mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-14 07:44:21 +08:00
d5862720c0
Add dt bindings for Marvell AC5/X/IM eMMC controller. This compatibility string covers the differences in the AC5/X version of the driver: 31-bit bus limitation and DDR memory starting at address 0x2_0000_0000, which are handled by usage of a bounce buffer plus a different DMA mask. Signed-off-by: Elad Nachman <enachman@marvell.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240103172803.1826113-2-enachman@marvell.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
280 lines
7.8 KiB
YAML
280 lines
7.8 KiB
YAML
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: Marvell Xenon SDHCI Controller
|
|
|
|
description: |
|
|
This file documents differences between the core MMC properties described by
|
|
mmc-controller.yaml and the properties used by the Xenon implementation.
|
|
|
|
Multiple SDHCs might be put into a single Xenon IP, to save size and cost.
|
|
Each SDHC is independent and owns independent resources, such as register
|
|
sets, clock and PHY.
|
|
|
|
Each SDHC should have an independent device tree node.
|
|
|
|
maintainers:
|
|
- Ulf Hansson <ulf.hansson@linaro.org>
|
|
|
|
properties:
|
|
compatible:
|
|
oneOf:
|
|
- enum:
|
|
- marvell,armada-cp110-sdhci
|
|
- marvell,armada-ap806-sdhci
|
|
|
|
- items:
|
|
- enum:
|
|
- marvell,armada-ap807-sdhci
|
|
- marvell,ac5-sdhci
|
|
- const: marvell,armada-ap806-sdhci
|
|
|
|
- items:
|
|
- const: marvell,armada-3700-sdhci
|
|
- const: marvell,sdhci-xenon
|
|
|
|
reg:
|
|
minItems: 1
|
|
maxItems: 2
|
|
description: |
|
|
For "marvell,armada-3700-sdhci", two register areas. The first one
|
|
for Xenon IP register. The second one for the Armada 3700 SoC PHY PAD
|
|
Voltage Control register. Please follow the examples with compatible
|
|
"marvell,armada-3700-sdhci" in below.
|
|
Please also check property marvell,pad-type in below.
|
|
|
|
For other compatible strings, one register area for Xenon IP.
|
|
|
|
clocks:
|
|
minItems: 1
|
|
maxItems: 2
|
|
|
|
clock-names:
|
|
minItems: 1
|
|
items:
|
|
- const: core
|
|
- const: axi
|
|
|
|
interrupts:
|
|
maxItems: 1
|
|
|
|
marvell,xenon-sdhc-id:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 0
|
|
maximum: 7
|
|
description: |
|
|
Indicate the corresponding bit index of current SDHC in SDHC System
|
|
Operation Control Register Bit[7:0]. Set/clear the corresponding bit to
|
|
enable/disable current SDHC.
|
|
|
|
marvell,xenon-phy-type:
|
|
$ref: /schemas/types.yaml#/definitions/string
|
|
enum:
|
|
- emmc 5.1 phy
|
|
- emmc 5.0 phy
|
|
description: |
|
|
Xenon support multiple types of PHYs. To select eMMC 5.1 PHY, set:
|
|
marvell,xenon-phy-type = "emmc 5.1 phy" eMMC 5.1 PHY is the default
|
|
choice if this property is not provided. To select eMMC 5.0 PHY, set:
|
|
marvell,xenon-phy-type = "emmc 5.0 phy"
|
|
|
|
All those types of PHYs can support eMMC, SD and SDIO. Please note that
|
|
this property only presents the type of PHY. It doesn't stand for the
|
|
entire SDHC type or property. For example, "emmc 5.1 phy" doesn't mean
|
|
that this Xenon SDHC only supports eMMC 5.1.
|
|
|
|
marvell,xenon-phy-znr:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 0
|
|
maximum: 0x1f
|
|
default: 0xf
|
|
description: |
|
|
Set PHY ZNR value.
|
|
Only available for eMMC PHY.
|
|
|
|
marvell,xenon-phy-zpr:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 0
|
|
maximum: 0x1f
|
|
default: 0xf
|
|
description: |
|
|
Set PHY ZPR value.
|
|
Only available for eMMC PHY.
|
|
|
|
marvell,xenon-phy-nr-success-tun:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 1
|
|
maximum: 7
|
|
default: 0x4
|
|
description: |
|
|
Set the number of required consecutive successful sampling points
|
|
used to identify a valid sampling window, in tuning process.
|
|
|
|
marvell,xenon-phy-tun-step-divider:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
default: 64
|
|
description: |
|
|
Set the divider for calculating TUN_STEP.
|
|
|
|
marvell,xenon-phy-slow-mode:
|
|
type: boolean
|
|
description: |
|
|
If this property is selected, transfers will bypass PHY.
|
|
Only available when bus frequency lower than 55MHz in SDR mode.
|
|
Disabled by default. Please only try this property if timing issues
|
|
always occur with PHY enabled in eMMC HS SDR, SD SDR12, SD SDR25,
|
|
SD Default Speed and HS mode and eMMC legacy speed mode.
|
|
|
|
marvell,xenon-tun-count:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
default: 0x9
|
|
description: |
|
|
Xenon SDHC SoC usually doesn't provide re-tuning counter in
|
|
Capabilities Register 3 Bit[11:8].
|
|
This property provides the re-tuning counter.
|
|
|
|
allOf:
|
|
- $ref: mmc-controller.yaml#
|
|
- if:
|
|
properties:
|
|
compatible:
|
|
contains:
|
|
const: marvell,armada-3700-sdhci
|
|
|
|
then:
|
|
properties:
|
|
reg:
|
|
items:
|
|
- description: Xenon IP registers
|
|
- description: Armada 3700 SoC PHY PAD Voltage Control register
|
|
|
|
marvell,pad-type:
|
|
$ref: /schemas/types.yaml#/definitions/string
|
|
enum:
|
|
- sd
|
|
- fixed-1-8v
|
|
description: |
|
|
Type of Armada 3700 SoC PHY PAD Voltage Controller register.
|
|
If "sd" is selected, SoC PHY PAD is set as 3.3V at the beginning
|
|
and is switched to 1.8V when later in higher speed mode.
|
|
If "fixed-1-8v" is selected, SoC PHY PAD is fixed 1.8V, such as for
|
|
eMMC.
|
|
Please follow the examples with compatible
|
|
"marvell,armada-3700-sdhci" in below.
|
|
|
|
required:
|
|
- marvell,pad-type
|
|
|
|
- if:
|
|
properties:
|
|
compatible:
|
|
contains:
|
|
enum:
|
|
- marvell,armada-cp110-sdhci
|
|
- marvell,armada-ap807-sdhci
|
|
- marvell,armada-ap806-sdhci
|
|
|
|
then:
|
|
properties:
|
|
clocks:
|
|
minItems: 2
|
|
|
|
clock-names:
|
|
items:
|
|
- const: core
|
|
- const: axi
|
|
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- clocks
|
|
- clock-names
|
|
|
|
unevaluatedProperties: false
|
|
|
|
examples:
|
|
- |
|
|
// For eMMC
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
|
mmc@aa0000 {
|
|
compatible = "marvell,armada-ap807-sdhci", "marvell,armada-ap806-sdhci";
|
|
reg = <0xaa0000 0x1000>;
|
|
interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&emmc_clk 0>, <&axi_clk 0>;
|
|
clock-names = "core", "axi";
|
|
bus-width = <4>;
|
|
marvell,xenon-phy-slow-mode;
|
|
marvell,xenon-tun-count = <11>;
|
|
non-removable;
|
|
no-sd;
|
|
no-sdio;
|
|
|
|
/* Vmmc and Vqmmc are both fixed */
|
|
};
|
|
|
|
- |
|
|
// For SD/SDIO
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
|
mmc@ab0000 {
|
|
compatible = "marvell,armada-cp110-sdhci";
|
|
reg = <0xab0000 0x1000>;
|
|
interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
|
|
vqmmc-supply = <&sd_vqmmc_regulator>;
|
|
vmmc-supply = <&sd_vmmc_regulator>;
|
|
clocks = <&sdclk 0>, <&axi_clk 0>;
|
|
clock-names = "core", "axi";
|
|
bus-width = <4>;
|
|
marvell,xenon-tun-count = <9>;
|
|
};
|
|
|
|
- |
|
|
// For eMMC with compatible "marvell,armada-3700-sdhci":
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
|
mmc@aa0000 {
|
|
compatible = "marvell,armada-3700-sdhci", "marvell,sdhci-xenon";
|
|
reg = <0xaa0000 0x1000>,
|
|
<0x17808 0x4>;
|
|
interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&emmcclk 0>;
|
|
clock-names = "core";
|
|
bus-width = <8>;
|
|
mmc-ddr-1_8v;
|
|
mmc-hs400-1_8v;
|
|
non-removable;
|
|
no-sd;
|
|
no-sdio;
|
|
|
|
/* Vmmc and Vqmmc are both fixed */
|
|
|
|
marvell,pad-type = "fixed-1-8v";
|
|
};
|
|
|
|
- |
|
|
// For SD/SDIO with compatible "marvell,armada-3700-sdhci":
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
|
mmc@ab0000 {
|
|
compatible = "marvell,armada-3700-sdhci", "marvell,sdhci-xenon";
|
|
reg = <0xab0000 0x1000>,
|
|
<0x17808 0x4>;
|
|
interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
|
|
vqmmc-supply = <&sd_regulator>;
|
|
/* Vmmc is fixed */
|
|
clocks = <&sdclk 0>;
|
|
clock-names = "core";
|
|
bus-width = <4>;
|
|
|
|
marvell,pad-type = "sd";
|
|
};
|