mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-11 04:18:39 +08:00
cebaa386d5
For loops with multiple initializers and increments are hard to read and reason about, simplify this by using the looping index to index into the hwspinlock array. Signed-off-by: Andrew Davis <afd@ti.com> Link: https://lore.kernel.org/r/20240208165114.63148-4-afd@ti.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
160 lines
4.2 KiB
C
160 lines
4.2 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* OMAP hardware spinlock driver
|
|
*
|
|
* Copyright (C) 2010-2021 Texas Instruments Incorporated - https://www.ti.com
|
|
*
|
|
* Contact: Simon Que <sque@ti.com>
|
|
* Hari Kanigeri <h-kanigeri2@ti.com>
|
|
* Ohad Ben-Cohen <ohad@wizery.com>
|
|
* Suman Anna <s-anna@ti.com>
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/device.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/io.h>
|
|
#include <linux/bitops.h>
|
|
#include <linux/pm_runtime.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/spinlock.h>
|
|
#include <linux/hwspinlock.h>
|
|
#include <linux/of.h>
|
|
#include <linux/platform_device.h>
|
|
|
|
#include "hwspinlock_internal.h"
|
|
|
|
/* Spinlock register offsets */
|
|
#define SYSSTATUS_OFFSET 0x0014
|
|
#define LOCK_BASE_OFFSET 0x0800
|
|
|
|
#define SPINLOCK_NUMLOCKS_BIT_OFFSET (24)
|
|
|
|
/* Possible values of SPINLOCK_LOCK_REG */
|
|
#define SPINLOCK_NOTTAKEN (0) /* free */
|
|
#define SPINLOCK_TAKEN (1) /* locked */
|
|
|
|
static int omap_hwspinlock_trylock(struct hwspinlock *lock)
|
|
{
|
|
void __iomem *lock_addr = lock->priv;
|
|
|
|
/* attempt to acquire the lock by reading its value */
|
|
return (SPINLOCK_NOTTAKEN == readl(lock_addr));
|
|
}
|
|
|
|
static void omap_hwspinlock_unlock(struct hwspinlock *lock)
|
|
{
|
|
void __iomem *lock_addr = lock->priv;
|
|
|
|
/* release the lock by writing 0 to it */
|
|
writel(SPINLOCK_NOTTAKEN, lock_addr);
|
|
}
|
|
|
|
/*
|
|
* relax the OMAP interconnect while spinning on it.
|
|
*
|
|
* The specs recommended that the retry delay time will be
|
|
* just over half of the time that a requester would be
|
|
* expected to hold the lock.
|
|
*
|
|
* The number below is taken from an hardware specs example,
|
|
* obviously it is somewhat arbitrary.
|
|
*/
|
|
static void omap_hwspinlock_relax(struct hwspinlock *lock)
|
|
{
|
|
ndelay(50);
|
|
}
|
|
|
|
static const struct hwspinlock_ops omap_hwspinlock_ops = {
|
|
.trylock = omap_hwspinlock_trylock,
|
|
.unlock = omap_hwspinlock_unlock,
|
|
.relax = omap_hwspinlock_relax,
|
|
};
|
|
|
|
static int omap_hwspinlock_probe(struct platform_device *pdev)
|
|
{
|
|
struct hwspinlock_device *bank;
|
|
void __iomem *io_base;
|
|
int num_locks, i, ret;
|
|
/* Only a single hwspinlock block device is supported */
|
|
int base_id = 0;
|
|
|
|
io_base = devm_platform_ioremap_resource(pdev, 0);
|
|
if (IS_ERR(io_base))
|
|
return PTR_ERR(io_base);
|
|
|
|
/*
|
|
* make sure the module is enabled and clocked before reading
|
|
* the module SYSSTATUS register
|
|
*/
|
|
devm_pm_runtime_enable(&pdev->dev);
|
|
ret = pm_runtime_resume_and_get(&pdev->dev);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Determine number of locks */
|
|
i = readl(io_base + SYSSTATUS_OFFSET);
|
|
i >>= SPINLOCK_NUMLOCKS_BIT_OFFSET;
|
|
|
|
/*
|
|
* runtime PM will make sure the clock of this module is
|
|
* enabled again iff at least one lock is requested
|
|
*/
|
|
ret = pm_runtime_put(&pdev->dev);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* one of the four lsb's must be set, and nothing else */
|
|
if (hweight_long(i & 0xf) != 1 || i > 8)
|
|
return -EINVAL;
|
|
|
|
num_locks = i * 32; /* actual number of locks in this device */
|
|
|
|
bank = devm_kzalloc(&pdev->dev, struct_size(bank, lock, num_locks),
|
|
GFP_KERNEL);
|
|
if (!bank)
|
|
return -ENOMEM;
|
|
|
|
for (i = 0; i < num_locks; i++)
|
|
bank->lock[i].priv = io_base + LOCK_BASE_OFFSET + sizeof(u32) * i;
|
|
|
|
return devm_hwspin_lock_register(&pdev->dev, bank, &omap_hwspinlock_ops,
|
|
base_id, num_locks);
|
|
}
|
|
|
|
static const struct of_device_id omap_hwspinlock_of_match[] = {
|
|
{ .compatible = "ti,omap4-hwspinlock", },
|
|
{ .compatible = "ti,am64-hwspinlock", },
|
|
{ .compatible = "ti,am654-hwspinlock", },
|
|
{ /* end */ },
|
|
};
|
|
MODULE_DEVICE_TABLE(of, omap_hwspinlock_of_match);
|
|
|
|
static struct platform_driver omap_hwspinlock_driver = {
|
|
.probe = omap_hwspinlock_probe,
|
|
.driver = {
|
|
.name = "omap_hwspinlock",
|
|
.of_match_table = omap_hwspinlock_of_match,
|
|
},
|
|
};
|
|
|
|
static int __init omap_hwspinlock_init(void)
|
|
{
|
|
return platform_driver_register(&omap_hwspinlock_driver);
|
|
}
|
|
/* board init code might need to reserve hwspinlocks for predefined purposes */
|
|
postcore_initcall(omap_hwspinlock_init);
|
|
|
|
static void __exit omap_hwspinlock_exit(void)
|
|
{
|
|
platform_driver_unregister(&omap_hwspinlock_driver);
|
|
}
|
|
module_exit(omap_hwspinlock_exit);
|
|
|
|
MODULE_LICENSE("GPL v2");
|
|
MODULE_DESCRIPTION("Hardware spinlock driver for OMAP");
|
|
MODULE_AUTHOR("Simon Que <sque@ti.com>");
|
|
MODULE_AUTHOR("Hari Kanigeri <h-kanigeri2@ti.com>");
|
|
MODULE_AUTHOR("Ohad Ben-Cohen <ohad@wizery.com>");
|