - pm8001_ha->forensic_preserved_accumulated_transfer;
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("get_fatal_spcv: accum_len 0x%x\n", accum_len));
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("get_fatal_spcv: length_to_read 0x%x\n",
length_to_read));
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("get_fatal_spcv: last_offset 0x%x\n",
pm8001_ha->forensic_last_offset));
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("get_fatal_spcv: read_len 0x%x\n",
pm8001_ha->forensic_info.data_buf.read_len));
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("get_fatal_spcv:: direct_len 0x%x\n",
pm8001_ha->forensic_info.data_buf.direct_len));
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("get_fatal_spcv:: direct_offset 0x%x\n",
pm8001_ha->forensic_info.data_buf.direct_offset));
/* If accumulated length failed to read correctly fail the attempt.*/
if (accum_len == 0xFFFFFFFF) {
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("Possible PCI issue 0x%x not expected\n",
accum_len));
return status;
}
/* If accumulated length is zero fail the attempt */
if (accum_len == 0) {
pm8001_ha->forensic_info.data_buf.direct_data +=
sprintf(pm8001_ha->forensic_info.data_buf.direct_data,
"%08x ", 0xFFFFFFFF);
return (char *)pm8001_ha->forensic_info.data_buf.direct_data -
(char *)buf;
}
/* Accumulated length is good so start capturing the first data */
temp = (u32 *)pm8001_ha->memoryMap.region[FORENSIC_MEM].virt_ptr;
if (pm8001_ha->forensic_fatal_step == 0) {
moreData:
/* If data to read is less than SYSFS_OFFSET then reduce the
* length of dataLen
*/
if (pm8001_ha->forensic_last_offset + SYSFS_OFFSET
> length_to_read) {
pm8001_ha->forensic_info.data_buf.direct_len =
length_to_read -
pm8001_ha->forensic_last_offset;
} else {
pm8001_ha->forensic_info.data_buf.direct_len =
SYSFS_OFFSET;
}
if (pm8001_ha->forensic_info.data_buf.direct_data) {
/* Data is in bar, copy to host memory */
pm80xx_pci_mem_copy(pm8001_ha,
pm8001_ha->fatal_bar_loc,
pm8001_ha->memoryMap.region[FORENSIC_MEM].virt_ptr,
pm8001_ha->forensic_info.data_buf.direct_len, 1);
}
pm8001_ha->fatal_bar_loc +=
pm8001_ha->forensic_info.data_buf.direct_len;
pm8001_ha->forensic_info.data_buf.direct_offset +=
pm8001_ha->forensic_info.data_buf.direct_len;
pm8001_ha->forensic_last_offset +=
pm8001_ha->forensic_info.data_buf.direct_len;
pm8001_ha->forensic_info.data_buf.read_len =
pm8001_ha->forensic_info.data_buf.direct_len;
if (pm8001_ha->forensic_last_offset >= length_to_read) {
pm8001_ha->forensic_info.data_buf.direct_data +=
sprintf(pm8001_ha->forensic_info.data_buf.direct_data,
"%08x ", 3);
for (index = 0; index <
(pm8001_ha->forensic_info.data_buf.direct_len
/ 4); index++) {
pm8001_ha->forensic_info.data_buf.direct_data +=
sprintf(
pm8001_ha->forensic_info.data_buf.direct_data,
"%08x ", *(temp + index));
}
pm8001_ha->fatal_bar_loc = 0;
pm8001_ha->forensic_fatal_step = 1;
pm8001_ha->fatal_forensic_shift_offset = 0;
pm8001_ha->forensic_last_offset = 0;
status = 0;
offset = (int)
((char *)pm8001_ha->forensic_info.data_buf.direct_data
- (char *)buf);
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("get_fatal_spcv:return1 0x%x\n", offset));
return (char *)pm8001_ha->
forensic_info.data_buf.direct_data -
(char *)buf;
}
if (pm8001_ha->fatal_bar_loc < (64 * 1024)) {
pm8001_ha->forensic_info.data_buf.direct_data +=
sprintf(pm8001_ha->
forensic_info.data_buf.direct_data,
"%08x ", 2);
for (index = 0; index <
(pm8001_ha->forensic_info.data_buf.direct_len
/ 4); index++) {
pm8001_ha->forensic_info.data_buf.direct_data
+= sprintf(pm8001_ha->
forensic_info.data_buf.direct_data,
"%08x ", *(temp + index));
}
status = 0;
offset = (int)
((char *)pm8001_ha->forensic_info.data_buf.direct_data
- (char *)buf);
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("get_fatal_spcv:return2 0x%x\n", offset));
return (char *)pm8001_ha->
forensic_info.data_buf.direct_data -
(char *)buf;
}
/* Increment the MEMBASE II Shifting Register value by 0x100.*/
pm8001_ha->forensic_info.data_buf.direct_data +=
sprintf(pm8001_ha->forensic_info.data_buf.direct_data,
"%08x ", 2);
for (index = 0; index <
(pm8001_ha->forensic_info.data_buf.direct_len
/ 4) ; index++) {
pm8001_ha->forensic_info.data_buf.direct_data +=
sprintf(pm8001_ha->
forensic_info.data_buf.direct_data,
"%08x ", *(temp + index));
}
pm8001_ha->fatal_forensic_shift_offset += 0x100;
pm8001_cw32(pm8001_ha, 0, MEMBASE_II_SHIFT_REGISTER,
pm8001_ha->fatal_forensic_shift_offset);
pm8001_ha->fatal_bar_loc = 0;
status = 0;
offset = (int)
((char *)pm8001_ha->forensic_info.data_buf.direct_data
- (char *)buf);
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("get_fatal_spcv: return3 0x%x\n", offset));
return (char *)pm8001_ha->forensic_info.data_buf.direct_data -
(char *)buf;
}
if (pm8001_ha->forensic_fatal_step == 1) {
/* store previous accumulated length before triggering next
* accumulated length update
*/
pm8001_ha->forensic_preserved_accumulated_transfer =
pm8001_mr32(fatal_table_address,
MPI_FATAL_EDUMP_TABLE_ACCUM_LEN);
/* continue capturing the fatal log until Dump status is 0x3 */
if (pm8001_mr32(fatal_table_address,
MPI_FATAL_EDUMP_TABLE_STATUS) <
MPI_FATAL_EDUMP_TABLE_STAT_NF_SUCCESS_DONE) {
/* reset fddstat bit by writing to zero*/
pm8001_mw32(fatal_table_address,
MPI_FATAL_EDUMP_TABLE_STATUS, 0x0);
/* set dump control value to '1' so that new data will
* be transferred to shared memory
*/
pm8001_mw32(fatal_table_address,
MPI_FATAL_EDUMP_TABLE_HANDSHAKE,
MPI_FATAL_EDUMP_HANDSHAKE_RDY);
/*Poll FDDHSHK until clear */
start = jiffies + (2 * HZ); /* 2 sec */
do {
reg_val = pm8001_mr32(fatal_table_address,
MPI_FATAL_EDUMP_TABLE_HANDSHAKE);
} while ((reg_val) && time_before(jiffies, start));
if (reg_val != 0) {
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk(
"TIMEOUT:MPI_FATAL_EDUMP_TABLE_HDSHAKE 0x%x\n",
reg_val));
/* Fail the dump if a timeout occurs */
pm8001_ha->forensic_info.data_buf.direct_data +=
sprintf(
pm8001_ha->forensic_info.data_buf.direct_data,
"%08x ", 0xFFFFFFFF);
return((char *)
pm8001_ha->forensic_info.data_buf.direct_data
- (char *)buf);
}
/* Poll status register until set to 2 or
* 3 for up to 2 seconds
*/
start = jiffies + (2 * HZ); /* 2 sec */
do {
reg_val = pm8001_mr32(fatal_table_address,
MPI_FATAL_EDUMP_TABLE_STATUS);
} while (((reg_val != 2) && (reg_val != 3)) &&
time_before(jiffies, start));
if (reg_val < 2) {
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk(
"TIMEOUT:MPI_FATAL_EDUMP_TABLE_STATUS = 0x%x\n",
reg_val));
/* Fail the dump if a timeout occurs */
pm8001_ha->forensic_info.data_buf.direct_data +=
sprintf(
pm8001_ha->forensic_info.data_buf.direct_data,
"%08x ", 0xFFFFFFFF);
pm8001_cw32(pm8001_ha, 0,
MEMBASE_II_SHIFT_REGISTER,
pm8001_ha->fatal_forensic_shift_offset);
}
/* Read the next block of the debug data.*/
length_to_read = pm8001_mr32(fatal_table_address,
MPI_FATAL_EDUMP_TABLE_ACCUM_LEN) -
pm8001_ha->forensic_preserved_accumulated_transfer;
if (length_to_read != 0x0) {
pm8001_ha->forensic_fatal_step = 0;
goto moreData;
} else {
pm8001_ha->forensic_info.data_buf.direct_data +=
sprintf(
pm8001_ha->forensic_info.data_buf.direct_data,
"%08x ", 4);
pm8001_ha->forensic_info.data_buf.read_len
= 0xFFFFFFFF;
pm8001_ha->forensic_info.data_buf.direct_len
= 0;
pm8001_ha->forensic_info.data_buf.direct_offset
= 0;
pm8001_ha->forensic_info.data_buf.read_len = 0;
}
}
}
offset = (int)((char *)pm8001_ha->forensic_info.data_buf.direct_data
- (char *)buf);
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("get_fatal_spcv: return4 0x%x\n", offset));
return (char *)pm8001_ha->forensic_info.data_buf.direct_data -
(char *)buf;
}
/* pm80xx_get_non_fatal_dump - dump the nonfatal data from the dma
* location by the firmware.
*/
ssize_t pm80xx_get_non_fatal_dump(struct device *cdev,
struct device_attribute *attr, char *buf)
{
struct Scsi_Host *shost = class_to_shost(cdev);
struct sas_ha_struct *sha = SHOST_TO_SAS_HA(shost);
struct pm8001_hba_info *pm8001_ha = sha->lldd_ha;
void __iomem *nonfatal_table_address = pm8001_ha->fatal_tbl_addr;
u32 accum_len = 0;
u32 total_len = 0;
u32 reg_val = 0;
u32 *temp = NULL;
u32 index = 0;
u32 output_length;
unsigned long start = 0;
char *buf_copy = buf;
temp = (u32 *)pm8001_ha->memoryMap.region[FORENSIC_MEM].virt_ptr;
if (++pm8001_ha->non_fatal_count == 1) {
if (pm8001_ha->chip_id == chip_8001) {
snprintf(pm8001_ha->forensic_info.data_buf.direct_data,
PAGE_SIZE, "Not supported for SPC controller");
return 0;
}
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("forensic_info TYPE_NON_FATAL...\n"));
/*
* Step 1: Write the host buffer parameters in the MPI Fatal and
* Non-Fatal Error Dump Capture Table.This is the buffer
* where debug data will be DMAed to.
*/
pm8001_mw32(nonfatal_table_address,
MPI_FATAL_EDUMP_TABLE_LO_OFFSET,
pm8001_ha->memoryMap.region[FORENSIC_MEM].phys_addr_lo);
pm8001_mw32(nonfatal_table_address,
MPI_FATAL_EDUMP_TABLE_HI_OFFSET,
pm8001_ha->memoryMap.region[FORENSIC_MEM].phys_addr_hi);
pm8001_mw32(nonfatal_table_address,
MPI_FATAL_EDUMP_TABLE_LENGTH, SYSFS_OFFSET);
/* Optionally, set the DUMPCTRL bit to 1 if the host
* keeps sending active I/Os while capturing the non-fatal
* debug data. Otherwise, leave this bit set to zero
*/
pm8001_mw32(nonfatal_table_address,
MPI_FATAL_EDUMP_TABLE_HANDSHAKE, MPI_FATAL_EDUMP_HANDSHAKE_RDY);
/*
* Step 2: Clear Accumulative Length of Debug Data Transferred
* [ACCDDLEN] field in the MPI Fatal and Non-Fatal Error Dump
* Capture Table to zero.
*/
pm8001_mw32(nonfatal_table_address,
MPI_FATAL_EDUMP_TABLE_ACCUM_LEN, 0);
/* initiallize previous accumulated length to 0 */
pm8001_ha->forensic_preserved_accumulated_transfer = 0;
pm8001_ha->non_fatal_read_length = 0;
}
total_len = pm8001_mr32(nonfatal_table_address,
MPI_FATAL_EDUMP_TABLE_TOTAL_LEN);
/*
* Step 3:Clear Fatal/Non-Fatal Debug Data Transfer Status [FDDTSTAT]
* field and then request that the SPCv controller transfer the debug
* data by setting bit 7 of the Inbound Doorbell Set Register.
*/
pm8001_mw32(nonfatal_table_address, MPI_FATAL_EDUMP_TABLE_STATUS, 0);
pm8001_cw32(pm8001_ha, 0, MSGU_IBDB_SET,
SPCv_MSGU_CFG_TABLE_NONFATAL_DUMP);
/*
* Step 4.1: Read back the Inbound Doorbell Set Register (by polling for
* 2 seconds) until register bit 7 is cleared.
* This step only indicates the request is accepted by the controller.
*/
start = jiffies + (2 * HZ); /* 2 sec */
do {
reg_val = pm8001_cr32(pm8001_ha, 0, MSGU_IBDB_SET) &
SPCv_MSGU_CFG_TABLE_NONFATAL_DUMP;
} while ((reg_val != 0) && time_before(jiffies, start));
/* Step 4.2: To check the completion of the transfer, poll the Fatal/Non
* Fatal Debug Data Transfer Status [FDDTSTAT] field for 2 seconds in
* the MPI Fatal and Non-Fatal Error Dump Capture Table.
*/
start = jiffies + (2 * HZ); /* 2 sec */
do {
reg_val = pm8001_mr32(nonfatal_table_address,
MPI_FATAL_EDUMP_TABLE_STATUS);
} while ((!reg_val) && time_before(jiffies, start));
if ((reg_val == 0x00) ||
(reg_val == MPI_FATAL_EDUMP_TABLE_STAT_DMA_FAILED) ||
(reg_val > MPI_FATAL_EDUMP_TABLE_STAT_NF_SUCCESS_DONE)) {
pm8001_ha->non_fatal_read_length = 0;
buf_copy += snprintf(buf_copy, PAGE_SIZE, "%08x ", 0xFFFFFFFF);
pm8001_ha->non_fatal_count = 0;
return (buf_copy - buf);
} else if (reg_val ==
MPI_FATAL_EDUMP_TABLE_STAT_NF_SUCCESS_MORE_DATA) {
buf_copy += snprintf(buf_copy, PAGE_SIZE, "%08x ", 2);
} else if ((reg_val == MPI_FATAL_EDUMP_TABLE_STAT_NF_SUCCESS_DONE) ||
(pm8001_ha->non_fatal_read_length >= total_len)) {
pm8001_ha->non_fatal_read_length = 0;
buf_copy += snprintf(buf_copy, PAGE_SIZE, "%08x ", 4);
pm8001_ha->non_fatal_count = 0;
}
accum_len = pm8001_mr32(nonfatal_table_address,
MPI_FATAL_EDUMP_TABLE_ACCUM_LEN);
output_length = accum_len -
pm8001_ha->forensic_preserved_accumulated_transfer;
for (index = 0; index < output_length/4; index++)
buf_copy += snprintf(buf_copy, PAGE_SIZE,
"%08x ", *(temp+index));
pm8001_ha->non_fatal_read_length += output_length;
/* store current accumulated length to use in next iteration as
* the previous accumulated length
*/
pm8001_ha->forensic_preserved_accumulated_transfer = accum_len;
return (buf_copy - buf);
}
/**
* read_main_config_table - read the configure table and save it.
* @pm8001_ha: our hba card information
*/
static void read_main_config_table(struct pm8001_hba_info *pm8001_ha)
{
void __iomem *address = pm8001_ha->main_cfg_tbl_addr;
pm8001_ha->main_cfg_tbl.pm80xx_tbl.signature =
pm8001_mr32(address, MAIN_SIGNATURE_OFFSET);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.interface_rev =
pm8001_mr32(address, MAIN_INTERFACE_REVISION);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.firmware_rev =
pm8001_mr32(address, MAIN_FW_REVISION);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.max_out_io =
pm8001_mr32(address, MAIN_MAX_OUTSTANDING_IO_OFFSET);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.max_sgl =
pm8001_mr32(address, MAIN_MAX_SGL_OFFSET);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.ctrl_cap_flag =
pm8001_mr32(address, MAIN_CNTRL_CAP_OFFSET);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.gst_offset =
pm8001_mr32(address, MAIN_GST_OFFSET);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.inbound_queue_offset =
pm8001_mr32(address, MAIN_IBQ_OFFSET);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.outbound_queue_offset =
pm8001_mr32(address, MAIN_OBQ_OFFSET);
/* read Error Dump Offset and Length */
pm8001_ha->main_cfg_tbl.pm80xx_tbl.fatal_err_dump_offset0 =
pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP0_OFFSET);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.fatal_err_dump_length0 =
pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP0_LENGTH);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.fatal_err_dump_offset1 =
pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP1_OFFSET);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.fatal_err_dump_length1 =
pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP1_LENGTH);
/* read GPIO LED settings from the configuration table */
pm8001_ha->main_cfg_tbl.pm80xx_tbl.gpio_led_mapping =
pm8001_mr32(address, MAIN_GPIO_LED_FLAGS_OFFSET);
/* read analog Setting offset from the configuration table */
pm8001_ha->main_cfg_tbl.pm80xx_tbl.analog_setup_table_offset =
pm8001_mr32(address, MAIN_ANALOG_SETUP_OFFSET);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.int_vec_table_offset =
pm8001_mr32(address, MAIN_INT_VECTOR_TABLE_OFFSET);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.phy_attr_table_offset =
pm8001_mr32(address, MAIN_SAS_PHY_ATTR_TABLE_OFFSET);
/* read port recover and reset timeout */
pm8001_ha->main_cfg_tbl.pm80xx_tbl.port_recovery_timer =
pm8001_mr32(address, MAIN_PORT_RECOVERY_TIMER);
/* read ILA and inactive firmware version */
pm8001_ha->main_cfg_tbl.pm80xx_tbl.ila_version =
pm8001_mr32(address, MAIN_MPI_ILA_RELEASE_TYPE);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.inc_fw_version =
pm8001_mr32(address, MAIN_MPI_INACTIVE_FW_VERSION);
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"Main cfg table: sign:%x interface rev:%x fw_rev:%x\n",
pm8001_ha->main_cfg_tbl.pm80xx_tbl.signature,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.interface_rev,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.firmware_rev));
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"table offset: gst:%x iq:%x oq:%x int vec:%x phy attr:%x\n",
pm8001_ha->main_cfg_tbl.pm80xx_tbl.gst_offset,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.inbound_queue_offset,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.outbound_queue_offset,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.int_vec_table_offset,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.phy_attr_table_offset));
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"Main cfg table; ila rev:%x Inactive fw rev:%x\n",
pm8001_ha->main_cfg_tbl.pm80xx_tbl.ila_version,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.inc_fw_version));
}
/**
* read_general_status_table - read the general status table and save it.
* @pm8001_ha: our hba card information
*/
static void read_general_status_table(struct pm8001_hba_info *pm8001_ha)
{
void __iomem *address = pm8001_ha->general_stat_tbl_addr;
pm8001_ha->gs_tbl.pm80xx_tbl.gst_len_mpistate =
pm8001_mr32(address, GST_GSTLEN_MPIS_OFFSET);
pm8001_ha->gs_tbl.pm80xx_tbl.iq_freeze_state0 =
pm8001_mr32(address, GST_IQ_FREEZE_STATE0_OFFSET);
pm8001_ha->gs_tbl.pm80xx_tbl.iq_freeze_state1 =
pm8001_mr32(address, GST_IQ_FREEZE_STATE1_OFFSET);
pm8001_ha->gs_tbl.pm80xx_tbl.msgu_tcnt =
pm8001_mr32(address, GST_MSGUTCNT_OFFSET);
pm8001_ha->gs_tbl.pm80xx_tbl.iop_tcnt =
pm8001_mr32(address, GST_IOPTCNT_OFFSET);
pm8001_ha->gs_tbl.pm80xx_tbl.gpio_input_val =
pm8001_mr32(address, GST_GPIO_INPUT_VAL);
pm8001_ha->gs_tbl.pm80xx_tbl.recover_err_info[0] =
pm8001_mr32(address, GST_RERRINFO_OFFSET0);
pm8001_ha->gs_tbl.pm80xx_tbl.recover_err_info[1] =
pm8001_mr32(address, GST_RERRINFO_OFFSET1);
pm8001_ha->gs_tbl.pm80xx_tbl.recover_err_info[2] =
pm8001_mr32(address, GST_RERRINFO_OFFSET2);
pm8001_ha->gs_tbl.pm80xx_tbl.recover_err_info[3] =
pm8001_mr32(address, GST_RERRINFO_OFFSET3);
pm8001_ha->gs_tbl.pm80xx_tbl.recover_err_info[4] =
pm8001_mr32(address, GST_RERRINFO_OFFSET4);
pm8001_ha->gs_tbl.pm80xx_tbl.recover_err_info[5] =
pm8001_mr32(address, GST_RERRINFO_OFFSET5);
pm8001_ha->gs_tbl.pm80xx_tbl.recover_err_info[6] =
pm8001_mr32(address, GST_RERRINFO_OFFSET6);
pm8001_ha->gs_tbl.pm80xx_tbl.recover_err_info[7] =
pm8001_mr32(address, GST_RERRINFO_OFFSET7);
}
/**
* read_phy_attr_table - read the phy attribute table and save it.
* @pm8001_ha: our hba card information
*/
static void read_phy_attr_table(struct pm8001_hba_info *pm8001_ha)
{
void __iomem *address = pm8001_ha->pspa_q_tbl_addr;
pm8001_ha->phy_attr_table.phystart1_16[0] =
pm8001_mr32(address, PSPA_PHYSTATE0_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[1] =
pm8001_mr32(address, PSPA_PHYSTATE1_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[2] =
pm8001_mr32(address, PSPA_PHYSTATE2_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[3] =
pm8001_mr32(address, PSPA_PHYSTATE3_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[4] =
pm8001_mr32(address, PSPA_PHYSTATE4_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[5] =
pm8001_mr32(address, PSPA_PHYSTATE5_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[6] =
pm8001_mr32(address, PSPA_PHYSTATE6_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[7] =
pm8001_mr32(address, PSPA_PHYSTATE7_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[8] =
pm8001_mr32(address, PSPA_PHYSTATE8_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[9] =
pm8001_mr32(address, PSPA_PHYSTATE9_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[10] =
pm8001_mr32(address, PSPA_PHYSTATE10_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[11] =
pm8001_mr32(address, PSPA_PHYSTATE11_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[12] =
pm8001_mr32(address, PSPA_PHYSTATE12_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[13] =
pm8001_mr32(address, PSPA_PHYSTATE13_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[14] =
pm8001_mr32(address, PSPA_PHYSTATE14_OFFSET);
pm8001_ha->phy_attr_table.phystart1_16[15] =
pm8001_mr32(address, PSPA_PHYSTATE15_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[0] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID0_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[1] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID1_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[2] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID2_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[3] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID3_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[4] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID4_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[5] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID5_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[6] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID6_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[7] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID7_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[8] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID8_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[9] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID9_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[10] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID10_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[11] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID11_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[12] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID12_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[13] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID13_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[14] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID14_OFFSET);
pm8001_ha->phy_attr_table.outbound_hw_event_pid1_16[15] =
pm8001_mr32(address, PSPA_OB_HW_EVENT_PID15_OFFSET);
}
/**
* read_inbnd_queue_table - read the inbound queue table and save it.
* @pm8001_ha: our hba card information
*/
static void read_inbnd_queue_table(struct pm8001_hba_info *pm8001_ha)
{
int i;
void __iomem *address = pm8001_ha->inbnd_q_tbl_addr;
for (i = 0; i < PM8001_MAX_SPCV_INB_NUM; i++) {
u32 offset = i * 0x20;
pm8001_ha->inbnd_q_tbl[i].pi_pci_bar =
get_pci_bar_index(pm8001_mr32(address,
(offset + IB_PIPCI_BAR)));
pm8001_ha->inbnd_q_tbl[i].pi_offset =
pm8001_mr32(address, (offset + IB_PIPCI_BAR_OFFSET));
}
}
/**
* read_outbnd_queue_table - read the outbound queue table and save it.
* @pm8001_ha: our hba card information
*/
static void read_outbnd_queue_table(struct pm8001_hba_info *pm8001_ha)
{
int i;
void __iomem *address = pm8001_ha->outbnd_q_tbl_addr;
for (i = 0; i < PM8001_MAX_SPCV_OUTB_NUM; i++) {
u32 offset = i * 0x24;
pm8001_ha->outbnd_q_tbl[i].ci_pci_bar =
get_pci_bar_index(pm8001_mr32(address,
(offset + OB_CIPCI_BAR)));
pm8001_ha->outbnd_q_tbl[i].ci_offset =
pm8001_mr32(address, (offset + OB_CIPCI_BAR_OFFSET));
}
}
/**
* init_default_table_values - init the default table.
* @pm8001_ha: our hba card information
*/
static void init_default_table_values(struct pm8001_hba_info *pm8001_ha)
{
int i;
u32 offsetib, offsetob;
void __iomem *addressib = pm8001_ha->inbnd_q_tbl_addr;
void __iomem *addressob = pm8001_ha->outbnd_q_tbl_addr;
pm8001_ha->main_cfg_tbl.pm80xx_tbl.upper_event_log_addr =
pm8001_ha->memoryMap.region[AAP1].phys_addr_hi;
pm8001_ha->main_cfg_tbl.pm80xx_tbl.lower_event_log_addr =
pm8001_ha->memoryMap.region[AAP1].phys_addr_lo;
pm8001_ha->main_cfg_tbl.pm80xx_tbl.event_log_size =
PM8001_EVENT_LOG_SIZE;
pm8001_ha->main_cfg_tbl.pm80xx_tbl.event_log_severity = 0x01;
pm8001_ha->main_cfg_tbl.pm80xx_tbl.upper_pcs_event_log_addr =
pm8001_ha->memoryMap.region[IOP].phys_addr_hi;
pm8001_ha->main_cfg_tbl.pm80xx_tbl.lower_pcs_event_log_addr =
pm8001_ha->memoryMap.region[IOP].phys_addr_lo;
pm8001_ha->main_cfg_tbl.pm80xx_tbl.pcs_event_log_size =
PM8001_EVENT_LOG_SIZE;
pm8001_ha->main_cfg_tbl.pm80xx_tbl.pcs_event_log_severity = 0x01;
pm8001_ha->main_cfg_tbl.pm80xx_tbl.fatal_err_interrupt = 0x01;
/* Disable end to end CRC checking */
pm8001_ha->main_cfg_tbl.pm80xx_tbl.crc_core_dump = (0x1 << 16);
for (i = 0; i < PM8001_MAX_SPCV_INB_NUM; i++) {
pm8001_ha->inbnd_q_tbl[i].element_pri_size_cnt =
PM8001_MPI_QUEUE | (pm8001_ha->iomb_size << 16) | (0x00<<30);
pm8001_ha->inbnd_q_tbl[i].upper_base_addr =
pm8001_ha->memoryMap.region[IB + i].phys_addr_hi;
pm8001_ha->inbnd_q_tbl[i].lower_base_addr =
pm8001_ha->memoryMap.region[IB + i].phys_addr_lo;
pm8001_ha->inbnd_q_tbl[i].base_virt =
(u8 *)pm8001_ha->memoryMap.region[IB + i].virt_ptr;
pm8001_ha->inbnd_q_tbl[i].total_length =
pm8001_ha->memoryMap.region[IB + i].total_len;
pm8001_ha->inbnd_q_tbl[i].ci_upper_base_addr =
pm8001_ha->memoryMap.region[CI + i].phys_addr_hi;
pm8001_ha->inbnd_q_tbl[i].ci_lower_base_addr =
pm8001_ha->memoryMap.region[CI + i].phys_addr_lo;
pm8001_ha->inbnd_q_tbl[i].ci_virt =
pm8001_ha->memoryMap.region[CI + i].virt_ptr;
offsetib = i * 0x20;
pm8001_ha->inbnd_q_tbl[i].pi_pci_bar =
get_pci_bar_index(pm8001_mr32(addressib,
(offsetib + 0x14)));
pm8001_ha->inbnd_q_tbl[i].pi_offset =
pm8001_mr32(addressib, (offsetib + 0x18));
pm8001_ha->inbnd_q_tbl[i].producer_idx = 0;
pm8001_ha->inbnd_q_tbl[i].consumer_index = 0;
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"IQ %d pi_bar 0x%x pi_offset 0x%x\n", i,
pm8001_ha->inbnd_q_tbl[i].pi_pci_bar,
pm8001_ha->inbnd_q_tbl[i].pi_offset));
}
for (i = 0; i < PM8001_MAX_SPCV_OUTB_NUM; i++) {
pm8001_ha->outbnd_q_tbl[i].element_size_cnt =
PM8001_MPI_QUEUE | (pm8001_ha->iomb_size << 16) | (0x01<<30);
pm8001_ha->outbnd_q_tbl[i].upper_base_addr =
pm8001_ha->memoryMap.region[OB + i].phys_addr_hi;
pm8001_ha->outbnd_q_tbl[i].lower_base_addr =
pm8001_ha->memoryMap.region[OB + i].phys_addr_lo;
pm8001_ha->outbnd_q_tbl[i].base_virt =
(u8 *)pm8001_ha->memoryMap.region[OB + i].virt_ptr;
pm8001_ha->outbnd_q_tbl[i].total_length =
pm8001_ha->memoryMap.region[OB + i].total_len;
pm8001_ha->outbnd_q_tbl[i].pi_upper_base_addr =
pm8001_ha->memoryMap.region[PI + i].phys_addr_hi;
pm8001_ha->outbnd_q_tbl[i].pi_lower_base_addr =
pm8001_ha->memoryMap.region[PI + i].phys_addr_lo;
/* interrupt vector based on oq */
pm8001_ha->outbnd_q_tbl[i].interrup_vec_cnt_delay = (i << 24);
pm8001_ha->outbnd_q_tbl[i].pi_virt =
pm8001_ha->memoryMap.region[PI + i].virt_ptr;
offsetob = i * 0x24;
pm8001_ha->outbnd_q_tbl[i].ci_pci_bar =
get_pci_bar_index(pm8001_mr32(addressob,
offsetob + 0x14));
pm8001_ha->outbnd_q_tbl[i].ci_offset =
pm8001_mr32(addressob, (offsetob + 0x18));
pm8001_ha->outbnd_q_tbl[i].consumer_idx = 0;
pm8001_ha->outbnd_q_tbl[i].producer_index = 0;
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"OQ %d ci_bar 0x%x ci_offset 0x%x\n", i,
pm8001_ha->outbnd_q_tbl[i].ci_pci_bar,
pm8001_ha->outbnd_q_tbl[i].ci_offset));
}
}
/**
* update_main_config_table - update the main default table to the HBA.
* @pm8001_ha: our hba card information
*/
static void update_main_config_table(struct pm8001_hba_info *pm8001_ha)
{
void __iomem *address = pm8001_ha->main_cfg_tbl_addr;
pm8001_mw32(address, MAIN_IQNPPD_HPPD_OFFSET,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.inbound_q_nppd_hppd);
pm8001_mw32(address, MAIN_EVENT_LOG_ADDR_HI,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.upper_event_log_addr);
pm8001_mw32(address, MAIN_EVENT_LOG_ADDR_LO,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.lower_event_log_addr);
pm8001_mw32(address, MAIN_EVENT_LOG_BUFF_SIZE,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.event_log_size);
pm8001_mw32(address, MAIN_EVENT_LOG_OPTION,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.event_log_severity);
pm8001_mw32(address, MAIN_PCS_EVENT_LOG_ADDR_HI,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.upper_pcs_event_log_addr);
pm8001_mw32(address, MAIN_PCS_EVENT_LOG_ADDR_LO,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.lower_pcs_event_log_addr);
pm8001_mw32(address, MAIN_PCS_EVENT_LOG_BUFF_SIZE,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.pcs_event_log_size);
pm8001_mw32(address, MAIN_PCS_EVENT_LOG_OPTION,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.pcs_event_log_severity);
/* Update Fatal error interrupt vector */
pm8001_ha->main_cfg_tbl.pm80xx_tbl.fatal_err_interrupt |=
((pm8001_ha->number_of_intr - 1) << 8);
pm8001_mw32(address, MAIN_FATAL_ERROR_INTERRUPT,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.fatal_err_interrupt);
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"Updated Fatal error interrupt vector 0x%x\n",
pm8001_mr32(address, MAIN_FATAL_ERROR_INTERRUPT)));
pm8001_mw32(address, MAIN_EVENT_CRC_CHECK,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.crc_core_dump);
/* SPCv specific */
pm8001_ha->main_cfg_tbl.pm80xx_tbl.gpio_led_mapping &= 0xCFFFFFFF;
/* Set GPIOLED to 0x2 for LED indicator */
pm8001_ha->main_cfg_tbl.pm80xx_tbl.gpio_led_mapping |= 0x20000000;
pm8001_mw32(address, MAIN_GPIO_LED_FLAGS_OFFSET,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.gpio_led_mapping);
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"Programming DW 0x21 in main cfg table with 0x%x\n",
pm8001_mr32(address, MAIN_GPIO_LED_FLAGS_OFFSET)));
pm8001_mw32(address, MAIN_PORT_RECOVERY_TIMER,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.port_recovery_timer);
pm8001_mw32(address, MAIN_INT_REASSERTION_DELAY,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.interrupt_reassertion_delay);
pm8001_ha->main_cfg_tbl.pm80xx_tbl.port_recovery_timer &= 0xffff0000;
pm8001_ha->main_cfg_tbl.pm80xx_tbl.port_recovery_timer |=
PORT_RECOVERY_TIMEOUT;
if (pm8001_ha->chip_id == chip_8006) {
pm8001_ha->main_cfg_tbl.pm80xx_tbl.port_recovery_timer &=
0x0000ffff;
pm8001_ha->main_cfg_tbl.pm80xx_tbl.port_recovery_timer |=
CHIP_8006_PORT_RECOVERY_TIMEOUT;
}
pm8001_mw32(address, MAIN_PORT_RECOVERY_TIMER,
pm8001_ha->main_cfg_tbl.pm80xx_tbl.port_recovery_timer);
}
/**
* update_inbnd_queue_table - update the inbound queue table to the HBA.
* @pm8001_ha: our hba card information
*/
static void update_inbnd_queue_table(struct pm8001_hba_info *pm8001_ha,
int number)
{
void __iomem *address = pm8001_ha->inbnd_q_tbl_addr;
u16 offset = number * 0x20;
pm8001_mw32(address, offset + IB_PROPERITY_OFFSET,
pm8001_ha->inbnd_q_tbl[number].element_pri_size_cnt);
pm8001_mw32(address, offset + IB_BASE_ADDR_HI_OFFSET,
pm8001_ha->inbnd_q_tbl[number].upper_base_addr);
pm8001_mw32(address, offset + IB_BASE_ADDR_LO_OFFSET,
pm8001_ha->inbnd_q_tbl[number].lower_base_addr);
pm8001_mw32(address, offset + IB_CI_BASE_ADDR_HI_OFFSET,
pm8001_ha->inbnd_q_tbl[number].ci_upper_base_addr);
pm8001_mw32(address, offset + IB_CI_BASE_ADDR_LO_OFFSET,
pm8001_ha->inbnd_q_tbl[number].ci_lower_base_addr);
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"IQ %d: Element pri size 0x%x\n",
number,
pm8001_ha->inbnd_q_tbl[number].element_pri_size_cnt));
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"IQ upr base addr 0x%x IQ lwr base addr 0x%x\n",
pm8001_ha->inbnd_q_tbl[number].upper_base_addr,
pm8001_ha->inbnd_q_tbl[number].lower_base_addr));
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"CI upper base addr 0x%x CI lower base addr 0x%x\n",
pm8001_ha->inbnd_q_tbl[number].ci_upper_base_addr,
pm8001_ha->inbnd_q_tbl[number].ci_lower_base_addr));
}
/**
* update_outbnd_queue_table - update the outbound queue table to the HBA.
* @pm8001_ha: our hba card information
*/
static void update_outbnd_queue_table(struct pm8001_hba_info *pm8001_ha,
int number)
{
void __iomem *address = pm8001_ha->outbnd_q_tbl_addr;
u16 offset = number * 0x24;
pm8001_mw32(address, offset + OB_PROPERITY_OFFSET,
pm8001_ha->outbnd_q_tbl[number].element_size_cnt);
pm8001_mw32(address, offset + OB_BASE_ADDR_HI_OFFSET,
pm8001_ha->outbnd_q_tbl[number].upper_base_addr);
pm8001_mw32(address, offset + OB_BASE_ADDR_LO_OFFSET,
pm8001_ha->outbnd_q_tbl[number].lower_base_addr);
pm8001_mw32(address, offset + OB_PI_BASE_ADDR_HI_OFFSET,
pm8001_ha->outbnd_q_tbl[number].pi_upper_base_addr);
pm8001_mw32(address, offset + OB_PI_BASE_ADDR_LO_OFFSET,
pm8001_ha->outbnd_q_tbl[number].pi_lower_base_addr);
pm8001_mw32(address, offset + OB_INTERRUPT_COALES_OFFSET,
pm8001_ha->outbnd_q_tbl[number].interrup_vec_cnt_delay);
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"OQ %d: Element pri size 0x%x\n",
number,
pm8001_ha->outbnd_q_tbl[number].element_size_cnt));
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"OQ upr base addr 0x%x OQ lwr base addr 0x%x\n",
pm8001_ha->outbnd_q_tbl[number].upper_base_addr,
pm8001_ha->outbnd_q_tbl[number].lower_base_addr));
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"PI upper base addr 0x%x PI lower base addr 0x%x\n",
pm8001_ha->outbnd_q_tbl[number].pi_upper_base_addr,
pm8001_ha->outbnd_q_tbl[number].pi_lower_base_addr));
}
/**
* mpi_init_check - check firmware initialization status.
* @pm8001_ha: our hba card information
*/
static int mpi_init_check(struct pm8001_hba_info *pm8001_ha)
{
u32 max_wait_count;
u32 value;
u32 gst_len_mpistate;
/* Write bit0=1 to Inbound DoorBell Register to tell the SPC FW the
table is updated */
pm8001_cw32(pm8001_ha, 0, MSGU_IBDB_SET, SPCv_MSGU_CFG_TABLE_UPDATE);
/* wait until Inbound DoorBell Clear Register toggled */
if (IS_SPCV_12G(pm8001_ha->pdev)) {
max_wait_count = SPCV_DOORBELL_CLEAR_TIMEOUT;
} else {
max_wait_count = SPC_DOORBELL_CLEAR_TIMEOUT;
}
do {
udelay(1);
value = pm8001_cr32(pm8001_ha, 0, MSGU_IBDB_SET);
value &= SPCv_MSGU_CFG_TABLE_UPDATE;
} while ((value != 0) && (--max_wait_count));
if (!max_wait_count)
return -1;
/* check the MPI-State for initialization upto 100ms*/
max_wait_count = 100 * 1000;/* 100 msec */
do {
udelay(1);
gst_len_mpistate =
pm8001_mr32(pm8001_ha->general_stat_tbl_addr,
GST_GSTLEN_MPIS_OFFSET);
} while ((GST_MPI_STATE_INIT !=
(gst_len_mpistate & GST_MPI_STATE_MASK)) && (--max_wait_count));
if (!max_wait_count)
return -1;
/* check MPI Initialization error */
gst_len_mpistate = gst_len_mpistate >> 16;
if (0x0000 != gst_len_mpistate)
return -1;
return 0;
}
/**
* check_fw_ready - The LLDD check if the FW is ready, if not, return error.
* @pm8001_ha: our hba card information
*/
static int check_fw_ready(struct pm8001_hba_info *pm8001_ha)
{
u32 value;
u32 max_wait_count;
u32 max_wait_time;
int ret = 0;
/* reset / PCIe ready */
max_wait_time = max_wait_count = 100 * 1000; /* 100 milli sec */
do {
udelay(1);
value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
} while ((value == 0xFFFFFFFF) && (--max_wait_count));
/* check ila status */
max_wait_time = max_wait_count = 1000 * 1000; /* 1000 milli sec */
do {
udelay(1);
value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
} while (((value & SCRATCH_PAD_ILA_READY) !=
SCRATCH_PAD_ILA_READY) && (--max_wait_count));
if (!max_wait_count)
ret = -1;
else {
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" ila ready status in %d millisec\n",
(max_wait_time - max_wait_count)));
}
/* check RAAE status */
max_wait_time = max_wait_count = 1800 * 1000; /* 1800 milli sec */
do {
udelay(1);
value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
} while (((value & SCRATCH_PAD_RAAE_READY) !=
SCRATCH_PAD_RAAE_READY) && (--max_wait_count));
if (!max_wait_count)
ret = -1;
else {
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" raae ready status in %d millisec\n",
(max_wait_time - max_wait_count)));
}
/* check iop0 status */
max_wait_time = max_wait_count = 600 * 1000; /* 600 milli sec */
do {
udelay(1);
value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
} while (((value & SCRATCH_PAD_IOP0_READY) != SCRATCH_PAD_IOP0_READY) &&
(--max_wait_count));
if (!max_wait_count)
ret = -1;
else {
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" iop0 ready status in %d millisec\n",
(max_wait_time - max_wait_count)));
}
/* check iop1 status only for 16 port controllers */
if ((pm8001_ha->chip_id != chip_8008) &&
(pm8001_ha->chip_id != chip_8009)) {
/* 200 milli sec */
max_wait_time = max_wait_count = 200 * 1000;
do {
udelay(1);
value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
} while (((value & SCRATCH_PAD_IOP1_READY) !=
SCRATCH_PAD_IOP1_READY) && (--max_wait_count));
if (!max_wait_count)
ret = -1;
else {
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"iop1 ready status in %d millisec\n",
(max_wait_time - max_wait_count)));
}
}
return ret;
}
static void init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha)
{
void __iomem *base_addr;
u32 value;
u32 offset;
u32 pcibar;
u32 pcilogic;
value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0);
offset = value & 0x03FFFFFF; /* scratch pad 0 TBL address */
PM8001_DEV_DBG(pm8001_ha,
pm8001_printk("Scratchpad 0 Offset: 0x%x value 0x%x\n",
offset, value));
pcilogic = (value & 0xFC000000) >> 26;
pcibar = get_pci_bar_index(pcilogic);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("Scratchpad 0 PCI BAR: %d\n", pcibar));
pm8001_ha->main_cfg_tbl_addr = base_addr =
pm8001_ha->io_mem[pcibar].memvirtaddr + offset;
pm8001_ha->general_stat_tbl_addr =
base_addr + (pm8001_cr32(pm8001_ha, pcibar, offset + 0x18) &
0xFFFFFF);
pm8001_ha->inbnd_q_tbl_addr =
base_addr + (pm8001_cr32(pm8001_ha, pcibar, offset + 0x1C) &
0xFFFFFF);
pm8001_ha->outbnd_q_tbl_addr =
base_addr + (pm8001_cr32(pm8001_ha, pcibar, offset + 0x20) &
0xFFFFFF);
pm8001_ha->ivt_tbl_addr =
base_addr + (pm8001_cr32(pm8001_ha, pcibar, offset + 0x8C) &
0xFFFFFF);
pm8001_ha->pspa_q_tbl_addr =
base_addr + (pm8001_cr32(pm8001_ha, pcibar, offset + 0x90) &
0xFFFFFF);
pm8001_ha->fatal_tbl_addr =
base_addr + (pm8001_cr32(pm8001_ha, pcibar, offset + 0xA0) &
0xFFFFFF);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("GST OFFSET 0x%x\n",
pm8001_cr32(pm8001_ha, pcibar, offset + 0x18)));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("INBND OFFSET 0x%x\n",
pm8001_cr32(pm8001_ha, pcibar, offset + 0x1C)));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("OBND OFFSET 0x%x\n",
pm8001_cr32(pm8001_ha, pcibar, offset + 0x20)));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("IVT OFFSET 0x%x\n",
pm8001_cr32(pm8001_ha, pcibar, offset + 0x8C)));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("PSPA OFFSET 0x%x\n",
pm8001_cr32(pm8001_ha, pcibar, offset + 0x90)));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("addr - main cfg %p general status %p\n",
pm8001_ha->main_cfg_tbl_addr,
pm8001_ha->general_stat_tbl_addr));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("addr - inbnd %p obnd %p\n",
pm8001_ha->inbnd_q_tbl_addr,
pm8001_ha->outbnd_q_tbl_addr));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("addr - pspa %p ivt %p\n",
pm8001_ha->pspa_q_tbl_addr,
pm8001_ha->ivt_tbl_addr));
}
/**
* pm80xx_set_thermal_config - support the thermal configuration
* @pm8001_ha: our hba card information.
*/
int
pm80xx_set_thermal_config(struct pm8001_hba_info *pm8001_ha)
{
struct set_ctrl_cfg_req payload;
struct inbound_queue_table *circularQ;
int rc;
u32 tag;
u32 opc = OPC_INB_SET_CONTROLLER_CONFIG;
u32 page_code;
memset(&payload, 0, sizeof(struct set_ctrl_cfg_req));
rc = pm8001_tag_alloc(pm8001_ha, &tag);
if (rc)
return -1;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
payload.tag = cpu_to_le32(tag);
if (IS_SPCV_12G(pm8001_ha->pdev))
page_code = THERMAL_PAGE_CODE_7H;
else
page_code = THERMAL_PAGE_CODE_8H;
payload.cfg_pg[0] = (THERMAL_LOG_ENABLE << 9) |
(THERMAL_ENABLE << 8) | page_code;
payload.cfg_pg[1] = (LTEMPHIL << 24) | (RTEMPHIL << 8);
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"Setting up thermal config. cfg_pg 0 0x%x cfg_pg 1 0x%x\n",
payload.cfg_pg[0], payload.cfg_pg[1]));
rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload,
sizeof(payload), 0);
if (rc)
pm8001_tag_free(pm8001_ha, tag);
return rc;
}
/**
* pm80xx_set_sas_protocol_timer_config - support the SAS Protocol
* Timer configuration page
* @pm8001_ha: our hba card information.
*/
static int
pm80xx_set_sas_protocol_timer_config(struct pm8001_hba_info *pm8001_ha)
{
struct set_ctrl_cfg_req payload;
struct inbound_queue_table *circularQ;
SASProtocolTimerConfig_t SASConfigPage;
int rc;
u32 tag;
u32 opc = OPC_INB_SET_CONTROLLER_CONFIG;
memset(&payload, 0, sizeof(struct set_ctrl_cfg_req));
memset(&SASConfigPage, 0, sizeof(SASProtocolTimerConfig_t));
rc = pm8001_tag_alloc(pm8001_ha, &tag);
if (rc)
return -1;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
payload.tag = cpu_to_le32(tag);
SASConfigPage.pageCode = SAS_PROTOCOL_TIMER_CONFIG_PAGE;
SASConfigPage.MST_MSI = 3 << 15;
SASConfigPage.STP_SSP_MCT_TMO = (STP_MCT_TMO << 16) | SSP_MCT_TMO;
SASConfigPage.STP_FRM_TMO = (SAS_MAX_OPEN_TIME << 24) |
(SMP_MAX_CONN_TIMER << 16) | STP_FRM_TIMER;
SASConfigPage.STP_IDLE_TMO = STP_IDLE_TIME;
if (SASConfigPage.STP_IDLE_TMO > 0x3FFFFFF)
SASConfigPage.STP_IDLE_TMO = 0x3FFFFFF;
SASConfigPage.OPNRJT_RTRY_INTVL = (SAS_MFD << 16) |
SAS_OPNRJT_RTRY_INTVL;
SASConfigPage.Data_Cmd_OPNRJT_RTRY_TMO = (SAS_DOPNRJT_RTRY_TMO << 16)
| SAS_COPNRJT_RTRY_TMO;
SASConfigPage.Data_Cmd_OPNRJT_RTRY_THR = (SAS_DOPNRJT_RTRY_THR << 16)
| SAS_COPNRJT_RTRY_THR;
SASConfigPage.MAX_AIP = SAS_MAX_AIP;
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("SASConfigPage.pageCode "
"0x%08x\n", SASConfigPage.pageCode));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("SASConfigPage.MST_MSI "
" 0x%08x\n", SASConfigPage.MST_MSI));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("SASConfigPage.STP_SSP_MCT_TMO "
" 0x%08x\n", SASConfigPage.STP_SSP_MCT_TMO));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("SASConfigPage.STP_FRM_TMO "
" 0x%08x\n", SASConfigPage.STP_FRM_TMO));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("SASConfigPage.STP_IDLE_TMO "
" 0x%08x\n", SASConfigPage.STP_IDLE_TMO));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("SASConfigPage.OPNRJT_RTRY_INTVL "
" 0x%08x\n", SASConfigPage.OPNRJT_RTRY_INTVL));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("SASConfigPage.Data_Cmd_OPNRJT_RTRY_TMO "
" 0x%08x\n", SASConfigPage.Data_Cmd_OPNRJT_RTRY_TMO));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("SASConfigPage.Data_Cmd_OPNRJT_RTRY_THR "
" 0x%08x\n", SASConfigPage.Data_Cmd_OPNRJT_RTRY_THR));
PM8001_INIT_DBG(pm8001_ha, pm8001_printk("SASConfigPage.MAX_AIP "
" 0x%08x\n", SASConfigPage.MAX_AIP));
memcpy(&payload.cfg_pg, &SASConfigPage,
sizeof(SASProtocolTimerConfig_t));
rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload,
sizeof(payload), 0);
if (rc)
pm8001_tag_free(pm8001_ha, tag);
return rc;
}
/**
* pm80xx_get_encrypt_info - Check for encryption
* @pm8001_ha: our hba card information.
*/
static int
pm80xx_get_encrypt_info(struct pm8001_hba_info *pm8001_ha)
{
u32 scratch3_value;
int ret = -1;
/* Read encryption status from SCRATCH PAD 3 */
scratch3_value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_3);
if ((scratch3_value & SCRATCH_PAD3_ENC_MASK) ==
SCRATCH_PAD3_ENC_READY) {
if (scratch3_value & SCRATCH_PAD3_XTS_ENABLED)
pm8001_ha->encrypt_info.cipher_mode = CIPHER_MODE_XTS;
if ((scratch3_value & SCRATCH_PAD3_SM_MASK) ==
SCRATCH_PAD3_SMF_ENABLED)
pm8001_ha->encrypt_info.sec_mode = SEC_MODE_SMF;
if ((scratch3_value & SCRATCH_PAD3_SM_MASK) ==
SCRATCH_PAD3_SMA_ENABLED)
pm8001_ha->encrypt_info.sec_mode = SEC_MODE_SMA;
if ((scratch3_value & SCRATCH_PAD3_SM_MASK) ==
SCRATCH_PAD3_SMB_ENABLED)
pm8001_ha->encrypt_info.sec_mode = SEC_MODE_SMB;
pm8001_ha->encrypt_info.status = 0;
PM8001_INIT_DBG(pm8001_ha, pm8001_printk(
"Encryption: SCRATCH_PAD3_ENC_READY 0x%08X."
"Cipher mode 0x%x Sec mode 0x%x status 0x%x\n",
scratch3_value, pm8001_ha->encrypt_info.cipher_mode,
pm8001_ha->encrypt_info.sec_mode,
pm8001_ha->encrypt_info.status));
ret = 0;
} else if ((scratch3_value & SCRATCH_PAD3_ENC_READY) ==
SCRATCH_PAD3_ENC_DISABLED) {
PM8001_INIT_DBG(pm8001_ha, pm8001_printk(
"Encryption: SCRATCH_PAD3_ENC_DISABLED 0x%08X\n",
scratch3_value));
pm8001_ha->encrypt_info.status = 0xFFFFFFFF;
pm8001_ha->encrypt_info.cipher_mode = 0;
pm8001_ha->encrypt_info.sec_mode = 0;
ret = 0;
} else if ((scratch3_value & SCRATCH_PAD3_ENC_MASK) ==
SCRATCH_PAD3_ENC_DIS_ERR) {
pm8001_ha->encrypt_info.status =
(scratch3_value & SCRATCH_PAD3_ERR_CODE) >> 16;
if (scratch3_value & SCRATCH_PAD3_XTS_ENABLED)
pm8001_ha->encrypt_info.cipher_mode = CIPHER_MODE_XTS;
if ((scratch3_value & SCRATCH_PAD3_SM_MASK) ==
SCRATCH_PAD3_SMF_ENABLED)
pm8001_ha->encrypt_info.sec_mode = SEC_MODE_SMF;
if ((scratch3_value & SCRATCH_PAD3_SM_MASK) ==
SCRATCH_PAD3_SMA_ENABLED)
pm8001_ha->encrypt_info.sec_mode = SEC_MODE_SMA;
if ((scratch3_value & SCRATCH_PAD3_SM_MASK) ==
SCRATCH_PAD3_SMB_ENABLED)
pm8001_ha->encrypt_info.sec_mode = SEC_MODE_SMB;
PM8001_INIT_DBG(pm8001_ha, pm8001_printk(
"Encryption: SCRATCH_PAD3_DIS_ERR 0x%08X."
"Cipher mode 0x%x sec mode 0x%x status 0x%x\n",
scratch3_value, pm8001_ha->encrypt_info.cipher_mode,
pm8001_ha->encrypt_info.sec_mode,
pm8001_ha->encrypt_info.status));
} else if ((scratch3_value & SCRATCH_PAD3_ENC_MASK) ==
SCRATCH_PAD3_ENC_ENA_ERR) {
pm8001_ha->encrypt_info.status =
(scratch3_value & SCRATCH_PAD3_ERR_CODE) >> 16;
if (scratch3_value & SCRATCH_PAD3_XTS_ENABLED)
pm8001_ha->encrypt_info.cipher_mode = CIPHER_MODE_XTS;
if ((scratch3_value & SCRATCH_PAD3_SM_MASK) ==
SCRATCH_PAD3_SMF_ENABLED)
pm8001_ha->encrypt_info.sec_mode = SEC_MODE_SMF;
if ((scratch3_value & SCRATCH_PAD3_SM_MASK) ==
SCRATCH_PAD3_SMA_ENABLED)
pm8001_ha->encrypt_info.sec_mode = SEC_MODE_SMA;
if ((scratch3_value & SCRATCH_PAD3_SM_MASK) ==
SCRATCH_PAD3_SMB_ENABLED)
pm8001_ha->encrypt_info.sec_mode = SEC_MODE_SMB;
PM8001_INIT_DBG(pm8001_ha, pm8001_printk(
"Encryption: SCRATCH_PAD3_ENA_ERR 0x%08X."
"Cipher mode 0x%x sec mode 0x%x status 0x%x\n",
scratch3_value, pm8001_ha->encrypt_info.cipher_mode,
pm8001_ha->encrypt_info.sec_mode,
pm8001_ha->encrypt_info.status));
}
return ret;
}
/**
* pm80xx_encrypt_update - update flash with encryption informtion
* @pm8001_ha: our hba card information.
*/
static int pm80xx_encrypt_update(struct pm8001_hba_info *pm8001_ha)
{
struct kek_mgmt_req payload;
struct inbound_queue_table *circularQ;
int rc;
u32 tag;
u32 opc = OPC_INB_KEK_MANAGEMENT;
memset(&payload, 0, sizeof(struct kek_mgmt_req));
rc = pm8001_tag_alloc(pm8001_ha, &tag);
if (rc)
return -1;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
payload.tag = cpu_to_le32(tag);
/* Currently only one key is used. New KEK index is 1.
* Current KEK index is 1. Store KEK to NVRAM is 1.
*/
payload.new_curidx_ksop = ((1 << 24) | (1 << 16) | (1 << 8) |
KEK_MGMT_SUBOP_KEYCARDUPDATE);
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"Saving Encryption info to flash. payload 0x%x\n",
payload.new_curidx_ksop));
rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload,
sizeof(payload), 0);
if (rc)
pm8001_tag_free(pm8001_ha, tag);
return rc;
}
/**
* pm8001_chip_init - the main init function that initialize whole PM8001 chip.
* @pm8001_ha: our hba card information
*/
static int pm80xx_chip_init(struct pm8001_hba_info *pm8001_ha)
{
int ret;
u8 i = 0;
/* check the firmware status */
if (-1 == check_fw_ready(pm8001_ha)) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Firmware is not ready!\n"));
return -EBUSY;
}
/* Initialize the controller fatal error flag */
pm8001_ha->controller_fatal_error = false;
/* Initialize pci space address eg: mpi offset */
init_pci_device_addresses(pm8001_ha);
init_default_table_values(pm8001_ha);
read_main_config_table(pm8001_ha);
read_general_status_table(pm8001_ha);
read_inbnd_queue_table(pm8001_ha);
read_outbnd_queue_table(pm8001_ha);
read_phy_attr_table(pm8001_ha);
/* update main config table ,inbound table and outbound table */
update_main_config_table(pm8001_ha);
for (i = 0; i < PM8001_MAX_SPCV_INB_NUM; i++)
update_inbnd_queue_table(pm8001_ha, i);
for (i = 0; i < PM8001_MAX_SPCV_OUTB_NUM; i++)
update_outbnd_queue_table(pm8001_ha, i);
/* notify firmware update finished and check initialization status */
if (0 == mpi_init_check(pm8001_ha)) {
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("MPI initialize successful!\n"));
} else
return -EBUSY;
/* send SAS protocol timer configuration page to FW */
ret = pm80xx_set_sas_protocol_timer_config(pm8001_ha);
/* Check for encryption */
if (pm8001_ha->chip->encrypt) {
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("Checking for encryption\n"));
ret = pm80xx_get_encrypt_info(pm8001_ha);
if (ret == -1) {
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("Encryption error !!\n"));
if (pm8001_ha->encrypt_info.status == 0x81) {
PM8001_INIT_DBG(pm8001_ha, pm8001_printk(
"Encryption enabled with error."
"Saving encryption key to flash\n"));
pm80xx_encrypt_update(pm8001_ha);
}
}
}
return 0;
}
static int mpi_uninit_check(struct pm8001_hba_info *pm8001_ha)
{
u32 max_wait_count;
u32 value;
u32 gst_len_mpistate;
init_pci_device_addresses(pm8001_ha);
/* Write bit1=1 to Inbound DoorBell Register to tell the SPC FW the
table is stop */
pm8001_cw32(pm8001_ha, 0, MSGU_IBDB_SET, SPCv_MSGU_CFG_TABLE_RESET);
/* wait until Inbound DoorBell Clear Register toggled */
if (IS_SPCV_12G(pm8001_ha->pdev)) {
max_wait_count = 4 * 1000 * 1000;/* 4 sec */
} else {
max_wait_count = 2 * 1000 * 1000;/* 2 sec */
}
do {
udelay(1);
value = pm8001_cr32(pm8001_ha, 0, MSGU_IBDB_SET);
value &= SPCv_MSGU_CFG_TABLE_RESET;
} while ((value != 0) && (--max_wait_count));
if (!max_wait_count) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("TIMEOUT:IBDB value/=%x\n", value));
return -1;
}
/* check the MPI-State for termination in progress */
/* wait until Inbound DoorBell Clear Register toggled */
max_wait_count = 2 * 1000 * 1000; /* 2 sec for spcv/ve */
do {
udelay(1);
gst_len_mpistate =
pm8001_mr32(pm8001_ha->general_stat_tbl_addr,
GST_GSTLEN_MPIS_OFFSET);
if (GST_MPI_STATE_UNINIT ==
(gst_len_mpistate & GST_MPI_STATE_MASK))
break;
} while (--max_wait_count);
if (!max_wait_count) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk(" TIME OUT MPI State = 0x%x\n",
gst_len_mpistate & GST_MPI_STATE_MASK));
return -1;
}
return 0;
}
/**
* pm8001_chip_soft_rst - soft reset the PM8001 chip, so that the clear all
* the FW register status to the originated status.
* @pm8001_ha: our hba card information
*/
static int
pm80xx_chip_soft_rst(struct pm8001_hba_info *pm8001_ha)
{
u32 regval;
u32 bootloader_state;
u32 ibutton0, ibutton1;
/* Process MPI table uninitialization only if FW is ready */
if (!pm8001_ha->controller_fatal_error) {
/* Check if MPI is in ready state to reset */
if (mpi_uninit_check(pm8001_ha) != 0) {
u32 r0 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0);
u32 r1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
u32 r2 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2);
u32 r3 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_3);
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk(
"MPI state is not ready scratch: %x:%x:%x:%x\n",
r0, r1, r2, r3));
/* if things aren't ready but the bootloader is ok then
* try the reset anyway.
*/
if (r1 & SCRATCH_PAD1_BOOTSTATE_MASK)
return -1;
}
}
/* checked for reset register normal state; 0x0 */
regval = pm8001_cr32(pm8001_ha, 0, SPC_REG_SOFT_RESET);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("reset register before write : 0x%x\n", regval));
pm8001_cw32(pm8001_ha, 0, SPC_REG_SOFT_RESET, SPCv_NORMAL_RESET_VALUE);
msleep(500);
regval = pm8001_cr32(pm8001_ha, 0, SPC_REG_SOFT_RESET);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("reset register after write 0x%x\n", regval));
if ((regval & SPCv_SOFT_RESET_READ_MASK) ==
SPCv_SOFT_RESET_NORMAL_RESET_OCCURED) {
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" soft reset successful [regval: 0x%x]\n",
regval));
} else {
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" soft reset failed [regval: 0x%x]\n",
regval));
/* check bootloader is successfully executed or in HDA mode */
bootloader_state =
pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1) &
SCRATCH_PAD1_BOOTSTATE_MASK;
if (bootloader_state == SCRATCH_PAD1_BOOTSTATE_HDA_SEEPROM) {
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"Bootloader state - HDA mode SEEPROM\n"));
} else if (bootloader_state ==
SCRATCH_PAD1_BOOTSTATE_HDA_BOOTSTRAP) {
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"Bootloader state - HDA mode Bootstrap Pin\n"));
} else if (bootloader_state ==
SCRATCH_PAD1_BOOTSTATE_HDA_SOFTRESET) {
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"Bootloader state - HDA mode soft reset\n"));
} else if (bootloader_state ==
SCRATCH_PAD1_BOOTSTATE_CRIT_ERROR) {
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"Bootloader state-HDA mode critical error\n"));
}
return -EBUSY;
}
/* check the firmware status after reset */
if (-1 == check_fw_ready(pm8001_ha)) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Firmware is not ready!\n"));
/* check iButton feature support for motherboard controller */
if (pm8001_ha->pdev->subsystem_vendor !=
PCI_VENDOR_ID_ADAPTEC2 &&
pm8001_ha->pdev->subsystem_vendor !=
PCI_VENDOR_ID_ATTO &&
pm8001_ha->pdev->subsystem_vendor != 0) {
ibutton0 = pm8001_cr32(pm8001_ha, 0,
MSGU_HOST_SCRATCH_PAD_6);
ibutton1 = pm8001_cr32(pm8001_ha, 0,
MSGU_HOST_SCRATCH_PAD_7);
if (!ibutton0 && !ibutton1) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("iButton Feature is"
" not Available!!!\n"));
return -EBUSY;
}
if (ibutton0 == 0xdeadbeef && ibutton1 == 0xdeadbeef) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("CRC Check for iButton"
" Feature Failed!!!\n"));
return -EBUSY;
}
}
}
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("SPCv soft reset Complete\n"));
return 0;
}
static void pm80xx_hw_chip_rst(struct pm8001_hba_info *pm8001_ha)
{
u32 i;
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("chip reset start\n"));
/* do SPCv chip reset. */
pm8001_cw32(pm8001_ha, 0, SPC_REG_SOFT_RESET, 0x11);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("SPC soft reset Complete\n"));
/* Check this ..whether delay is required or no */
/* delay 10 usec */
udelay(10);
/* wait for 20 msec until the firmware gets reloaded */
i = 20;
do {
mdelay(1);
} while ((--i) != 0);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("chip reset finished\n"));
}
/**
* pm8001_chip_interrupt_enable - enable PM8001 chip interrupt
* @pm8001_ha: our hba card information
*/
static void
pm80xx_chip_intx_interrupt_enable(struct pm8001_hba_info *pm8001_ha)
{
pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, ODMR_CLEAR_ALL);
pm8001_cw32(pm8001_ha, 0, MSGU_ODCR, ODCR_CLEAR_ALL);
}
/**
* pm8001_chip_intx_interrupt_disable- disable PM8001 chip interrupt
* @pm8001_ha: our hba card information
*/
static void
pm80xx_chip_intx_interrupt_disable(struct pm8001_hba_info *pm8001_ha)
{
pm8001_cw32(pm8001_ha, 0, MSGU_ODMR_CLR, ODMR_MASK_ALL);
}
/**
* pm8001_chip_interrupt_enable - enable PM8001 chip interrupt
* @pm8001_ha: our hba card information
*/
static void
pm80xx_chip_interrupt_enable(struct pm8001_hba_info *pm8001_ha, u8 vec)
{
#ifdef PM8001_USE_MSIX
u32 mask;
mask = (u32)(1 << vec);
pm8001_cw32(pm8001_ha, 0, MSGU_ODMR_CLR, (u32)(mask & 0xFFFFFFFF));
return;
#endif
pm80xx_chip_intx_interrupt_enable(pm8001_ha);
}
/**
* pm8001_chip_interrupt_disable- disable PM8001 chip interrupt
* @pm8001_ha: our hba card information
*/
static void
pm80xx_chip_interrupt_disable(struct pm8001_hba_info *pm8001_ha, u8 vec)
{
#ifdef PM8001_USE_MSIX
u32 mask;
if (vec == 0xFF)
mask = 0xFFFFFFFF;
else
mask = (u32)(1 << vec);
pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, (u32)(mask & 0xFFFFFFFF));
return;
#endif
pm80xx_chip_intx_interrupt_disable(pm8001_ha);
}
static void pm80xx_send_abort_all(struct pm8001_hba_info *pm8001_ha,
struct pm8001_device *pm8001_ha_dev)
{
int res;
u32 ccb_tag;
struct pm8001_ccb_info *ccb;
struct sas_task *task = NULL;
struct task_abort_req task_abort;
struct inbound_queue_table *circularQ;
u32 opc = OPC_INB_SATA_ABORT;
int ret;
if (!pm8001_ha_dev) {
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("dev is null\n"));
return;
}
task = sas_alloc_slow_task(GFP_ATOMIC);
if (!task) {
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("cannot "
"allocate task\n"));
return;
}
task->task_done = pm8001_task_done;
res = pm8001_tag_alloc(pm8001_ha, &ccb_tag);
if (res) {
sas_free_task(task);
return;
}
ccb = &pm8001_ha->ccb_info[ccb_tag];
ccb->device = pm8001_ha_dev;
ccb->ccb_tag = ccb_tag;
ccb->task = task;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
memset(&task_abort, 0, sizeof(task_abort));
task_abort.abort_all = cpu_to_le32(1);
task_abort.device_id = cpu_to_le32(pm8001_ha_dev->device_id);
task_abort.tag = cpu_to_le32(ccb_tag);
ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &task_abort,
sizeof(task_abort), 0);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Executing abort task end\n"));
if (ret) {
sas_free_task(task);
pm8001_tag_free(pm8001_ha, ccb_tag);
}
}
static void pm80xx_send_read_log(struct pm8001_hba_info *pm8001_ha,
struct pm8001_device *pm8001_ha_dev)
{
struct sata_start_req sata_cmd;
int res;
u32 ccb_tag;
struct pm8001_ccb_info *ccb;
struct sas_task *task = NULL;
struct host_to_dev_fis fis;
struct domain_device *dev;
struct inbound_queue_table *circularQ;
u32 opc = OPC_INB_SATA_HOST_OPSTART;
task = sas_alloc_slow_task(GFP_ATOMIC);
if (!task) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("cannot allocate task !!!\n"));
return;
}
task->task_done = pm8001_task_done;
res = pm8001_tag_alloc(pm8001_ha, &ccb_tag);
if (res) {
sas_free_task(task);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("cannot allocate tag !!!\n"));
return;
}
/* allocate domain device by ourselves as libsas
* is not going to provide any
*/
dev = kzalloc(sizeof(struct domain_device), GFP_ATOMIC);
if (!dev) {
sas_free_task(task);
pm8001_tag_free(pm8001_ha, ccb_tag);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Domain device cannot be allocated\n"));
return;
}
task->dev = dev;
task->dev->lldd_dev = pm8001_ha_dev;
ccb = &pm8001_ha->ccb_info[ccb_tag];
ccb->device = pm8001_ha_dev;
ccb->ccb_tag = ccb_tag;
ccb->task = task;
ccb->n_elem = 0;
pm8001_ha_dev->id |= NCQ_READ_LOG_FLAG;
pm8001_ha_dev->id |= NCQ_2ND_RLE_FLAG;
memset(&sata_cmd, 0, sizeof(sata_cmd));
circularQ = &pm8001_ha->inbnd_q_tbl[0];
/* construct read log FIS */
memset(&fis, 0, sizeof(struct host_to_dev_fis));
fis.fis_type = 0x27;
fis.flags = 0x80;
fis.command = ATA_CMD_READ_LOG_EXT;
fis.lbal = 0x10;
fis.sector_count = 0x1;
sata_cmd.tag = cpu_to_le32(ccb_tag);
sata_cmd.device_id = cpu_to_le32(pm8001_ha_dev->device_id);
sata_cmd.ncqtag_atap_dir_m_dad |= ((0x1 << 7) | (0x5 << 9));
memcpy(&sata_cmd.sata_fis, &fis, sizeof(struct host_to_dev_fis));
res = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &sata_cmd,
sizeof(sata_cmd), 0);
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("Executing read log end\n"));
if (res) {
sas_free_task(task);
pm8001_tag_free(pm8001_ha, ccb_tag);
kfree(dev);
}
}
/**
* mpi_ssp_completion- process the event that FW response to the SSP request.
* @pm8001_ha: our hba card information
* @piomb: the message contents of this outbound message.
*
* When FW has completed a ssp request for example a IO request, after it has
* filled the SG data with the data, it will trigger this event represent
* that he has finished the job,please check the coresponding buffer.
* So we will tell the caller who maybe waiting the result to tell upper layer
* that the task has been finished.
*/
static void
mpi_ssp_completion(struct pm8001_hba_info *pm8001_ha , void *piomb)
{
struct sas_task *t;
struct pm8001_ccb_info *ccb;
unsigned long flags;
u32 status;
u32 param;
u32 tag;
struct ssp_completion_resp *psspPayload;
struct task_status_struct *ts;
struct ssp_response_iu *iu;
struct pm8001_device *pm8001_dev;
psspPayload = (struct ssp_completion_resp *)(piomb + 4);
status = le32_to_cpu(psspPayload->status);
tag = le32_to_cpu(psspPayload->tag);
ccb = &pm8001_ha->ccb_info[tag];
if ((status == IO_ABORTED) && ccb->open_retry) {
/* Being completed by another */
ccb->open_retry = 0;
return;
}
pm8001_dev = ccb->device;
param = le32_to_cpu(psspPayload->param);
t = ccb->task;
if (status && status != IO_UNDERFLOW)
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("sas IO status 0x%x\n", status));
if (unlikely(!t || !t->lldd_task || !t->dev))
return;
ts = &t->task_status;
PM8001_DEV_DBG(pm8001_ha, pm8001_printk(
"tag::0x%x, status::0x%x task::0x%p\n", tag, status, t));
/* Print sas address of IO failed device */
if ((status != IO_SUCCESS) && (status != IO_OVERFLOW) &&
(status != IO_UNDERFLOW))
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("SAS Address of IO Failure Drive"
":%016llx", SAS_ADDR(t->dev->sas_addr)));
switch (status) {
case IO_SUCCESS:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_SUCCESS ,param = 0x%x\n",
param));
if (param == 0) {
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_GOOD;
} else {
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_PROTO_RESPONSE;
ts->residual = param;
iu = &psspPayload->ssp_resp_iu;
sas_ssp_task_response(pm8001_ha->dev, t, iu);
}
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_ABORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_ABORTED IOMB Tag\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_ABORTED_TASK;
break;
case IO_UNDERFLOW:
/* SSP Completion with error */
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_UNDERFLOW ,param = 0x%x\n",
param));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_UNDERRUN;
ts->residual = param;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_NO_DEVICE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_NO_DEVICE\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_PHY_DOWN;
break;
case IO_XFER_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
/* Force the midlayer to retry */
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_XFER_ERROR_PHY_NOT_READY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_XFER_ERROR_INVALID_SSP_RSP_FRAME:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_INVALID_SSP_RSP_FRAME\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_EPROTO;
break;
case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
break;
case IO_OPEN_CNX_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
case IO_XFER_OPEN_RETRY_BACKOFF_THRESHOLD_REACHED:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_TMO:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_NO_DEST:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_COLLIDE:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_PATHWAY_BLOCKED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
if (!t->uldd_task)
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
break;
case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_BAD_DEST;
break;
case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_CONN_RATE;
break;
case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
break;
case IO_XFER_ERROR_NAK_RECEIVED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_XFER_ERROR_ACK_NAK_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_NAK_R_ERR;
break;
case IO_XFER_ERROR_DMA:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_DMA\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
case IO_XFER_OPEN_RETRY_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_XFER_ERROR_OFFSET_MISMATCH:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
case IO_PORT_IN_RESET:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_PORT_IN_RESET\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
case IO_DS_NON_OPERATIONAL:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_DS_NON_OPERATIONAL\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
if (!t->uldd_task)
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_DS_NON_OPERATIONAL);
break;
case IO_DS_IN_RECOVERY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_DS_IN_RECOVERY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
case IO_TM_TAG_NOT_FOUND:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_TM_TAG_NOT_FOUND\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
case IO_SSP_EXT_IU_ZERO_LEN_ERROR:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_SSP_EXT_IU_ZERO_LEN_ERROR\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
default:
PM8001_DEVIO_DBG(pm8001_ha,
pm8001_printk("Unknown status 0x%x\n", status));
/* not allowed case. Therefore, return failed status */
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
break;
}
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("scsi_status = 0x%x\n ",
psspPayload->ssp_resp_iu.status));
spin_lock_irqsave(&t->task_state_lock, flags);
t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
t->task_state_flags |= SAS_TASK_STATE_DONE;
if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk(
"task 0x%p done with io_status 0x%x resp 0x%x "
"stat 0x%x but aborted by upper layer!\n",
t, status, ts->resp, ts->stat));
if (t->slow_task)
complete(&t->slow_task->completion);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
} else {
spin_unlock_irqrestore(&t->task_state_lock, flags);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/* in order to force CPU ordering */
t->task_done(t);
}
}
/*See the comments for mpi_ssp_completion */
static void mpi_ssp_event(struct pm8001_hba_info *pm8001_ha , void *piomb)
{
struct sas_task *t;
unsigned long flags;
struct task_status_struct *ts;
struct pm8001_ccb_info *ccb;
struct pm8001_device *pm8001_dev;
struct ssp_event_resp *psspPayload =
(struct ssp_event_resp *)(piomb + 4);
u32 event = le32_to_cpu(psspPayload->event);
u32 tag = le32_to_cpu(psspPayload->tag);
u32 port_id = le32_to_cpu(psspPayload->port_id);
ccb = &pm8001_ha->ccb_info[tag];
t = ccb->task;
pm8001_dev = ccb->device;
if (event)
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("sas IO status 0x%x\n", event));
if (unlikely(!t || !t->lldd_task || !t->dev))
return;
ts = &t->task_status;
PM8001_IOERR_DBG(pm8001_ha,
pm8001_printk("port_id:0x%x, tag:0x%x, event:0x%x\n",
port_id, tag, event));
switch (event) {
case IO_OVERFLOW:
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n");)
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
ts->residual = 0;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_XFER_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_BREAK\n"));
pm8001_handle_event(pm8001_ha, t, IO_XFER_ERROR_BREAK);
return;
case IO_XFER_ERROR_PHY_NOT_READY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_EPROTO;
break;
case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
break;
case IO_OPEN_CNX_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
case IO_XFER_OPEN_RETRY_BACKOFF_THRESHOLD_REACHED:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_TMO:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_NO_DEST:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_COLLIDE:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_PATHWAY_BLOCKED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
if (!t->uldd_task)
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
break;
case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_BAD_DEST;
break;
case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_CONN_RATE;
break;
case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
break;
case IO_XFER_ERROR_NAK_RECEIVED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_XFER_ERROR_ACK_NAK_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_NAK_R_ERR;
break;
case IO_XFER_OPEN_RETRY_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
pm8001_handle_event(pm8001_ha, t, IO_XFER_OPEN_RETRY_TIMEOUT);
return;
case IO_XFER_ERROR_UNEXPECTED_PHASE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_UNEXPECTED_PHASE\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
case IO_XFER_ERROR_XFER_RDY_OVERRUN:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_XFER_RDY_OVERRUN\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
case IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
case IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
case IO_XFER_ERROR_OFFSET_MISMATCH:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
case IO_XFER_ERROR_XFER_ZERO_DATA_LEN:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_XFER_ZERO_DATA_LEN\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
case IO_XFER_ERROR_INTERNAL_CRC_ERROR:
PM8001_IOERR_DBG(pm8001_ha,
pm8001_printk("IO_XFR_ERROR_INTERNAL_CRC_ERROR\n"));
/* TBC: used default set values */
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
case IO_XFER_CMD_FRAME_ISSUED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_CMD_FRAME_ISSUED\n"));
return;
default:
PM8001_DEVIO_DBG(pm8001_ha,
pm8001_printk("Unknown status 0x%x\n", event));
/* not allowed case. Therefore, return failed status */
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
break;
}
spin_lock_irqsave(&t->task_state_lock, flags);
t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
t->task_state_flags |= SAS_TASK_STATE_DONE;
if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk(
"task 0x%p done with event 0x%x resp 0x%x "
"stat 0x%x but aborted by upper layer!\n",
t, event, ts->resp, ts->stat));
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
} else {
spin_unlock_irqrestore(&t->task_state_lock, flags);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/* in order to force CPU ordering */
t->task_done(t);
}
}
/*See the comments for mpi_ssp_completion */
static void
mpi_sata_completion(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct sas_task *t;
struct pm8001_ccb_info *ccb;
u32 param;
u32 status;
u32 tag;
int i, j;
u8 sata_addr_low[4];
u32 temp_sata_addr_low, temp_sata_addr_hi;
u8 sata_addr_hi[4];
struct sata_completion_resp *psataPayload;
struct task_status_struct *ts;
struct ata_task_resp *resp ;
u32 *sata_resp;
struct pm8001_device *pm8001_dev;
unsigned long flags;
psataPayload = (struct sata_completion_resp *)(piomb + 4);
status = le32_to_cpu(psataPayload->status);
tag = le32_to_cpu(psataPayload->tag);
if (!tag) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("tag null\n"));
return;
}
ccb = &pm8001_ha->ccb_info[tag];
param = le32_to_cpu(psataPayload->param);
if (ccb) {
t = ccb->task;
pm8001_dev = ccb->device;
} else {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("ccb null\n"));
return;
}
if (t) {
if (t->dev && (t->dev->lldd_dev))
pm8001_dev = t->dev->lldd_dev;
} else {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("task null\n"));
return;
}
if ((pm8001_dev && !(pm8001_dev->id & NCQ_READ_LOG_FLAG))
&& unlikely(!t || !t->lldd_task || !t->dev)) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("task or dev null\n"));
return;
}
ts = &t->task_status;
if (!ts) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("ts null\n"));
return;
}
if (unlikely(status))
PM8001_IOERR_DBG(pm8001_ha, pm8001_printk(
"status:0x%x, tag:0x%x, task::0x%p\n",
status, tag, t));
/* Print sas address of IO failed device */
if ((status != IO_SUCCESS) && (status != IO_OVERFLOW) &&
(status != IO_UNDERFLOW)) {
if (!((t->dev->parent) &&
(dev_is_expander(t->dev->parent->dev_type)))) {
for (i = 0 , j = 4; i <= 3 && j <= 7; i++ , j++)
sata_addr_low[i] = pm8001_ha->sas_addr[j];
for (i = 0 , j = 0; i <= 3 && j <= 3; i++ , j++)
sata_addr_hi[i] = pm8001_ha->sas_addr[j];
memcpy(&temp_sata_addr_low, sata_addr_low,
sizeof(sata_addr_low));
memcpy(&temp_sata_addr_hi, sata_addr_hi,
sizeof(sata_addr_hi));
temp_sata_addr_hi = (((temp_sata_addr_hi >> 24) & 0xff)
|((temp_sata_addr_hi << 8) &
0xff0000) |
((temp_sata_addr_hi >> 8)
& 0xff00) |
((temp_sata_addr_hi << 24) &
0xff000000));
temp_sata_addr_low = ((((temp_sata_addr_low >> 24)
& 0xff) |
((temp_sata_addr_low << 8)
& 0xff0000) |
((temp_sata_addr_low >> 8)
& 0xff00) |
((temp_sata_addr_low << 24)
& 0xff000000)) +
pm8001_dev->attached_phy +
0x10);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("SAS Address of IO Failure Drive:"
"%08x%08x", temp_sata_addr_hi,
temp_sata_addr_low));
} else {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("SAS Address of IO Failure Drive:"
"%016llx", SAS_ADDR(t->dev->sas_addr)));
}
}
switch (status) {
case IO_SUCCESS:
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n"));
if (param == 0) {
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_GOOD;
/* check if response is for SEND READ LOG */
if (pm8001_dev &&
(pm8001_dev->id & NCQ_READ_LOG_FLAG)) {
/* set new bit for abort_all */
pm8001_dev->id |= NCQ_ABORT_ALL_FLAG;
/* clear bit for read log */
pm8001_dev->id = pm8001_dev->id & 0x7FFFFFFF;
pm80xx_send_abort_all(pm8001_ha, pm8001_dev);
/* Free the tag */
pm8001_tag_free(pm8001_ha, tag);
sas_free_task(t);
return;
}
} else {
u8 len;
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_PROTO_RESPONSE;
ts->residual = param;
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("SAS_PROTO_RESPONSE len = %d\n",
param));
sata_resp = &psataPayload->sata_resp[0];
resp = (struct ata_task_resp *)ts->buf;
if (t->ata_task.dma_xfer == 0 &&
t->data_dir == DMA_FROM_DEVICE) {
len = sizeof(struct pio_setup_fis);
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("PIO read len = %d\n", len));
} else if (t->ata_task.use_ncq) {
len = sizeof(struct set_dev_bits_fis);
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("FPDMA len = %d\n", len));
} else {
len = sizeof(struct dev_to_host_fis);
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("other len = %d\n", len));
}
if (SAS_STATUS_BUF_SIZE >= sizeof(*resp)) {
resp->frame_len = len;
memcpy(&resp->ending_fis[0], sata_resp, len);
ts->buf_valid_size = sizeof(*resp);
} else
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("response too large\n"));
}
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_ABORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_ABORTED IOMB Tag\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_ABORTED_TASK;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
/* following cases are to do cases */
case IO_UNDERFLOW:
/* SATA Completion with error */
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_UNDERFLOW param = %d\n", param));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_UNDERRUN;
ts->residual = param;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_NO_DEVICE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_NO_DEVICE\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_PHY_DOWN;
break;
case IO_XFER_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_INTERRUPTED;
break;
case IO_XFER_ERROR_PHY_NOT_READY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_EPROTO;
break;
case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
break;
case IO_OPEN_CNX_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_CONT0;
break;
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
case IO_XFER_OPEN_RETRY_BACKOFF_THRESHOLD_REACHED:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_TMO:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_NO_DEST:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_COLLIDE:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_PATHWAY_BLOCKED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
if (!t->uldd_task) {
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_QUEUE_FULL;
pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
return;
}
break;
case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_BAD_DEST;
if (!t->uldd_task) {
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_QUEUE_FULL;
pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
return;
}
break;
case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_CONN_RATE;
break;
case IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY:
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
if (!t->uldd_task) {
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY);
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_QUEUE_FULL;
pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
return;
}
break;
case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
break;
case IO_XFER_ERROR_NAK_RECEIVED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_NAK_R_ERR;
break;
case IO_XFER_ERROR_ACK_NAK_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_NAK_R_ERR;
break;
case IO_XFER_ERROR_DMA:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_DMA\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_ABORTED_TASK;
break;
case IO_XFER_ERROR_SATA_LINK_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_SATA_LINK_TIMEOUT\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_DEV_NO_RESPONSE;
break;
case IO_XFER_ERROR_REJECTED_NCQ_MODE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_REJECTED_NCQ_MODE\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_UNDERRUN;
break;
case IO_XFER_OPEN_RETRY_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_PORT_IN_RESET:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_PORT_IN_RESET\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
break;
case IO_DS_NON_OPERATIONAL:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_DS_NON_OPERATIONAL\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
if (!t->uldd_task) {
pm8001_handle_event(pm8001_ha, pm8001_dev,
IO_DS_NON_OPERATIONAL);
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_QUEUE_FULL;
pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
return;
}
break;
case IO_DS_IN_RECOVERY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_DS_IN_RECOVERY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
break;
case IO_DS_IN_ERROR:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_DS_IN_ERROR\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
if (!t->uldd_task) {
pm8001_handle_event(pm8001_ha, pm8001_dev,
IO_DS_IN_ERROR);
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_QUEUE_FULL;
pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
return;
}
break;
case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
default:
PM8001_DEVIO_DBG(pm8001_ha,
pm8001_printk("Unknown status 0x%x\n", status));
/* not allowed case. Therefore, return failed status */
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
break;
}
spin_lock_irqsave(&t->task_state_lock, flags);
t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
t->task_state_flags |= SAS_TASK_STATE_DONE;
if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("task 0x%p done with io_status 0x%x"
" resp 0x%x stat 0x%x but aborted by upper layer!\n",
t, status, ts->resp, ts->stat));
if (t->slow_task)
complete(&t->slow_task->completion);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
} else {
spin_unlock_irqrestore(&t->task_state_lock, flags);
pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
}
}
/*See the comments for mpi_ssp_completion */
static void mpi_sata_event(struct pm8001_hba_info *pm8001_ha , void *piomb)
{
struct sas_task *t;
struct task_status_struct *ts;
struct pm8001_ccb_info *ccb;
struct pm8001_device *pm8001_dev;
struct sata_event_resp *psataPayload =
(struct sata_event_resp *)(piomb + 4);
u32 event = le32_to_cpu(psataPayload->event);
u32 tag = le32_to_cpu(psataPayload->tag);
u32 port_id = le32_to_cpu(psataPayload->port_id);
u32 dev_id = le32_to_cpu(psataPayload->device_id);
unsigned long flags;
ccb = &pm8001_ha->ccb_info[tag];
if (ccb) {
t = ccb->task;
pm8001_dev = ccb->device;
} else {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("No CCB !!!. returning\n"));
return;
}
if (event)
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("SATA EVENT 0x%x\n", event));
/* Check if this is NCQ error */
if (event == IO_XFER_ERROR_ABORTED_NCQ_MODE) {
/* find device using device id */
pm8001_dev = pm8001_find_dev(pm8001_ha, dev_id);
/* send read log extension */
if (pm8001_dev)
pm80xx_send_read_log(pm8001_ha, pm8001_dev);
return;
}
if (unlikely(!t || !t->lldd_task || !t->dev)) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("task or dev null\n"));
return;
}
ts = &t->task_status;
PM8001_IOERR_DBG(pm8001_ha,
pm8001_printk("port_id:0x%x, tag:0x%x, event:0x%x\n",
port_id, tag, event));
switch (event) {
case IO_OVERFLOW:
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
ts->residual = 0;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_XFER_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_INTERRUPTED;
break;
case IO_XFER_ERROR_PHY_NOT_READY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_EPROTO;
break;
case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
break;
case IO_OPEN_CNX_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_CONT0;
break;
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
case IO_XFER_OPEN_RETRY_BACKOFF_THRESHOLD_REACHED:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_TMO:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_NO_DEST:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_COLLIDE:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_PATHWAY_BLOCKED:
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_DEV_NO_RESPONSE;
if (!t->uldd_task) {
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_QUEUE_FULL;
pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
return;
}
break;
case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
ts->resp = SAS_TASK_UNDELIVERED;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_BAD_DEST;
break;
case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_CONN_RATE;
break;
case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
break;
case IO_XFER_ERROR_NAK_RECEIVED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_NAK_R_ERR;
break;
case IO_XFER_ERROR_PEER_ABORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_PEER_ABORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_NAK_R_ERR;
break;
case IO_XFER_ERROR_REJECTED_NCQ_MODE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_REJECTED_NCQ_MODE\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_UNDERRUN;
break;
case IO_XFER_OPEN_RETRY_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_ERROR_UNEXPECTED_PHASE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_UNEXPECTED_PHASE\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_ERROR_XFER_RDY_OVERRUN:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_XFER_RDY_OVERRUN\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_ERROR_OFFSET_MISMATCH:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_ERROR_XFER_ZERO_DATA_LEN:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_XFER_ZERO_DATA_LEN\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_CMD_FRAME_ISSUED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_CMD_FRAME_ISSUED\n"));
break;
case IO_XFER_PIO_SETUP_ERROR:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_PIO_SETUP_ERROR\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_ERROR_INTERNAL_CRC_ERROR:
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("IO_XFR_ERROR_INTERNAL_CRC_ERROR\n"));
/* TBC: used default set values */
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
case IO_XFER_DMA_ACTIVATE_TIMEOUT:
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("IO_XFR_DMA_ACTIVATE_TIMEOUT\n"));
/* TBC: used default set values */
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
default:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("Unknown status 0x%x\n", event));
/* not allowed case. Therefore, return failed status */
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_TO;
break;
}
spin_lock_irqsave(&t->task_state_lock, flags);
t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
t->task_state_flags |= SAS_TASK_STATE_DONE;
if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("task 0x%p done with io_status 0x%x"
" resp 0x%x stat 0x%x but aborted by upper layer!\n",
t, event, ts->resp, ts->stat));
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
} else {
spin_unlock_irqrestore(&t->task_state_lock, flags);
pm8001_ccb_task_free_done(pm8001_ha, t, ccb, tag);
}
}
/*See the comments for mpi_ssp_completion */
static void
mpi_smp_completion(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
u32 param, i;
struct sas_task *t;
struct pm8001_ccb_info *ccb;
unsigned long flags;
u32 status;
u32 tag;
struct smp_completion_resp *psmpPayload;
struct task_status_struct *ts;
struct pm8001_device *pm8001_dev;
char *pdma_respaddr = NULL;
psmpPayload = (struct smp_completion_resp *)(piomb + 4);
status = le32_to_cpu(psmpPayload->status);
tag = le32_to_cpu(psmpPayload->tag);
ccb = &pm8001_ha->ccb_info[tag];
param = le32_to_cpu(psmpPayload->param);
t = ccb->task;
ts = &t->task_status;
pm8001_dev = ccb->device;
if (status)
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("smp IO status 0x%x\n", status));
if (unlikely(!t || !t->lldd_task || !t->dev))
return;
PM8001_DEV_DBG(pm8001_ha,
pm8001_printk("tag::0x%x status::0x%x\n", tag, status));
switch (status) {
case IO_SUCCESS:
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_GOOD;
if (pm8001_dev)
pm8001_dev->running_req--;
if (pm8001_ha->smp_exp_mode == SMP_DIRECT) {
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("DIRECT RESPONSE Length:%d\n",
param));
pdma_respaddr = (char *)(phys_to_virt(cpu_to_le64
((u64)sg_dma_address
(&t->smp_task.smp_resp))));
for (i = 0; i < param; i++) {
*(pdma_respaddr+i) = psmpPayload->_r_a[i];
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"SMP Byte%d DMA data 0x%x psmp 0x%x\n",
i, *(pdma_respaddr+i),
psmpPayload->_r_a[i]));
}
}
break;
case IO_ABORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_ABORTED IOMB\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_ABORTED_TASK;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_OVERFLOW:
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DATA_OVERRUN;
ts->residual = 0;
if (pm8001_dev)
pm8001_dev->running_req--;
break;
case IO_NO_DEVICE:
PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_NO_DEVICE\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_PHY_DOWN;
break;
case IO_ERROR_HW_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_ERROR_HW_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_BUSY;
break;
case IO_XFER_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_BUSY;
break;
case IO_XFER_ERROR_PHY_NOT_READY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_BUSY;
break;
case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
break;
case IO_OPEN_CNX_ERROR_ZONE_VIOLATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
break;
case IO_OPEN_CNX_ERROR_BREAK:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_CONT0;
break;
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS:
case IO_XFER_OPEN_RETRY_BACKOFF_THRESHOLD_REACHED:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_TMO:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_NO_DEST:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_COLLIDE:
case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_PATHWAY_BLOCKED:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_UNKNOWN;
pm8001_handle_event(pm8001_ha,
pm8001_dev,
IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS);
break;
case IO_OPEN_CNX_ERROR_BAD_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_BAD_DEST;
break;
case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED:
PM8001_IO_DBG(pm8001_ha, pm8001_printk(\
"IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_CONN_RATE;
break;
case IO_OPEN_CNX_ERROR_WRONG_DESTINATION:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_WRONG_DEST;
break;
case IO_XFER_ERROR_RX_FRAME:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_ERROR_RX_FRAME\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
break;
case IO_XFER_OPEN_RETRY_TIMEOUT:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_ERROR_INTERNAL_SMP_RESOURCE:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_ERROR_INTERNAL_SMP_RESOURCE\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_QUEUE_FULL;
break;
case IO_PORT_IN_RESET:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_PORT_IN_RESET\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_DS_NON_OPERATIONAL:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_DS_NON_OPERATIONAL\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
break;
case IO_DS_IN_RECOVERY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_DS_IN_RECOVERY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY:
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n"));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_OPEN_REJECT;
ts->open_rej_reason = SAS_OREJ_RSVD_RETRY;
break;
default:
PM8001_DEVIO_DBG(pm8001_ha,
pm8001_printk("Unknown status 0x%x\n", status));
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAS_DEV_NO_RESPONSE;
/* not allowed case. Therefore, return failed status */
break;
}
spin_lock_irqsave(&t->task_state_lock, flags);
t->task_state_flags &= ~SAS_TASK_STATE_PENDING;
t->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
t->task_state_flags |= SAS_TASK_STATE_DONE;
if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) {
spin_unlock_irqrestore(&t->task_state_lock, flags);
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk(
"task 0x%p done with io_status 0x%x resp 0x%x"
"stat 0x%x but aborted by upper layer!\n",
t, status, ts->resp, ts->stat));
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
} else {
spin_unlock_irqrestore(&t->task_state_lock, flags);
pm8001_ccb_task_free(pm8001_ha, t, ccb, tag);
mb();/* in order to force CPU ordering */
t->task_done(t);
}
}
/**
* pm80xx_hw_event_ack_req- For PM8001,some events need to acknowage to FW.
* @pm8001_ha: our hba card information
* @Qnum: the outbound queue message number.
* @SEA: source of event to ack
* @port_id: port id.
* @phyId: phy id.
* @param0: parameter 0.
* @param1: parameter 1.
*/
static void pm80xx_hw_event_ack_req(struct pm8001_hba_info *pm8001_ha,
u32 Qnum, u32 SEA, u32 port_id, u32 phyId, u32 param0, u32 param1)
{
struct hw_event_ack_req payload;
u32 opc = OPC_INB_SAS_HW_EVENT_ACK;
struct inbound_queue_table *circularQ;
memset((u8 *)&payload, 0, sizeof(payload));
circularQ = &pm8001_ha->inbnd_q_tbl[Qnum];
payload.tag = cpu_to_le32(1);
payload.phyid_sea_portid = cpu_to_le32(((SEA & 0xFFFF) << 8) |
((phyId & 0xFF) << 24) | (port_id & 0xFF));
payload.param0 = cpu_to_le32(param0);
payload.param1 = cpu_to_le32(param1);
pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload,
sizeof(payload), 0);
}
static int pm80xx_chip_phy_ctl_req(struct pm8001_hba_info *pm8001_ha,
u32 phyId, u32 phy_op);
static void hw_event_port_recover(struct pm8001_hba_info *pm8001_ha,
void *piomb)
{
struct hw_event_resp *pPayload = (struct hw_event_resp *)(piomb + 4);
u32 phyid_npip_portstate = le32_to_cpu(pPayload->phyid_npip_portstate);
u8 phy_id = (u8)((phyid_npip_portstate & 0xFF0000) >> 16);
u32 lr_status_evt_portid =
le32_to_cpu(pPayload->lr_status_evt_portid);
u8 deviceType = pPayload->sas_identify.dev_type;
u8 link_rate = (u8)((lr_status_evt_portid & 0xF0000000) >> 28);
struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
u8 port_id = (u8)(lr_status_evt_portid & 0x000000FF);
struct pm8001_port *port = &pm8001_ha->port[port_id];
if (deviceType == SAS_END_DEVICE) {
pm80xx_chip_phy_ctl_req(pm8001_ha, phy_id,
PHY_NOTIFY_ENABLE_SPINUP);
}
port->wide_port_phymap |= (1U << phy_id);
pm8001_get_lrate_mode(phy, link_rate);
phy->sas_phy.oob_mode = SAS_OOB_MODE;
phy->phy_state = PHY_STATE_LINK_UP_SPCV;
phy->phy_attached = 1;
}
/**
* hw_event_sas_phy_up -FW tells me a SAS phy up event.
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static void
hw_event_sas_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct hw_event_resp *pPayload =
(struct hw_event_resp *)(piomb + 4);
u32 lr_status_evt_portid =
le32_to_cpu(pPayload->lr_status_evt_portid);
u32 phyid_npip_portstate = le32_to_cpu(pPayload->phyid_npip_portstate);
u8 link_rate =
(u8)((lr_status_evt_portid & 0xF0000000) >> 28);
u8 port_id = (u8)(lr_status_evt_portid & 0x000000FF);
u8 phy_id =
(u8)((phyid_npip_portstate & 0xFF0000) >> 16);
u8 portstate = (u8)(phyid_npip_portstate & 0x0000000F);
struct pm8001_port *port = &pm8001_ha->port[port_id];
struct sas_ha_struct *sas_ha = pm8001_ha->sas;
struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
unsigned long flags;
u8 deviceType = pPayload->sas_identify.dev_type;
port->port_state = portstate;
port->wide_port_phymap |= (1U << phy_id);
phy->phy_state = PHY_STATE_LINK_UP_SPCV;
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"portid:%d; phyid:%d; linkrate:%d; "
"portstate:%x; devicetype:%x\n",
port_id, phy_id, link_rate, portstate, deviceType));
switch (deviceType) {
case SAS_PHY_UNUSED:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("device type no device.\n"));
break;
case SAS_END_DEVICE:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk("end device.\n"));
pm80xx_chip_phy_ctl_req(pm8001_ha, phy_id,
PHY_NOTIFY_ENABLE_SPINUP);
port->port_attached = 1;
pm8001_get_lrate_mode(phy, link_rate);
break;
case SAS_EDGE_EXPANDER_DEVICE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("expander device.\n"));
port->port_attached = 1;
pm8001_get_lrate_mode(phy, link_rate);
break;
case SAS_FANOUT_EXPANDER_DEVICE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("fanout expander device.\n"));
port->port_attached = 1;
pm8001_get_lrate_mode(phy, link_rate);
break;
default:
PM8001_DEVIO_DBG(pm8001_ha,
pm8001_printk("unknown device type(%x)\n", deviceType));
break;
}
phy->phy_type |= PORT_TYPE_SAS;
phy->identify.device_type = deviceType;
phy->phy_attached = 1;
if (phy->identify.device_type == SAS_END_DEVICE)
phy->identify.target_port_protocols = SAS_PROTOCOL_SSP;
else if (phy->identify.device_type != SAS_PHY_UNUSED)
phy->identify.target_port_protocols = SAS_PROTOCOL_SMP;
phy->sas_phy.oob_mode = SAS_OOB_MODE;
sas_ha->notify_phy_event(&phy->sas_phy, PHYE_OOB_DONE);
spin_lock_irqsave(&phy->sas_phy.frame_rcvd_lock, flags);
memcpy(phy->frame_rcvd, &pPayload->sas_identify,
sizeof(struct sas_identify_frame)-4);
phy->frame_rcvd_size = sizeof(struct sas_identify_frame) - 4;
pm8001_get_attached_sas_addr(phy, phy->sas_phy.attached_sas_addr);
spin_unlock_irqrestore(&phy->sas_phy.frame_rcvd_lock, flags);
if (pm8001_ha->flags == PM8001F_RUN_TIME)
msleep(200);/*delay a moment to wait disk to spinup*/
pm8001_bytes_dmaed(pm8001_ha, phy_id);
}
/**
* hw_event_sata_phy_up -FW tells me a SATA phy up event.
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static void
hw_event_sata_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct hw_event_resp *pPayload =
(struct hw_event_resp *)(piomb + 4);
u32 phyid_npip_portstate = le32_to_cpu(pPayload->phyid_npip_portstate);
u32 lr_status_evt_portid =
le32_to_cpu(pPayload->lr_status_evt_portid);
u8 link_rate =
(u8)((lr_status_evt_portid & 0xF0000000) >> 28);
u8 port_id = (u8)(lr_status_evt_portid & 0x000000FF);
u8 phy_id =
(u8)((phyid_npip_portstate & 0xFF0000) >> 16);
u8 portstate = (u8)(phyid_npip_portstate & 0x0000000F);
struct pm8001_port *port = &pm8001_ha->port[port_id];
struct sas_ha_struct *sas_ha = pm8001_ha->sas;
struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
unsigned long flags;
PM8001_DEVIO_DBG(pm8001_ha, pm8001_printk(
"port id %d, phy id %d link_rate %d portstate 0x%x\n",
port_id, phy_id, link_rate, portstate));
port->port_state = portstate;
phy->phy_state = PHY_STATE_LINK_UP_SPCV;
port->port_attached = 1;
pm8001_get_lrate_mode(phy, link_rate);
phy->phy_type |= PORT_TYPE_SATA;
phy->phy_attached = 1;
phy->sas_phy.oob_mode = SATA_OOB_MODE;
sas_ha->notify_phy_event(&phy->sas_phy, PHYE_OOB_DONE);
spin_lock_irqsave(&phy->sas_phy.frame_rcvd_lock, flags);
memcpy(phy->frame_rcvd, ((u8 *)&pPayload->sata_fis - 4),
sizeof(struct dev_to_host_fis));
phy->frame_rcvd_size = sizeof(struct dev_to_host_fis);
phy->identify.target_port_protocols = SAS_PROTOCOL_SATA;
phy->identify.device_type = SAS_SATA_DEV;
pm8001_get_attached_sas_addr(phy, phy->sas_phy.attached_sas_addr);
spin_unlock_irqrestore(&phy->sas_phy.frame_rcvd_lock, flags);
pm8001_bytes_dmaed(pm8001_ha, phy_id);
}
/**
* hw_event_phy_down -we should notify the libsas the phy is down.
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static void
hw_event_phy_down(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct hw_event_resp *pPayload =
(struct hw_event_resp *)(piomb + 4);
u32 lr_status_evt_portid =
le32_to_cpu(pPayload->lr_status_evt_portid);
u8 port_id = (u8)(lr_status_evt_portid & 0x000000FF);
u32 phyid_npip_portstate = le32_to_cpu(pPayload->phyid_npip_portstate);
u8 phy_id =
(u8)((phyid_npip_portstate & 0xFF0000) >> 16);
u8 portstate = (u8)(phyid_npip_portstate & 0x0000000F);
struct pm8001_port *port = &pm8001_ha->port[port_id];
struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
u32 port_sata = (phy->phy_type & PORT_TYPE_SATA);
port->port_state = portstate;
phy->identify.device_type = 0;
phy->phy_attached = 0;
switch (portstate) {
case PORT_VALID:
break;
case PORT_INVALID:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" PortInvalid portID %d\n", port_id));
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" Last phy Down and port invalid\n"));
if (port_sata) {
phy->phy_type = 0;
port->port_attached = 0;
pm80xx_hw_event_ack_req(pm8001_ha, 0, HW_EVENT_PHY_DOWN,
port_id, phy_id, 0, 0);
}
sas_phy_disconnected(&phy->sas_phy);
break;
case PORT_IN_RESET:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" Port In Reset portID %d\n", port_id));
break;
case PORT_NOT_ESTABLISHED:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" Phy Down and PORT_NOT_ESTABLISHED\n"));
port->port_attached = 0;
break;
case PORT_LOSTCOMM:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" Phy Down and PORT_LOSTCOMM\n"));
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" Last phy Down and port invalid\n"));
if (port_sata) {
port->port_attached = 0;
phy->phy_type = 0;
pm80xx_hw_event_ack_req(pm8001_ha, 0, HW_EVENT_PHY_DOWN,
port_id, phy_id, 0, 0);
}
sas_phy_disconnected(&phy->sas_phy);
break;
default:
port->port_attached = 0;
PM8001_DEVIO_DBG(pm8001_ha,
pm8001_printk(" Phy Down and(default) = 0x%x\n",
portstate));
break;
}
if (port_sata && (portstate != PORT_IN_RESET)) {
struct sas_ha_struct *sas_ha = pm8001_ha->sas;
sas_ha->notify_phy_event(&phy->sas_phy, PHYE_LOSS_OF_SIGNAL);
}
}
static int mpi_phy_start_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct phy_start_resp *pPayload =
(struct phy_start_resp *)(piomb + 4);
u32 status =
le32_to_cpu(pPayload->status);
u32 phy_id =
le32_to_cpu(pPayload->phyid);
struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("phy start resp status:0x%x, phyid:0x%x\n",
status, phy_id));
if (status == 0) {
phy->phy_state = PHY_LINK_DOWN;
if (pm8001_ha->flags == PM8001F_RUN_TIME &&
phy->enable_completion != NULL) {
complete(phy->enable_completion);
phy->enable_completion = NULL;
}
}
return 0;
}
/**
* mpi_thermal_hw_event -The hw event has come.
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static int mpi_thermal_hw_event(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct thermal_hw_event *pPayload =
(struct thermal_hw_event *)(piomb + 4);
u32 thermal_event = le32_to_cpu(pPayload->thermal_event);
u32 rht_lht = le32_to_cpu(pPayload->rht_lht);
if (thermal_event & 0x40) {
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"Thermal Event: Local high temperature violated!\n"));
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"Thermal Event: Measured local high temperature %d\n",
((rht_lht & 0xFF00) >> 8)));
}
if (thermal_event & 0x10) {
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"Thermal Event: Remote high temperature violated!\n"));
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"Thermal Event: Measured remote high temperature %d\n",
((rht_lht & 0xFF000000) >> 24)));
}
return 0;
}
/**
* mpi_hw_event -The hw event has come.
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static int mpi_hw_event(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
unsigned long flags, i;
struct hw_event_resp *pPayload =
(struct hw_event_resp *)(piomb + 4);
u32 lr_status_evt_portid =
le32_to_cpu(pPayload->lr_status_evt_portid);
u32 phyid_npip_portstate = le32_to_cpu(pPayload->phyid_npip_portstate);
u8 port_id = (u8)(lr_status_evt_portid & 0x000000FF);
u8 phy_id =
(u8)((phyid_npip_portstate & 0xFF0000) >> 16);
u16 eventType =
(u16)((lr_status_evt_portid & 0x00FFFF00) >> 8);
u8 status =
(u8)((lr_status_evt_portid & 0x0F000000) >> 24);
struct sas_ha_struct *sas_ha = pm8001_ha->sas;
struct pm8001_phy *phy = &pm8001_ha->phy[phy_id];
struct pm8001_port *port = &pm8001_ha->port[port_id];
struct asd_sas_phy *sas_phy = sas_ha->sas_phy[phy_id];
PM8001_DEV_DBG(pm8001_ha,
pm8001_printk("portid:%d phyid:%d event:0x%x status:0x%x\n",
port_id, phy_id, eventType, status));
switch (eventType) {
case HW_EVENT_SAS_PHY_UP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PHY_START_STATUS\n"));
hw_event_sas_phy_up(pm8001_ha, piomb);
break;
case HW_EVENT_SATA_PHY_UP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_SATA_PHY_UP\n"));
hw_event_sata_phy_up(pm8001_ha, piomb);
break;
case HW_EVENT_SATA_SPINUP_HOLD:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_SATA_SPINUP_HOLD\n"));
sas_ha->notify_phy_event(&phy->sas_phy, PHYE_SPINUP_HOLD);
break;
case HW_EVENT_PHY_DOWN:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PHY_DOWN\n"));
hw_event_phy_down(pm8001_ha, piomb);
if (pm8001_ha->reset_in_progress) {
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("Reset in progress\n"));
return 0;
}
phy->phy_attached = 0;
phy->phy_state = PHY_LINK_DISABLE;
break;
case HW_EVENT_PORT_INVALID:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PORT_INVALID\n"));
sas_phy_disconnected(sas_phy);
phy->phy_attached = 0;
sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
break;
/* the broadcast change primitive received, tell the LIBSAS this event
to revalidate the sas domain*/
case HW_EVENT_BROADCAST_CHANGE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_BROADCAST_CHANGE\n"));
pm80xx_hw_event_ack_req(pm8001_ha, 0, HW_EVENT_BROADCAST_CHANGE,
port_id, phy_id, 1, 0);
spin_lock_irqsave(&sas_phy->sas_prim_lock, flags);
sas_phy->sas_prim = HW_EVENT_BROADCAST_CHANGE;
spin_unlock_irqrestore(&sas_phy->sas_prim_lock, flags);
sas_ha->notify_port_event(sas_phy, PORTE_BROADCAST_RCVD);
break;
case HW_EVENT_PHY_ERROR:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PHY_ERROR\n"));
sas_phy_disconnected(&phy->sas_phy);
phy->phy_attached = 0;
sas_ha->notify_phy_event(&phy->sas_phy, PHYE_OOB_ERROR);
break;
case HW_EVENT_BROADCAST_EXP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_BROADCAST_EXP\n"));
spin_lock_irqsave(&sas_phy->sas_prim_lock, flags);
sas_phy->sas_prim = HW_EVENT_BROADCAST_EXP;
spin_unlock_irqrestore(&sas_phy->sas_prim_lock, flags);
sas_ha->notify_port_event(sas_phy, PORTE_BROADCAST_RCVD);
break;
case HW_EVENT_LINK_ERR_INVALID_DWORD:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_LINK_ERR_INVALID_DWORD\n"));
pm80xx_hw_event_ack_req(pm8001_ha, 0,
HW_EVENT_LINK_ERR_INVALID_DWORD, port_id, phy_id, 0, 0);
break;
case HW_EVENT_LINK_ERR_DISPARITY_ERROR:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_LINK_ERR_DISPARITY_ERROR\n"));
pm80xx_hw_event_ack_req(pm8001_ha, 0,
HW_EVENT_LINK_ERR_DISPARITY_ERROR,
port_id, phy_id, 0, 0);
break;
case HW_EVENT_LINK_ERR_CODE_VIOLATION:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_LINK_ERR_CODE_VIOLATION\n"));
pm80xx_hw_event_ack_req(pm8001_ha, 0,
HW_EVENT_LINK_ERR_CODE_VIOLATION,
port_id, phy_id, 0, 0);
break;
case HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH\n"));
pm80xx_hw_event_ack_req(pm8001_ha, 0,
HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH,
port_id, phy_id, 0, 0);
break;
case HW_EVENT_MALFUNCTION:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_MALFUNCTION\n"));
break;
case HW_EVENT_BROADCAST_SES:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_BROADCAST_SES\n"));
spin_lock_irqsave(&sas_phy->sas_prim_lock, flags);
sas_phy->sas_prim = HW_EVENT_BROADCAST_SES;
spin_unlock_irqrestore(&sas_phy->sas_prim_lock, flags);
sas_ha->notify_port_event(sas_phy, PORTE_BROADCAST_RCVD);
break;
case HW_EVENT_INBOUND_CRC_ERROR:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_INBOUND_CRC_ERROR\n"));
pm80xx_hw_event_ack_req(pm8001_ha, 0,
HW_EVENT_INBOUND_CRC_ERROR,
port_id, phy_id, 0, 0);
break;
case HW_EVENT_HARD_RESET_RECEIVED:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_HARD_RESET_RECEIVED\n"));
sas_ha->notify_port_event(sas_phy, PORTE_HARD_RESET);
break;
case HW_EVENT_ID_FRAME_TIMEOUT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_ID_FRAME_TIMEOUT\n"));
sas_phy_disconnected(sas_phy);
phy->phy_attached = 0;
sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
break;
case HW_EVENT_LINK_ERR_PHY_RESET_FAILED:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_LINK_ERR_PHY_RESET_FAILED\n"));
pm80xx_hw_event_ack_req(pm8001_ha, 0,
HW_EVENT_LINK_ERR_PHY_RESET_FAILED,
port_id, phy_id, 0, 0);
sas_phy_disconnected(sas_phy);
phy->phy_attached = 0;
sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
break;
case HW_EVENT_PORT_RESET_TIMER_TMO:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PORT_RESET_TIMER_TMO\n"));
pm80xx_hw_event_ack_req(pm8001_ha, 0, HW_EVENT_PHY_DOWN,
port_id, phy_id, 0, 0);
sas_phy_disconnected(sas_phy);
phy->phy_attached = 0;
sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR);
if (pm8001_ha->phy[phy_id].reset_completion) {
pm8001_ha->phy[phy_id].port_reset_status =
PORT_RESET_TMO;
complete(pm8001_ha->phy[phy_id].reset_completion);
pm8001_ha->phy[phy_id].reset_completion = NULL;
}
break;
case HW_EVENT_PORT_RECOVERY_TIMER_TMO:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PORT_RECOVERY_TIMER_TMO\n"));
pm80xx_hw_event_ack_req(pm8001_ha, 0,
HW_EVENT_PORT_RECOVERY_TIMER_TMO,
port_id, phy_id, 0, 0);
for (i = 0; i < pm8001_ha->chip->n_phy; i++) {
if (port->wide_port_phymap & (1 << i)) {
phy = &pm8001_ha->phy[i];
sas_ha->notify_phy_event(&phy->sas_phy,
PHYE_LOSS_OF_SIGNAL);
port->wide_port_phymap &= ~(1 << i);
}
}
break;
case HW_EVENT_PORT_RECOVER:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PORT_RECOVER\n"));
hw_event_port_recover(pm8001_ha, piomb);
break;
case HW_EVENT_PORT_RESET_COMPLETE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("HW_EVENT_PORT_RESET_COMPLETE\n"));
if (pm8001_ha->phy[phy_id].reset_completion) {
pm8001_ha->phy[phy_id].port_reset_status =
PORT_RESET_SUCCESS;
complete(pm8001_ha->phy[phy_id].reset_completion);
pm8001_ha->phy[phy_id].reset_completion = NULL;
}
break;
case EVENT_BROADCAST_ASYNCH_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("EVENT_BROADCAST_ASYNCH_EVENT\n"));
break;
default:
PM8001_DEVIO_DBG(pm8001_ha,
pm8001_printk("Unknown event type 0x%x\n", eventType));
break;
}
return 0;
}
/**
* mpi_phy_stop_resp - SPCv specific
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static int mpi_phy_stop_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
struct phy_stop_resp *pPayload =
(struct phy_stop_resp *)(piomb + 4);
u32 status =
le32_to_cpu(pPayload->status);
u32 phyid =
le32_to_cpu(pPayload->phyid) & 0xFF;
struct pm8001_phy *phy = &pm8001_ha->phy[phyid];
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("phy:0x%x status:0x%x\n",
phyid, status));
if (status == PHY_STOP_SUCCESS ||
status == PHY_STOP_ERR_DEVICE_ATTACHED)
phy->phy_state = PHY_LINK_DISABLE;
return 0;
}
/**
* mpi_set_controller_config_resp - SPCv specific
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static int mpi_set_controller_config_resp(struct pm8001_hba_info *pm8001_ha,
void *piomb)
{
struct set_ctrl_cfg_resp *pPayload =
(struct set_ctrl_cfg_resp *)(piomb + 4);
u32 status = le32_to_cpu(pPayload->status);
u32 err_qlfr_pgcd = le32_to_cpu(pPayload->err_qlfr_pgcd);
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"SET CONTROLLER RESP: status 0x%x qlfr_pgcd 0x%x\n",
status, err_qlfr_pgcd));
return 0;
}
/**
* mpi_get_controller_config_resp - SPCv specific
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static int mpi_get_controller_config_resp(struct pm8001_hba_info *pm8001_ha,
void *piomb)
{
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" pm80xx_addition_functionality\n"));
return 0;
}
/**
* mpi_get_phy_profile_resp - SPCv specific
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static int mpi_get_phy_profile_resp(struct pm8001_hba_info *pm8001_ha,
void *piomb)
{
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" pm80xx_addition_functionality\n"));
return 0;
}
/**
* mpi_flash_op_ext_resp - SPCv specific
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static int mpi_flash_op_ext_resp(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" pm80xx_addition_functionality\n"));
return 0;
}
/**
* mpi_set_phy_profile_resp - SPCv specific
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static int mpi_set_phy_profile_resp(struct pm8001_hba_info *pm8001_ha,
void *piomb)
{
u32 tag;
u8 page_code;
int rc = 0;
struct set_phy_profile_resp *pPayload =
(struct set_phy_profile_resp *)(piomb + 4);
u32 ppc_phyid = le32_to_cpu(pPayload->ppc_phyid);
u32 status = le32_to_cpu(pPayload->status);
tag = le32_to_cpu(pPayload->tag);
page_code = (u8)((ppc_phyid & 0xFF00) >> 8);
if (status) {
/* status is FAILED */
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("PhyProfile command failed with status "
"0x%08X \n", status));
rc = -1;
} else {
if (page_code != SAS_PHY_ANALOG_SETTINGS_PAGE) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("Invalid page code 0x%X\n",
page_code));
rc = -1;
}
}
pm8001_tag_free(pm8001_ha, tag);
return rc;
}
/**
* mpi_kek_management_resp - SPCv specific
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static int mpi_kek_management_resp(struct pm8001_hba_info *pm8001_ha,
void *piomb)
{
struct kek_mgmt_resp *pPayload = (struct kek_mgmt_resp *)(piomb + 4);
u32 status = le32_to_cpu(pPayload->status);
u32 kidx_new_curr_ksop = le32_to_cpu(pPayload->kidx_new_curr_ksop);
u32 err_qlfr = le32_to_cpu(pPayload->err_qlfr);
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"KEK MGMT RESP. Status 0x%x idx_ksop 0x%x err_qlfr 0x%x\n",
status, kidx_new_curr_ksop, err_qlfr));
return 0;
}
/**
* mpi_dek_management_resp - SPCv specific
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static int mpi_dek_management_resp(struct pm8001_hba_info *pm8001_ha,
void *piomb)
{
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" pm80xx_addition_functionality\n"));
return 0;
}
/**
* ssp_coalesced_comp_resp - SPCv specific
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static int ssp_coalesced_comp_resp(struct pm8001_hba_info *pm8001_ha,
void *piomb)
{
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk(" pm80xx_addition_functionality\n"));
return 0;
}
/**
* process_one_iomb - process one outbound Queue memory block
* @pm8001_ha: our hba card information
* @piomb: IO message buffer
*/
static void process_one_iomb(struct pm8001_hba_info *pm8001_ha, void *piomb)
{
__le32 pHeader = *(__le32 *)piomb;
u32 opc = (u32)((le32_to_cpu(pHeader)) & 0xFFF);
switch (opc) {
case OPC_OUB_ECHO:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk("OPC_OUB_ECHO\n"));
break;
case OPC_OUB_HW_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_HW_EVENT\n"));
mpi_hw_event(pm8001_ha, piomb);
break;
case OPC_OUB_THERM_HW_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_THERMAL_EVENT\n"));
mpi_thermal_hw_event(pm8001_ha, piomb);
break;
case OPC_OUB_SSP_COMP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SSP_COMP\n"));
mpi_ssp_completion(pm8001_ha, piomb);
break;
case OPC_OUB_SMP_COMP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SMP_COMP\n"));
mpi_smp_completion(pm8001_ha, piomb);
break;
case OPC_OUB_LOCAL_PHY_CNTRL:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_LOCAL_PHY_CNTRL\n"));
pm8001_mpi_local_phy_ctl(pm8001_ha, piomb);
break;
case OPC_OUB_DEV_REGIST:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_DEV_REGIST\n"));
pm8001_mpi_reg_resp(pm8001_ha, piomb);
break;
case OPC_OUB_DEREG_DEV:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("unregister the device\n"));
pm8001_mpi_dereg_resp(pm8001_ha, piomb);
break;
case OPC_OUB_GET_DEV_HANDLE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GET_DEV_HANDLE\n"));
break;
case OPC_OUB_SATA_COMP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SATA_COMP\n"));
mpi_sata_completion(pm8001_ha, piomb);
break;
case OPC_OUB_SATA_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SATA_EVENT\n"));
mpi_sata_event(pm8001_ha, piomb);
break;
case OPC_OUB_SSP_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SSP_EVENT\n"));
mpi_ssp_event(pm8001_ha, piomb);
break;
case OPC_OUB_DEV_HANDLE_ARRIV:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_DEV_HANDLE_ARRIV\n"));
/*This is for target*/
break;
case OPC_OUB_SSP_RECV_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SSP_RECV_EVENT\n"));
/*This is for target*/
break;
case OPC_OUB_FW_FLASH_UPDATE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_FW_FLASH_UPDATE\n"));
pm8001_mpi_fw_flash_update_resp(pm8001_ha, piomb);
break;
case OPC_OUB_GPIO_RESPONSE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GPIO_RESPONSE\n"));
break;
case OPC_OUB_GPIO_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GPIO_EVENT\n"));
break;
case OPC_OUB_GENERAL_EVENT:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GENERAL_EVENT\n"));
pm8001_mpi_general_event(pm8001_ha, piomb);
break;
case OPC_OUB_SSP_ABORT_RSP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SSP_ABORT_RSP\n"));
pm8001_mpi_task_abort_resp(pm8001_ha, piomb);
break;
case OPC_OUB_SATA_ABORT_RSP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SATA_ABORT_RSP\n"));
pm8001_mpi_task_abort_resp(pm8001_ha, piomb);
break;
case OPC_OUB_SAS_DIAG_MODE_START_END:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SAS_DIAG_MODE_START_END\n"));
break;
case OPC_OUB_SAS_DIAG_EXECUTE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SAS_DIAG_EXECUTE\n"));
break;
case OPC_OUB_GET_TIME_STAMP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GET_TIME_STAMP\n"));
break;
case OPC_OUB_SAS_HW_EVENT_ACK:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SAS_HW_EVENT_ACK\n"));
break;
case OPC_OUB_PORT_CONTROL:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_PORT_CONTROL\n"));
break;
case OPC_OUB_SMP_ABORT_RSP:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SMP_ABORT_RSP\n"));
pm8001_mpi_task_abort_resp(pm8001_ha, piomb);
break;
case OPC_OUB_GET_NVMD_DATA:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GET_NVMD_DATA\n"));
pm8001_mpi_get_nvmd_resp(pm8001_ha, piomb);
break;
case OPC_OUB_SET_NVMD_DATA:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SET_NVMD_DATA\n"));
pm8001_mpi_set_nvmd_resp(pm8001_ha, piomb);
break;
case OPC_OUB_DEVICE_HANDLE_REMOVAL:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_DEVICE_HANDLE_REMOVAL\n"));
break;
case OPC_OUB_SET_DEVICE_STATE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SET_DEVICE_STATE\n"));
pm8001_mpi_set_dev_state_resp(pm8001_ha, piomb);
break;
case OPC_OUB_GET_DEVICE_STATE:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_GET_DEVICE_STATE\n"));
break;
case OPC_OUB_SET_DEV_INFO:
PM8001_MSG_DBG(pm8001_ha,
pm8001_printk("OPC_OUB_SET_DEV_INFO\n"));
break;
/* spcv specifc commands */
case OPC_OUB_PHY_START_RESP:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"OPC_OUB_PHY_START_RESP opcode:%x\n", opc));
mpi_phy_start_resp(pm8001_ha, piomb);
break;
case OPC_OUB_PHY_STOP_RESP:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"OPC_OUB_PHY_STOP_RESP opcode:%x\n", opc));
mpi_phy_stop_resp(pm8001_ha, piomb);
break;
case OPC_OUB_SET_CONTROLLER_CONFIG:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"OPC_OUB_SET_CONTROLLER_CONFIG opcode:%x\n", opc));
mpi_set_controller_config_resp(pm8001_ha, piomb);
break;
case OPC_OUB_GET_CONTROLLER_CONFIG:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"OPC_OUB_GET_CONTROLLER_CONFIG opcode:%x\n", opc));
mpi_get_controller_config_resp(pm8001_ha, piomb);
break;
case OPC_OUB_GET_PHY_PROFILE:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"OPC_OUB_GET_PHY_PROFILE opcode:%x\n", opc));
mpi_get_phy_profile_resp(pm8001_ha, piomb);
break;
case OPC_OUB_FLASH_OP_EXT:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"OPC_OUB_FLASH_OP_EXT opcode:%x\n", opc));
mpi_flash_op_ext_resp(pm8001_ha, piomb);
break;
case OPC_OUB_SET_PHY_PROFILE:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"OPC_OUB_SET_PHY_PROFILE opcode:%x\n", opc));
mpi_set_phy_profile_resp(pm8001_ha, piomb);
break;
case OPC_OUB_KEK_MANAGEMENT_RESP:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"OPC_OUB_KEK_MANAGEMENT_RESP opcode:%x\n", opc));
mpi_kek_management_resp(pm8001_ha, piomb);
break;
case OPC_OUB_DEK_MANAGEMENT_RESP:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"OPC_OUB_DEK_MANAGEMENT_RESP opcode:%x\n", opc));
mpi_dek_management_resp(pm8001_ha, piomb);
break;
case OPC_OUB_SSP_COALESCED_COMP_RESP:
PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
"OPC_OUB_SSP_COALESCED_COMP_RESP opcode:%x\n", opc));
ssp_coalesced_comp_resp(pm8001_ha, piomb);
break;
default:
PM8001_DEVIO_DBG(pm8001_ha, pm8001_printk(
"Unknown outbound Queue IOMB OPC = 0x%x\n", opc));
break;
}
}
static void print_scratchpad_registers(struct pm8001_hba_info *pm8001_ha)
{
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("MSGU_SCRATCH_PAD_0: 0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("MSGU_SCRATCH_PAD_1:0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("MSGU_SCRATCH_PAD_2: 0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("MSGU_SCRATCH_PAD_3: 0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_3)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("MSGU_HOST_SCRATCH_PAD_0: 0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_HOST_SCRATCH_PAD_0)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("MSGU_HOST_SCRATCH_PAD_1: 0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_HOST_SCRATCH_PAD_1)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("MSGU_HOST_SCRATCH_PAD_2: 0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_HOST_SCRATCH_PAD_2)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("MSGU_HOST_SCRATCH_PAD_3: 0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_HOST_SCRATCH_PAD_3)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("MSGU_HOST_SCRATCH_PAD_4: 0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_HOST_SCRATCH_PAD_4)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("MSGU_HOST_SCRATCH_PAD_5: 0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_HOST_SCRATCH_PAD_5)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("MSGU_RSVD_SCRATCH_PAD_0: 0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_HOST_SCRATCH_PAD_6)));
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("MSGU_RSVD_SCRATCH_PAD_1: 0x%x\n",
pm8001_cr32(pm8001_ha, 0, MSGU_HOST_SCRATCH_PAD_7)));
}
static int process_oq(struct pm8001_hba_info *pm8001_ha, u8 vec)
{
struct outbound_queue_table *circularQ;
void *pMsg1 = NULL;
u8 uninitialized_var(bc);
u32 ret = MPI_IO_STATUS_FAIL;
unsigned long flags;
u32 regval;
if (vec == (pm8001_ha->number_of_intr - 1)) {
regval = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1);
if ((regval & SCRATCH_PAD_MIPSALL_READY) !=
SCRATCH_PAD_MIPSALL_READY) {
pm8001_ha->controller_fatal_error = true;
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk(
"Firmware Fatal error! Regval:0x%x\n", regval));
print_scratchpad_registers(pm8001_ha);
return ret;
}
}
spin_lock_irqsave(&pm8001_ha->lock, flags);
circularQ = &pm8001_ha->outbnd_q_tbl[vec];
do {
/* spurious interrupt during setup if kexec-ing and
* driver doing a doorbell access w/ the pre-kexec oq
* interrupt setup.
*/
if (!circularQ->pi_virt)
break;
ret = pm8001_mpi_msg_consume(pm8001_ha, circularQ, &pMsg1, &bc);
if (MPI_IO_STATUS_SUCCESS == ret) {
/* process the outbound message */
process_one_iomb(pm8001_ha, (void *)(pMsg1 - 4));
/* free the message from the outbound circular buffer */
pm8001_mpi_msg_free_set(pm8001_ha, pMsg1,
circularQ, bc);
}
if (MPI_IO_STATUS_BUSY == ret) {
/* Update the producer index from SPC */
circularQ->producer_index =
cpu_to_le32(pm8001_read_32(circularQ->pi_virt));
if (le32_to_cpu(circularQ->producer_index) ==
circularQ->consumer_idx)
/* OQ is empty */
break;
}
} while (1);
spin_unlock_irqrestore(&pm8001_ha->lock, flags);
return ret;
}
/* DMA_... to our direction translation. */
static const u8 data_dir_flags[] = {
[DMA_BIDIRECTIONAL] = DATA_DIR_BYRECIPIENT, /* UNSPECIFIED */
[DMA_TO_DEVICE] = DATA_DIR_OUT, /* OUTBOUND */
[DMA_FROM_DEVICE] = DATA_DIR_IN, /* INBOUND */
[DMA_NONE] = DATA_DIR_NONE, /* NO TRANSFER */
};
static void build_smp_cmd(u32 deviceID, __le32 hTag,
struct smp_req *psmp_cmd, int mode, int length)
{
psmp_cmd->tag = hTag;
psmp_cmd->device_id = cpu_to_le32(deviceID);
if (mode == SMP_DIRECT) {
length = length - 4; /* subtract crc */
psmp_cmd->len_ip_ir = cpu_to_le32(length << 16);
} else {
psmp_cmd->len_ip_ir = cpu_to_le32(1|(1 << 1));
}
}
/**
* pm8001_chip_smp_req - send a SMP task to FW
* @pm8001_ha: our hba card information.
* @ccb: the ccb information this request used.
*/
static int pm80xx_chip_smp_req(struct pm8001_hba_info *pm8001_ha,
struct pm8001_ccb_info *ccb)
{
int elem, rc;
struct sas_task *task = ccb->task;
struct domain_device *dev = task->dev;
struct pm8001_device *pm8001_dev = dev->lldd_dev;
struct scatterlist *sg_req, *sg_resp;
u32 req_len, resp_len;
struct smp_req smp_cmd;
u32 opc;
struct inbound_queue_table *circularQ;
char *preq_dma_addr = NULL;
__le64 tmp_addr;
u32 i, length;
memset(&smp_cmd, 0, sizeof(smp_cmd));
/*
* DMA-map SMP request, response buffers
*/
sg_req = &task->smp_task.smp_req;
elem = dma_map_sg(pm8001_ha->dev, sg_req, 1, DMA_TO_DEVICE);
if (!elem)
return -ENOMEM;
req_len = sg_dma_len(sg_req);
sg_resp = &task->smp_task.smp_resp;
elem = dma_map_sg(pm8001_ha->dev, sg_resp, 1, DMA_FROM_DEVICE);
if (!elem) {
rc = -ENOMEM;
goto err_out;
}
resp_len = sg_dma_len(sg_resp);
/* must be in dwords */
if ((req_len & 0x3) || (resp_len & 0x3)) {
rc = -EINVAL;
goto err_out_2;
}
opc = OPC_INB_SMP_REQUEST;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
smp_cmd.tag = cpu_to_le32(ccb->ccb_tag);
length = sg_req->length;
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("SMP Frame Length %d\n", sg_req->length));
if (!(length - 8))
pm8001_ha->smp_exp_mode = SMP_DIRECT;
else
pm8001_ha->smp_exp_mode = SMP_INDIRECT;
tmp_addr = cpu_to_le64((u64)sg_dma_address(&task->smp_task.smp_req));
preq_dma_addr = (char *)phys_to_virt(tmp_addr);
/* INDIRECT MODE command settings. Use DMA */
if (pm8001_ha->smp_exp_mode == SMP_INDIRECT) {
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("SMP REQUEST INDIRECT MODE\n"));
/* for SPCv indirect mode. Place the top 4 bytes of
* SMP Request header here. */
for (i = 0; i < 4; i++)
smp_cmd.smp_req16[i] = *(preq_dma_addr + i);
/* exclude top 4 bytes for SMP req header */
smp_cmd.long_smp_req.long_req_addr =
cpu_to_le64((u64)sg_dma_address
(&task->smp_task.smp_req) + 4);
/* exclude 4 bytes for SMP req header and CRC */
smp_cmd.long_smp_req.long_req_size =
cpu_to_le32((u32)sg_dma_len(&task->smp_task.smp_req)-8);
smp_cmd.long_smp_req.long_resp_addr =
cpu_to_le64((u64)sg_dma_address
(&task->smp_task.smp_resp));
smp_cmd.long_smp_req.long_resp_size =
cpu_to_le32((u32)sg_dma_len
(&task->smp_task.smp_resp)-4);
} else { /* DIRECT MODE */
smp_cmd.long_smp_req.long_req_addr =
cpu_to_le64((u64)sg_dma_address
(&task->smp_task.smp_req));
smp_cmd.long_smp_req.long_req_size =
cpu_to_le32((u32)sg_dma_len(&task->smp_task.smp_req)-4);
smp_cmd.long_smp_req.long_resp_addr =
cpu_to_le64((u64)sg_dma_address
(&task->smp_task.smp_resp));
smp_cmd.long_smp_req.long_resp_size =
cpu_to_le32
((u32)sg_dma_len(&task->smp_task.smp_resp)-4);
}
if (pm8001_ha->smp_exp_mode == SMP_DIRECT) {
PM8001_IO_DBG(pm8001_ha,
pm8001_printk("SMP REQUEST DIRECT MODE\n"));
for (i = 0; i < length; i++)
if (i < 16) {
smp_cmd.smp_req16[i] = *(preq_dma_addr+i);
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"Byte[%d]:%x (DMA data:%x)\n",
i, smp_cmd.smp_req16[i],
*(preq_dma_addr)));
} else {
smp_cmd.smp_req[i] = *(preq_dma_addr+i);
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"Byte[%d]:%x (DMA data:%x)\n",
i, smp_cmd.smp_req[i],
*(preq_dma_addr)));
}
}
build_smp_cmd(pm8001_dev->device_id, smp_cmd.tag,
&smp_cmd, pm8001_ha->smp_exp_mode, length);
rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &smp_cmd,
sizeof(smp_cmd), 0);
if (rc)
goto err_out_2;
return 0;
err_out_2:
dma_unmap_sg(pm8001_ha->dev, &ccb->task->smp_task.smp_resp, 1,
DMA_FROM_DEVICE);
err_out:
dma_unmap_sg(pm8001_ha->dev, &ccb->task->smp_task.smp_req, 1,
DMA_TO_DEVICE);
return rc;
}
static int check_enc_sas_cmd(struct sas_task *task)
{
u8 cmd = task->ssp_task.cmd->cmnd[0];
if (cmd == READ_10 || cmd == WRITE_10 || cmd == WRITE_VERIFY)
return 1;
else
return 0;
}
static int check_enc_sat_cmd(struct sas_task *task)
{
int ret = 0;
switch (task->ata_task.fis.command) {
case ATA_CMD_FPDMA_READ:
case ATA_CMD_READ_EXT:
case ATA_CMD_READ:
case ATA_CMD_FPDMA_WRITE:
case ATA_CMD_WRITE_EXT:
case ATA_CMD_WRITE:
case ATA_CMD_PIO_READ:
case ATA_CMD_PIO_READ_EXT:
case ATA_CMD_PIO_WRITE:
case ATA_CMD_PIO_WRITE_EXT:
ret = 1;
break;
default:
ret = 0;
break;
}
return ret;
}
/**
* pm80xx_chip_ssp_io_req - send a SSP task to FW
* @pm8001_ha: our hba card information.
* @ccb: the ccb information this request used.
*/
static int pm80xx_chip_ssp_io_req(struct pm8001_hba_info *pm8001_ha,
struct pm8001_ccb_info *ccb)
{
struct sas_task *task = ccb->task;
struct domain_device *dev = task->dev;
struct pm8001_device *pm8001_dev = dev->lldd_dev;
struct ssp_ini_io_start_req ssp_cmd;
u32 tag = ccb->ccb_tag;
int ret;
u64 phys_addr, start_addr, end_addr;
u32 end_addr_high, end_addr_low;
struct inbound_queue_table *circularQ;
u32 q_index;
u32 opc = OPC_INB_SSPINIIOSTART;
memset(&ssp_cmd, 0, sizeof(ssp_cmd));
memcpy(ssp_cmd.ssp_iu.lun, task->ssp_task.LUN, 8);
/* data address domain added for spcv; set to 0 by host,
* used internally by controller
* 0 for SAS 1.1 and SAS 2.0 compatible TLR
*/
ssp_cmd.dad_dir_m_tlr =
cpu_to_le32(data_dir_flags[task->data_dir] << 8 | 0x0);
ssp_cmd.data_len = cpu_to_le32(task->total_xfer_len);
ssp_cmd.device_id = cpu_to_le32(pm8001_dev->device_id);
ssp_cmd.tag = cpu_to_le32(tag);
if (task->ssp_task.enable_first_burst)
ssp_cmd.ssp_iu.efb_prio_attr |= 0x80;
ssp_cmd.ssp_iu.efb_prio_attr |= (task->ssp_task.task_prio << 3);
ssp_cmd.ssp_iu.efb_prio_attr |= (task->ssp_task.task_attr & 7);
memcpy(ssp_cmd.ssp_iu.cdb, task->ssp_task.cmd->cmnd,
task->ssp_task.cmd->cmd_len);
q_index = (u32) (pm8001_dev->id & 0x00ffffff) % PM8001_MAX_INB_NUM;
circularQ = &pm8001_ha->inbnd_q_tbl[q_index];
/* Check if encryption is set */
if (pm8001_ha->chip->encrypt &&
!(pm8001_ha->encrypt_info.status) && check_enc_sas_cmd(task)) {
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"Encryption enabled.Sending Encrypt SAS command 0x%x\n",
task->ssp_task.cmd->cmnd[0]));
opc = OPC_INB_SSP_INI_DIF_ENC_IO;
/* enable encryption. 0 for SAS 1.1 and SAS 2.0 compatible TLR*/
ssp_cmd.dad_dir_m_tlr = cpu_to_le32
((data_dir_flags[task->data_dir] << 8) | 0x20 | 0x0);
/* fill in PRD (scatter/gather) table, if any */
if (task->num_scatter > 1) {
pm8001_chip_make_sg(task->scatter,
ccb->n_elem, ccb->buf_prd);
phys_addr = ccb->ccb_dma_handle +
offsetof(struct pm8001_ccb_info, buf_prd[0]);
ssp_cmd.enc_addr_low =
cpu_to_le32(lower_32_bits(phys_addr));
ssp_cmd.enc_addr_high =
cpu_to_le32(upper_32_bits(phys_addr));
ssp_cmd.enc_esgl = cpu_to_le32(1<<31);
} else if (task->num_scatter == 1) {
u64 dma_addr = sg_dma_address(task->scatter);
ssp_cmd.enc_addr_low =
cpu_to_le32(lower_32_bits(dma_addr));
ssp_cmd.enc_addr_high =
cpu_to_le32(upper_32_bits(dma_addr));
ssp_cmd.enc_len = cpu_to_le32(task->total_xfer_len);
ssp_cmd.enc_esgl = 0;
/* Check 4G Boundary */
start_addr = cpu_to_le64(dma_addr);
end_addr = (start_addr + ssp_cmd.enc_len) - 1;
end_addr_low = cpu_to_le32(lower_32_bits(end_addr));
end_addr_high = cpu_to_le32(upper_32_bits(end_addr));
if (end_addr_high != ssp_cmd.enc_addr_high) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("The sg list address "
"start_addr=0x%016llx data_len=0x%x "
"end_addr_high=0x%08x end_addr_low="
"0x%08x has crossed 4G boundary\n",
start_addr, ssp_cmd.enc_len,
end_addr_high, end_addr_low));
pm8001_chip_make_sg(task->scatter, 1,
ccb->buf_prd);
phys_addr = ccb->ccb_dma_handle +
offsetof(struct pm8001_ccb_info,
buf_prd[0]);
ssp_cmd.enc_addr_low =
cpu_to_le32(lower_32_bits(phys_addr));
ssp_cmd.enc_addr_high =
cpu_to_le32(upper_32_bits(phys_addr));
ssp_cmd.enc_esgl = cpu_to_le32(1<<31);
}
} else if (task->num_scatter == 0) {
ssp_cmd.enc_addr_low = 0;
ssp_cmd.enc_addr_high = 0;
ssp_cmd.enc_len = cpu_to_le32(task->total_xfer_len);
ssp_cmd.enc_esgl = 0;
}
/* XTS mode. All other fields are 0 */
ssp_cmd.key_cmode = 0x6 << 4;
/* set tweak values. Should be the start lba */
ssp_cmd.twk_val0 = cpu_to_le32((task->ssp_task.cmd->cmnd[2] << 24) |
(task->ssp_task.cmd->cmnd[3] << 16) |
(task->ssp_task.cmd->cmnd[4] << 8) |
(task->ssp_task.cmd->cmnd[5]));
} else {
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"Sending Normal SAS command 0x%x inb q %x\n",
task->ssp_task.cmd->cmnd[0], q_index));
/* fill in PRD (scatter/gather) table, if any */
if (task->num_scatter > 1) {
pm8001_chip_make_sg(task->scatter, ccb->n_elem,
ccb->buf_prd);
phys_addr = ccb->ccb_dma_handle +
offsetof(struct pm8001_ccb_info, buf_prd[0]);
ssp_cmd.addr_low =
cpu_to_le32(lower_32_bits(phys_addr));
ssp_cmd.addr_high =
cpu_to_le32(upper_32_bits(phys_addr));
ssp_cmd.esgl = cpu_to_le32(1<<31);
} else if (task->num_scatter == 1) {
u64 dma_addr = sg_dma_address(task->scatter);
ssp_cmd.addr_low = cpu_to_le32(lower_32_bits(dma_addr));
ssp_cmd.addr_high =
cpu_to_le32(upper_32_bits(dma_addr));
ssp_cmd.len = cpu_to_le32(task->total_xfer_len);
ssp_cmd.esgl = 0;
/* Check 4G Boundary */
start_addr = cpu_to_le64(dma_addr);
end_addr = (start_addr + ssp_cmd.len) - 1;
end_addr_low = cpu_to_le32(lower_32_bits(end_addr));
end_addr_high = cpu_to_le32(upper_32_bits(end_addr));
if (end_addr_high != ssp_cmd.addr_high) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("The sg list address "
"start_addr=0x%016llx data_len=0x%x "
"end_addr_high=0x%08x end_addr_low="
"0x%08x has crossed 4G boundary\n",
start_addr, ssp_cmd.len,
end_addr_high, end_addr_low));
pm8001_chip_make_sg(task->scatter, 1,
ccb->buf_prd);
phys_addr = ccb->ccb_dma_handle +
offsetof(struct pm8001_ccb_info,
buf_prd[0]);
ssp_cmd.addr_low =
cpu_to_le32(lower_32_bits(phys_addr));
ssp_cmd.addr_high =
cpu_to_le32(upper_32_bits(phys_addr));
ssp_cmd.esgl = cpu_to_le32(1<<31);
}
} else if (task->num_scatter == 0) {
ssp_cmd.addr_low = 0;
ssp_cmd.addr_high = 0;
ssp_cmd.len = cpu_to_le32(task->total_xfer_len);
ssp_cmd.esgl = 0;
}
}
q_index = (u32) (pm8001_dev->id & 0x00ffffff) % PM8001_MAX_OUTB_NUM;
ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc,
&ssp_cmd, sizeof(ssp_cmd), q_index);
return ret;
}
static int pm80xx_chip_sata_req(struct pm8001_hba_info *pm8001_ha,
struct pm8001_ccb_info *ccb)
{
struct sas_task *task = ccb->task;
struct domain_device *dev = task->dev;
struct pm8001_device *pm8001_ha_dev = dev->lldd_dev;
u32 tag = ccb->ccb_tag;
int ret;
u32 q_index;
struct sata_start_req sata_cmd;
u32 hdr_tag, ncg_tag = 0;
u64 phys_addr, start_addr, end_addr;
u32 end_addr_high, end_addr_low;
u32 ATAP = 0x0;
u32 dir;
struct inbound_queue_table *circularQ;
unsigned long flags;
u32 opc = OPC_INB_SATA_HOST_OPSTART;
memset(&sata_cmd, 0, sizeof(sata_cmd));
q_index = (u32) (pm8001_ha_dev->id & 0x00ffffff) % PM8001_MAX_INB_NUM;
circularQ = &pm8001_ha->inbnd_q_tbl[q_index];
if (task->data_dir == DMA_NONE) {
ATAP = 0x04; /* no data*/
PM8001_IO_DBG(pm8001_ha, pm8001_printk("no data\n"));
} else if (likely(!task->ata_task.device_control_reg_update)) {
if (task->ata_task.dma_xfer) {
ATAP = 0x06; /* DMA */
PM8001_IO_DBG(pm8001_ha, pm8001_printk("DMA\n"));
} else {
ATAP = 0x05; /* PIO*/
PM8001_IO_DBG(pm8001_ha, pm8001_printk("PIO\n"));
}
if (task->ata_task.use_ncq &&
dev->sata_dev.class != ATA_DEV_ATAPI) {
ATAP = 0x07; /* FPDMA */
PM8001_IO_DBG(pm8001_ha, pm8001_printk("FPDMA\n"));
}
}
if (task->ata_task.use_ncq && pm8001_get_ncq_tag(task, &hdr_tag)) {
task->ata_task.fis.sector_count |= (u8) (hdr_tag << 3);
ncg_tag = hdr_tag;
}
dir = data_dir_flags[task->data_dir] << 8;
sata_cmd.tag = cpu_to_le32(tag);
sata_cmd.device_id = cpu_to_le32(pm8001_ha_dev->device_id);
sata_cmd.data_len = cpu_to_le32(task->total_xfer_len);
sata_cmd.sata_fis = task->ata_task.fis;
if (likely(!task->ata_task.device_control_reg_update))
sata_cmd.sata_fis.flags |= 0x80;/* C=1: update ATA cmd reg */
sata_cmd.sata_fis.flags &= 0xF0;/* PM_PORT field shall be 0 */
/* Check if encryption is set */
if (pm8001_ha->chip->encrypt &&
!(pm8001_ha->encrypt_info.status) && check_enc_sat_cmd(task)) {
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"Encryption enabled.Sending Encrypt SATA cmd 0x%x\n",
sata_cmd.sata_fis.command));
opc = OPC_INB_SATA_DIF_ENC_IO;
/* set encryption bit */
sata_cmd.ncqtag_atap_dir_m_dad =
cpu_to_le32(((ncg_tag & 0xff)<<16)|
((ATAP & 0x3f) << 10) | 0x20 | dir);
/* dad (bit 0-1) is 0 */
/* fill in PRD (scatter/gather) table, if any */
if (task->num_scatter > 1) {
pm8001_chip_make_sg(task->scatter,
ccb->n_elem, ccb->buf_prd);
phys_addr = ccb->ccb_dma_handle +
offsetof(struct pm8001_ccb_info, buf_prd[0]);
sata_cmd.enc_addr_low = lower_32_bits(phys_addr);
sata_cmd.enc_addr_high = upper_32_bits(phys_addr);
sata_cmd.enc_esgl = cpu_to_le32(1 << 31);
} else if (task->num_scatter == 1) {
u64 dma_addr = sg_dma_address(task->scatter);
sata_cmd.enc_addr_low = lower_32_bits(dma_addr);
sata_cmd.enc_addr_high = upper_32_bits(dma_addr);
sata_cmd.enc_len = cpu_to_le32(task->total_xfer_len);
sata_cmd.enc_esgl = 0;
/* Check 4G Boundary */
start_addr = cpu_to_le64(dma_addr);
end_addr = (start_addr + sata_cmd.enc_len) - 1;
end_addr_low = cpu_to_le32(lower_32_bits(end_addr));
end_addr_high = cpu_to_le32(upper_32_bits(end_addr));
if (end_addr_high != sata_cmd.enc_addr_high) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("The sg list address "
"start_addr=0x%016llx data_len=0x%x "
"end_addr_high=0x%08x end_addr_low"
"=0x%08x has crossed 4G boundary\n",
start_addr, sata_cmd.enc_len,
end_addr_high, end_addr_low));
pm8001_chip_make_sg(task->scatter, 1,
ccb->buf_prd);
phys_addr = ccb->ccb_dma_handle +
offsetof(struct pm8001_ccb_info,
buf_prd[0]);
sata_cmd.enc_addr_low =
lower_32_bits(phys_addr);
sata_cmd.enc_addr_high =
upper_32_bits(phys_addr);
sata_cmd.enc_esgl =
cpu_to_le32(1 << 31);
}
} else if (task->num_scatter == 0) {
sata_cmd.enc_addr_low = 0;
sata_cmd.enc_addr_high = 0;
sata_cmd.enc_len = cpu_to_le32(task->total_xfer_len);
sata_cmd.enc_esgl = 0;
}
/* XTS mode. All other fields are 0 */
sata_cmd.key_index_mode = 0x6 << 4;
/* set tweak values. Should be the start lba */
sata_cmd.twk_val0 =
cpu_to_le32((sata_cmd.sata_fis.lbal_exp << 24) |
(sata_cmd.sata_fis.lbah << 16) |
(sata_cmd.sata_fis.lbam << 8) |
(sata_cmd.sata_fis.lbal));
sata_cmd.twk_val1 =
cpu_to_le32((sata_cmd.sata_fis.lbah_exp << 8) |
(sata_cmd.sata_fis.lbam_exp));
} else {
PM8001_IO_DBG(pm8001_ha, pm8001_printk(
"Sending Normal SATA command 0x%x inb %x\n",
sata_cmd.sata_fis.command, q_index));
/* dad (bit 0-1) is 0 */
sata_cmd.ncqtag_atap_dir_m_dad =
cpu_to_le32(((ncg_tag & 0xff)<<16) |
((ATAP & 0x3f) << 10) | dir);
/* fill in PRD (scatter/gather) table, if any */
if (task->num_scatter > 1) {
pm8001_chip_make_sg(task->scatter,
ccb->n_elem, ccb->buf_prd);
phys_addr = ccb->ccb_dma_handle +
offsetof(struct pm8001_ccb_info, buf_prd[0]);
sata_cmd.addr_low = lower_32_bits(phys_addr);
sata_cmd.addr_high = upper_32_bits(phys_addr);
sata_cmd.esgl = cpu_to_le32(1 << 31);
} else if (task->num_scatter == 1) {
u64 dma_addr = sg_dma_address(task->scatter);
sata_cmd.addr_low = lower_32_bits(dma_addr);
sata_cmd.addr_high = upper_32_bits(dma_addr);
sata_cmd.len = cpu_to_le32(task->total_xfer_len);
sata_cmd.esgl = 0;
/* Check 4G Boundary */
start_addr = cpu_to_le64(dma_addr);
end_addr = (start_addr + sata_cmd.len) - 1;
end_addr_low = cpu_to_le32(lower_32_bits(end_addr));
end_addr_high = cpu_to_le32(upper_32_bits(end_addr));
if (end_addr_high != sata_cmd.addr_high) {
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("The sg list address "
"start_addr=0x%016llx data_len=0x%x"
"end_addr_high=0x%08x end_addr_low="
"0x%08x has crossed 4G boundary\n",
start_addr, sata_cmd.len,
end_addr_high, end_addr_low));
pm8001_chip_make_sg(task->scatter, 1,
ccb->buf_prd);
phys_addr = ccb->ccb_dma_handle +
offsetof(struct pm8001_ccb_info,
buf_prd[0]);
sata_cmd.addr_low =
lower_32_bits(phys_addr);
sata_cmd.addr_high =
upper_32_bits(phys_addr);
sata_cmd.esgl = cpu_to_le32(1 << 31);
}
} else if (task->num_scatter == 0) {
sata_cmd.addr_low = 0;
sata_cmd.addr_high = 0;
sata_cmd.len = cpu_to_le32(task->total_xfer_len);
sata_cmd.esgl = 0;
}
/* scsi cdb */
sata_cmd.atapi_scsi_cdb[0] =
cpu_to_le32(((task->ata_task.atapi_packet[0]) |
(task->ata_task.atapi_packet[1] << 8) |
(task->ata_task.atapi_packet[2] << 16) |
(task->ata_task.atapi_packet[3] << 24)));
sata_cmd.atapi_scsi_cdb[1] =
cpu_to_le32(((task->ata_task.atapi_packet[4]) |
(task->ata_task.atapi_packet[5] << 8) |
(task->ata_task.atapi_packet[6] << 16) |
(task->ata_task.atapi_packet[7] << 24)));
sata_cmd.atapi_scsi_cdb[2] =
cpu_to_le32(((task->ata_task.atapi_packet[8]) |
(task->ata_task.atapi_packet[9] << 8) |
(task->ata_task.atapi_packet[10] << 16) |
(task->ata_task.atapi_packet[11] << 24)));
sata_cmd.atapi_scsi_cdb[3] =
cpu_to_le32(((task->ata_task.atapi_packet[12]) |
(task->ata_task.atapi_packet[13] << 8) |
(task->ata_task.atapi_packet[14] << 16) |
(task->ata_task.atapi_packet[15] << 24)));
}
/* Check for read log for failed drive and return */
if (sata_cmd.sata_fis.command == 0x2f) {
if (pm8001_ha_dev && ((pm8001_ha_dev->id & NCQ_READ_LOG_FLAG) ||
(pm8001_ha_dev->id & NCQ_ABORT_ALL_FLAG) ||
(pm8001_ha_dev->id & NCQ_2ND_RLE_FLAG))) {
struct task_status_struct *ts;
pm8001_ha_dev->id &= 0xDFFFFFFF;
ts = &task->task_status;
spin_lock_irqsave(&task->task_state_lock, flags);
ts->resp = SAS_TASK_COMPLETE;
ts->stat = SAM_STAT_GOOD;
task->task_state_flags &= ~SAS_TASK_STATE_PENDING;
task->task_state_flags &= ~SAS_TASK_AT_INITIATOR;
task->task_state_flags |= SAS_TASK_STATE_DONE;
if (unlikely((task->task_state_flags &
SAS_TASK_STATE_ABORTED))) {
spin_unlock_irqrestore(&task->task_state_lock,
flags);
PM8001_FAIL_DBG(pm8001_ha,
pm8001_printk("task 0x%p resp 0x%x "
" stat 0x%x but aborted by upper layer "
"\n", task, ts->resp, ts->stat));
pm8001_ccb_task_free(pm8001_ha, task, ccb, tag);
return 0;
} else {
spin_unlock_irqrestore(&task->task_state_lock,
flags);
pm8001_ccb_task_free_done(pm8001_ha, task,
ccb, tag);
return 0;
}
}
}
q_index = (u32) (pm8001_ha_dev->id & 0x00ffffff) % PM8001_MAX_OUTB_NUM;
ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc,
&sata_cmd, sizeof(sata_cmd), q_index);
return ret;
}
/**
* pm80xx_chip_phy_start_req - start phy via PHY_START COMMAND
* @pm8001_ha: our hba card information.
* @num: the inbound queue number
* @phy_id: the phy id which we wanted to start up.
*/
static int
pm80xx_chip_phy_start_req(struct pm8001_hba_info *pm8001_ha, u8 phy_id)
{
struct phy_start_req payload;
struct inbound_queue_table *circularQ;
int ret;
u32 tag = 0x01;
u32 opcode = OPC_INB_PHYSTART;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
memset(&payload, 0, sizeof(payload));
payload.tag = cpu_to_le32(tag);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("PHY START REQ for phy_id %d\n", phy_id));
payload.ase_sh_lm_slr_phyid = cpu_to_le32(SPINHOLD_DISABLE |
LINKMODE_AUTO | pm8001_ha->link_rate | phy_id);
/* SSC Disable and SAS Analog ST configuration */
/**
payload.ase_sh_lm_slr_phyid =
cpu_to_le32(SSC_DISABLE_30 | SAS_ASE | SPINHOLD_DISABLE |
LINKMODE_AUTO | LINKRATE_15 | LINKRATE_30 | LINKRATE_60 |
phy_id);
Have to add "SAS PHY Analog Setup SPASTI 1 Byte" Based on need
**/
payload.sas_identify.dev_type = SAS_END_DEVICE;
payload.sas_identify.initiator_bits = SAS_PROTOCOL_ALL;
memcpy(payload.sas_identify.sas_addr,
&pm8001_ha->sas_addr, SAS_ADDR_SIZE);
payload.sas_identify.phy_id = phy_id;
ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opcode, &payload,
sizeof(payload), 0);
return ret;
}
/**
* pm8001_chip_phy_stop_req - start phy via PHY_STOP COMMAND
* @pm8001_ha: our hba card information.
* @num: the inbound queue number
* @phy_id: the phy id which we wanted to start up.
*/
static int pm80xx_chip_phy_stop_req(struct pm8001_hba_info *pm8001_ha,
u8 phy_id)
{
struct phy_stop_req payload;
struct inbound_queue_table *circularQ;
int ret;
u32 tag = 0x01;
u32 opcode = OPC_INB_PHYSTOP;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
memset(&payload, 0, sizeof(payload));
payload.tag = cpu_to_le32(tag);
payload.phy_id = cpu_to_le32(phy_id);
ret = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opcode, &payload,
sizeof(payload), 0);
return ret;
}
/**
* see comments on pm8001_mpi_reg_resp.
*/
static int pm80xx_chip_reg_dev_req(struct pm8001_hba_info *pm8001_ha,
struct pm8001_device *pm8001_dev, u32 flag)
{
struct reg_dev_req payload;
u32 opc;
u32 stp_sspsmp_sata = 0x4;
struct inbound_queue_table *circularQ;
u32 linkrate, phy_id;
int rc, tag = 0xdeadbeef;
struct pm8001_ccb_info *ccb;
u8 retryFlag = 0x1;
u16 firstBurstSize = 0;
u16 ITNT = 2000;
struct domain_device *dev = pm8001_dev->sas_device;
struct domain_device *parent_dev = dev->parent;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
memset(&payload, 0, sizeof(payload));
rc = pm8001_tag_alloc(pm8001_ha, &tag);
if (rc)
return rc;
ccb = &pm8001_ha->ccb_info[tag];
ccb->device = pm8001_dev;
ccb->ccb_tag = tag;
payload.tag = cpu_to_le32(tag);
if (flag == 1) {
stp_sspsmp_sata = 0x02; /*direct attached sata */
} else {
if (pm8001_dev->dev_type == SAS_SATA_DEV)
stp_sspsmp_sata = 0x00; /* stp*/
else if (pm8001_dev->dev_type == SAS_END_DEVICE ||
pm8001_dev->dev_type == SAS_EDGE_EXPANDER_DEVICE ||
pm8001_dev->dev_type == SAS_FANOUT_EXPANDER_DEVICE)
stp_sspsmp_sata = 0x01; /*ssp or smp*/
}
if (parent_dev && dev_is_expander(parent_dev->dev_type))
phy_id = parent_dev->ex_dev.ex_phy->phy_id;
else
phy_id = pm8001_dev->attached_phy;
opc = OPC_INB_REG_DEV;
linkrate = (pm8001_dev->sas_device->linkrate < dev->port->linkrate) ?
pm8001_dev->sas_device->linkrate : dev->port->linkrate;
payload.phyid_portid =
cpu_to_le32(((pm8001_dev->sas_device->port->id) & 0xFF) |
((phy_id & 0xFF) << 8));
payload.dtype_dlr_mcn_ir_retry = cpu_to_le32((retryFlag & 0x01) |
((linkrate & 0x0F) << 24) |
((stp_sspsmp_sata & 0x03) << 28));
payload.firstburstsize_ITNexustimeout =
cpu_to_le32(ITNT | (firstBurstSize * 0x10000));
memcpy(payload.sas_addr, pm8001_dev->sas_device->sas_addr,
SAS_ADDR_SIZE);
rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload,
sizeof(payload), 0);
if (rc)
pm8001_tag_free(pm8001_ha, tag);
return rc;
}
/**
* pm80xx_chip_phy_ctl_req - support the local phy operation
* @pm8001_ha: our hba card information.
* @num: the inbound queue number
* @phy_id: the phy id which we wanted to operate
* @phy_op:
*/
static int pm80xx_chip_phy_ctl_req(struct pm8001_hba_info *pm8001_ha,
u32 phyId, u32 phy_op)
{
u32 tag;
int rc;
struct local_phy_ctl_req payload;
struct inbound_queue_table *circularQ;
u32 opc = OPC_INB_LOCAL_PHY_CONTROL;
memset(&payload, 0, sizeof(payload));
rc = pm8001_tag_alloc(pm8001_ha, &tag);
if (rc)
return rc;
circularQ = &pm8001_ha->inbnd_q_tbl[0];
payload.tag = cpu_to_le32(tag);
payload.phyop_phyid =
cpu_to_le32(((phy_op & 0xFF) << 8) | (phyId & 0xFF));
return pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload,
sizeof(payload), 0);
}
static u32 pm80xx_chip_is_our_interrupt(struct pm8001_hba_info *pm8001_ha)
{
#ifdef PM8001_USE_MSIX
return 1;
#else
u32 value;
value = pm8001_cr32(pm8001_ha, 0, MSGU_ODR);
if (value)
return 1;
return 0;
#endif
}
/**
* pm8001_chip_isr - PM8001 isr handler.
* @pm8001_ha: our hba card information.
* @irq: irq number.
* @stat: stat.
*/
static irqreturn_t
pm80xx_chip_isr(struct pm8001_hba_info *pm8001_ha, u8 vec)
{
pm80xx_chip_interrupt_disable(pm8001_ha, vec);
PM8001_DEVIO_DBG(pm8001_ha, pm8001_printk(
"irq vec %d, ODMR:0x%x\n",
vec, pm8001_cr32(pm8001_ha, 0, 0x30)));
process_oq(pm8001_ha, vec);
pm80xx_chip_interrupt_enable(pm8001_ha, vec);
return IRQ_HANDLED;
}
void mpi_set_phy_profile_req(struct pm8001_hba_info *pm8001_ha,
u32 operation, u32 phyid, u32 length, u32 *buf)
{
u32 tag , i, j = 0;
int rc;
struct set_phy_profile_req payload;
struct inbound_queue_table *circularQ;
u32 opc = OPC_INB_SET_PHY_PROFILE;
memset(&payload, 0, sizeof(payload));
rc = pm8001_tag_alloc(pm8001_ha, &tag);
if (rc)
PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("Invalid tag\n"));
circularQ = &pm8001_ha->inbnd_q_tbl[0];
payload.tag = cpu_to_le32(tag);
payload.ppc_phyid = (((operation & 0xF) << 8) | (phyid & 0xFF));
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk(" phy profile command for phy %x ,length is %d\n",
payload.ppc_phyid, length));
for (i = length; i < (length + PHY_DWORD_LENGTH - 1); i++) {
payload.reserved[j] = cpu_to_le32(*((u32 *)buf + i));
j++;
}
rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload,
sizeof(payload), 0);
if (rc)
pm8001_tag_free(pm8001_ha, tag);
}
void pm8001_set_phy_profile(struct pm8001_hba_info *pm8001_ha,
u32 length, u8 *buf)
{
u32 i;
for (i = 0; i < pm8001_ha->chip->n_phy; i++) {
mpi_set_phy_profile_req(pm8001_ha,
SAS_PHY_ANALOG_SETTINGS_PAGE, i, length, (u32 *)buf);
length = length + PHY_DWORD_LENGTH;
}
PM8001_INIT_DBG(pm8001_ha, pm8001_printk("phy settings completed\n"));
}
void pm8001_set_phy_profile_single(struct pm8001_hba_info *pm8001_ha,
u32 phy, u32 length, u32 *buf)
{
u32 tag, opc;
int rc, i;
struct set_phy_profile_req payload;
struct inbound_queue_table *circularQ;
memset(&payload, 0, sizeof(payload));
rc = pm8001_tag_alloc(pm8001_ha, &tag);
if (rc)
PM8001_INIT_DBG(pm8001_ha, pm8001_printk("Invalid tag"));
circularQ = &pm8001_ha->inbnd_q_tbl[0];
opc = OPC_INB_SET_PHY_PROFILE;
payload.tag = cpu_to_le32(tag);
payload.ppc_phyid = (((SAS_PHY_ANALOG_SETTINGS_PAGE & 0xF) << 8)
| (phy & 0xFF));
for (i = 0; i < length; i++)
payload.reserved[i] = cpu_to_le32(*(buf + i));
rc = pm8001_mpi_build_cmd(pm8001_ha, circularQ, opc, &payload,
sizeof(payload), 0);
if (rc)
pm8001_tag_free(pm8001_ha, tag);
PM8001_INIT_DBG(pm8001_ha,
pm8001_printk("PHY %d settings applied", phy));
}
const struct pm8001_dispatch pm8001_80xx_dispatch = {
.name = "pmc80xx",
.chip_init = pm80xx_chip_init,
.chip_soft_rst = pm80xx_chip_soft_rst,
.chip_rst = pm80xx_hw_chip_rst,
.chip_iounmap = pm8001_chip_iounmap,
.isr = pm80xx_chip_isr,
.is_our_interrupt = pm80xx_chip_is_our_interrupt,
.isr_process_oq = process_oq,
.interrupt_enable = pm80xx_chip_interrupt_enable,
.interrupt_disable = pm80xx_chip_interrupt_disable,
.make_prd = pm8001_chip_make_sg,
.smp_req = pm80xx_chip_smp_req,
.ssp_io_req = pm80xx_chip_ssp_io_req,
.sata_req = pm80xx_chip_sata_req,
.phy_start_req = pm80xx_chip_phy_start_req,
.phy_stop_req = pm80xx_chip_phy_stop_req,
.reg_dev_req = pm80xx_chip_reg_dev_req,
.dereg_dev_req = pm8001_chip_dereg_dev_req,
.phy_ctl_req = pm80xx_chip_phy_ctl_req,
.task_abort = pm8001_chip_abort_task,
.ssp_tm_req = pm8001_chip_ssp_tm_req,
.get_nvmd_req = pm8001_chip_get_nvmd_req,
.set_nvmd_req = pm8001_chip_set_nvmd_req,
.fw_flash_update_req = pm8001_chip_fw_flash_update_req,
.set_dev_state_req = pm8001_chip_set_dev_state_req,
};
Reference in New Issue View Git Blame Copy Permalink