This makes each result entry to be checked using skb_pull_data instead
of acessing them by index.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds support for Set Privacy Mode when updating the resolving list
when HCI_CONN_FLAG_DEVICE_PRIVACY so the controller shall use Device
Mode for devices programmed in the resolving list, Device Mode is
actually required when the remote device are not able to use RPA as
otherwise the default mode is Network Privacy Mode in which only
allows RPAs thus the controller would filter out advertisement using
identity addresses for which there is an IRK.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change the use of switch statement to a function table which is
easier to extend.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change the use of switch statement to a function table which is
easier to extend and can include min/max length of each command.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change the use of switch statement to a function table which is
easier to extend and can include min/max length of each subevent.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change the use of switch statement to a function table
which is easier to extend and can include min/max length of each HCI
event.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the LE Direct Advertising Report
events received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the LE Extended Advertising Report
events received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the LE Advertising Report events
received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the LE Metaevents received have the
minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the Extended Inquiry Result events
received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the Inquiry Result with RSSI events
received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the Inquiry Result events received
have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the Number of Complete Packets events
received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the Command Complete events received
have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the BR/EDR events received have the
minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When doing remote name request, we cannot scan. In the normal case it's
OK since we can expect it to finish within a short amount of time.
However, there is a possibility to scan lots of devices that
(1) requires Remote Name Resolve
(2) is unresponsive to Remote Name Resolve
When this happens, we are stuck to do Remote Name Resolve until all is
done before continue scanning.
This patch adds a time limit to stop us spending too long on remote
name request.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Introducing NAME_REQUEST_FAILED flag that will be sent together with
device found event on name resolve failure. This will provide the
userspace with an information so it can decide not to resolve the
name for these devices in the future.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
num_keys is actually 2 octects not 1:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E
page 1989:
Num_Keys_Deleted:
Size: 2 octets
0xXXXX Number of Link Keys Deleted
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Both max_num_keys and num_key are 2 octects:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E
page 1985:
Max_Num_Keys:
Size: 2 octets
Range: 0x0000 to 0xFFFF
Num_Keys_Read:
Size: 2 octets
Range: 0x0000 to 0xFFFF
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Check for out-of-bound read was being performed at the end of while
num_reports loop, and would fill journal with false positives. Added
check to beginning of loop processing so that it doesn't get checked
after ptr has been advanced.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should clear the flag if the adv instance removed due to receiving
this error status is the last one we have.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This event is received when the controller stops advertising,
specifically for these three reasons:
(a) Connection is successfully created (success).
(b) Timeout is reached (error).
(c) Number of advertising events is reached (error).
(*) This event is NOT generated when the host stops the advertisement.
Refer to the BT spec ver 5.3 vol 4 part E sec 7.7.65.18. Note that the
section was revised from BT spec ver 5.0 vol 2 part E sec 7.7.65.18
which was ambiguous about (*).
Some chips (e.g. RTL8822CE) send this event when the host stops the
advertisement with status = HCI_ERROR_CANCELLED_BY_HOST (due to (*)
above). This is treated as an error and the advertisement will be
removed and userspace will be informed via MGMT event.
On suspend, we are supposed to temporarily disable advertisements,
and continue advertising on resume. However, due to the behavior
above, the advertisements are removed instead.
This patch returns early if HCI_ERROR_CANCELLED_BY_HOST is received.
Btmon snippet of the unexpected behavior:
@ MGMT Command: Remove Advertising (0x003f) plen 1
Instance: 1
< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 6
Extended advertising: Disabled (0x00)
Number of sets: 1 (0x01)
Entry 0
Handle: 0x01
Duration: 0 ms (0x00)
Max ext adv events: 0
> HCI Event: LE Meta Event (0x3e) plen 6
LE Advertising Set Terminated (0x12)
Status: Operation Cancelled by Host (0x44)
Handle: 1
Connection handle: 0
Number of completed extended advertising events: 5
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
Status: Success (0x00)
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Coverity Scan report:
[...]
*** CID 1493985: Uninitialized variables (UNINIT)
/net/bluetooth/hci_event.c: 4535 in hci_sync_conn_complete_evt()
4529
4530 /* Notify only in case of SCO over HCI transport data path which
4531 * is zero and non-zero value shall be non-HCI transport data path
4532 */
4533 if (conn->codec.data_path == 0) {
4534 if (hdev->notify)
>>> CID 1493985: Uninitialized variables (UNINIT)
>>> Using uninitialized value "notify_evt" when calling "*hdev->notify".
4535 hdev->notify(hdev, notify_evt);
4536 }
4537
4538 hci_connect_cfm(conn, ev->status);
4539 if (ev->status)
4540 hci_conn_del(conn);
[...]
Although only btusb uses air_mode, and he only handles HCI_NOTIFY_ENABLE_SCO_CVSD
and HCI_NOTIFY_ENABLE_SCO_TRANSP, there is still a very small chance that
ev->air_mode is not equal to 0x2 and 0x3, but notify_evt is initialized to
HCI_NOTIFY_ENABLE_SCO_CVSD or HCI_NOTIFY_ENABLE_SCO_TRANSP. the context is
maybe not correct.
Let us directly use the required function instead of re-initializing it,
so as to restore the original logic and make the code more correct.
Addresses-Coverity: ("Uninitialized variables")
Fixes: f4f9fa0c07 ("Bluetooth: Allow usb to auto-suspend when SCO use non-HCI transport")
Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Syzbot reported slab-out-of-bounds read in hci_le_adv_report_evt(). The
problem was in missing validaion check.
We should check if data is not malicious and we can read next data block.
If we won't check ptr validness, code can read a way beyond skb->end and
it can cause problems, of course.
Fixes: e95beb4141 ("Bluetooth: hci_le_adv_report_evt code refactoring")
Reported-and-tested-by: syzbot+e3fcb9c4f3c2a931dc40@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes hci_suspend_notifier use the hci_*_sync which can be
executed synchronously which is allowed in the suspend_notifier and
simplifies a lot of the handling since the status of each command can
be checked inline so no other work need to be scheduled thus can be
performed without using of a state machine.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
mgmt-tester paths:
Set SSP on - Success 2
Set Device ID - SSP off and Power on
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This replaces the use of hci_update_background_scan with
hci_update_passive_scan which runs from cmd_work_sync and deal properly
with resolving list when LL privacy is enabled.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we remove one instance of adv using Set Extended Adv Enable, there
is a possibility of issue occurs when processing the Command Complete
event. Especially, the adv_info might not be found since we already
remove it in hci_req_clear_adv_instance() -> hci_remove_adv_instance().
If that's the case, we will mistakenly proceed to remove all adv
instances instead of just one single instance.
This patch fixes the issue by checking the content of the HCI command
instead of checking whether the adv_info is found.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When SUSPEND_DISCONNECTING bit is set that means Disconnect is pending
but the code was evaluating if the list is empty before calling
hci_conn_del which does the actual cleanup and remove the connection
from the list thus the bit is never cleared causing the suspend
procedure to always timeout when there are connections to be
disconnected:
Suspend/Resume - Success 5 (Pairing - Legacy) - waiting done
Set the system into Suspend via force_suspend
= mgmt-tester: Suspend/Resume - Success 5 (Pairing -.. 17:03:13.200458
= mgmt-tester: Set the system into Suspend via force_suspend 17:03:13.205812
< HCI Command: Write Scan E.. (0x03|0x001a) plen 1 #122 [hci0] 17:03:13.213561
Scan enable: No Scans (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #123 [hci0] 17:03:13.214710
Write Scan Enable (0x03|0x001a) ncmd 1
Status: Success (0x00)
< HCI Command: Disconnect (0x01|0x0006) plen 3 #124 [hci0] 17:03:13.215830
Handle: 42
Reason: Remote Device Terminated due to Power Off (0x15)
> HCI Event: Command Status (0x0f) plen 4 #125 [hci0] 17:03:13.216602
Disconnect (0x01|0x0006) ncmd 1
Status: Success (0x00)
> HCI Event: Disconnect Complete (0x05) plen 4 #126 [hci0] 17:03:13.217342
Status: Success (0x00)
Handle: 42
Reason: Remote Device Terminated due to Power Off (0x15)
@ MGMT Event: Device Disconn.. (0x000c) plen 8 {0x0002} [hci0] 17:03:13.217688
BR/EDR Address: 00:AA:01:01:00:00 (Intel Corporation)
Reason: Connection terminated by local host for suspend (0x05)
@ MGMT Event: Device Disconn.. (0x000c) plen 8 {0x0001} [hci0] 17:03:13.217688
BR/EDR Address: 00:AA:01:01:00:00 (Intel Corporation)
Reason: Connection terminated by local host for suspend (0x05)
Suspend/Resume - Success 5 (Pairing - Legacy) - test timed out
= mgmt-tester: Suspend/Resume - Success 5 (Pairing -.. 17:03:13.939317
Suspend/Resume - Success 5 (Pairing - Legacy) - teardown
= mgmt-tester: Suspend/Resume - Success 5 (Pairing -.. 17:03:13.947267
[ 13.284291] Bluetooth: hci0: Timed out waiting for suspend events
[ 13.287324] Bluetooth: hci0: Suspend timeout bit: 6
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This moves functions manipulating EIR/Adv Data to its own file so it
can be reused by other files.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently usb tranport is not allowed to suspend when SCO over
HCI tranport is active.
This patch shall enable the usb tranport to suspend when SCO
link use non-HCI transport.
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When connecting to a device using an RPA if the address has been
resolved by the controller (types 0x02 and 0x03) the identity address
shall be used as the actual RPA in the advertisement won't be visible
to the host.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Address types ADDR_LE_DEV_PUBLIC_RESOLVED and
ADDR_LE_DEV_RANDOM_RESOLVED shall be converted to ADDR_LE_PUBLIC and
ADDR_LE_RANDOM repectively since they are not safe to be used beyond
the scope of the events themselves.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When disconnecting the advertising shall be re-enabled only when the
connection role is slave/peripheral as the central role use advertising
to connect it could end up enabling the instance 0x00 if there are other
advertising instances.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For NOP command, need to cancel work scheduled on cmd_timer,
on receiving command status or commmand complete event.
Below use case might lead to race condition multiple when NOP
commands are queued sequentially:
hci_cmd_work() {
if (atomic_read(&hdev->cmd_cnt) {
.
.
.
atomic_dec(&hdev->cmd_cnt);
hci_send_frame(hdev,...);
schedule_delayed_work(&hdev->cmd_timer,...);
}
}
On receiving event for first NOP, the work scheduled on hdev->cmd_timer
is not cancelled and second NOP is dequeued and sent to controller.
While waiting for an event for second NOP command, work scheduled on
cmd_timer for the first NOP can get scheduled, resulting in sending third
NOP command (sending back to back NOP commands). This might
cause issues at controller side (like memory overrun, controller going
unresponsive) resulting in hci tx timeouts, hardware errors etc.
The fix to this issue is to cancel the delayed work scheduled on
cmd_timer on receiving command status or command complete event for
NOP command (this patch handles NOP command same as any other SIG
command).
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Acked-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This stores the advertising handle/instance into hci_conn so it is
accessible when re-enabling the advertising once disconnected.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
LE Enhanced Connection Complete contains the Local RPA used in the
connection which must be used when set otherwise there could problems
when pairing since the address used by the remote stack could be the
Local RPA:
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 4, Part E
page 2396
'Resolvable Private Address being used by the local device for this
connection. This is only valid when the Own_Address_Type (from the
HCI_LE_Create_Connection, HCI_LE_Set_Advertising_Parameters,
HCI_LE_Set_Extended_Advertising_Parameters, or
HCI_LE_Extended_Create_Connection commands) is set to 0x02 or
0x03, and the Controller generated a resolvable private address for the
local device using a non-zero local IRK. For other Own_Address_Type
values, the Controller shall return all zeros.'
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Code was checking if random_addr and hdev->rpa match without first
checking if the RPA has not been set (BDADDR_ANY), furthermore it was
clearing HCI_RPA_EXPIRED before the command completes and the RPA is
actually programmed which in case of failure would leave the expired
RPA still set.
Since advertising instance have a similar problem the clearing of
HCI_RPA_EXPIRED has been moved to hci_event.c after checking the random
address is in fact the hdev->rap and then proceed to set the expire
timeout.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds a field to track if advertising instances are enabled or not
and only clear HCI_LE_ADV flag if there is no instance left advertising.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Syzbot reported a corrupted list in kobject_add_internal [1]. This
happens when multiple HCI_EV_SYNC_CONN_COMPLETE event packets with
status 0 are sent for the same HCI connection. This causes us to
register the device more than once which corrupts the kset list.
As this is forbidden behavior, we add a check for whether we're
trying to process the same HCI_EV_SYNC_CONN_COMPLETE event multiple
times for one connection. If that's the case, the event is invalid, so
we report an error that the device is misbehaving, and ignore the
packet.
Link: https://syzkaller.appspot.com/bug?extid=66264bf2fd0476be7e6c [1]
Reported-by: syzbot+66264bf2fd0476be7e6c@syzkaller.appspotmail.com
Tested-by: syzbot+66264bf2fd0476be7e6c@syzkaller.appspotmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Error status of this event means that it has ended due reasons other
than a connection:
'If advertising has terminated as a result of the advertising duration
elapsing, the Status parameter shall be set to the error code
Advertising Timeout (0x3C).'
'If advertising has terminated because the
Max_Extended_Advertising_Events was reached, the Status parameter
shall be set to the error code Limit Reached (0x43).'
Fixes: acf0aeae43 ("Bluetooth: Handle ADv set terminated event")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
blacklist -> reject list
whitelist -> accept list
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> central
slave -> peripheral
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> initiator (for smp) or central (everything else)
slave -> responder (for smp) or peripheral (everything else)
The #define preprocessor terms are unchanged for now to not disturb
dependent APIs.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
slave -> peripheral
blacklisted -> blocked
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
