linux/drivers/mmc/host/mmci_qcom_dml.c
Thomas Gleixner 97fb5e8d9b treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 284
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 and
  only version 2 as published by the free software foundation this
  program is distributed in the hope that it will be useful but
  without any warranty without even the implied warranty of
  merchantability or fitness for a particular purpose see the gnu
  general public license for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 294 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:36:37 +02:00

203 lines
5.7 KiB
C

// SPDX-License-Identifier: GPL-2.0-only
/*
*
* Copyright (c) 2011, The Linux Foundation. All rights reserved.
*/
#include <linux/of.h>
#include <linux/of_dma.h>
#include <linux/bitops.h>
#include <linux/mmc/host.h>
#include <linux/mmc/card.h>
#include "mmci.h"
/* Registers */
#define DML_CONFIG 0x00
#define PRODUCER_CRCI_MSK GENMASK(1, 0)
#define PRODUCER_CRCI_DISABLE 0
#define PRODUCER_CRCI_X_SEL BIT(0)
#define PRODUCER_CRCI_Y_SEL BIT(1)
#define CONSUMER_CRCI_MSK GENMASK(3, 2)
#define CONSUMER_CRCI_DISABLE 0
#define CONSUMER_CRCI_X_SEL BIT(2)
#define CONSUMER_CRCI_Y_SEL BIT(3)
#define PRODUCER_TRANS_END_EN BIT(4)
#define BYPASS BIT(16)
#define DIRECT_MODE BIT(17)
#define INFINITE_CONS_TRANS BIT(18)
#define DML_SW_RESET 0x08
#define DML_PRODUCER_START 0x0c
#define DML_CONSUMER_START 0x10
#define DML_PRODUCER_PIPE_LOGICAL_SIZE 0x14
#define DML_CONSUMER_PIPE_LOGICAL_SIZE 0x18
#define DML_PIPE_ID 0x1c
#define PRODUCER_PIPE_ID_SHFT 0
#define PRODUCER_PIPE_ID_MSK GENMASK(4, 0)
#define CONSUMER_PIPE_ID_SHFT 16
#define CONSUMER_PIPE_ID_MSK GENMASK(20, 16)
#define DML_PRODUCER_BAM_BLOCK_SIZE 0x24
#define DML_PRODUCER_BAM_TRANS_SIZE 0x28
/* other definitions */
#define PRODUCER_PIPE_LOGICAL_SIZE 4096
#define CONSUMER_PIPE_LOGICAL_SIZE 4096
#define DML_OFFSET 0x800
static int qcom_dma_start(struct mmci_host *host, unsigned int *datactrl)
{
u32 config;
void __iomem *base = host->base + DML_OFFSET;
struct mmc_data *data = host->data;
int ret = mmci_dmae_start(host, datactrl);
if (ret)
return ret;
if (data->flags & MMC_DATA_READ) {
/* Read operation: configure DML for producer operation */
/* Set producer CRCI-x and disable consumer CRCI */
config = readl_relaxed(base + DML_CONFIG);
config = (config & ~PRODUCER_CRCI_MSK) | PRODUCER_CRCI_X_SEL;
config = (config & ~CONSUMER_CRCI_MSK) | CONSUMER_CRCI_DISABLE;
writel_relaxed(config, base + DML_CONFIG);
/* Set the Producer BAM block size */
writel_relaxed(data->blksz, base + DML_PRODUCER_BAM_BLOCK_SIZE);
/* Set Producer BAM Transaction size */
writel_relaxed(data->blocks * data->blksz,
base + DML_PRODUCER_BAM_TRANS_SIZE);
/* Set Producer Transaction End bit */
config = readl_relaxed(base + DML_CONFIG);
config |= PRODUCER_TRANS_END_EN;
writel_relaxed(config, base + DML_CONFIG);
/* Trigger producer */
writel_relaxed(1, base + DML_PRODUCER_START);
} else {
/* Write operation: configure DML for consumer operation */
/* Set consumer CRCI-x and disable producer CRCI*/
config = readl_relaxed(base + DML_CONFIG);
config = (config & ~CONSUMER_CRCI_MSK) | CONSUMER_CRCI_X_SEL;
config = (config & ~PRODUCER_CRCI_MSK) | PRODUCER_CRCI_DISABLE;
writel_relaxed(config, base + DML_CONFIG);
/* Clear Producer Transaction End bit */
config = readl_relaxed(base + DML_CONFIG);
config &= ~PRODUCER_TRANS_END_EN;
writel_relaxed(config, base + DML_CONFIG);
/* Trigger consumer */
writel_relaxed(1, base + DML_CONSUMER_START);
}
/* make sure the dml is configured before dma is triggered */
wmb();
return 0;
}
static int of_get_dml_pipe_index(struct device_node *np, const char *name)
{
int index;
struct of_phandle_args dma_spec;
index = of_property_match_string(np, "dma-names", name);
if (index < 0)
return -ENODEV;
if (of_parse_phandle_with_args(np, "dmas", "#dma-cells", index,
&dma_spec))
return -ENODEV;
if (dma_spec.args_count)
return dma_spec.args[0];
return -ENODEV;
}
/* Initialize the dml hardware connected to SD Card controller */
static int qcom_dma_setup(struct mmci_host *host)
{
u32 config;
void __iomem *base;
int consumer_id, producer_id;
struct device_node *np = host->mmc->parent->of_node;
if (mmci_dmae_setup(host))
return -EINVAL;
consumer_id = of_get_dml_pipe_index(np, "tx");
producer_id = of_get_dml_pipe_index(np, "rx");
if (producer_id < 0 || consumer_id < 0) {
mmci_dmae_release(host);
return -EINVAL;
}
base = host->base + DML_OFFSET;
/* Reset the DML block */
writel_relaxed(1, base + DML_SW_RESET);
/* Disable the producer and consumer CRCI */
config = (PRODUCER_CRCI_DISABLE | CONSUMER_CRCI_DISABLE);
/*
* Disable the bypass mode. Bypass mode will only be used
* if data transfer is to happen in PIO mode and don't
* want the BAM interface to connect with SDCC-DML.
*/
config &= ~BYPASS;
/*
* Disable direct mode as we don't DML to MASTER the AHB bus.
* BAM connected with DML should MASTER the AHB bus.
*/
config &= ~DIRECT_MODE;
/*
* Disable infinite mode transfer as we won't be doing any
* infinite size data transfers. All data transfer will be
* of finite data size.
*/
config &= ~INFINITE_CONS_TRANS;
writel_relaxed(config, base + DML_CONFIG);
/*
* Initialize the logical BAM pipe size for producer
* and consumer.
*/
writel_relaxed(PRODUCER_PIPE_LOGICAL_SIZE,
base + DML_PRODUCER_PIPE_LOGICAL_SIZE);
writel_relaxed(CONSUMER_PIPE_LOGICAL_SIZE,
base + DML_CONSUMER_PIPE_LOGICAL_SIZE);
/* Initialize Producer/consumer pipe id */
writel_relaxed(producer_id | (consumer_id << CONSUMER_PIPE_ID_SHFT),
base + DML_PIPE_ID);
/* Make sure dml initialization is finished */
mb();
return 0;
}
static u32 qcom_get_dctrl_cfg(struct mmci_host *host)
{
return MCI_DPSM_ENABLE | (host->data->blksz << 4);
}
static struct mmci_host_ops qcom_variant_ops = {
.prep_data = mmci_dmae_prep_data,
.unprep_data = mmci_dmae_unprep_data,
.get_datactrl_cfg = qcom_get_dctrl_cfg,
.get_next_data = mmci_dmae_get_next_data,
.dma_setup = qcom_dma_setup,
.dma_release = mmci_dmae_release,
.dma_start = qcom_dma_start,
.dma_finalize = mmci_dmae_finalize,
.dma_error = mmci_dmae_error,
};
void qcom_variant_init(struct mmci_host *host)
{
host->ops = &qcom_variant_ops;
}