We do not need it anymore since cfg80211 tracks
monitor channel and monitor channel type.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use cfg80211 the new .set_monitor_enabled instead
of tracking it inside mac80211.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This and ieee80211_add_ext_srates_ie() aren't
exported, so can't be used by drivers anyway,
but there's also no reason that they should be
so make them private to mac80211 and use sdata
instead of vif arguments.
Acked-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get current rssi (in dBm) from the driver/FW.
Instead of reporting the signal received in the last
rx packet, which might be inaccurate if rx traffic is
low and beacon filtering is enabled, get the signal
from the driver/FW.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a remain-on-channel item is deleted, we remove it
from the list and then start the next item. However,
if it wasn't actually the first item then calling
ieee80211_start_next_roc() is wrong as it will start
the first item -- even if that was already started.
Fix the two places that do this and add a warning to
prevent the problem from reoccurring.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Track userspace registrations for authentication
frames received on an IBSS interface. This field
will be used to decide whether or not to send
"open system" authentication frames when a new
station joins an adhoc network.
Signed-off-by: Will Hawkins <hawkinsw@opentechinstitute.org>
[redesign the code flow a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes the wrong assignment of mesh element TTL.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As defined in section 13.10.9.3 Case D (802.11-2012), this
control variable is used to limit the mesh STA to send only
one PREQ to a root mesh STA within this interval of time
(in TUs). The default value for this variable is set to
2000 TUs. However, for current implementation, the maximum
configurable of dot11MeshHWMPconfirmationInterval is
restricted by dot11MeshHWMPactivePathTimeout.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mesh_path_root_timer is invoked once the dot11MeshHWMPRootMode
is larger than 1. This patch also adds the backward compatible
to the previous setting on dot11MeshHWMPRootMode. If the user
configures as follow, it will still trigger the proactive RANN
with Gate Announcement.
iw mesh0 set mesh_param mesh_hwmp_rootmode 1
iw mesh0 set mesh_param mesh_gate_announcements 1
similar to the following setting:
iw mesh0 set mesh_param mesh_hwmp_rootmode 4
iw mesh0 set mesh_param mesh_gate_announcements 1
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the mesh configuration parameters dot11MeshHWMProotInterval
and dot11MeshHWMPactivePathToRootTimeout to be used by
proactive PREQ mechanism.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If you add a monitor interface in parallel to a normal interface
mac80211 will let you to change the channel type on the monitor
interface even if you are connected. Add an explicit check to
disallow this.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
[fix typo in commit log, use sdata instead of netdev]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise, we might call the driver callback before
the interface was uploaded.
Solves the following warning:
WARNING: at net/mac80211/driver-ops.h:12 ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]()
wlan0: Failed check-sdata-in-driver check, flags: 0x0
Modules linked in: wlcore_sdio wl12xx wl18xx wlcore mac80211 cfg80211 [last unloaded: cfg80211]
[<c001b964>] (unwind_backtrace+0x0/0x12c) from [<c0495550>] (dump_stack+0x20/0x24)
[<c0495550>] (dump_stack+0x20/0x24) from [<c003ee28>] (warn_slowpath_common+0x5c/0x74)
[<c003ee28>] (warn_slowpath_common+0x5c/0x74) from [<c003eefc>] (warn_slowpath_fmt+0x40/0x48)
[<c003eefc>] (warn_slowpath_fmt+0x40/0x48) from [<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211])
[<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]) from [<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211])
[<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211]) from [<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8)
[<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8) from [<c03e9164>] (netlink_rcv_skb+0x5c/0xc0)
[<c03e9164>] (netlink_rcv_skb+0x5c/0xc0) from [<c03e9ce0>] (genl_rcv+0x28/0x34)
[<c03e9ce0>] (genl_rcv+0x28/0x34) from [<c03e8e74>] (netlink_unicast+0x158/0x234)
[<c03e8e74>] (netlink_unicast+0x158/0x234) from [<c03e93e0>] (netlink_sendmsg+0x218/0x298)
[<c03e93e0>] (netlink_sendmsg+0x218/0x298) from [<c03b4e5c>] (sock_sendmsg+0xa4/0xc0)
[<c03b4e5c>] (sock_sendmsg+0xa4/0xc0) from [<c03b5af4>] (__sys_sendmsg+0x1d8/0x254)
[<c03b5af4>] (__sys_sendmsg+0x1d8/0x254) from [<c03b5ca8>] (sys_sendmsg+0x4c/0x70)
[<c03b5ca8>] (sys_sendmsg+0x4c/0x70) from [<c0013980>] (ret_fast_syscall+0x0/0x3c)
Note that calling the driver can also result
in undefined behaviour since it doesn't have
to deal with calls while down.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[removed timestamps, added note - Johannes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In my redesign of remain-on-channel I forgot
that an item could be cancelled when it's a
dependent item that is part of another item.
Allow cancelling such items by removing them
from the dependents list.
Note that when we cancel the main item, all
its dependents are also cancelled. It would
be possible to not do that, but would need
tricks to promote an item from dependent to
top-level and is tricky in the HW ROC case.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan pointed out to me that ieee80211_start_next_roc()
already calls ieee80211_run_deferred_scan() if the list
of ROC items is empty, so there's no need to call it
again after calling ieee80211_start_next_roc().
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
fix the coding style related to mesh parameters, especially the indentation,
as pointed out by Johannes Berg.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.
This fixes a number of small issues with the ROC
implementation:
* offloaded remain-on-channel couldn't be queued,
now we can queue it as well, if needed
* in iwlwifi (the only user) offloaded ROC is
mutually exclusive with scanning, use the new
queue to handle that case -- I expect that it
will later depend on a HW flag
The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.
The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.
Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IDLE handling in HW off-channel is broken right
now since we turn off IDLE only when the off-channel
period already started. Therefore, all drivers that
use it today (only iwlwifi!) must support off-channel
while idle, so playing with idle isn't needed at all.
Off-channel in general, since it's no longer used for
authentication/association, shouldn't affect PS, so
also remove that logic.
Also document a small caveat for reporting TX status
from off-channel frames in HW remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we've removed all uses of the set_channel
API except for the monitor channel and in libertas,
clarify this. Split the libertas mesh use into a
new libertas_set_mesh_channel() operation, just to
keep backward compatibility, and rename the normal
set_channel() to set_monitor_channel().
Also describe the desired set_monitor_channel()
semantics more clearly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just like the AP mode patch, instead of setting
the channel and then joining the mesh network,
provide the channel to join the network on to
the join_mesh() function.
Like in AP mode, you can also give the channel
to the join-mesh nl80211 command now.
Unlike AP mode, it picks a default channel if
none was given.
As libertas uses mesh mode interfaces but has
no join_mesh callback and we can't simply break
it, keep some compatibility code for that case
and configure the channel directly for it.
In the non-libertas case, where we store the
channel until join, allow setting it while the
interface is down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.
This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.
Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the set_channel function up so it can be used
by other code in this file in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need for ieee80211_set_channel to check
whether a change in configuration happened since
ieee80211_hw_config() auto-detects it.
Additionally, it's wrong to pretend the HT config
for the BSS changed, it didn't, the BSS can't be
up & running (AP beaconing etc.) when the channel
type is changed anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize the debugging to be able to use dynamic_debug.
Coalesce formats, align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 3a25a8c ("mac80211: add improved HW queue control")
added support for offchannel queue mapping. However, this
mapping is only valid when the driver supports
IEEE80211_HW_QUEUE_CONTROL.
Check whether the driver supports IEEE80211_HW_QUEUE_CONTROL
before setting the hw_queue to the mapped offchannel queue.
(This patch doesn't have any actual effect, because
hw_queue is overridden in ieee80211_tx() anyway,
so this is merely some cleanup)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using | with a constant is always true.
Likely this should have be &.
cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new mesh configuration parameter "ht_opmode" and will
allow user to check the current HT protection mode selected. Users could
configure the protection mode by the command "iw mesh_iface set mesh_param
mesh_ht_protection_mode=2". The default protection mode of mesh is set to
non-HT mixed mode.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The signal and noise are forced to be positive since ethtool
deals in unsigned 64-bit values and this number should be human
readable. This gives easy access to some of the data formerly
exposed in the deprecated /proc/net/wireless file.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds hooks to call into the driver to get additional
stats for the ethtool API.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets ethtool print out stats related to stations
connected to the interface. Does not yet get stats
from the underlying driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving a STA to an AP VLAN prevents num_mcast_sta from being decremented
once the STA leaves, because sta->sdata changes. Fix this by checking
for AP VLANs as well.
Also exclude 4-addr VLAN stations from num_mcast_sta - remote 4-addr
stations ignore 3-address multicast frames anyway. In a typical bridge
configuration they receive the same packets as 4-address unicast.
This patch also fixes clearing the sdata->u.vlan.sta pointer when the
STA is removed from a 4-addr VLAN.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the current channel is known, add frequency and channel type to
NL80211_CMD_GET_INTERFACE.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In WoWLAN, we only get the triggers when we actually get
to suspend. As a consequence, drivers currently don't
know that the device should enable wakeup. However, the
device_set_wakeup_enable() API is intended to be called
when the wakeup is enabled, not later when needed.
Add a new set_wakeup() call to cfg80211 and mac80211 to
allow drivers to properly call device_set_wakeup_enable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently only supports one hardware queue
per AC. This is already problematic for off-channel
uses since if we go off channel while the BE queue
is full and then try to send an off-channel frame
the frame will never go out. This will become worse
when we support multi-channel since then a queue on
one channel might be full, but we have to stop the
software queue for all channels. That is obviously
not desirable.
To address this problem allow drivers to register
more hardware queues, and allow them to map them to
virtual interfaces. When they stop a hardware queue
the corresponding AC software queues on the correct
interfaces will be stopped as well. Additionally,
there's an off-channel queue to solve that problem
and a per-interface after-DTIM beacon queue. This
allows drivers to manage software queues closer to
how the hardware works.
Currently, there's a limit of 16 hardware queues.
This may or may not be sufficient, we can adjust it
as needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP netdev is really only active when beaconing, so
manage the carrier state accordingly. Also do that for
VLAN interfaces enslaved to a given AP interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Basic rates are added with supported rates IE and extended supported
rates IE.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report Toffset to userspace.
Let userspace select the mesh synchronization method.
Signed-off-by: Marco Porsch <marco.porsch@s2005.tu-chemnitz.de>
Signed-off-by: Pavel Zubarev <pavel.zubarev@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that don't support QoS also don't support
setting up their ACs, catch that early. While at
it, remove the input check since cfg80211 does it
now.
Also fix up the restart code to not try to set up
the queues in this case.
Finally also change the tx_conf array to have
IEEE80211_NUM_ACS entries instead of # of queues
since that's what it really needs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the plan to change mac80211's queue API to
not map ACs to queues 1:1, it seems necessary to
clarify some APIs that act on ACs rather than on
queues to spell that out explicitly. Do this.
Also verify that the AC number given is valid.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Airtime link metric estimation was broken in HT mesh, use
cfg80211_calculate_bitrate to get the right rate value.
Also factor out tx rate copying from sta_set_sinfo().
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh peer links are established only if average rssi of the peer
candidate satisfies the threshold. This is not in 802.11s specification
but was requested by David Fulgham, an open80211s user. This is a way to avoid
marginal peer links with stations that are barely within range.
This patch adds a new mesh configuration parameter, mesh_rssi_threshold. This
feature is supported only for hardwares that report signal in dBm.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "cfg80211: no cookies in cfg80211_send_XXX()"
Holger Schurig removed the cookies in the calls
from mac80211 to cfg80211, but the ones in the
other direction were left in. Remove them now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP/GO mode API isn't very clearly defined, it
has "set beacon" and "new beacon" etc.
Modify the API to the following:
* start AP -- all settings
* change beacon -- new beacon data
* stop AP -- stop AP mode operation
This also reflects in the nl80211 API, rename
the commands there correspondingly (but keep
the old names for compatibility.)
Overall, this makes it much clearer what's going
on in the API.
Kalle developed the ath6kl changes, I created
the rest of the patch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the second part of the auth/assoc redesign,
the mac80211 part. This moves the auth/assoc code
out of the work abstraction and into the MLME, so
that we don't flip channels all the time etc.
The only downside is that when we are associated,
we need to drop the association in order to create
a connection to another AP, but for most drivers
this is actually desirable and the ability to do
was never used by any applications. If we want to
implement resource reservation with FT-OTA, we'd
probably best do it with explicit R-O-C in wpa_s.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Handle MCS masks set by the user.
* Match rates provided by the rate control algorithm to the mask set,
also in HT mode, and switch back to legacy mode if necessary.
* add debugfs files to observate the rate selection
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the future, when we start notifying drivers,
state transitions could potentially fail. To make
it easier to distinguish between programming bugs
and driver failures:
* rename sta_info_move_state() to
sta_info_pre_move_state() which can only be
called before the station is inserted (and
check this with a new station flag).
* rename sta_info_move_state_checked() to just
plain sta_info_move_state(), as it will be
the regular function that can fail for more
than just one reason (bad transition or an
error from the driver)
This makes the programming model easier -- one of
the functions can only be called before insertion
and can't fail, the other can fail.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the previous beacon filtering patch,
make CQM RSSI support depend on the flags that
the driver set for virtual interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bail out if sta_apply_parameters() returns an error.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When userspace attempts to authorize a station
that is already authorized, nothing happens as
you'd expect. Similarly, when it unauthorizes
a station that is associated, nothing happens.
However, when it unauthorizes a station that
isn't even associated yet, we erroneously try
to move the station to associated. This seems
to happen occasionally as a result of a race
when wpa_supplicant attempts to unauthorize
the port in managed mode. Particularly with my
new patches to keep stations, it can then move
a station into ASSOCIATED state before we have
really associated, which is really confusing.
I introduced this bug in
"mac80211: refactor station state transitions"
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit a9b3cd7f32 (rcu: convert uses of rcu_assign_pointer(x, NULL) to
RCU_INIT_POINTER) did a lot of incorrect changes, since it did a
complete conversion of rcu_assign_pointer(x, y) to RCU_INIT_POINTER(x,
y).
We miss needed barriers, even on x86, when y is not NULL.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If station info contains a beacon loss count, return
it to userspace.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Station entries can have various states, the most
important ones being auth, assoc and authorized.
This patch prepares us for telling the driver about
these states, we don't want to confuse drivers with
strange transitions, so with this we enforce that
they move in the right order between them (back and
forth); some transitions might happen before the
driver even knows about the station, but at least
runtime transitions will be ordered correctly.
As a consequence, IBSS and MESH stations will now
have the ASSOC flag set (so they can transition to
AUTHORIZED), and we can get rid of a special case
in TX processing.
When freeing a station, unwind the state so that
other parts of the code (or drivers later) can rely
on the transitions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to use RCU here, we can just lock
the station mutex instead. This allows the code
to sleep, which is necessary for later patches.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is already checked in cfg80211, so no need
to repeat the checks here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 station handling code is a bit messy
and doesn't do a lot of validation. It seems like
this could be an issue for drivers that don't use
mac80211 to validate everything.
As cfg80211 doesn't keep station state, move the
validation of allowing supported_rates to change
for TDLS only in station mode to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As per 802.11mb 13.9.11.3
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the processing changes in mac80211.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements ht-cap over-rides for mac80211 drivers.
HT may be disabled, making an /a/b/g/n station act like an
a/b/g station. HT40 may be disabled forcing the station to
be HT20 even if the AP and local hardware support HT40.
MAX-AMSDU may be disabled.
AMPDU-Density may be increased.
AMPDU-Factor may be decreased.
This has been successfully tested with ath9k using patched
wpa_supplicant and iw.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The warning is spurious -- if !sta we always exit without using the
unassigned qos variable, and if we do find the sta we assign it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting a probe response template for an interface operating in
AP mode. Low level drivers are notified about changes in the probe
response template and are able to retrieve a copy of the current probe
response. This data can, for example, be uploaded to hardware as a
template.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just add API to get the channel & report it. Trivial really.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize rate control algorithms only when supported rates are known
for a TDLS peer sta. Direct Tx between peers is not allowed before the
link is enabled. In turn, this only occurs after a change_station()
call that sets supported rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For probe responses it can be useful to not wait for ACK to
avoid retransmissions if the station that sent the probe is
already on the next channel, so allow userspace to request
not caring about the ACK with a new nl80211 flag.
Since mac80211 needs to be updated for the new function
prototype anyway implement it right away -- it's just a
few lines of code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support probing clients with null data frames
in AP mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will allow us to support dynamic WEP with 802.1X
properly in mac80211 by not encrypting outgoing and
accepting unencrypted incoming frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's an extra pair of parentheses here that
is simply confusing because it implies a nesting
that doesn't actually exist. Just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to verify whether the command is successful before allocating
the station entry to avoid extra processing. This also fixes a memory
leak on the error path.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only station flags that are already defined in nl80211 are added for
now.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I introduced in-kernel off-channel TX I
introduced a bug -- the work can't be canceled
again because the code clear the skb pointer.
Fix this by keeping track separately of whether
TX status has already been reported.
Cc: stable@kernel.org [2.6.38+]
Reported-by: Jouni Malinen <j@w1.fi>
Tested-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark the STA entries of enabled TDLS peers with a new "peer authorized"
flag.
During link setup, allow special TDLS setup frames through the AP, but
otherwise drop all packets destined to the peer. This is required by the
TDLS (802.11z) specification in order to prevent reordering of MSDUs
between the AP and direct paths.
When setup completes and the peer is authorized, send data directly,
bypassing the AP.
In the Rx path, allow data to be received directly from TDLS peers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding a TDLS peer STA, mark it with a new flag in both nl80211 and
mac80211. Before adding a peer, make sure the wiphy supports TDLS and
our operating mode is appropriate (managed).
In addition, make sure all peers are removed on disassociation.
A TDLS peer is first added just before link setup is initiated. In later
setup stages we have more info about peer supported rates, capabilities,
etc. This info is reported via nl80211_set_station().
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register and implement the TDLS cfg80211 callback functions.
Internally prepare and send TDLS management frames. We incorporate
local STA capabilities and supported rates with extra IEs given by
usermode. The resulting packet is either encapsulated in a data frame,
or assembled as an action frame. It is transmitted either directly or
through the AP, as mandated by the TDLS specification.
Declare support for the TDLS external setup wiphy capability. This
tells usermode to handle link setup and discovery on its own, and use the
kernel driver for sending TDLS mgmt packets.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when hostapd sets the station as authorized
we also overwrite its uAPSD parameter. This obviously
leads to buggy behaviour (later, with my patches that
actually add uAPSD support). To fix this, only apply
those parameters if they were actually set in nl80211,
and to achieve that add a bitmap of things to apply.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
save and configure tx param per sdata, rather than
per hardware.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx params are currently configured per hw, although they
should be configured per interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the scan request or tx_mgmt is requesting not to
use CCK rate for managemet frames through
NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should
select appropriate least non-CCK rate. This could help to
send P2P probes and P2P action frames at non 11b rates
without diabling 11b rates globally.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new nl80211 attribute to specify whether to send the management
frames in CCK rate or not. As of now the wpa_supplicant is disabling
CCK rate at P2P init itself. So this patch helps to send P2P probe
request/probe response/action frames being sent at non CCK rate in 2GHz
without disabling 11b rates.
This attribute is used with NL80211_CMD_TRIGGER_SCAN and
NL80211_CMD_FRAME commands to disable CCK rate for management frame
transmission.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set SSID information from nl80211 beacon parameters. Advertise changes
in SSID to low level drivers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface is removed, the mesh paths associated with it should
also be removed.
This fixes a bug we observed when reloading a device driver module
without reloading mac80211s.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add uapsd_queues and max_sp fields to ieee80211_sta.
These fields might be needed by low-level drivers in
order to configure the AP.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since a v1 of the mesh gate series was accidentally applied, this patch
contains the changes in v2.
These are:
- automatically make mesh gate a root node.
- use TU_TO_EXP_TIME macro.
- initialize timer instead of checking for NULL timer function.
- cleanups.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to set NL80211_MESHCONF_GATE_ANNOUNCEMENTS attribute,
which will advertise this mesh node as being a mesh gate.
NL80211_HWMP_ROOTMODE must be set or this will do nothing.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to set Root Announcement Interval for our mesh
interface. Also, RANN interval is now in proper units of TUs.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For iwlwifi, I decided not to use this API since
it just increased the complexity for little gain.
Since nobody else intends to use it, let's kill
it again. If anybody later needs to have it, we
can always revive it then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When assigning a NULL value to an RCU protected pointer, no barrier
is needed. The rcu_assign_pointer, used to handle that but will soon
change to not handle the special case.
Convert all rcu_assign_pointer of NULL value.
//smpl
@@ expression P; @@
- rcu_assign_pointer(P, NULL)
+ RCU_INIT_POINTER(P, NULL)
// </smpl>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tx_conf array to save the current tx queues
configuration, and reconfig it on resume (ieee80211_reconfig).
On resume, the driver is being reconfigured. Without
reconfiguring the tx queues as well, the driver might
configure the device to use wrong ac params (e.g. ps-poll
instead of uapsd).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just like TKIP and CCMP, CMAC has the PN race.
It might not actually be possible to hit it now
since there aren't multiple ACs for management
frames, but fix it anyway.
Also move scratch buffers onto the stack.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we can process multiple packets at the
same time for different ACs, but the PN is
allocated from a single counter, we need to
use an atomic value there. Use atomic64_t to
make this cheaper on 64-bit platforms, other
platforms will support this through software
emulation, see lib/atomic64.c.
We also need to use an on-stack scratch buf
so that multiple packets won't corrupt each
others scratch buffers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the necessary mac80211 APIs to support
GTK rekey offload, mirroring the functionality
from cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a memeber to the ieee80211_sta structure to indicate whether the STA
supports WME.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds dump support to testmode. The testmode
dump support in nl80211 requires using two of the
six cb->args, the rest can be used by the driver
to figure out where the dump position is at or to
store other data across invocations.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These definitions need to be exposed now that we can set the peer link
states via NL80211_ATTR_STA_PLINK_STATE. They were already being
(opaquely) reported by NL80211_STA_INFO_PLINK_STATE.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds sparse RCU annotations to most of
mac80211, only the mesh code remains to be
done.
Due the the previous patches, the annotations
are pretty simple. The only thing that this
actually changes is removing the RCU usage of
key->sta in debugfs since this pointer isn't
actually an RCU-managed pointer (it only has
a single assignment done before the key even
goes live). As that is otherwise harmless, I
decided to make it part of this patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sched_scan_stopped was called by the driver, mac80211 calls
cfg80211, which in turn was calling mac80211 back with a flag
"driver_initiated". This flag was used so that mac80211 would do the
necessary cleanup but would not call the driver. This was enough to
prevent the bounce back between the driver and mac80211, but not
between mac80211 and cfg80211.
To fix this, we now do the cleanup in mac80211 before calling
cfg80211. To help with locking issues, the workqueue was moved from
cfg80211 to mac80211.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few configuration functions correctly do
rcu_read_lock() but don't correctly reference
some pointers protected by RCU. Fix that.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in ieee80211_del_key() doesn't acquire the
key_mtx properly when it dereferences the keys. It
turns out that isn't actually necessary since the
key_mtx itself seems to be redundant since all key
manipulations are done under the RTNL, but as long
as we have the key_mtx we should use it the right
way too.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/mac80211/cfg.c: In function ‘sta_apply_parameters’:
net/mac80211/cfg.c:746: error: ‘struct sta_info’ has no member named ‘plink_state’
make[1]: *** [net/mac80211/cfg.o] Error 1
make: *** [net/mac80211/mac80211.ko] Error 2
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement support for HW scheduled scan. The mac80211 code doesn't perform
scheduled scans itself, but calls the driver to start and stop scheduled
scans.
This patch also creates a trace event class to be used by drv_hw_scan
and the new drv_sched_scan_start and drv_sched_stop functions, in
order to avoid duplicate code.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new configuration option to support AMPE from userspace.
Prior to this series we only supported authentication in userspace: an
authentication daemon would authenticate peer candidates in userspace
and hand them over to the kernel. From that point the mesh stack would
take over and establish a peer link (Mesh Peering Management).
These patches introduce support for Authenticated Mesh Peering Exchange
in userspace. The userspace daemon implements the AMPE protocol and on
successfull completion create mesh peers and install encryption keys.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds basic support for the new WoWLAN
configuration in mac80211. The behaviour is
completely offloaded to the driver though,
with two new callbacks (suspend/resume).
Options for the driver include a complete
reconfiguration after wakeup, and exposing
all the triggers it wants to support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is based on (but now quite far from) the
original work from Luis and Eliad. Add support
for configuring WoWLAN triggers, and getting
the configuration out again. Changes from the
original patchset are too numerous to list,
but one important change needs highlighting:
the suspend() callback is passed NULL for the
trigger configuration if userspace has not
configured WoWLAN at all.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a new API for setting a TX rate mask in
drivers that have rate control in either the firmware or hardware.
This can be used for various purposes, for example, masking out the
11b rates in P2P operation.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The locking with SMPS requests means that the
debugs file should lock the mgd mutex, not the
iflist mutex. Calls to __ieee80211_request_smps()
need to hold that mutex, so add an assertion.
This has always been wrong, but for some reason
never been noticed, probably because the locking
error only happens while unassociated.
Cc: stable@kernel.org [2.6.34+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add station connected time in debugfs. This will be helpful to get a
measure of stability of the connection and for debugging stress issues
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To NL80211_MESH_SETUP_IE. This reflects our ability to insert any ie
into a mesh beacon, not simply path selection ies.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows user-space monitoring of BSS parameters for the associated
station. This is useful for debugging and verifying that the paramaters
are as expected.
[Exactly the same as before but bundled into a single message]
Signed-off-by: Paul Stewart <pstew@chromium.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If dynamic_ps is disabled, enabling power save before the 4-way
handshake completes may delay the station from being authorized to
send/receive traffic, i.e. increase roaming times. It also may result in
a failed 4-way handshake depending on the AP's timing requirements and
beacon interval, and the station's listen interval.
To fix this, prevent power save from being enabled while the station
isn't authorized and recalculate power save whenever the station's
authorized state changes.
Signed-off-by: Jason Young <a.young.jason@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For devices supported by iwlwifi sometimes
off-channel transmissions need to be handled
by the device completely. To support this
mac80211 needs to pass the frame directly
to the driver and not through the TX path
as the driver needs the frame and channel
information at the same time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some were indirectly set to NO_HT (zero), but I think
it's better to explicitly set it in case the enum ever
changes. In cfg.c, it seems the channel-type was just
ignored (and thus always set to NO_HT).
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no point in disallowing scanning for a
GO interface when it's not beaconing yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we cannot set the channel type, set the channel back to the
original.
Don't update the driver hardware if nothing actually changed.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the off-channel TX is done with remain-on-channel
offloaded to hardware, the reported cookie is wrong as
in that case we shouldn't use the SKB as the cookie but
need to instead use the corresponding r-o-c cookie
(XOR'ed with 2 to prevent API mismatches).
Fix this by keeping track of the hw_roc_skb pointer
just for the status processing and use the correct
cookie to report in this case. We can't use the
hw_roc_skb pointer itself because it is NULL'ed when
the frame is transmitted to prevent it being used
twice.
This fixes a bug where the P2P state machine in the
supplicant gets stuck because it never gets a correct
result for its transmitted frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver has remain-on-channel offload,
implement off-channel transmission using that
primitive.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers to support remain-on-channel
offload if they implement smarter timing or need
to use a device implementation like iwlwifi.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let path selection frames for protocols other than HWMP be sent to
userspace via NL80211_CMD_REGISTER_FRAME. Also allow userspace to send
and receive mesh path selection frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Userspace will now be allowed to toggle between the default path
selection algorithm (HWMP, implemented in the kernel), and a vendor
specific alternative. Also in the same patch, allow userspace to add
information elements to mesh beacons. This is accordance with the
Extensible Path Selection Framework specified in version 7.0 of the
802.11s draft.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh parameters can be to setup a mesh or to configure it.
This patch renames the ambiguous name mesh_params to mesh_config
in preparation for mesh_setup.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for split default keys (unicast
and multicast) in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to specify that a given key
is default only for unicast and/or multicast
transmissions. Only WEP keys are for both,
WPA/RSN keys set here are GTKs for multicast
only. For more future flexibility, allow to
specify all combiations.
Wireless extensions can only set both so use
nl80211; WEP keys (connect keys) must be set
as default for both (but 802.1X WEP is still
possible).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
--
v2: fix ABI breakage and change factor to be a power of 2.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.
Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.
We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.
In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 used to do all its bookkeeping in
the notifier, but some new stuff will have
to use local variables so make the callback
return the netdev pointer.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
