Any return value from gpiod_get_optional() other than a pointer to a
GPIO descriptor or a NULL-pointer is an error and the driver should
abort probing. That being said: commit 56d074d26c ("Bluetooth: hci_qca:
don't use IS_ERR_OR_NULL() with gpiod_get_optional()") no longer sets
power_ctrl_enabled on NULL-pointer returned by
devm_gpiod_get_optional(). Restore this behavior but bail-out on errors.
While at it: also bail-out on error returned when trying to get the
"swctrl" GPIO.
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Zijun Hu <quic_zijuhu@quicinc.com>
Closes: https://lore.kernel.org/linux-bluetooth/1713449192-25926-2-git-send-email-quic_zijuhu@quicinc.com/
Fixes: 56d074d26c ("Bluetooth: hci_qca: don't use IS_ERR_OR_NULL() with gpiod_get_optional()")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Wren Turkal" <wt@penguintechs.org>
Reported-by: Wren Turkal <wt@penguintechs.org>
Reported-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Krzysztof Kozlowski<krzysztof.kozlowski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Qualcomm ROME controllers can be registered from the Bluetooth line
discipline and in this case the HCI UART serdev pointer is NULL.
Add the missing sanity check to prevent a NULL-pointer dereference when
setup() is called for a non-serdev controller.
Fixes: e9b3e5b8c6 ("Bluetooth: hci_qca: only assign wakeup with serial port support")
Cc: stable@vger.kernel.org # 6.2
Cc: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Qualcomm ROME controllers can be registered from the Bluetooth line
discipline and in this case the HCI UART serdev pointer is NULL.
Add the missing sanity check to prevent a NULL-pointer dereference when
wakeup() is called for a non-serdev controller during suspend.
Just return true for now to restore the original behaviour and address
the crash with pre-6.2 kernels, which do not have commit e9b3e5b8c6
("Bluetooth: hci_qca: only assign wakeup with serial port support") that
causes the crash to happen already at setup() time.
Fixes: c1a74160ea ("Bluetooth: hci_qca: Add device_may_wakeup support")
Cc: stable@vger.kernel.org # 5.13
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_devcd_append() would free the skb on error so the caller don't
have to free it again otherwise it would cause the double free of skb.
Fixes: 0b70151328 ("Bluetooth: btusb: mediatek: add MediaTek devcoredump support")
Reported-by : Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Qualcomm Bluetooth controllers may not have been provisioned with a
valid device address and instead end up using the default address
00:00:00:00:5a:ad.
This was previously believed to be due to lack of persistent storage for
the address but it may also be due to integrators opting to not use the
on-chip OTP memory and instead store the address elsewhere (e.g. in
storage managed by secure world firmware).
According to Qualcomm, at least WCN6750, WCN6855 and WCN7850 have
on-chip OTP storage for the address.
As the device type alone cannot be used to determine when the address is
valid, instead read back the address during setup() and only set the
HCI_QUIRK_USE_BDADDR_PROPERTY flag when needed.
This specifically makes sure that controllers that have been provisioned
with an address do not start as unconfigured.
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Link: https://lore.kernel.org/r/124a7d54-5a18-4be7-9a76-a12017f6cce5@quicinc.com/
Fixes: 5971752de4 ("Bluetooth: hci_qca: Set HCI_QUIRK_USE_BDADDR_PROPERTY for wcn3990")
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Fixes: 6945795bc8 ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org # 6.5
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btusb_coredump_qca() uses __hci_cmd_sync() to send a vendor-specific
command to trigger firmware coredump, but the command does not
have any event as its sync response, so it is not suitable to use
__hci_cmd_sync(), fixed by using __hci_cmd_send().
Fixes: 20981ce2d5 ("Bluetooth: btusb: Add WCN6855 devcoredump support")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The WCN6855 firmware on the Lenovo ThinkPad X13s expects the Bluetooth
device address in big-endian order when setting it using the
EDL_WRITE_BD_ADDR_OPCODE command.
Presumably, this is the case for all non-ROME devices which all use the
EDL_WRITE_BD_ADDR_OPCODE command for this (unlike the ROME devices which
use a different command and expect the address in little-endian order).
Reverse the little-endian address before setting it to make sure that
the address can be configured using tools like btmgmt or using the
'local-bd-address' devicetree property.
Note that this can potentially break systems with boot firmware which
has started relying on the broken behaviour and is incorrectly passing
the address via devicetree in big-endian order.
The only device affected by this should be the WCN3991 used in some
Chromebooks. As ChromeOS updates the kernel and devicetree in lockstep,
the new 'qcom,local-bd-address-broken' property can be used to determine
if the firmware is buggy so that the underlying driver bug can be fixed
without breaking backwards compatibility.
Set the HCI_QUIRK_BDADDR_PROPERTY_BROKEN quirk for such platforms so
that the address is reversed when parsing the address property.
Fixes: 5c0a1001c8 ("Bluetooth: hci_qca: Add helper to set device address")
Cc: stable@vger.kernel.org # 5.1
Cc: Balakrishna Godavarthi <quic_bgodavar@quicinc.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Nikita Travkin <nikita@trvn.ru> # sc7180
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts commit 7dcd3e014a.
Qualcomm Bluetooth controllers like WCN6855 do not have persistent
storage for the Bluetooth address and must therefore start as
unconfigured to allow the user to set a valid address unless one has
been provided by the boot firmware in the devicetree.
A recent change snuck into v6.8-rc7 and incorrectly started marking the
default (non-unique) address as valid. This specifically also breaks the
Bluetooth setup for some user of the Lenovo ThinkPad X13s.
Note that this is the second time Qualcomm breaks the driver this way
and that this was fixed last year by commit 6945795bc8 ("Bluetooth:
fix use-bdaddr-property quirk"), which also has some further details.
Fixes: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Cc: stable@vger.kernel.org # 6.8
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Clayton Craft <clayton@craftyguy.net>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Here is the big set of TTY/Serial driver updates and cleanups for
6.9-rc1. Included in here are:
- more tty cleanups from Jiri
- loads of 8250 driver cleanups from Andy
- max310x driver updates
- samsung serial driver updates
- uart_prepare_sysrq_char() updates for many drivers
- platform driver remove callback void cleanups
- stm32 driver updates
- other small tty/serial driver updates
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZfwqow8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNegCffxTbsnbMGjWhVrQ326IJx/DFvNMAoI9csigv
m+G3RzefzZLRx8nAma0c
=GMfc
-----END PGP SIGNATURE-----
Merge tag 'tty-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of TTY/Serial driver updates and cleanups for
6.9-rc1. Included in here are:
- more tty cleanups from Jiri
- loads of 8250 driver cleanups from Andy
- max310x driver updates
- samsung serial driver updates
- uart_prepare_sysrq_char() updates for many drivers
- platform driver remove callback void cleanups
- stm32 driver updates
- other small tty/serial driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'tty-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
dt-bindings: serial: stm32: add power-domains property
serial: 8250_dw: Replace ACPI device check by a quirk
serial: Lock console when calling into driver before registration
serial: 8250_uniphier: Switch to use uart_read_port_properties()
serial: 8250_tegra: Switch to use uart_read_port_properties()
serial: 8250_pxa: Switch to use uart_read_port_properties()
serial: 8250_omap: Switch to use uart_read_port_properties()
serial: 8250_of: Switch to use uart_read_port_properties()
serial: 8250_lpc18xx: Switch to use uart_read_port_properties()
serial: 8250_ingenic: Switch to use uart_read_port_properties()
serial: 8250_dw: Switch to use uart_read_port_properties()
serial: 8250_bcm7271: Switch to use uart_read_port_properties()
serial: 8250_bcm2835aux: Switch to use uart_read_port_properties()
serial: 8250_aspeed_vuart: Switch to use uart_read_port_properties()
serial: port: Introduce a common helper to read properties
serial: core: Add UPIO_UNKNOWN constant for unknown port type
serial: core: Move struct uart_port::quirks closer to possible values
serial: sh-sci: Call sci_serial_{in,out}() directly
serial: core: only stop transmit when HW fifo is empty
serial: pch: Use uart_prepare_sysrq_char().
...
The ATS2851 controller erroneously reports support for the "Read
Encryption Key Length" HCI command. This makes it unable to connect
to any devices, since this command is issued by the kernel during the
connection process in response to an "Encryption Change" HCI event.
Add a new quirk (HCI_QUIRK_BROKEN_ENC_KEY_SIZE) to hint that the command
is unsupported, preventing it from interrupting the connection process.
This is the error log from btmon before this patch:
> HCI Event: Encryption Change (0x08) plen 4
Status: Success (0x00)
Handle: 2048 Address: ...
Encryption: Enabled with E0 (0x01)
< HCI Command: Read Encryption Key Size (0x05|0x0008) plen 2
Handle: 2048 Address: ...
> HCI Event: Command Status (0x0f) plen 4
Read Encryption Key Size (0x05|0x0008) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Vinicius Peixoto <nukelet64@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since dracut refers to the module info for defining the required
firmware files and btmtk driver doesn't provide the firmware info for
MT7922, the generate initrd misses the firmware, resulting in the
broken Bluetooth.
This patch simply adds the MODULE_FIRMWARE() for the missing entry
for covering that.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1214133
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This checks if CONFIG_DEV_COREDUMP is enabled before attempting to clone
the skb and also make sure btmtk_process_coredump frees the skb passed
following the same logic.
Fixes: 0b70151328 ("Bluetooth: btusb: mediatek: add MediaTek devcoredump support")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In some cases uart-base drivers may need to use priv data. For
example, to store information needed for devcoredump.
Fixes: 044014ce85 ("Bluetooth: btrtl: Add Realtek devcoredump support")
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the following build regression:
drivers-bluetooth-btintel.c-btintel_read_version()-warn:
passing-zero-to-PTR_ERR
Fixes: b79e040910 ("Bluetooth: btintel: Fix null ptr deref in btintel_read_version")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The optional variants for the gpiod_get() family of functions return NULL
if the GPIO in question is not associated with this device. They return
ERR_PTR() on any other error. NULL descriptors are graciously handled by
GPIOLIB and can be safely passed to any of the GPIO consumer interfaces
as they will return 0 and act as if the function succeeded. If one is
using the optional variant, then there's no point in checking for NULL.
Fixes: 6845667146 ("Bluetooth: hci_qca: Fix NULL vs IS_ERR_OR_NULL check in qca_serdev_probe")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Firmware sequencer (FSEQ) is a common code shared across Bluetooth
and Wifi. Printing FSEQ will help to debug if there is any mismatch
between Bluetooth and Wifi FSEQ.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use devm_kstrdup() instead of hand-writing it.
It is less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use strreplace() instead of hand-writing it.
It is less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If hci_cmd_sync_complete() is triggered and skb is NULL, then
hdev->req_skb is NULL, which will cause this issue.
Reported-and-tested-by: syzbot+830d9e3fa61968246abd@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the tx timeout issue seen while running a stress test on
btnxpuart for couple of hours, such that the interval between two HCI
commands coincide with the power save timeout value of 2 seconds.
Test procedure using bash script:
<load btnxpuart.ko>
hciconfig hci0 up
//Enable Power Save feature
hcitool -i hci0 cmd 3f 23 02 00 00
while (true)
do
hciconfig hci0 leadv
sleep 2
hciconfig hci0 noleadv
sleep 2
done
Error log, after adding few more debug prints:
Bluetooth: btnxpuart_queue_skb(): 01 0A 20 01 00
Bluetooth: hci0: Set UART break: on, status=0
Bluetooth: hci0: btnxpuart_tx_wakeup() tx_work scheduled
Bluetooth: hci0: btnxpuart_tx_work() dequeue: 01 0A 20 01 00
Can't set advertise mode on hci0: Connection timed out (110)
Bluetooth: hci0: command 0x200a tx timeout
When the power save mechanism turns on UART break, and btnxpuart_tx_work()
is scheduled simultaneously, psdata->ps_state is read as PS_STATE_AWAKE,
which prevents the psdata->work from being scheduled, which is responsible
to turn OFF UART break.
This issue is fixed by adding a ps_lock mutex around UART break on/off as
well as around ps_state read/write.
btnxpuart_tx_wakeup() will now read updated ps_state value. If ps_state is
PS_STATE_SLEEP, it will first schedule psdata->work, and then it will
reschedule itself once UART break has been turned off and ps_state is
PS_STATE_AWAKE.
Tested above script for 50,000 iterations and TX timeout error was not
observed anymore.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_coredump_qca() uses __hci_cmd_sync() to send a vendor-specific command
to trigger firmware coredump, but the command does not have any event as
its sync response, so it is not suitable to use __hci_cmd_sync(), fixed by
using __hci_cmd_send().
Fixes: 06d3fdfcdf ("Bluetooth: hci_qca: Add qcom devcoredump support")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BT adapter going into UNCONFIGURED state during BT turn ON when
devicetree has no local-bd-address node.
Bluetooth will not work out of the box on such devices, to avoid this
problem, added check to set HCI_QUIRK_USE_BDADDR_PROPERTY based on
local-bd-address node entry.
When this quirk is not set, the public Bluetooth address read by host
from controller though HCI Read BD Address command is
considered as valid.
Fixes: e668eb1e15 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A recent commit restored the original (and still documented) semantics
for the HCI_QUIRK_USE_BDADDR_PROPERTY quirk so that the device address
is considered invalid unless an address is provided by firmware.
This specifically means that this flag must only be set for devices with
invalid addresses, but the Broadcom BCM4377 driver has so far been
setting this flag unconditionally.
Fortunately the driver already checks for invalid addresses during setup
and sets the HCI_QUIRK_INVALID_BDADDR flag, which can simply be replaced
with HCI_QUIRK_USE_BDADDR_PROPERTY to indicate that the default address
is invalid but can be overridden by firmware (long term, this should
probably just always be allowed).
Fixes: 6945795bc8 ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org # 6.5
Reported-by: Felix Zhang <mrman@mrman314.tech>
Link: https://lore.kernel.org/r/77419ffacc5b4875e920e038332575a2a5bff29f.camel@mrman314.tech/
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Felix Zhang <mrman@mrman314.tech>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
receive_buf() is called from ttyport_receive_buf() that expects values
">= 0" from serdev_controller_receive_buf(), change its return type from
ssize_t to size_t.
The need for this clean-up was noticed while fixing a warning, see
commit 94d0539425 ("Bluetooth: btnxpuart: fix recv_buf() return value").
Changing the callback prototype to return an unsigned seems the best way
to document the API and ensure that is properly used.
GNSS drivers implementation of serdev receive_buf() callback return
directly the return value of gnss_insert_raw(). gnss_insert_raw()
returns a signed int, however this is not an issue since the value
returned is always positive, because of the kfifo_in() implementation.
gnss_insert_raw() could be changed to return also an unsigned, however
this is not implemented here as request by the GNSS maintainer Johan
Hovold.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/all/087be419-ec6b-47ad-851a-5e1e3ea5cfcc@kernel.org/
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Reviewed-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Acked-by: Maximilian Luz <luzmaximilian@gmail.com> # for platform/surface
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240122180551.34429-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaedng8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yndHACfX3SA2ipK5umpMsWOoLMCBV6VyrwAn3t+FPd/
z4mNiCuNUhbEnU7RinK0
=k/E9
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty core
and drivers in here, along with the usual set of rs485 updates (someday
this might work properly...) Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaeUaw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykyOgCgp1uhP/b9iW6qM7qL6OYEG6idI0kAnj0VASNm
vSI69HmdKKwo69YLOSBp
=14n1
-----END PGP SIGNATURE-----
Merge tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty
core and drivers in here, along with the usual set of rs485 updates
(someday this might work properly...)
Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (197 commits)
serial: sc16is7xx: refactor EFR lock
serial: sc16is7xx: reorder code to remove prototype declarations
serial: sc16is7xx: refactor FIFO access functions to increase commonality
serial: sc16is7xx: drop unneeded MODULE_ALIAS
serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
serial: sc16is7xx: add explicit return for some switch default cases
serial: sc16is7xx: add macro for max number of UART ports
serial: sc16is7xx: add driver name to struct uart_driver
serial: sc16is7xx: use i2c_get_match_data()
serial: sc16is7xx: use spi_get_device_match_data()
serial: sc16is7xx: use DECLARE_BITMAP for sc16is7xx_lines bitfield
serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()
serial: sc16is7xx: remove obsolete loop in sc16is7xx_port_irq()
serial: sc16is7xx: set safe default SPI clock frequency
serial: sc16is7xx: add check for unsupported SPI modes during probe
serial: sc16is7xx: fix invalid sc16is7xx_lines bitfield in case of probe error
serial: 8250_exar: Set missing rs485_supported flag
serial: omap: do not override settings for RS485 support
serial: core, imx: do not set RS485 enabled if it is not supported
serial: core: make sure RS485 cannot be enabled when it is not supported
...
There is usbdrv_wrap in struct usb_driver and usb_device_driver, it
contains device_driver and for_devices. for_devices is used to
distinguish between device drivers and interface drivers.
Like the is_usb_device(), it tests the type of the device. We can test
that if the probe of device_driver is equal to usb_probe_device in
is_usb_device_driver(), and then the struct usbdrv_wrap is no longer
needed.
Clean up struct usbdrv_wrap, use device_driver directly in struct
usb_driver and usb_device_driver. This makes the code cleaner.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240104032822.1896596-1-yajun.deng@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove useless assignment of rx_skb to NULL in case the skb is in error,
this is already done in h4_recv_buf() that is executed a few lines
before.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Serdev recv_buf() callback is supposed to return the amount of bytes
consumed, therefore an int in between 0 and count.
Do not return negative number in case of issue, just print an error and
return count. This fixes a WARN in ttyport_receive_buf().
Link: https://lore.kernel.org/all/087be419-ec6b-47ad-851a-5e1e3ea5cfcc@kernel.org/
Fixes: 7237c4c9ec ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Serdev recv_buf() callback is supposed to return the amount of bytes
consumed, therefore an int in between 0 and count.
Do not return a negative number in case of issue, just print an error
and return count. Before this change, in case of error, the returned
negative number was internally converted to 0 in ttyport_receive_buf,
now when the receive buffer is corrupted we return the size of the whole
received data (`count`). This should allow for better recovery in case
receiver/transmitter get out of sync if some data is lost.
This fixes a WARN in ttyport_receive_buf().
Bluetooth: hci0: Frame reassembly failed (-84)
------------[ cut here ]------------
serial serial0: receive_buf returns -84 (count = 6)
WARNING: CPU: 0 PID: 37 at drivers/tty/serdev/serdev-ttyport.c:37 ttyport_receive_buf+0xd8/0xf8
Modules linked in: mwifiex_sdio(+) ...
CPU: 0 PID: 37 Comm: kworker/u4:2 Not tainted 6.7.0-rc2-00147-gf1a09972a45a #1
Hardware name: Toradex Verdin AM62 WB on Verdin Development Board (DT)
Workqueue: events_unbound flush_to_ldisc
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ttyport_receive_buf+0xd8/0xf8
lr : ttyport_receive_buf+0xd8/0xf8
...
Call trace:
ttyport_receive_buf+0xd8/0xf8
flush_to_ldisc+0xbc/0x1a4
process_scheduled_works+0x16c/0x28c
Closes: https://lore.kernel.org/all/ZWEIhcUXfutb5SY6@francesco-nb.int.toradex.com/
Fixes: 689ca16e52 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For QCA2066 HFP offload, HCI_Configure_Data_Path is not required since
present HCI_Enhanced_Setup_Synchronous_Connection is enough to configure
non-HCI data transport path when set both Input_Data_Path and
Output_Data_Path parameters as 0x01, as is implemented by this change.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Intel Read Version event contains a TLV(0x32) having firmware sha1 in
operational image.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This checks if there are connections before suspending since that may
disrupt the connections making it stop receiving any data if remote
wakeup is not enabled.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Set both WIDEBAND_SPEECH_SUPPORTED and VALID_LE_STATES quirks
for QCA2066.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Switch character types to u8 and sizes to size_t. To conform to
characters/sizes in the rest of the tty layer.
This patch converts struct serdev_device_ops hooks and its
instantiations.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20231206073712.17776-24-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BTMTKSDIO_BT_WAKE_ENABLED flag is set for bluetooth interrupt
during system suspend and increases wakeup count for bluetooth event.
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch adds support for QCA2066 firmware patch and NVM downloading.
as the RF performance of QCA2066 SOC chip from different foundries may
vary. Therefore we use different NVM to configure them based on board ID.
Changes in v2
- optimize the function qca_generate_hsp_nvm_name
- remove redundant debug code for function qca_read_fw_board_id
Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
