mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-09-21 12:11:49 +08:00
37bac77e46
Add a new HCI protocol HCI_UART_AML for the Amlogic Bluetooth controller. It works on the standard H4 protocol via a 4-wire UART interface, with baud rates up to 4 Mbps. The controller supports two types of commands: the TCI commands and the vendor command. The former is for initial setup including setting baud rates, downloading fw, starting chip and etc, while the latter is for dumping firmware versions and setting public address after firmware updates and normal startup. It was verified on board of T602 (S905X4 + W265S2). dmesg: .. [ 5.313450] Bluetooth: HCI UART protocol AML registered [ 6.506052] Bluetooth: hci0: fw_version: date = 42.28, number = 0xb2fd ... Co-developed-by: Ye He <ye.he@amlogic.com> Signed-off-by: Ye He <ye.he@amlogic.com> Signed-off-by: Yang Li <yang.li@amlogic.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
56 lines
1.8 KiB
Makefile
56 lines
1.8 KiB
Makefile
# SPDX-License-Identifier: GPL-2.0
|
|
#
|
|
# Makefile for the Linux Bluetooth HCI device drivers.
|
|
#
|
|
|
|
obj-$(CONFIG_BT_HCIVHCI) += hci_vhci.o
|
|
obj-$(CONFIG_BT_HCIUART) += hci_uart.o
|
|
obj-$(CONFIG_BT_HCIBCM203X) += bcm203x.o
|
|
obj-$(CONFIG_BT_HCIBCM4377) += hci_bcm4377.o
|
|
obj-$(CONFIG_BT_HCIBPA10X) += bpa10x.o
|
|
obj-$(CONFIG_BT_HCIBFUSB) += bfusb.o
|
|
obj-$(CONFIG_BT_HCIDTL1) += dtl1_cs.o
|
|
obj-$(CONFIG_BT_HCIBT3C) += bt3c_cs.o
|
|
obj-$(CONFIG_BT_HCIBLUECARD) += bluecard_cs.o
|
|
|
|
obj-$(CONFIG_BT_HCIBTUSB) += btusb.o
|
|
obj-$(CONFIG_BT_HCIBTSDIO) += btsdio.o
|
|
|
|
obj-$(CONFIG_BT_INTEL) += btintel.o
|
|
obj-$(CONFIG_BT_INTEL_PCIE) += btintel_pcie.o btintel.o
|
|
obj-$(CONFIG_BT_ATH3K) += ath3k.o
|
|
obj-$(CONFIG_BT_MRVL) += btmrvl.o
|
|
obj-$(CONFIG_BT_MRVL_SDIO) += btmrvl_sdio.o
|
|
obj-$(CONFIG_BT_MTKSDIO) += btmtksdio.o
|
|
obj-$(CONFIG_BT_MTKUART) += btmtkuart.o
|
|
obj-$(CONFIG_BT_QCOMSMD) += btqcomsmd.o
|
|
obj-$(CONFIG_BT_BCM) += btbcm.o
|
|
obj-$(CONFIG_BT_RTL) += btrtl.o
|
|
obj-$(CONFIG_BT_QCA) += btqca.o
|
|
obj-$(CONFIG_BT_MTK) += btmtk.o
|
|
|
|
obj-$(CONFIG_BT_VIRTIO) += virtio_bt.o
|
|
obj-$(CONFIG_BT_NXPUART) += btnxpuart.o
|
|
|
|
obj-$(CONFIG_BT_HCIUART_NOKIA) += hci_nokia.o
|
|
|
|
obj-$(CONFIG_BT_HCIRSI) += btrsi.o
|
|
|
|
btmrvl-y := btmrvl_main.o
|
|
btmrvl-$(CONFIG_DEBUG_FS) += btmrvl_debugfs.o
|
|
|
|
hci_uart-y := hci_ldisc.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_SERDEV) += hci_serdev.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_H4) += hci_h4.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_BCSP) += hci_bcsp.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_LL) += hci_ll.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_ATH3K) += hci_ath.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_3WIRE) += hci_h5.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_INTEL) += hci_intel.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_BCM) += hci_bcm.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_QCA) += hci_qca.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_AG6XX) += hci_ag6xx.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_MRVL) += hci_mrvl.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_AML) += hci_aml.o
|
|
hci_uart-objs := $(hci_uart-y)
|