This patch fixes the problem that issuing SHPC command in poll mode
always fails with the following message.
shpchp: Command not completed in 2000 msec
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CONFIG_PCI=n, CONFIG_HT_IRQ=y results in the following compile error:
...
LD vmlinux
arch/i386/mach-generic/built-in.o: In function `apicid_to_node':
summit.c:(.text+0x53): undefined reference to `apicid_2_node'
arch/i386/kernel/built-in.o: In function `arch_setup_ht_irq':
(.text+0xcf79): undefined reference to `write_ht_irq_low'
arch/i386/kernel/built-in.o: In function `arch_setup_ht_irq':
(.text+0xcf85): undefined reference to `write_ht_irq_high'
arch/i386/kernel/built-in.o: In function `k7nops':
alternative.c:(.data+0x1358): undefined reference to `mask_ht_irq'
alternative.c:(.data+0x1360): undefined reference to `unmask_ht_irq'
make[1]: *** [vmlinux] Error 1
Bug report by Jesper Juhl.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
This moves the declarations for the architecture helpers into
include/linux/htirq.h from the generic include/linux/pci.h. Hopefully this
will make this distinction clearer.
htirq.h is included where it is needed.
The dependency on the msi code is fixed and removed.
The Makefile is tidied up.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is just a few makefile tweaks and some file renames.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out msi_ops was simply not enough to abstract the architecture
specific details of msi. So I have moved the resposibility of constructing
the struct irq_chip to the architectures, and have two architecture specific
functions arch_setup_msi_irq, and arch_teardown_msi_irq.
For simple architectures those functions can do all of the work. For
architectures with platform dependencies they can call into the appropriate
platform code.
With this msi.c is finally free of assuming you have an apic, and this
actually takes less code.
The helpers for the architecture specific code are declared in the linux/msi.h
to keep them separate from the msi functions used by drivers in linux/pci.h
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The logic works like this.
Since we no longer track the state logic by hand in msi.c startup and shutdown
are no longer needed.
By updating msi_set_mask_bit to work on msi devices that do not implement a
mask bit we can always call the mask/unmask functions.
What we really have are mask and unmask so we use them to implement the .mask
and .unmask functions instead of .enable and .disable.
By switching to the handle_edge_irq handler we only need an ack function that
moves the irq if necessary. Which removes the old end and ack functions and
their peculiar logic of sometimes disabling an irq.
This removes the reliance on pre genirq irq handling methods.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently msi.c is doing sanity checks that make certain before an irq is
destroyed it has no more users.
By adding irq_has_action I can perform the test is a generic way, instead of
relying on a msi specific data structure.
By performing the core check in dynamic_irq_cleanup I ensure every user of
dynamic irqs has a test present and we don't free resources that are in use.
In msi.c this allows me to kill the attrib.state member of msi_desc and all of
the assciated code to maintain it.
To keep from freeing data structures when irq cleanup code is called to soon
changing dyanamic_irq_cleanup is insufficient because there are msi specific
data structures that are also not safe to free.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements two functions ht_create_irq and ht_destroy_irq for
use by drivers. Several other functions are implemented as helpers for
arch specific irq_chip handlers.
The driver for the card I tested this on isn't yet ready to be merged.
However this code is and hypertransport irqs are in use in a few other
places in the kernel. Not that any of this will get merged before 2.6.19
Because the ipath-ht400 is slightly out of spec this code will need to be
generalized to work there.
I think all of the powerpc uses are for a plain interrupt controller in a
chipset so support for native hypertransport devices is a little less
interesting.
However I think this is a half way decent model on how to separate arch
specific and generic helper code, and I think this is a functional model of
how to get the architecture dependencies out of the msi code.
[akpm@osdl.org: Kconfig fix]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After the previous changes ia64 is the only architecture useing msi-apic.c
[akpm@osdl.org: unbreak MSI on ia64]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The msi currently allocates irqs backwards. First it allocates a platform
dependent routing value for an interrupt the ``vector'' and then it figures
out from the vector which irq you are on.
For ia64 this is fine. For x86 and x86_64 this is complete nonsense and makes
an enourmous mess of the irq handling code and prevents some pretty
significant cleanups in the code for handling large numbers of irqs.
This patch refactors msi.c to work in terms of irqs and create_irq/destroy_irq
for dynamically managing irqs.
Hopefully this is finally a version of msi.c that is useful on more than just
x86 derivatives.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently we attempt to predict how many irqs we will be able to allocate with
msi using pci_vector_resources and some complicated accounting, and then we
only allow each device as many irqs as we think are available on average.
Only the s2io driver even takes advantage of this feature all other drivers
have a fixed number of irqs they need and bail if they can't get them.
pci_vector_resources is inaccurate if anyone ever frees an irq. The whole
implmentation is racy. The current irq limit policy does not appear to make
sense with current drivers. So I have simplified things. We can revisit this
we we need a more sophisticated policy.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current msi_ops are short sighted in a number of ways, this patch attempts
to fix the glaring deficiences.
- Report in msi_ops if a 64bit address is needed in the msi message, so we
can fail 32bit only msi structures.
- Send and receive a full struct msi_msg in both setup and target. This is
a little cleaner and allows for architectures that need to modify the data
to retarget the msi interrupt to a different cpu.
- In target pass in the full cpu mask instead of just the first cpu in case
we can make use of the full cpu mask.
- Operate in terms of irqs and not vectors, currently there is still a 1-1
relationship but on architectures other than ia64 I expect this will change.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In support of this I also add a struct msi_msg that captures the the two
address and one data field ina typical msi message, and I remember the pos and
if the address is 64bit in struct msi_desc.
This makes the code a little more readable and easier to maintain, and paves
the way to further simplfications.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows the output of the msi tests to be stored directly in a bit field.
If you don't do this a value greater than one will be truncated and become 0.
Changing true to false with bizare consequences.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The problem. Because the disable routines leave the msi interrupts in all
sorts of half enabled states the enable routines become impossible to
implement correctly, and almost impossible to understand.
Simplifing this allows me to simply kill the buggy reroute_msix_table, and
generally makes the code more maintainable.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roland Dreier wrote:
> The change "PCI: assign ioapic resource at hotplug" (commit
> 2318627965 in Linus's tree) makes
> networking stop working on my system (SuperMicro H8QC8 with four
> dual-core Opteron 885 CPUs). In particular, the on-board NIC stops
> working, probably because it gets assigned the wrong IRQ (225 in the
> non-working case, 217 in the working case)
>
> With that patch applied, e1000 doesn't work. Reverting just that
> patch (shown below) from Linus's latest tree fixes things for me.
>
The cause of this problem might be an wrong assumption that the 'start'
member of resource structure for ioapic device has non-zero value if the
resources are assigned by firmware. The 'start' member of ioapic device
seems not to be set even though the resources were actually assigned to
ioapic devices by firmware.
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Cc: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes two things
Firstly someone mistakenly used "errata" for the singular. This causes
Dave Woodhouse to emit diagnostics whenever the string is read, and so
should be fixed.
Secondly the AMD AGP tunnel has an erratum which causes hangs if you try
and do direct PCI to AGP transfers in some cases. We have a flag for
PCI/PCI failures but we need a different flag for this really as in this
case we don't want to stop PCI/PCI transfers using things like IOAT and the
new RAID offload work.
I'll post some updates to make proper use of the PCIAGP flag in the
media/video drivers to Mauro.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patches reduce the size of the VFS inode structure by 28 bytes
on a UP x86. (It would be more on an x86_64 system). This is a 10% reduction
in the inode size on a UP kernel that is configured in a production mode
(i.e., with no spinlock or other debugging functions enabled; if you want to
save memory taken up by in-core inodes, the first thing you should do is
disable the debugging options; they are responsible for a huge amount of bloat
in the VFS inode structure).
This patch:
The filesystem or device-specific pointer in the inode is inside a union,
which is pretty pointless given that all 30+ users of this field have been
using the void pointer. Get rid of the union and rename it to i_private, with
a comment to explain who is allowed to use the void pointer. This is just a
cleanup, but it allows us to reuse the union 'u' for something something where
the union will actually be used.
[judith@osdl.org: powerpc build fix]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the problem that trying to enable already enabled
slot disables the slot by returning the proper value from
pciehp_enable_slot()/pciehp_disable_slot().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to assign resources to ioapics being hot-added. This patch
changes pbus_assign_resources_sorted() to assign resources if the
ioapic has no assigned resources.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently acpiphp calls pci_enable_device() against all
hot-added bridges, but acpiphp does not call pci_disable_device()
against them in hot-remove. So ioapic hot-remove would fail.
This patch fixes this issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Contrary to PCI bridge hot-add, we need to follow the sequence below
for PCI bridge hot-removal.
(1) Stop devices (detach drivers, remove from the global list, etc.)
(2) Unbind ACPI node from the devices (remove the _PRT entries)
(3) Remove devices (remove from the device list, etc.)
This patch fixes acpiphp driver to follow above sequence for P2P
bridge hot-removal.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds pci_stop_bus_device() which stops a PCI device (detach
the driver, remove from the global list and so on) and any children.
This is needed for ACPI based PCI-to-PCI bridge hot-remove, and it will
be also needed for ACPI based PCI root bridge hot-remove.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently acpiphp initializes all ioapics under the bus on which
hot-add event occured. It also initializes already working ioapics.
This patch fixes this bug.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently acpiphp initializes ioapics after starting devices,
but ioapics should be initialized before starting devices.
This patch fixes this bug.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently acpiphp sets hpp values after starting devices, but
the values should be set before starting devices. This patch
fixes this bug.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Restore PCI Express capability registers after PM event.
This includes maxumum MTU for PCI express and other vital data.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are numerous drivers that can use multithreaded probing but having
some kind of global flag as the way to control this makes migration to
threaded probing hard and since it enables it everywhere and is almost
as likely to cause serious pain as holding a clog dance in a minefield.
If we have a pci_driver multithread_probe flag to inherit you can turn
it on for one driver at a time.
From playing so far however I think we need a different model at the
device layer which serializes until the called probe function says "ok
you can start another one now". That would need some kind of flag and
semaphore plus a helper function.
Anyway in the absence of that this is a starting point to usefully play
with this stuff
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch 3 implements the core part of PCI-Express AER and aerdrv
port service driver.
When a root port service device is probed, the aerdrv will call
request_irq to register irq handler for AER error interrupt.
When a device sends an PCI-Express error message to the root port,
the root port will trigger an interrupt, by either MSI or IO-APIC,
then kernel would run the irq handler. The handler collects root
error status register and schedules a work. The work will call
the core part to process the error based on its type
(Correctable/non-fatal/fatal).
As for Correctable errors, the patch chooses to just clear the correctable
error status register of the device.
As for the non-fatal error, the patch follows generic PCI error handler
rules to call the error callback functions of the endpoint's driver. If
the device is a bridge, the patch chooses to broadcast the error to
downstream devices.
As for the fatal error, the patch resets the pci-express link and
follows generic PCI error handler rules to call the error callback
functions of the endpoint's driver. If the device is a bridge, the patch
chooses to broadcast the error to downstream devices.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Have pcie_port_bus_register() notice and return errors.
Mark it __must_check so that its caller(s) must check its return value.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduce msi_ht_cap_enabled() to check the MSI capability in the
Hypertransport configuration space.
It is used in a generic quirk quirk_msi_ht_cap() to check whether
MSI is enabled on hypertransport chipset, and a nVidia specific quirk
quirk_nvidia_ck804_msi_ht_cap() where two 2 HT MSI mappings have to
be checked.
Both quirks set the PCI_BUS_FLAGS_NO_MSI bus flag when MSI is disabled.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Export the PCI_BUS_FLAGS_NO_MSI flag of a PCI bus in the sysfs files
of its parent device and make it writable. Could be used to:
* disable MSI on a device which has not been blacklisted yet
* allow MSI when some setpci hacks enable MSI support (for instance
on the ServerWorks HT2000 chipset where the MSI HT cap is disabled
by default).
Architecture where some bus have no parent chipset cannot use this
strategy to change MSI support.
If the chipset does not have a subordinate bus, its 'bus_msi' file
is empty.
Also document and warn about the possible danger of changing the flag.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_enable_msi() and pci_enable_msix() use the same code to detect
whether MSI might be enabled on this device. Factorize this code in
pci_msi_supported(). And improve the documentation about the fact
that only the root chipset must support MSI, but it is hard to
find the root bus so we check all parent busses MSI flags.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move MSI quirks in CONFIG_PCI_MSI, document why the serverworks quirk
does not simply set PCI_BUS_FLAGS_NO_MSI, and create a generic quirk
for other chipsets where setting PCI_BUS_FLAGS_NO_MSI is fine.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (225 commits)
[PATCH] Don't set calgary iommu as default y
[PATCH] i386/x86-64: New Intel feature flags
[PATCH] x86: Add a cumulative thermal throttle event counter.
[PATCH] i386: Make the jiffies compares use the 64bit safe macros.
[PATCH] x86: Refactor thermal throttle processing
[PATCH] Add 64bit jiffies compares (for use with get_jiffies_64)
[PATCH] Fix unwinder warning in traps.c
[PATCH] x86: Allow disabling early pci scans with pci=noearly or disallowing conf1
[PATCH] x86: Move direct PCI scanning functions out of line
[PATCH] i386/x86-64: Make all early PCI scans dependent on CONFIG_PCI
[PATCH] Don't leak NT bit into next task
[PATCH] i386/x86-64: Work around gcc bug with noreturn functions in unwinder
[PATCH] Fix some broken white space in ia32_signal.c
[PATCH] Initialize argument registers for 32bit signal handlers.
[PATCH] Remove all traces of signal number conversion
[PATCH] Don't synchronize time reading on single core AMD systems
[PATCH] Remove outdated comment in x86-64 mmconfig code
[PATCH] Use string instructions for Core2 copy/clear
[PATCH] x86: - restore i8259A eoi status on resume
[PATCH] i386: Split multi-line printk in oops output.
...
Some buggy systems can machine check when config space accesses
happen for some non existent devices. i386/x86-64 do some early
device scans that might trigger this. Allow pci=noearly to disable
this. Also when type 1 is disabling also don't do any early
accesses which are always type1.
This moves the pci= configuration parsing to be a early parameter.
I don't think this can break anything because it only changes
a single global that is only used by PCI.
Cc: gregkh@suse.de
Cc: Trammell Hudson <hudson@osresearch.net>
Signed-off-by: Andi Kleen <ak@suse.de>
This provides a build and run-time option to turn on multhreaded probe
for all PCI drivers. It can cause bad problems on multi-processor
machines that take a while to find their root disks, and play havoc on
machines that don't use persistant device names for block or network
devices.
But it can cause speedups on some machines, my tiny laptop's boot goes
up by 0.4 seconds, and my desktop boots up several seconds faster.
Use at your own risk!!!
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sysfs_remove_bin_file() void. If it detects an error,
printk the file name and call dump_stack().
sysfs_hash_and_remove() now returns an error code indicating
its success or failure so that sysfs_remove_bin_file() can
know success/failure.
Convert the only driver that checked the return value of
sysfs_remove_bin_file().
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the new suspend_prepare() phase. It doesn't seem very usable,
has never been tested, doesn't address fault cleanup, and would need
a sibling resume_complete(); plus there are no real use cases. It
could be restored later if those issues get resolved.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert some framework code to handle the new PRETHAW message.
- IDE just treats it like a FREEZE.
- The pci_choose_state() thingie still doesn't use PCI_D0 when it gets a
FREEZE (and now PRETHAW) event, which seems rather buglike but wasn't
something to change with this patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Changes the PCI core to use the new suspend infrastructure changes.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch to add VIA PCI quirk for Enhanced/Extended USB on VT8235
southbridge. It is needed in order to use EHCI/USB 2.0 with ACPI.
Without it IRQs are not routed correctly, you get an "Unlink after
no-IRQ?" error and the device is unusable.
I belive this could also be a fix for Bugzilla Bug 5835.
Signed-off-by: Mark Hindley <mark@hindley.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removes an unused kerneldoc entry from pci_match_device and
put the others into correct order.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch against the CPCI hotplug core to fix up PCI resource
assignment such that things will actually work when a hot inserted
device is enabled. I mentioned this patch to you way back in April at
ELC, but am only now out from under things enough to clean it up and
submit it. I've basically cribbed the corresponding code from
shpchp_pci.c, so there are no big surprises. If it's still possible, I
wouldn't mind this going into 2.6.18, but it wouldn't be the end of the
world if it went into 2.6.19.
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- add the ICH6(R) LPC to the ICH6 ACPI quirks. currently only the ICH6-M
is handled. [ PCI_DEVICE_ID_INTEL_ICH6_1 is the ICH6-M LPC, ICH6_0 is
the ICH6(R) ]
- remove the wrong quirk calling asus_hides_smbus_lpc() for ICH6. the
register modified in asus_hides_smbus_lpc() has a different meaning in
ICH6.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/quirks.c was not updated when libata config constants were
renamed braking several libata quirks. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change the build options for acpiphp so that it may build without being
dependent on the ACPI_DOCK option, but yet does not allow the option of
acpiphp being built-in when dock is built as a module.
This does not change the previous patch for ACPI_IBM_DOCK Kconfig.
For the following matrix of config options, I built an i386 kernel.
Dock acpiphp should it build? confirmed
y y y y
y n y y
y m y y
m y no - acpiphp should acpiphp was
convert to m converted to m
m n y y
m m y y
n y y y
n n y y
n m y y
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Make pciehp build on powerpc
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unhide the SMBus controller on the Asus PU-DLS board.
This fixes bug #6763.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add acpiphp to the MAINTAINERS file.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If pcie_portdrv_probe() fails but it had already called
pci_enable_device(), then call pci_disable_device() when
returning error.
Is there some reason that this isn't being done?
or was it just missed?
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up kernel-doc comments in drivers/pci/search.c (line sizes and typos).
Enable that source file in DocBook/kernel-api.tmpl.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
pseries platform changes.
Built for pseries_defconfig
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Without this quirk, e100 can be pulling on a shared
interrupt line when another device (eg. USB) loads,
causing the interrupt to scream and get disabled.
http://bugzilla.kernel.org/show_bug.cgi?id=5918
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When changing power states from D0->DX and then from DX->D0, some
Intel PCIE chipsets will cause a device reset to occur. This will
cause problems for any D State other than D3, since any state
information that the driver will expect to be present coming from
a D1 or D2 state will have been cleared. This patch addes a
flag to the pci_dev structure to indicate that devices should
not use states D1 or D2, and will set that flag for the affected
chipsets. This patch also modifies pci_set_power_state() so that
when a device driver tries to set the power state on
a device that is downstream from an affected chipset, or on one
of the affected devices it only allows state changes to or
from D0 & D3. In addition, this patch allows the delay time
between D3->D0 to be changed via a quirk. These chipsets also
need additional time to change states beyond the normal 10ms.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some VIA southbridges contain a flag in the ACPI register space that
indicates whether an abnormal poweroff has occured, presumably with the
intention that it can be cleared on clean shutdown. Some BIOSes check this
flag at resume time, and will re-POST the system rather than jump back to
the OS if it's set. Clearing it at boot time appears to be sufficient.
I'm not sure if drivers/pci/quirks.c is the right place to do it, but I'm
not sure where would be cleaner.
[akpm@osdl.org: cleanups, build fix]
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg KH <greg@kroah.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: "Yu, Luming" <luming.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prior to 2.6.18rc1 you could install with devices on a JMicron chipset
using the "all-generic-ide" option. As of this kernel the AHCI driver
grabs the controller and rams it into AHCI mode losing the PATA ports
and making CD drives and the like vanish. The all-generic-ide option
fails because the AHCI driver grabbed the PCI device and reconfigured
it.
To fix this three things are needed.
#1 We must put the chip into dual function mode
#2 The AHCI driver must grab only function 0 (already in your rc1 tree)
#3 Something must grab the PATA ports
The attached patch is the minimal risk edition of this. It puts the chip
into dual function mode so that AHCI will grab the SATA ports without
losing the PATA ports. To keep the risk as low as possible the third
patch adds the PCI identifiers for the PATA port and the FN check to the
ide-generic driver. There is a more featured jmicron driver on its way
but that adds risk and the ide-generic support is sufficient to install
and run a system.
The actual chip setup done by the quirk is the precise setup recommended
by the vendor.
(The JMB368 appears only in the ide-generic entry as it has no AHCI so
does not need the quirk)
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It looks like someone confused kmem_cache_create with a different allocator
and was attempting to give it knowledge of how many cache entries there
were.
With the unfortunate result that each slab entry was big enough to hold
every irq.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is confirmed to fix a hang due to PCI resource conflicts with
setting up the Cardbus bridge on old laptops with the 440MX chipsets.
Original report by Alessio Sangalli, lspci debugging help by Pekka
Enberg, and trial patch suggested by Daniel Ritz:
"From the docs available i would _guess_ this thing is really similar
to the 82443BX/82371AB combination. at least the SMBus base address
register is hidden at the very same place (32bit at 0x90 in function
3 of the "south" brigde)"
The dang thing is largely undocumented, but the patch was corroborated
by Asit Mallick:
"I am trying to find the register information. 440MX is an integration of
440BX north-bridge without AGP and PIIX4E (82371EB). PIIX4 quirk
should cover the ACPI and SMBus related I/O registers."
and verified to fix the problem by Alessio.
Cc: Daniel Ritz <daniel.ritz-ml@swissonline.ch>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Tested-by: Alessio Sangalli <alesan@manoweb.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: ACPI_DOCK: Initialize the atomic notifier list
ACPI: acpi_os_allocate() fixes
ACPI: SBS: fix initialization, sem2mutex
ACPI: add 'const' to several ACPI file_operations
ACPI: delete some defaults from ACPI Kconfig
ACPI: "Device `[%s]' is not power manageable" make message debug only
ACPI: ACPI_DOCK Kconfig
Revert "Revert "ACPI: dock driver""
ACPI: acpi_os_get_thread_id() returns current
ACPI: ACPICA 20060707
The pci channel state is currently uninitialized, thus there are two ways
of indicating that "everything's OK": 0 and 1. This is a bit of a burden.
If a devce driver wants to check if the pci channel is in a working or a
disconnected state, the driver writer must perform checks similar to
if((pdev->error_state != 0) &&
(pdev->error_state != pci_channel_io_normal)) {
whatever();
}
which is rather akward. The first check is needed because stuct pci_dev is
inited to all-zeros. The scond is needed because the error recovery will
set the state to pci_channel_io_normal (which is not zero).
This patch fixes this awkwardness.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's useful to be able to turn off CONFIG_HOTPLUG for compile-coverage testing
and for section-checking coverage. But a few things go and select
CONFIG_HOTPLUG, making it a royal PITA to turn the thing off.
It's only turnable offable if CONFIG_EMBEDDED anyway. So let's make those
things depend on HOTPLUG, not select it.
Cc: Greg KH <greg@kroah.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HOTPLUG_PCI_ACPI depends on ACPI_DOCK
ACPI_IBM_DOCK depends on ACPI_DOCK=n
ACPI_DOCK is EXPERIMENTAL, though that doesn't seem to mean much
Signed-off-by: Len Brown <len.brown@intel.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
This patch-queue improves the generic IRQ layer to be truly generic, by adding
various abstractions and features to it, without impacting existing
functionality.
While the queue can be best described as "fix and improve everything in the
generic IRQ layer that we could think of", and thus it consists of many
smaller features and lots of cleanups, the one feature that stands out most is
the new 'irq chip' abstraction.
The irq-chip abstraction is about describing and coding and IRQ controller
driver by mapping its raw hardware capabilities [and quirks, if needed] in a
straightforward way, without having to think about "IRQ flow"
(level/edge/etc.) type of details.
This stands in contrast with the current 'irq-type' model of genirq
architectures, which 'mixes' raw hardware capabilities with 'flow' details.
The patchset supports both types of irq controller designs at once, and
converts i386 and x86_64 to the new irq-chip design.
As a bonus side-effect of the irq-chip approach, chained interrupt controllers
(master/slave PIC constructs, etc.) are now supported by design as well.
The end result of this patchset intends to be simpler architecture-level code
and more consolidation between architectures.
We reused many bits of code and many concepts from Russell King's ARM IRQ
layer, the merging of which was one of the motivations for this patchset.
This patch:
rename desc->handler to desc->chip.
Originally i did not want to do this, because it's a big patch. But having
both "desc->handler", "desc->handle_irq" and "action->handler" caused a
large degree of confusion and made the code appear alot less clean than it
truly is.
I have also attempted a dual approach as well by introducing a
desc->chip alias - but that just wasnt robust enough and broke
frequently.
So lets get over with this quickly. The conversion was done automatically
via scripts and converts all the code in the kernel.
This renaming patch is the first one amongst the patches, so that the
remaining patches can stay flexible and can be merged and split up
without having some big monolithic patch act as a merge barrier.
[akpm@osdl.org: build fix]
[akpm@osdl.org: another build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dock bridges generally do not implement _SUN, yet show up as ejectable
slots. If you have more than one ejectable slot that does not implement
SUN, with the current code you will get duplicate slot numbers. So, if
there is no _SUN, use the current count of the number of slots found
instead.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Modify the acpiphp driver to use the ACPI dock driver for dock
notifications. Only load the acpiphp driver if we find we have pci dock
devices.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
typo fixes
Clean up 'inline is not at beginning' warnings for usb storage
Storage class should be first
i386: Trivial typo fixes
ixj: make ixj_set_tone_off() static
spelling fixes
fix paniced->panicked typos
Spelling fixes for Documentation/atomic_ops.txt
move acknowledgment for Mark Adler to CREDITS
remove the bouncing email address of David Campbell
CC drivers/pci/msi-apic.o
In file included from include/asm/msi.h:11,
from drivers/pci/msi.h:71,
from drivers/pci/msi-apic.c:8:
include/asm/smp.h:103: error: syntax error before '->' token
akpm: nasty. It appears to be
static inline unsigned int cpu_mask_to_apicid(cpumask_t cpumask)
conflicting with include/asm-x86_64/mach_apic.h's
#define cpu_mask_to_apicid (genapic->cpu_mask_to_apicid)
And I don't know which patch in rc4-mm1 triggered this.
Fixing this in the .c file seems wrong.
Including asm/smp.h instead of linux/smp.h seems wrong too. Need that
.config.
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The nVidia CK804 PCI-E chipset supports the AER extended capability
but sometimes fails to link it (with some BIOS or after a warm reboot).
It makes the AER cap invisible to pci_find_ext_capability().
The patch adds a quirk to set the missing bit that controls the
linking of the capability.
By the way, it removes the corresponding code in the myri10ge driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Loic Prylli <loic@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From: Doug Thompson <norsk5@yahoo.com>
This patch adds the 'broken_parity_status' sysfs attribute file to a PCI device.
Reading this attribute a userland program can determine if PCI device provides false
positives (value of 1) in its generation of PCI Parity status, or not (value of 0).
As PCI devices are found to be 'bad' in this regard, userland programs can also set
the appropriate value (root access only) of a faulty device. This per device
information will be used in the EDAC PCI Parity scanner code in a future patch once
this interface becomes available.
Signed-off-by: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Be more selective when running the MSI-K8T-Neo2Fir soundcard PCI quirk so
as not to run this on hardware where it's probably not needed.
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_walk_bus has a race with pci_destroy_dev. When cb is called
in pci_walk_bus, pci_destroy_dev might unlink the dev pointed by next.
Later on in the next loop, pointer next becomes NULL and cause
kernel panic.
Below patch against 2.6.17-rc4 fixes it by changing pci_bus_lock (spin_lock)
to pci_bus_sem (rw_semaphore).
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code is really not needed.
Roland Dreier/Greg KH removed the release_mem_region() calls that
were the only consumers of phys_addr:
http://www.ussg.iu.edu/hypermail/linux/kernel/0503.0/1540.html
patch below deletes the "dead" code.
Signed-off-by: Grant Grundler <iod00d@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A recent Stratus x86_64 platform uses a system ioapic that is a PCI device
located below a PCI bridge. Other platforms like this may exist.
This patch fixes a problem wherein the kernel's PCI setup code moves
the ioapic to an address other than that assigned by the BIOS. It simply
adds another exclusion (which already includes classless devices and host
bridges) to the function pbus_assign_resources_sorted so that it will not
move the ioapic.
If the ioapic is moved, the fixmap mapping to it is broken, so the OS should
leave it alone.
From: Kimball Murray <kimball.murray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In IA64 platform, msi driver does not use irq_vector variable, and in
x86 platform LAST_DEVICE_VECTOR should one before FIRST_SYSTEM_VECTOR,
this patch modify this.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Brice said the pci_save_msi_state breaks his driver in his special usage
(not in suspend/resume), as pci_save_msi_state will disable msi mode. In
his usage, pci_save_state will be called at runtime, and later (after
the device operates for some time and has an error) pci_restore_state
will be called.
In another hand, suspend/resume needs disable msi mode, as device should
stop working completely. This patch try to workaround this issue.
Drivers are expected call pci_disable_device in suspend time after
pci_save_state.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We recently ran into a problem where the e1000 device failed to
work properly on the kexec kernel. MSI was enabled for the
device in the main kernel when it crashed. The e1000 driver
tried to enable MSI on the kexec kernel, but the code bailed
early when it found that MSI was already enabled in the hardware,
even though the software state was not properly set up in the
kexec'd kernel. This patch fixes the problem by moving the
early return to after making sure that the software state
is properly initialized.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI_BUS_FLAGS_NO_MSI bus flags does not appear do be inherited
correctly from the amd8131 MSI quirk to its parent busses. It makes
devices behind a bridge behind amd8131 try to enable MSI while the
amd8131 does not support it.
We fix this by looking at flags of all parent busses in
pci_enable_msi() and pci_enable_msix().
By the way, also add the missing dev->no_msi check in pci_enable_msix()
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, the EDAC (error detection and correction) modules that are in
the kernel contain some features that need to be moved. After some good
feedback on the PCI Parity detection code and interface
(http://www.ussg.iu.edu/hypermail/linux/kernel/0603.1/0897.html) this
patch ADDs an new attribute to the pci_dev structure: Namely the
'broken_parity_status' bit.
When set this indicates that the respective hardware generates false
positives of Parity errors.
The EDAC "blacklist" solution was inferior and will be removed in a
future patch.
Also in this patch is a PCI quirk.c entry for an Infiniband PCI-X card
which generates false positive parity errors.
I am requesting comments on this AND on the possibility of a exposing
this 'broken_parity_status' bit to userland via the PCI device sysfs
directory for devices. This access would allow for enabling of this
feature on new devices and for old devices that have their drivers
updated. (SLES 9 SP3 did this on an ATI motherboard video device). There
is a need to update such a PCI attribute between kernel releases.
This patch just adds a storage place for the attribute and a quirk entry
for a known bad PCI device. PCI Parity reaper/harvestor operations are
in EDAC itself and will be refactored to use this PCI attribute instead
of its own mechanisms (which are currently disabled) in the future.
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There were two instances of pci_acpi_init(), one in
drivers/pci/pci-acpi.c and another in arch/i386/pci/acpi.c.
Rename the one in pci-acpi.c and make it consistent with
other names in the same file.
Signed-off-by: Muthukumar R <muthur@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a device is already enabled, don't bother reenabling it.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Acked-By: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an "enable" sysfs attribute to each PCI device. When read it
shows the "enabled-ness" of the device, but you can write a "0" into it to
disable a device, and a "1" to enable it.
This later is needed for X and other cases where userspace wants to enable
the BARs on a device (typical example: to run the video bios on a secundary
head). Right now X does all this "by hand" via bitbanging, that's just evil.
This allows X to no longer do that but to just let the kernel do this.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
CC: Peter Jones <pjones@redhat.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI: Add pci_assign_resource_fixed -- allow fixed address assignments
On some embedded systems the PCI address for hotplug devices are not only
known a priori but are required to be at a given PCI address for other
master in the system to be able to access.
An example of such a system would be an FPGA which is setup from user space
after the system has booted. The FPGA may be access by DSPs in the system
and those DSPs expect the FPGA at a fixed PCI address.
Added pci_assign_resource_fixed() as a way to allow assignment of the PCI
devices's BARs at fixed PCI addresses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we detect a 64-bit pre-set address in a BAR on a 32-bit platform,
we disable it and treat it as if it had been unset, thus allowing the
general address assignment code to assign a new address to it when the
device is enabled. This can happen either if the firmware assigns
64-bit addresses; additionally, some cards have been found "in the
wild" which do not come out of reset with all the BAR registers set to
zero.
Unfortunately, the patch that implemented this tested the low part of
the address instead of the high part of the address. This patch fixes
that.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[pci] Ignore pre-set 64-bit BARs on 32-bit platforms
Currently, Linux always rejects a device which has a pre-set 64-bit
address on a 32-bit platform. On systems which do not do PCI
initialization in firmware, this causes some devices which don't
correctly power up with all BARs zero to fail.
This patch makes the kernel automatically zero out such an address
(thus treating it as if it had not been set at all, meaning it will
assign an address if necessary).
I have done this only for devices, not bridges. It seems potentially
hazardous to do for bridges.
Signed-off-by: H. Peter Anvin <hpa@c2micro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MSI callouts for altix. Involves a fair amount of code reorg in sn irq.c
code as well as adding some extensions to the altix PCI provider abstaction.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Abstract IA64_FIRST_DEVICE_VECTOR/IA64_LAST_DEVICE_VECTOR since SN platforms
use a subset of the IA64 range. Implement this by making the above macros
global variables which the platform can override in it setup code.
Also add a reserve_irq_vector() routine used by SN to mark a vector's as
in-use when that weren't allocated through assign_irq_vector().
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Abstract portions of the MSI core for platforms that do not use standard
APIC interrupt controllers. This is implemented through a new arch-specific
msi setup routine, and a set of msi ops which can be set on a per platform
basis.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove checks for value, since the hotplug core always provides
a valid value.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver shows device number of slots in info messages,
but it is useless and should be replaced with slot name.
This patch replaces the device number shown in the info messages with
the slot name.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes unused hpc_event_lock. This patch has no functional
change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the interrupt polling timer code in
shpchp_hpc.c. This has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code related to issuing SHPC commands. This
patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the interrupt handler of shpchp driver. This
patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements .get_address callback of hotplug_slot_ops for
PCIEHP driver. With this patch, we can see bus address of hotplug
slots as follows:
# cat /sys/bus/pci/slots/0010_0000/address
0000:0a:00
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch replaces pci_find_slot() with pci_get_slot() in PCIEHP
driver. This patch enables PCI Express Hotplug on the system which has
multiple PCI domains.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a repost of a patch submitted by Prarit Bhargava on 01-19-06 that
never got integrated.
The get_power_status function is currently reporting a bitwise mapping of
the slot if the slot is powered on. It should return 1 if powered on and
0 if powered off.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The workqueue thread of shpchp driver should be created only when SHPC
based hotplug slots are detected on the system.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Global SERR and Interrupt should be masked at shpchp driver unload time.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver doesn't take care of RsvdP/RsvdZ[*] bits in
controller SERR-INT register. This might cause unpredicable
results. This patch fixes this bug.
[*] RsvdP and RsvdZ are defined in SHPC spec as follows:
RsvdP - Reserved and Preserved. Register bits of this type are
reserved for future use as R/W bits. The value read is
undefined. Writes are ignored. Software must follow These rules
when accessing RsvdP bits:
- Software must ignore RsvdP bits when testing values read
from these registers.
- Software must not depend on RsvdP bit's ability to retain
information when written
- Software must always write back the value read in the RsvdP
bits when writing one of these registers.
RsvdZ - Reserved and Zero. Register bits of this type are reserved
for future use as R/WC bits. The value read is undefined. Writes
are ignored. Software must follow these rules when accessing RsvdZ
bits:
- Software must ignore RsvdZ bits when testing values read
from these registers.
- Software must not depends on a RsvdZ bit's ability to retain
information when written.
- Software must always write 0 to RsvdZ bits when writing one
of these register.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver doesn't take care of RsvdP/RsvdZ[*] bits
in logical slot registers. This might cause unpredicable results. This
patch fixes this bug.
[*] RsvdP and RsvdZ are defined in SHPC spec as follows:
RsvdP - Reserved and Preserved. Register bits of this type are
reserved for future use as R/W bits. The value read is
undefined. Writes are ignored. Software must follow These rules
when accessing RsvdP bits:
- Software must ignore RsvdP bits when testing values read
from these registers.
- Software must not depend on RsvdP bit's ability to retain
information when written
- Software must always write back the value read in the RsvdP
bits when writing one of these registers.
RsvdZ - Reserved and Zero. Register bits of this type are reserved
for future use as R/WC bits. The value read is undefined. Writes
are ignored. Software must follow these rules when accessing RsvdZ
bits:
- Software must ignore RsvdZ bits when testing values read
from these registers.
- Software must not depends on a RsvdZ bit's ability to retain
information when written.
- Software must always write 0 to RsvdZ bits when writing one
of these register.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code to access bits in slot logical
registers. This patch has no functional change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code to access slot logical registers. This
patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code to access SHPC working register
sets. This patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current PCHEHP driver doesn't have any code to program hotplug
parameters from firmware. So hotplug parameters are never programed at
hot-add time. This patch add support for programming hotplug
parameters to PCIEHP driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for _HPX (Hot Plug Parameter Extensions)
defined in ACPI3.0a spec.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the improper error message about OSHP evaluation
to debug message which is displayed only when pci_hotplug.ko is loaded
with debugging mode enabled. To do this, this patch adds a new module
parameter "debug_acpi" to pci_hotplug.ko for enabling/disabling debug
messages in acpi_pcihp.c.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that hotplug parameters are not programed
when PCI cards are hot-added by ACPIPHP, SHPCHP and PCIEHP driver. The
pci_dev structure being hot-added is not bound to ACPI handle, so we
need to trace PCI bus tree to find ACPI handle.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't call pci_enable_device from pciehp because the pcie port service driver
already does this.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
acpi_os_free should not be used by drivers outside
of acpi/*/*.c. Replace with kfree().
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When acpiphp_enable_slot() is failed, acpiphp does not change
the slot->flags. Therefore, when user tries to read power
status, acpiphp_get_power_status() returns the enable status
whether the slot is not really enabled.
This patch fixes this BUG.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I encountered the problem that when there are some hotplug
slots are under the host bridge, the hotplug slots under the
p2p bridge are not treated as hotpluggable.
This patch fixes this BUG.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
o hotplug slots add
When the hot-added PCI device is p2p bridge, acpiphp calls
find_p2p_bridge() to add hotplug slots.
o hotplug slots remove
When the hot-removing PCI device is p2p bridge, acpiphp
calls cleanup_p2p_bridge() to remove hotplug slots.
o notify handler exchange
When the p2p bridge is added, acpiphp changes the notify
hanlder.
If no bridge device is inserted into the hotpluggable PCI
slot, acpiphp installs the notify handler for function.
After the p2p bridge hot-add, acpiphp has to install the
notify handler for bridge. Because, the role of the
handlers are not same. The hot-remove case is ditto.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current acpiphp does not free acpi_device structs when the
PCI devices are removed. When the PCI device is added,
acpi_bus_add() fails because acpi_device struct has already
exists. So, _PRT method does not evaluate.
This patch fixes this issue.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SGI hotplug driver changes required to support Tollhouse system PCI
hotplug, and implements the PRF_HOTPLUG_SUPPORT feature bit.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
