The default EAPD control uses verb command to control EAPD. Some codec
does not have verb command for EAPD. It needs to control by hidden
register.
This update will avoid wrong behavior for some codec. This patch will
fix double setup for EAPD. It just needs to turn on by one site for
verb command or hidden register controlled.
Detailed changes:
- alc889_coef_init() is replaced with alc_update_coef_idx() with a
correct COEF value.
- for ALC262, ALC887 and ALC900, the EAPD setup via the hidden
register is removed because this rather conflicts with the EAPD verb
setup.
- For ALC888-VC, also the hidden register access is removed in
alc888_coef_init().
- Remove the dead #if 0 code for ALC267/ALC268.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These three HP machines all have the same pin config, so we can
change it to a pin quirk.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These HP machines needs GPIO 4 low to enable the headphone amplifier.
In addition, we still need to control LEDs via vref and GPIO.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1387128
Tested-by: TienFu Chen <tienfu.chen@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
es1968_measure_clock uses struct timeval, which on 32-bit systems will overflow
in 2038, leading to incorrect interpretation of time.This patch changes the
function to use ktime_t instead of struct timeval, which implies:
- no y2038: ktime_t uses a 64-bit datatype explicitly.
- efficent subtraction: The earlier version computes the difference in usecs
while dealing with secs and nsecs. It requires checks to see if the nsecs of
stop is less than start. This patch uses a direct subtract of ktime_t and
converts to usecs.
- use of monotonic clock (ktime_get) over real time (do_gettimeofday),
which simplifies timekeeping, as it does not have to deal with cases
where stop_time is less than start_time.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CMI8888 shows the stuttering playback when the snooping is disabled
on the audio buffer. Meanwhile, we've got reports that CORB/RIRB
doesn't work in the snooped mode. So, as a compromise, disable the
snoop only for CORB/RIRB and enable the snoop for the stream buffers.
The resultant patch became a bit ugly, unfortunately, but we still can
live with it.
Reported-and-tested-by: Geoffrey McRae <geoff@spacevs.com>
Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
removed the unused variables. These variables were only being
assigned some value, but the values were never being used.
it has been build tested after removing the variables.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Put more kerneldoc comments to the exported functions.
Still the generic parser code and the HD-audio controller code aren't
covered yet, though.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is concerned with migrating the time variables in the pcxhr
module found in the sound driver. The changes are concerend with the
y2038 problem where timeval will overflow in the year 2038. ktime_t
was used instead of timeval to get the wall time. The difference
is displayed now in nanoseconds instead of microseconds.
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
request_module() handles the printf style arguments, so we don't have
to render strings in the caller side. Not only it reduces the
unnecessary temporary string buffer, it's even safer from the security
POV.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It is lite version of AIO machine(0x0626).
The audio layout of this machine was similar with SSID 0x0626.
The audio was same as commit ad8ff99e6b.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Precedence of & and >> is not the same and is not left to right.
shift has higher precedence and should be done after the mask.
Add parentheses around the mask.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update two records for ALC283 for restore default value.
[The update doesn't seem to have high impact on the existing machines,
but it fixes possible issues, especially expected in BIOS changes on
new machines, according to Realtek -- tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update default value for ALC282 for COEF.
[The update doesn't seem to have high impact on the existing machines,
but it fixes possible issues, especially expected in BIOS changes on
new machines, according to Realtek -- tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without this terminating entry, the pin matching would continue
across random memory until a zero or a non-matching entry was found.
The result being that in some cases, the pin quirk would not be
applied correctly.
Cc: stable@vger.kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
this is a series of patches to just convert the plain info callback
for enum ctl elements to snd_ctl_elem_info(). Also, it includes the
extension of snd_ctl_elem_info(), for catching the unexpected string
cut-off and handling the zero items.
As of now the pointer to struct dai is not being used anywhere in the
function. So it is safe to remove the variable.
If we are ever doing anything with the container_of(daio, struct dai, daio),
then at that time we can again add the variable.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In case there are speakers or headphones as well, anything that only
covers the line out should not be labelled "PCM". Let's name it
"Line Out" instead for clarity.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the scenario where there is one "Line Out", one "Speaker" and one
"Headphone", and there are only two DACs, two outputs will share a DAC.
Currently any mixer on such a DAC will get the "PCM" name, which is
misleading. Instead use "Headphone+LO" or "Speaker+LO" to better
specify what the volume actually controls.
[fixed missing slave string additions by tiwai]
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We implemented in a wrong way for mute LED on Lenovo Ideapad; the bit
must be flipped.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16373
Fixes: 3e887f379d ('ALSA: hda - Add mute LED support to Lenovo Ideapad')
Cc: <stable@vger.kernel.org> # 3.15+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ELD ALSA control change event is sent by hdmi_present_sense() when
eld_changed is true.
Currently, it is only true when the ELD buffer contents have been
modified. However, the user-visible ELD controls also change to a
zero-length value and back when eld_valid is unset/set, and no event is
currently sent in such cases (such as when unplugging or replugging a
sink).
Fix the code to always set eld_changed if eld_valid value is changed,
and therefore to always send the change event when the user-visible
value changes.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch sets the headphones mode to default before suspending
which helps avoid the pop noise on headphones
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
pr_* macros replaced with dev_* as they are more preffered over pr_*.
each file which had pr_* was reviewed manually and replaced with dev_*.
here we have actually used the reference of the vortex which was added
to some functions in the previous patch of this series.
The prefix of the CARD_NAME and prefix of "vortex:" was also
removed as the dev_* will print the device name.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
added a pointer of the vortex in the following functions :
vortex_alsafmt_aspfmt
vortex_Vort3D_InitializeSource
a3dsrc_ZeroStateA3D
so that we can have a reference of the vortex in the function.
this reference of the vortex will actually be used in a later patch
to convert the pr_* macro to dev_*.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the HD Audio Device IDs for the Intel Sunrise Point PCH.
[the item position rearranged by tiwai]
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The emu10k1 voice allocator takes voice_lock spinlock. When there is
no empty stream available, it tries to release a voice used by synth,
and calls get_synth_voice. The callback function,
snd_emu10k1_synth_get_voice(), however, also takes the voice_lock,
thus it deadlocks.
The fix is simply removing the voice_lock holds in
snd_emu10k1_synth_get_voice(), as this is always called in the
spinlock context.
Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is another Thinkpad T440 with SSID 17aa:2212 that has a dock
port.
Reported-by: Siwei Luo <sluo@smartbeans.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
From what I can see, the generic parser is now good enough to handle
Realtek's inverted dmic handling, so let's remove the special handling
and use the generic parser instead.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- More componentisation work from Lars-Peter, this time mainly
cleaning up the suspend and bias level transition callbacks.
- Real system support for the Intel drivers and a bunch of fixes and
enhancements for the associated CODEC drivers, this is going to need
a lot quirks over time due to the lack of any firmware description of
the boards.
- Jack detect support for simple card from Dylan Reid.
- A bunch of small fixes and enhancements for the Freescale drivers.
- New drivers for Analog Devices SSM4567, Cirrus Logic CS35L32, Everest
Semiconductor ES8328 and Freescale cards using the ASRC in newer i.MX
processors.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUMoHRAAoJECTWi3JdVIfQGXUH/RWQ6/Ey70SPgUdWWQ42PFey
sBq/Hl69F8/JNxW6EDA4GEg6ue880Gek0oGqioxtN6Ku0Vm/WSqDWnKcTAGl4dDO
AefC4FwekZWCYQi3VTNIvMEqfUWkcofTLVwjdh/PUZxniahkiGA81UJ1mQNXBxLF
UusrK0fIAxQgiNsCcPZ94knJiqZVBWgbRv/mCXY9K1/jqITNKd/ZVEMkOPk/p00q
cH9LIx8EknRV3HyJNZQ0xpmhpuMzLy6Agf7Oeq/m5kDqq1stmClvibPYkdqkdkto
jYwKaPh18dNHlUmm1w/G7X20kCidhbiwRjS/iIzx3cfIrWkiz90/BSRFKs8pqSo=
=7PPg
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.18
- More componentisation work from Lars-Peter, this time mainly
cleaning up the suspend and bias level transition callbacks.
- Real system support for the Intel drivers and a bunch of fixes and
enhancements for the associated CODEC drivers, this is going to need
a lot quirks over time due to the lack of any firmware description of
the boards.
- Jack detect support for simple card from Dylan Reid.
- A bunch of small fixes and enhancements for the Freescale drivers.
- New drivers for Analog Devices SSM4567, Cirrus Logic CS35L32, Everest
Semiconductor ES8328 and Freescale cards using the ASRC in newer i.MX
processors.
pr_* macros replaced with dev_* as they are more preffered over pr_*.
each file which had pr_* was reviewed manually and replaced with dev_*.
here we have actually used the various snd_card which was added to some
structures of ctxfi via a previous patch of this series.
in the ctvmem.c file we have passed a reference of ct_atc as an
argument to get_vm_block function so that it can be used from
dev_*.
since dev_* will print the device information , so the prefix of
"ctxfi" from the various pr_* were also removed.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
added reference of the card in the convert_format function
so that we can know which card has called the function.
this reference of the snd_card will actually be used in a later patch
to convert the pr_* macro to dev_*.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
initialized the reference of snd_card which was added to the various
structures through the previous patch of the series.
these references of snd_card will be used in a later patch to convert
the pr_* macros to dev_*
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
added a pointer of snd_card in some of the structures to get a
reference of the card from other functions.
these references of snd_card will be initialised in the next patch
of this series and as of now these snd_card will be used to print the
the device information when we convert the pr_* macros to dev_* in a
later patch of this series.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
the previous patch of the series has converted the void * to
struct hw * . Now this patch removes the typecasting to (struct hw *)
which is not needed any more.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
in the code we have void *hw and while using we are always typecasting
it to (struct hw *). it is better to use void type of pointer when we
store different types of pointer , but in this code we are only having
struct hw.
So changed all the relevant reference of void *hw to struct hw *hw,
without any modification of the existing code logic.
the next patch of the series will remove the typecasting which is
not required now.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
fixed sparse warning of incorrect type (different address spaces) in
cthw20k1.c and cthw20k2.c which was being actually caused as mem_base
was of the type unsigned long.
Again as mem_base was previously unsigned long , so it required many
typecasts in the code to convert interger to pointer.
Now after giving the correct type of mem_base as void __iomem *
we can also remove those typecasts maintaining the same functionality
and logic of the code.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If one input has a boost and another one has not, and they're equal
otherwise, it's more likely you want to use the input with the boost
as your primary input.
See hda-emu.git/codecs/canonical/cx20590-lenovo-20b2z00bus-ccert-201305-13496
for an example.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The next patch will use it, so make it visible across modules.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since every caller of snd_hda_jack_detect_enable_callback needs to
use the macros from err.h, it makes sense to include it directly
from hda_jack.h.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds partial support for the Xonar Xense.
[trivial coding style fixes by tiwai]
Signed-off-by: Harley Griggs <hgriggs@posteo.co.uk>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics
and a slightly buggy strncasecmp. The latter is the POSIX name, so
strnicmp was renamed to strncasecmp, and strnicmp made into a wrapper
for the new strncasecmp to avoid breaking existing users.
To allow the compat wrapper strnicmp to be removed at some point in
the future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For its headphone, mic and DSP responses, we can use the standard
hda_jack infrastructure in CA0132 driver, too. The only point to
handle carefully is the delayed headphone jack handling. It tries to
react after a certain delay. Here we use the existing block_report
flag in hda_jack_tbl (that was implemented for HDMI).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous fix for STAC/IDT codecs, the automute hooks in VIA
driver can be also removed by enabling the power control callback for
all pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we can register multiple callbacks to each jack, most of hooks
used in STAC/IDT codecs can be removed by enabling the powermap update
callback for all relevant pins. Along with this, the call of
stac_init_power_map() can be moved back to stac_parse_auto_config()
and the own build_controls callback can be removed, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, hda_jack infrastructure allows only one callback per jack, and
this makes things slightly complicated when a driver wants to assign
multiple tasks to a jack, e.g. the standard auto-mute with a power
up/down sequence. This can be simplified if the hda_jack accepts
multiple callbacks.
This patch is such an extension: the callback-specific part (the
function and private_data) is split to another struct from
hda_jack_tbl, and multiple such objects can be assigned to a single
hda_jack_tbl entry.
The new struct hda_jack_callback is passed to each callback function
now, thus the patch became bigger than expected. But these changes
are mostly trivial.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the other previous changes, this patch for lx6464es takes the
same strategy for converting to nonatomic PCM ops: replacing spinlock
with mutex, converting the irq tasklet to the threaded irq, and
merging the trigger tasklets back to the trigger callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This time PCXHR, another Digigram boards: like the previous patches,
the conversion is straightforward, replacing spinlocks with mutexes,
merging the irq tasklet into the threaded irq handler and the PCM
trigger tasklet back to the trigger callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous patch for VX boards, miXart device driver can be
also rewritten to use nonatomic PCM ops. Simply spinlocks are
replaced with mutex, the tasklet code is merged into the threaded irq
handler. Also, now mgr->msg_mutex is superfluous, so merged to
msg_lock.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rewrite VXpocket and VX222 drivers to use the new PCM nonatomic ops.
The former irq tasklet is replaced with a threaded irq handler, and
the tasklet for the PCM delayed start is simply merged into the normal
PCM trigger, as well as the replacement of spinlock with mutex.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
STAC/IDT driver calls snd_hda_jack_tbl_get() again after calling
snd_hda_jack_detect_enable_callback(). For simplifying this, let's
make snd_hda_jack_detect_enable_callback() returning the pointer while
handling the error with the standard IS_ERR() & co.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The action value assigned to each hda_jack_tbl entry is mostly
superfluous. The actually used values are either the widget NID or a
value specific to the callback.
The former case can be simply replaced by a reference to widget NID
itself. The only place doing the latter is STAC/IDT codec driver for
the powermap handling. But, the code doesn't need to check the action
field at all -- the function jack_update_power() is called either with
a specific pin or with NULL. So the check of jack->action can be
removed completely there, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a driver is set up without the jack detection explicitly (either
by passing a model option or via a specific fixup), the pin powermap
of IDT/STAC codecs is set up wrongly, resulting in the silence
output. It's because of a logic failure in stac_init_power_map().
It tries to avoid creating a callback for the pins that have other
auto-hp and auto-mic callbacks, but the check is done in a wrong way
at a wrong time. The stac_init_power_map() should be called after
creating other jack detection ctls, and the jack callback should be
created only for jack-detectable widgets.
This patch fixes the check in stac_init_power_map() and its callee
at the right place, after snd_hda_gen_build_controls().
Reported-by: Adam Richter <adam_richter2004@yahoo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
as pr_* macros are more preffered over printk, so printk replaced
with corresponding pr_* macros.
this patch will generate warning from checkpatch as it only did printk
replacement and didnot fixed other style issues.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Detect and handle the H6 daughterboard; it works the same as with the
ST, except that there is no conflict with the CS2000 chip.
Tested-by: Andreas Allacher <andreas.allacher@gmx.at>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add one more option to the "Headphones Impedance" control to synchronize
with recent versions of the Windows driver.
Tested-by: fugazzi® <fugazzi99@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few more driver specific fixes on top of the currently pending fixes
(which are already in your tree but not Linus').
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gYI8
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.17
A few more driver specific fixes on top of the currently pending fixes
(which are already in your tree but not Linus').
The DACs on Sigmatel/IDT codecs do mute at the lowest volume level,
and in the earlier drivers, we passed TLV_DB_SCALE_MUTE bit for each
volume control element like Speaker and Headphone as well as Master.
Along with the translation to the generic parser, however, the TLV bit
was lost for the slave controls (e.g. Speaker) but set only to
Master. In theory this should have sufficed, but apps, particularly
PA, do care the slave volume bits, so we seem to see a regression in
the volume controls.
This patch adds a flag to hda_gen_spec to specify the DAC mute
feature, and adds the TLV bit properly for all relevant volume
controls. Also, the TLV bit for vmaster is set in hda_generic.c, so
that we can get rid of all tricks from the codec driver side.
As the similar hack is applied to Conexant 5051 stuff, we can get rid
of it as well.
BugLink: https://bugs.launchpad.net/bugs/1357928
Signed-off-by: Takashi Iwai <tiwai@suse.de>
...by factoring out common parts to the just added pin macros.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will be used in a later patch to make the pin quirk table shorter.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC1150 codec seems to need the COEF- and PLL-setups just like its
compatible ALC882 codec. Some machines (e.g. SunMicro X10SAT) show
the problem like too low output volumes unless the COEF setup is
applied.
Reported-and-tested-by: Dana Goyette <danagoyette@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer Aspire 3830TG with CX20588 codec has a digital built-in mic that
has the same problem like many others, the inverted signal in stereo.
Apply the same fixup to this machine, too.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here contains not many exciting changes but just a few minor ones:
An off-by-one proc write fix, a couple of trivial incldue guard
fixes, Acer laptop pinconfig fix, and a fix for DSD formats that
are still rarely used.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJT/w1wAAoJEGwxgFQ9KSmkkMAQAKlRFjLRrcM+y4ly8Gjr1ZTe
QjkdPBdkQlWiMIPLlX1Xr+pWG5kZiUMiAl5lBkiF6ubcjVYl6KoJGzGzwcAdYkor
H0tY2+mqinOS9gi3qwnTQjvlhGeTwLqs7hIkIjfaaUHSBn5I6TYsMgMQ2I6Rmo82
Ox6bhJbunNRhCpyebzTjzgcruGej8FkzpJullWs6XTdxCY2rtFpVn0b6FUgdbab+
uTgfBeckvtIA327s7qRmWyAOn5t73tCqV3CJ/PnBCXByODiMRrkaM0OLb/O7QvN5
VTrKyGQyUhf3WNT6R1nuGPbC24ajxu5p0GkSZNuHWoerMIgNobtoBNplzL+P8UUs
s83Sm21Y7n2jSXPs+rJdjy4MdLng6QcXH/ZoCnpZeIeVxs4qU4O9Q7HMDJZCYS7M
EEutl8/gt43su4wHO2RGfU3DOIFnjtPQzqqkkwzdwoxB9jhMHfq73qRTrAHC3biB
hqjRQRcX++Z5C0PPuVUvRSwidWTbeEfot3MvXKXaHyWTojyGRqfKsCXhudFLCNYU
BlwAxrLI8kWaKdr9oVe+KS1XoBVQJIIar62plwFozTEuHuQ2P0FNpP6MFViPNoFf
UOHvXCTHi8JaVSBjhlKHrtto2Zcak1tIlQ1Ewog0Wg1cJrDOdWxHEwJ2tUI0N7aC
fZ3lwxhRarA9URNrjNqV
=raXL
-----END PGP SIGNATURE-----
Merge tag 'sound-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here contains not many exciting changes but just a few minor ones: An
off-by-one proc write fix, a couple of trivial incldue guard fixes,
Acer laptop pinconfig fix, and a fix for DSD formats that are still
rarely used"
* tag 'sound-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Set up initial pins for Acer Aspire V5
ALSA: pcm: Fix the silence data for DSD formats
ALSA: ctxfi: ct20k1reg: Fix typo in include guard
ALSA: hda: ca0132_regs.h: Fix typo in include guard
ALSA: core: fix buffer overflow in snd_info_get_line()
Acer Aspire V5 doesn't set up the pins correctly at the cold boot
while the pins are corrected after the warm reboot. This patch gives
the proper pin configs statically in the driver as a workaround.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81561
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds to the readability of the ice1712 driver.
Signed-off-by: Konstantinos Tsimpoukas <kostaslinuxxx@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
as broken user-visible strings breaks the ability to grep for them , so this patch fixes the broken user-visible strings
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
as pr_* macros are more preffered over printk, so printk replaced with corresponding pr_err and pr_alert
this patch will generate a warning from checkpatch for an unnecessary space before new line and has not been fixed as this patch is only for printk replacement.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A bunch of ASoC fixes with a few HD-audio fixes in this pull request.
All fairly small, boring and device-specific fixes, in addition to
MAINTAINERS update for better reviewing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=x5gm
-----END PGP SIGNATURE-----
Merge tag 'sound-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A bunch of ASoC fixes with a few HD-audio fixes in this pull request.
All fairly small, boring and device-specific fixes, in addition to
MAINTAINERS update for better reviewing"
* tag 'sound-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/hdmi - apply Valleyview fix-ups to Cherryview display codec
ALSA: hda/hdmi - set depop_delay for haswell plus
ALSA: hda - restore the gpio led after resume
ALSA: hda/realtek - Avoid setting wrong COEF on ALC269 & co
ASoC: pxa-ssp: drop SNDRV_PCM_FMTBIT_S24_LE
ASoC: fsl-esai: Revert .xlate_tdm_slot_mask() support
ASoC: mcasp: Fix implicit BLCK divider setting
ASoC: arizona: Fix TDM slot length handling in arizona_hw_params
ASoC: pcm512x: Correct Digital Playback control names
ASoC: dapm: Fix uninitialized variable in snd_soc_dapm_get_enum_double()
ASoC: Intel: Restore Baytrail ADSP streams only when ADSP was in reset
ASoC: Intel: Wait Baytrail ADSP boot at resume_early stage
ASoC: Intel: Merge Baytrail ADSP suspend_noirq into suspend_late
MAINTAINERS: Add i.MX maintainers and paths to Freescale ASoC entry
ASoC: Intel: Update Baytrail ADSP firmware name
Valleyview and Cherryview have the same behavior on display audio. So this patch
defines is_valleyview_plus() to include codecs for both Valleyview and its successor
Cherryview, and apply Valleyview fix-ups to Cherryview.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both Haswell and Broadwell need set depop_delay to 0. So apply this
setting to haswell plus.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are many codes doing writes or updates COEF verbs sequentially
in a batch. Rewrite such open codes with tables for optimization.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The helper functions snd_hda_check_board_config() and
snd_hda_check_board_codec_sid_config() are no longer used since the
transition to the generic parser and all quirks have been replaced
with fixups. Let's kill these dead codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some HP laptops, the mute led is controlled by codec gpio.
When some machine resume from s3/s4, the codec gpio data will be
cleared to 0 by BIOS:
Before suspend:
IO[3]: enable=1, dir=1, wake=0, sticky=0, data=1, unsol=0
After resume:
IO[3]: enable=1, dir=1, wake=0, sticky=0, data=0, unsol=0
To skip the AFG node to enter D3 can't fix this problem.
A workaround is to restore the gpio data when the system resume
back from s3/s4. It is safe even on the machines without this
problem.
BugLink: https://bugs.launchpad.net/bugs/1358116
Tested-by: Franz Hsieh <franz.hsieh@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC269 & co have many vendor-specific setups with COEF verbs.
However, some verbs seem specific to some codec versions and they
result in the codec stalling. Typically, such a case can be avoided
by checking the return value from reading a COEF. If the return value
is -1, it implies that the COEF is invalid, thus it shouldn't be
written.
This patch adds the invalid COEF checks in appropriate places
accessing ALC269 and its variants. The patch actually fixes the
resume problem on Acer AO725 laptop.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52181
Tested-by: Francesco Muzio <muziofg@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here is the additional fix patches that have been queued up since the
previous pull request. A few HD-audio fixes, a USB-audio quirk
addition, and a couple of trivial cleanup for the legacy OSS codes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=UPFy
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here is the additional fix patches that have been queued up since the
previous pull request. A few HD-audio fixes, a USB-audio quirk
addition, and a couple of trivial cleanup for the legacy OSS codes"
* tag 'sound-fix-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Set TLV_DB_SCALE_MUTE bit for cx5051 vmaster
ALSA: hda/ca0132 - Don't try loading firmware at resume when already failed
ALSA: hda - Fix pop noises on reboot for Dell XPS 13 9333
ALSA: hda - Set internal mic as default input source on Dell XPS 13 9333
ALSA: usb-audio: fix BOSS ME-25 MIDI regression
ALSA: hda - Fix parsing of CMI8888 codec
ALSA: hda - Fix probing and stuttering on CMI8888 HD-audio controller
ALSA: hda/realtek - Fixed ALC286/ALC288 recording delay for Headset Mic
sound: oss: Remove typedefs wanc_info and wavnc_port_info
sound: oss: uart401: Remove typedef uart401_devc
Conexnat HD-audio driver has a workaround for cx5051 (aka CX20561)
chip to add fake mute controls to each amp (commit 3868137e). This
implies the minimum-as-mute TLV bit in TLV for each corresponding
control. Meanwhile we build the virtual master from these, but the
TLV bit is missing, even though the slaves have it.
This patch simply adds the missing TLV_DB_SCALE_MUTE bit for vmaster,
as already done in patch_sigmatel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CA0132 driver tries to reload the firmware at resume. Usually this
works since the firmware loader core caches the firmware contents by
itself. However, if the driver failed to load the firmwares
(e.g. missing files), reloading the firmware at resume goes through
the actual file loading code path, and triggers a kernel WARNING like:
WARNING: CPU: 10 PID:11371 at drivers/base/firmware_class.c:1105 _request_firmware+0x9ab/0x9d0()
For avoiding this situation, this patch makes CA0132 skipping the f/w
loading at resume when it failed at probe time.
Reported-and-tested-by: Janek Kozicki <cosurgi@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If nid 0x15 (Headphone Playback Switch) is in D3 and headphones are
plugged in when the laptop reboots, a pop noise is generated.
Prevent this by keeping nid 0x15 in D0 when headphones are plugged in.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=76611
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the laptop is powered on with a jack plugged in, independently on what
is plugged, the jack is treated as a microphone jack.
Initialize the capture source so that by default jacks are treated as
headphones jacks. This will also prevent pop noises on boot in case
headphones are plugged in since setting/unsetting mic-in as input source
causes a pop noise.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=76611
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CMI8888 codec chip has a boost amp (only) on the headphone pin, and
this confuses the generic parser, which tends to pick up the most
outside amp. This results in the wrong volume setup, as the driver
complains like:
hda_codec: Mismatching dB step for vmaster slave (-100!=1000)
For avoiding this problem, rule out the amp on NID 0x10 and create
"Headphone Amp" volume control manually instead.
Note that this patch still doesn't fix all problems yet. The sound
output from the line out seems still too low. It will be fixed in
another patch (hopefully).
Reported-and-tested-by: Vincent Lejeune <vljn@ovi.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS Phoebus with CMI8888 HD-audio chip (PCI id 13f6:5011) doesn't
work with HD-audio driver as is because of some weird nature. For
making DMA properly working, we need to disable MSI. The position
report buffer doesn't work, thus we need to force reading LPIB
instead. And yet, the codec CORB/RIRB communication gives errors
unless we disable the snooping (caching).
In this patch, all these workarounds are added as a quirk for the
device. The HD-audio *codec* chip needs yet another workaround, but
it'll be provided in the succeeding patch.
Reported-and-tested-by: Vincent Lejeune <vljn@ovi.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It will be recording voice delay for resume back recording for Headset Mic.
This alc286 will quickly open Headset Mic, to prevent avoid recording files are missing.
The issue was fixed. This is follow ALC286 programing guide.
[fix build error, add static and renamed the function by tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just add the PCI ID for the STX II. It appears to work the same as the
STX, except for the addition of the not-yet-supported daughterboard.
Tested-by: Mario <fugazzi99@gmail.com>
Tested-by: corubba <corubba@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862883) and module alias for Braswell
display codec.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add HD Audio Device PCI ID for the Intel Braswell platform.
It is an HDA Intel PCH controller.
AZX_DCAPS_ALIGN_BUFSIZE is not necessary for this controller.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mic mute led on dell laptops is controlled by the wmi driver.
Followed this part being merged to the kernel, we add the mic mute led
hook in the hda driver.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ON the machine, two pin complex (0xb and 0xe) are both routed to
the same external right-side mic jack, this makes the jack can't work.
To fix this problem, set the 0xe to "not connected".
BugLink: https://bugs.launchpad.net/bugs/1350148
Tested-by: Franz Hsieh <franz.hsieh@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell XPS 15 (1028:05fe) gives the bad feedback noise from analog
loopback line even if the channels are muted. The similar problem has
been seen on XPS 13, and it was fixed by simply disabling loopback.
The same fixup was confirmed to be applicable and fix the problem on
XPS 15, too.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80821
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new quirk table to make sure that pin quirks have a higher
priority than quirks that apply to an entire vendor.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previously, calling one quirk function first and another later
would make the latter one take priority, this is now changed
to make the former take priority.
By adding two special values for fixup_id we can also get rid of the
fixup_forced flag.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Gigabyte BRIX BXBT-2707 is a mini-PC with Realtek ALC283 HDA,
exposing a single headset jack.
However, the default pin config information only suggests
that one pin is connected: a HP out jack (pin 0x21, default
config 0x04211010).
The microphone input is behind pin 0x19, which has default
config 0x411111f0 (i.e. unused), so it does not show up in
userspace, and no microphone input is possible via the headset.
Override the pin config so that the headset mic can be used.
[rearranged the fixup entry position by tiwai]
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This makes the mute LED work on a HP 15 touchsmart machine.
BugLink: https://bugs.launchpad.net/bugs/1334950
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
