The ralink_of_remap() function is repeated several times on SoC specific
source files. They have the same structure, but just differ in compatible
strings. In order to make commonly use of these codes, this patch
introduces a newly designed mtmips_of_remap_node() function to match and
remap all supported system controller and memory controller nodes.
Build and run tested on MT7620 and MT7628.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Usually, We only need to print the error log when there is a PCIe card but
initialization fails. Whether the driver finds the PCIe card or not is the
expected behavior. So it's better to log these information with dev_info().
Tested on MT7628AN router Motorola MWR03.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
These codes are used to read NFTS_TIMEOUT_DELAY register value and
write it into kernel log after writing the register. they are only
used for debugging during driver development, so there is no need
to keep them now.
Tested on MT7628AN router Motorola MWR03.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
At very early stage on boot, there is a need to set 'mips_hpt_frequency'.
This timer frequency is a half of the CPU frequency. To get clocks properly
set we need to call to 'of_clk_init()' and properly get cpu clock frequency
afterwards. Depending on the SoC, CPU clock index and compatible differs, so
use them to get the proper clock frm the clock provider. Hence, adapt code
to be aligned with new clock driver.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
A proper clock driver for ralink SoCs has been added. This driver is also
a reset provider for the SoC. Hence there is no need to have reset related
code in 'arch/mips/ralink' folder anymore. The only code that remains is
the one related with mips_reboot_setup where a PCI reset is performed.
We maintain this because I cannot test old ralink board with PCI to be
sure all works if we remove also this code.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
A proper clock driver for ralink SoCs has been added. Hence there is no
need to have clock related code in 'arch/mips/ralink' folder anymore.
Since this is the last clock related code removal, remove also remaining
prototypes in 'common.h' header file.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
A properly clock driver for ralink SoCs has been added. Hence there is no
need to have clock related code in 'arch/mips/ralink' folder anymore.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
A properly clock driver for ralink SoCs has been added. Hence there is no
need to have clock related code in 'arch/mips/ralink' folder anymore.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
A properly clock driver for ralink SoCs has been added. Hence there is no
need to have clock related code in 'arch/mips/ralink' folder anymore.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
While destroying alignment of the assignments in bridge_driver, do it
consistently and use a single space before =.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
As it's usuable on LS3A4000 platform. Tested with RX550, glmark2
got about 4235 score.
Signed-off-by: Sui Jingfeng <suijingfeng@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
After commit 96cb8ae28c ("MIPS: Rework smt cmdline parameters"),
modpost complains when building with clang:
WARNING: modpost: vmlinux.o: section mismatch in reference: core_vpe_count (section: .text) -> smp_max_threads (section: .init.data)
This warning occurs when core_vpe_count() is not inlined, as it appears
that a non-init function is referring to an init symbol. However, this
is not a problem in practice because core_vpe_count() is only called
from __init functions, cps_smp_setup() and cps_prepare_cpus().
Resolve the warning by marking core_vpe_count() as __init, as it is only
called in an init context so it can refer to init functions and symbols
and have its memory freed on boot.
Fixes: 96cb8ae28c ("MIPS: Rework smt cmdline parameters")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Macro cpu_has_mips_r2_exec_hazard correctly handles OCTEON CPUs,
so we don't need the extra switch cases for them.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
hlt,nohlt paramaters are useful when debugging cpuidle
related issues.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Provide a generic smt parameters interface aligned with s390
to allow users to limit smt usage and threads per core.
It replaced previous undocumented "nothreads" parameter for
smp-cps which is ambiguous and does not cover smp-mt.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Building with -Werror and W=1 fails entirely because of warnings in
asm-offsets.c:
arch/mips/kernel/asm-offsets.c:26:6: error: no previous prototype for 'output_ptreg_defines' [-Werror=missing-prototypes]
arch/mips/kernel/asm-offsets.c:78:6: error: no previous prototype for 'output_task_defines' [-Werror=missing-prototypes]
arch/mips/kernel/asm-offsets.c:92:6: error: no previous prototype for 'output_thread_info_defines' [-Werror=missing-prototypes]
arch/mips/kernel/asm-offsets.c:108:6: error: no previous prototype for 'output_thread_defines' [-Werror=missing-prototypes]
arch/mips/kernel/asm-offsets.c:136:6: error: no previous prototype for 'output_thread_fpu_defines' [-Werror=missing-prototypes]
Nothing actually calls these functions, so just add prototypes to shut
up the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Some CPU feature macros were using current_cpu_type to mark feature
availability.
However current_cpu_type will use smp_processor_id, which is prohibited
under preemptable context.
Since those features are all uniform on all CPUs in a SMP system, use
boot_cpu_type instead of current_cpu_type to fix preemptable kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This WiFi AP is based on a MT7621 SoC with 128MiB RAM, 128MiB NAND,
a MT7603 2.4GHz WiFi and a MT7613 5GHz WiFi chips integrated on the board,
connected to the main SoC over PCIe.
The device uses NMBM over NAND, which is not currently supported in the
mainline, so NAND node is skipped in this revision.
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Enable the required drivers for the WiFi / Bluetooth functionality.
I enabled WEXT compatibility as well since the CI20 is typically used
with a very old userspace.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Just a "make ci20_defconfig menuconfig savedefconfig"
Without changing anything in the menuconfig. No functional change.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Wire the WiFi/Bluetooth chip properly in the Device Tree.
- Provide it with the correct regulators and clocks;
- Change the MMC I/O bus to 1.8V which seems to be enough;
- Change the MMC I/O bus frequency to 25 MHz as 50 MHz causes errors;
- Fix the Bluetooth powerdown GPIO being inverted and add reset GPIO;
- Convert host-wakeup-gpios to IRQ.
With these changes, the WiFi works properly with the latest firmware
provided by linux-firmware. The Bluetooth does not work very well here,
as I cannot get my wireless keyboard to pair; but it does detect it, and
it does see the key presses when I type the pairing code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This makes it possible to clock the SD cards much higher, as the MPLL is
running at 1.2 GHz by default. The previous parent was the EXT clock,
which caused the SD cards to be clocked at 24 MHz maximum.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- Use the standard "ecc-engine" property instead of the custom
"ingenic,bch-controller" to get a handle to the BCH controller.
- Respect cell sizes in the Ethernet controller node.
- Use proper macro for interrupt type instead of hardcoding magic
values.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
These regulators should be enabled by their respective drivers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Provide parent regulators to the ACT8600 regulators that need one.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The Device Tree was using invalid node names for the ACT8600 regulators.
To be fair, it is not the original committer's fault, as the
documentation did gives invalid names as well.
In theory, the fix should have been to modify the driver to accept the
alternative names. However, even though the act8865 driver spits
warnings, the kernel seemed to work fine with what is currently
supported upstream. For that reason, I think it is okay to just update
the DTS.
I removed the "regulator-name" too, since they really didn't bring any
information. The node names are enough.
Fixes: 73f2b94047 ("MIPS: CI20: DTS: Add I2C nodes")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The regulators don't have any "reg" property, and therefore shouldn't
use an unit address in their node names. They also don't need to specify
the GPIO_ACTIVE_LOW flag, which will be ignored anyway, as they are
active-high.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The regulators don't have any "reg" property, and therefore shouldn't
use an unit address in their node names.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The JZ4750, JZ4755 and JZ4760 (non-B version) support using a 24 MHz
external crystal oscillator instead of the typical 12 MHz one.
However, most of the SoC's IP blocks only work with a 12 MHz clock.
Thanksfully, there is a /2 divider we can enable when a 24 MHz external
crystal is present.
Force-enable this /2 divider when the oscillator is 24 MHz, so that the
SoC always uses a 12 MHz clock internally.
It is done here, and not in the clocks driver, because we need the EXT
clock to be 12 MHz for the early console to work, and the clocks driver
probes way too late.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
These flags are useless in this case as the code referencing these data
structures is always seen by the compiler (and not behind #ifdef
guards).
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The LXW, LXH, LXHU opcodes are part of the MXU ASE found in Ingenic
XBurst based SoCs.
While technically part of the MXU ASE, they do not touch any of the SIMD
registers, and can be used even when the MXU ASE is disabled.
This patch makes it possible to emulate unaligned access for those
instructions.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Revert commit 75b18aac6f ("MIPS: unhide PATA_PLATFORM") now that
HAVE_PATA_PLATFORM is set selectively for all the relevant platforms.
Verified with `db1xxx_defconfig' and `sb1250_swarm_defconfig' by making
sure PATA_PLATFORM is still there in `.config' with this change applied,
and with `malta_defconfig' by making sure it's now gone.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
We have limited demand for platform PATA support across MIPS platforms:
$ find arch/mips -type f | sort | xargs grep -l pata_platform_info
arch/mips/alchemy/devboards/db1200.c
arch/mips/alchemy/devboards/db1300.c
arch/mips/sibyte/swarm/platform.c
$
certainly not high enough to justify enabling support for PATA_PLATFORM
port-wide. SiByte platforms are handled selectively already, so just
make a similar arrangement for Alchemy DB1XXX platforms.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix some indentation issues and remove the following checkpatch issue:
- ERROR: need consistent spacing around '-' (ctx:WxV)
Co-Developed-by: Ladislav Michl <oss-lists@triops.cz>
Signed-off-by: Franziska Naepelt <franziska.naepelt@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Since we do have P5600 bitfile for boston board, we should
allow generic kernel to be compiled for R5 CPUs.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The unxlate_dev_mem_ptr() function has no prototype on the mips
architecture, which does not include asm-generic/io.h, so gcc warns
about the __weak definition:
drivers/char/mem.c:94:29: error: no previous prototype for 'unxlate_dev_mem_ptr' [-Werror=missing-prototypes]
Since everyone else already gets the generic definition or has a custom
one, there is not really much point in having a __weak version as well.
Remove this one, and instead add a trivial macro to the mips header.
Once we convert mips to use the asm-generic header, this can go away
again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
PAGE_OFFSET is technically a virtual address so when checking the value of
initrd_start against it we should make sure that it has been sanitised from
the values passed by the bootloader. Without this change, even with a bootloader
that passes correct addresses for an initrd, we are failing to load it on MT7621
boards, for example.
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Various fixes for the Au1200/Au1550/Au1300 DBDMA2 code:
- skip cache invalidation if chip has working coherency circuitry.
- invalidate KSEG0-portion of the (physical) data address.
- force the dma channel doorbell write out to bus immediately with
a sync.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The Au1300, at least the one I have to test, uses the NetLogic vendor
ID, but commit 95b8a5e011 ("MIPS: Remove NETLOGIC support") also
dropped Au1300 detection. Restore Au1300 detection.
Tested on DB1300 with Au1380 chip.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Alchemy DB1200/DB1300 boards can use the pata_platform driver.
Unhide the config entry in all of MIPS.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add a node for the on-board I2S audio controller.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Commit 2a31bf2080 ("watchdog: loongson1_wdt: Implement restart handler")
implmented .restart ops, Then, _machine_restart is no longer needed.
The _machine_halt and pm_power_off are also unnecessary,
which contain no hardware operations.
Therefore, remove the entire reset.c and related header file.
Update the Makefile accordingly.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The "ext" and "pll half" clocks don't belong in the DT. They are
not consumed directly by the AIC and are only used as the parent
clocks of the "i2s" clock. An operating system should be able to
figure out that information itself because it presumably knows the
layout of the clock tree.
Removing these from the DT should be safe from a compatibility
point of view because the jz4740-i2s driver in Linux does not, and
never did depend on them.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/all/20221028103418.17578-1-aidanmacdonald.0x0@gmail.com/
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- Introduce local{,64}_try_cmpxchg() - a slightly more optimal
primitive, which will be used in perf events ring-buffer code.
- Simplify/modify rwsems on PREEMPT_RT, to address writer starvation.
- Misc cleanups/fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=mM0A
-----END PGP SIGNATURE-----
Merge tag 'locking-core-2023-05-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
- Introduce local{,64}_try_cmpxchg() - a slightly more optimal
primitive, which will be used in perf events ring-buffer code
- Simplify/modify rwsems on PREEMPT_RT, to address writer starvation
- Misc cleanups/fixes
* tag 'locking-core-2023-05-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/atomic: Correct (cmp)xchg() instrumentation
locking/x86: Define arch_try_cmpxchg_local()
locking/arch: Wire up local_try_cmpxchg()
locking/generic: Wire up local{,64}_try_cmpxchg()
locking/atomic: Add generic try_cmpxchg{,64}_local() support
locking/rwbase: Mitigate indefinite writer starvation
locking/arch: Rename all internal __xchg() names to __arch_xchg()
* More phys_to_virt conversions
* Improvement of AP management for VSIE (nested virtualization)
ARM64:
* Numerous fixes for the pathological lock inversion issue that
plagued KVM/arm64 since... forever.
* New framework allowing SMCCC-compliant hypercalls to be forwarded
to userspace, hopefully paving the way for some more features
being moved to VMMs rather than be implemented in the kernel.
* Large rework of the timer code to allow a VM-wide offset to be
applied to both virtual and physical counters as well as a
per-timer, per-vcpu offset that complements the global one.
This last part allows the NV timer code to be implemented on
top.
* A small set of fixes to make sure that we don't change anything
affecting the EL1&0 translation regime just after having having
taken an exception to EL2 until we have executed a DSB. This
ensures that speculative walks started in EL1&0 have completed.
* The usual selftest fixes and improvements.
KVM x86 changes for 6.4:
* Optimize CR0.WP toggling by avoiding an MMU reload when TDP is enabled,
and by giving the guest control of CR0.WP when EPT is enabled on VMX
(VMX-only because SVM doesn't support per-bit controls)
* Add CR0/CR4 helpers to query single bits, and clean up related code
where KVM was interpreting kvm_read_cr4_bits()'s "unsigned long" return
as a bool
* Move AMD_PSFD to cpufeatures.h and purge KVM's definition
* Avoid unnecessary writes+flushes when the guest is only adding new PTEs
* Overhaul .sync_page() and .invlpg() to utilize .sync_page()'s optimizations
when emulating invalidations
* Clean up the range-based flushing APIs
* Revamp the TDP MMU's reaping of Accessed/Dirty bits to clear a single
A/D bit using a LOCK AND instead of XCHG, and skip all of the "handle
changed SPTE" overhead associated with writing the entire entry
* Track the number of "tail" entries in a pte_list_desc to avoid having
to walk (potentially) all descriptors during insertion and deletion,
which gets quite expensive if the guest is spamming fork()
* Disallow virtualizing legacy LBRs if architectural LBRs are available,
the two are mutually exclusive in hardware
* Disallow writes to immutable feature MSRs (notably PERF_CAPABILITIES)
after KVM_RUN, similar to CPUID features
* Overhaul the vmx_pmu_caps selftest to better validate PERF_CAPABILITIES
* Apply PMU filters to emulated events and add test coverage to the
pmu_event_filter selftest
x86 AMD:
* Add support for virtual NMIs
* Fixes for edge cases related to virtual interrupts
x86 Intel:
* Don't advertise XTILE_CFG in KVM_GET_SUPPORTED_CPUID if XTILE_DATA is
not being reported due to userspace not opting in via prctl()
* Fix a bug in emulation of ENCLS in compatibility mode
* Allow emulation of NOP and PAUSE for L2
* AMX selftests improvements
* Misc cleanups
MIPS:
* Constify MIPS's internal callbacks (a leftover from the hardware enabling
rework that landed in 6.3)
Generic:
* Drop unnecessary casts from "void *" throughout kvm_main.c
* Tweak the layout of "struct kvm_mmu_memory_cache" to shrink the struct
size by 8 bytes on 64-bit kernels by utilizing a padding hole
Documentation:
* Fix goof introduced by the conversion to rST
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmRNExkUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNyjwf+MkzDael9y9AsOZoqhEZ5OsfQYJ32
Im5ZVYsPRU2K5TuoWql6meIihgclCj1iIU32qYHa2F1WYt2rZ72rJp+HoY8b+TaI
WvF0pvNtqQyg3iEKUBKPA4xQ6mj7RpQBw86qqiCHmlfNt0zxluEGEPxH8xrWcfhC
huDQ+NUOdU7fmJ3rqGitCvkUbCuZNkw3aNPR8dhU8RAWrwRzP2hBOmdxIeo81WWY
XMEpJSijbGpXL9CvM0Jz9nOuMJwZwCCBGxg1vSQq0xTfLySNMxzvWZC2GFaBjucb
j0UOQ7yE0drIZDVhd3sdNslubXXU6FcSEzacGQb9aigMUon3Tem9SHi7Kw==
=S2Hq
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"s390:
- More phys_to_virt conversions
- Improvement of AP management for VSIE (nested virtualization)
ARM64:
- Numerous fixes for the pathological lock inversion issue that
plagued KVM/arm64 since... forever.
- New framework allowing SMCCC-compliant hypercalls to be forwarded
to userspace, hopefully paving the way for some more features being
moved to VMMs rather than be implemented in the kernel.
- Large rework of the timer code to allow a VM-wide offset to be
applied to both virtual and physical counters as well as a
per-timer, per-vcpu offset that complements the global one. This
last part allows the NV timer code to be implemented on top.
- A small set of fixes to make sure that we don't change anything
affecting the EL1&0 translation regime just after having having
taken an exception to EL2 until we have executed a DSB. This
ensures that speculative walks started in EL1&0 have completed.
- The usual selftest fixes and improvements.
x86:
- Optimize CR0.WP toggling by avoiding an MMU reload when TDP is
enabled, and by giving the guest control of CR0.WP when EPT is
enabled on VMX (VMX-only because SVM doesn't support per-bit
controls)
- Add CR0/CR4 helpers to query single bits, and clean up related code
where KVM was interpreting kvm_read_cr4_bits()'s "unsigned long"
return as a bool
- Move AMD_PSFD to cpufeatures.h and purge KVM's definition
- Avoid unnecessary writes+flushes when the guest is only adding new
PTEs
- Overhaul .sync_page() and .invlpg() to utilize .sync_page()'s
optimizations when emulating invalidations
- Clean up the range-based flushing APIs
- Revamp the TDP MMU's reaping of Accessed/Dirty bits to clear a
single A/D bit using a LOCK AND instead of XCHG, and skip all of
the "handle changed SPTE" overhead associated with writing the
entire entry
- Track the number of "tail" entries in a pte_list_desc to avoid
having to walk (potentially) all descriptors during insertion and
deletion, which gets quite expensive if the guest is spamming
fork()
- Disallow virtualizing legacy LBRs if architectural LBRs are
available, the two are mutually exclusive in hardware
- Disallow writes to immutable feature MSRs (notably
PERF_CAPABILITIES) after KVM_RUN, similar to CPUID features
- Overhaul the vmx_pmu_caps selftest to better validate
PERF_CAPABILITIES
- Apply PMU filters to emulated events and add test coverage to the
pmu_event_filter selftest
- AMD SVM:
- Add support for virtual NMIs
- Fixes for edge cases related to virtual interrupts
- Intel AMX:
- Don't advertise XTILE_CFG in KVM_GET_SUPPORTED_CPUID if
XTILE_DATA is not being reported due to userspace not opting in
via prctl()
- Fix a bug in emulation of ENCLS in compatibility mode
- Allow emulation of NOP and PAUSE for L2
- AMX selftests improvements
- Misc cleanups
MIPS:
- Constify MIPS's internal callbacks (a leftover from the hardware
enabling rework that landed in 6.3)
Generic:
- Drop unnecessary casts from "void *" throughout kvm_main.c
- Tweak the layout of "struct kvm_mmu_memory_cache" to shrink the
struct size by 8 bytes on 64-bit kernels by utilizing a padding
hole
Documentation:
- Fix goof introduced by the conversion to rST"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (211 commits)
KVM: s390: pci: fix virtual-physical confusion on module unload/load
KVM: s390: vsie: clarifications on setting the APCB
KVM: s390: interrupt: fix virtual-physical confusion for next alert GISA
KVM: arm64: Have kvm_psci_vcpu_on() use WRITE_ONCE() to update mp_state
KVM: arm64: Acquire mp_state_lock in kvm_arch_vcpu_ioctl_vcpu_init()
KVM: selftests: Test the PMU event "Instructions retired"
KVM: selftests: Copy full counter values from guest in PMU event filter test
KVM: selftests: Use error codes to signal errors in PMU event filter test
KVM: selftests: Print detailed info in PMU event filter asserts
KVM: selftests: Add helpers for PMC asserts in PMU event filter test
KVM: selftests: Add a common helper for the PMU event filter guest code
KVM: selftests: Fix spelling mistake "perrmited" -> "permitted"
KVM: arm64: vhe: Drop extra isb() on guest exit
KVM: arm64: vhe: Synchronise with page table walker on MMU update
KVM: arm64: pkvm: Document the side effects of kvm_flush_dcache_to_poc()
KVM: arm64: nvhe: Synchronise with page table walker on TLBI
KVM: arm64: Handle 32bit CNTPCTSS traps
KVM: arm64: nvhe: Synchronise with page table walker on vcpu run
KVM: arm64: vgic: Don't acquire its_lock before config_lock
KVM: selftests: Add test to verify KVM's supported XCR0
...
are a couple patches to the core clk framework, but they're all basically
cleanups or debugging aids. The driver updates and new additions are dominated
in the diffstat by Qualcomm and MediaTek drivers. Qualcomm gained a handful of
new drivers for various SoCs, and MediaTek gained a bunch of drivers for
MT8188. The MediaTek drivers are being modernized as well, so there are
updates all over that vendor's clk drivers. There's also a couple other new clk
drivers in here, for example the Starfive JH7110 SoC support is added.
Outside of the two major SoC vendors though, we have the usual collection of
non-critical fixes and cleanups to various clk drivers. It's good to see that
we're getting more cleanups and modernization patches. Maybe one day we'll be
able to properly split clk providers from clk consumers.
Core:
- Print an informational message before disabling unused clks
New Drivers:
- BCM63268 timer clock and reset controller
- Frequency Hopping (FHCTL) on MediaTek MT6795, MT8173, MT8192 and
MT8195 SoCs
- Mediatek MT8188 SoC clk drivers
- Clock driver for Sunplus SP7021 SoC
- Clk driver support for Loongson-2 SoCs
- Clock driver for Skyworks Si521xx I2C PCIe clock generators
- Initial Starfive JH7110 clk/reset support
- Global clock controller drivers for Qualcomm SM7150, IPQ9574, MSM8917 and IPQ5332 SoCs
- GPU clock controller drivers for SM6115, SM6125, SM6375 and SA8775P SoCs
Updates:
- Shrink size of clk_fractional_divider a little
- Convert various clk drivers to devm_of_clk_add_hw_provider()
- Convert platform clk drivers to remove_new()
- Converted most Mediatek clock drivers to struct platform_driver
- MediaTek clock drivers can be built as modules
- Reimplement Loongson-1 clk driver with DT support
- Migrate socfpga clk driver to of_clk_add_hw_provider()
- Support for i3c clks on Aspeed ast2600 SoCs
- Add clock generic devm_clk_hw_register_gate_parent_data
- Add audiomix block control for i.MX8MP
- Add support for determine_rate to i.MX composite-8m
- Let the LCDIF Pixel clock of i.MX8MM and i.MX8MN set parent rate
- Provide clock name in error message for clk-gpr-mux on get parent failure
- Drop duplicate imx_clk_mux_flags macro
- Register the i.MX8MP Media Disp2 Pix clock as bus clock
- Add Media LDB root clock to i.MX8MP
- Make i.MX8MP nand_usdhc_bus clock as non-critical
- Fix the rate table for i.MX fracn-gppll
- Disable HW control for the fracn-gppll in order to be controlled by
register write
- Add support for interger PLL in fracn-gppll
- Add mcore_booted module parameter to i.MX93 provider
- Add NIC, A55 and ARM PLL clocks to i.MX93
- Fix i.MX8ULP XBAR_DIVBUS and AD_SLOW clock parents
- Use "divider closest" clock type for PLL4_PFD dividers on i.MX8ULP to
get more accurate clock rates
- Mark the MU0_Bi and TPM5 clocks on i.MX8ULP as critical
- Update some of the i.MX critical clocks flags to allow glitchless
on-the-fly rate change.
- Add I2C5 clock on Renesas R-Car V3H
- Exynos850: Add CMU_G3D clock controller for the Mali GPU
- Extract Exynos5433 (ARM64) clock controller power management code to
common driver parts
- Exynos850: make PMU_ALIVE_PCLK clock critical
- Add Audio, thermal, camera (CSI-2), Image Signal Processor/Channel
Selector (ISPCS), and video capture (VIN) clocks on Renesas R-Car V4H
- Add video capture (VIN) clocks on Renesas R-Car V3H
- Add Cortex-A53 System CPU (Z2) clocks on Renesas R-Car V3M and V3H
- Support for Stromer Plus PLL on Qualcomm IPQ5332
- Add a missing reset to Qualcomm QCM2290
- Migrate Qualcomm IPQ4019 to clk_parent_data
- Make USB GDSCs enter retention state when disabled on Qualcomm SM6375,
MSM8996 and MSM8998 SoCs
- Set floor rounding clk_ops for Qualcomm QCM2290 SDCC2 clk
- Add two EMAC GDSCs on Qualcomm SC8280XP
- Use shared rcg clk ops in Qualcomm SM6115 GCC
- Park Qualcomm SM8350 PCIe PIPE clks when disabled
- Add GDSCs to Qualcomm SC7280 LPASS audio clock controller
- Add missing XO clocks to Qualcomm MSM8226 and MSM8974
- Convert some Qualcomm clk DT bindings to YAML
- Reparenting fix for the clock supplying camera modules on Rockchip rk3399
- Mark more critical (bus-)clocks on Rockchip rk3588
-----BEGIN PGP SIGNATURE-----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=bTtL
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Nothing looks out of the ordinary in this batch of clk driver updates.
There are a couple patches to the core clk framework, but they're all
basically cleanups or debugging aids. The driver updates and new
additions are dominated in the diffstat by Qualcomm and MediaTek
drivers. Qualcomm gained a handful of new drivers for various SoCs,
and MediaTek gained a bunch of drivers for MT8188. The MediaTek
drivers are being modernized as well, so there are updates all over
that vendor's clk drivers. There's also a couple other new clk drivers
in here, for example the Starfive JH7110 SoC support is added.
Outside of the two major SoC vendors though, we have the usual
collection of non-critical fixes and cleanups to various clk drivers.
It's good to see that we're getting more cleanups and modernization
patches. Maybe one day we'll be able to properly split clk providers
from clk consumers.
Core:
- Print an informational message before disabling unused clks
New Drivers:
- BCM63268 timer clock and reset controller
- Frequency Hopping (FHCTL) on MediaTek MT6795, MT8173, MT8192 and
MT8195 SoCs
- Mediatek MT8188 SoC clk drivers
- Clock driver for Sunplus SP7021 SoC
- Clk driver support for Loongson-2 SoCs
- Clock driver for Skyworks Si521xx I2C PCIe clock generators
- Initial Starfive JH7110 clk/reset support
- Global clock controller drivers for Qualcomm SM7150, IPQ9574,
MSM8917 and IPQ5332 SoCs
- GPU clock controller drivers for SM6115, SM6125, SM6375 and SA8775P
SoCs
Updates:
- Shrink size of clk_fractional_divider a little
- Convert various clk drivers to devm_of_clk_add_hw_provider()
- Convert platform clk drivers to remove_new()
- Converted most Mediatek clock drivers to struct platform_driver
- MediaTek clock drivers can be built as modules
- Reimplement Loongson-1 clk driver with DT support
- Migrate socfpga clk driver to of_clk_add_hw_provider()
- Support for i3c clks on Aspeed ast2600 SoCs
- Add clock generic devm_clk_hw_register_gate_parent_data
- Add audiomix block control for i.MX8MP
- Add support for determine_rate to i.MX composite-8m
- Let the LCDIF Pixel clock of i.MX8MM and i.MX8MN set parent rate
- Provide clock name in error message for clk-gpr-mux on get parent
failure
- Drop duplicate imx_clk_mux_flags macro
- Register the i.MX8MP Media Disp2 Pix clock as bus clock
- Add Media LDB root clock to i.MX8MP
- Make i.MX8MP nand_usdhc_bus clock as non-critical
- Fix the rate table for i.MX fracn-gppll
- Disable HW control for the fracn-gppll in order to be controlled by
register write
- Add support for interger PLL in fracn-gppll
- Add mcore_booted module parameter to i.MX93 provider
- Add NIC, A55 and ARM PLL clocks to i.MX93
- Fix i.MX8ULP XBAR_DIVBUS and AD_SLOW clock parents
- Use "divider closest" clock type for PLL4_PFD dividers on i.MX8ULP
to get more accurate clock rates
- Mark the MU0_Bi and TPM5 clocks on i.MX8ULP as critical
- Update some of the i.MX critical clocks flags to allow glitchless
on-the-fly rate change.
- Add I2C5 clock on Renesas R-Car V3H
- Exynos850: Add CMU_G3D clock controller for the Mali GPU
- Extract Exynos5433 (ARM64) clock controller power management code
to common driver parts
- Exynos850: make PMU_ALIVE_PCLK clock critical
- Add Audio, thermal, camera (CSI-2), Image Signal Processor/Channel
Selector (ISPCS), and video capture (VIN) clocks on Renesas R-Car
V4H
- Add video capture (VIN) clocks on Renesas R-Car V3H
- Add Cortex-A53 System CPU (Z2) clocks on Renesas R-Car V3M and V3H
- Support for Stromer Plus PLL on Qualcomm IPQ5332
- Add a missing reset to Qualcomm QCM2290
- Migrate Qualcomm IPQ4019 to clk_parent_data
- Make USB GDSCs enter retention state when disabled on Qualcomm
SM6375, MSM8996 and MSM8998 SoCs
- Set floor rounding clk_ops for Qualcomm QCM2290 SDCC2 clk
- Add two EMAC GDSCs on Qualcomm SC8280XP
- Use shared rcg clk ops in Qualcomm SM6115 GCC
- Park Qualcomm SM8350 PCIe PIPE clks when disabled
- Add GDSCs to Qualcomm SC7280 LPASS audio clock controller
- Add missing XO clocks to Qualcomm MSM8226 and MSM8974
- Convert some Qualcomm clk DT bindings to YAML
- Reparenting fix for the clock supplying camera modules on Rockchip
rk3399
- Mark more critical (bus-)clocks on Rockchip rk3588"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (290 commits)
clk: qcom: gcc-sc8280xp: Add EMAC GDSCs
clk: starfive: Delete the redundant dev_set_drvdata() in JH7110 clock drivers
clk: rockchip: rk3588: make gate linked clocks critical
clk: qcom: dispcc-qcm2290: Remove inexistent DSI1PHY clk
clk: qcom: add the GPUCC driver for sa8775p
dt-bindings: clock: qcom: describe the GPUCC clock for SA8775P
clk: qcom: gcc-sm8350: fix PCIe PIPE clocks handling
clk: qcom: lpassaudiocc-sc7280: Add required gdsc power domain clks in lpass_cc_sc7280_desc
clk: qcom: lpasscc-sc7280: Skip qdsp6ss clock registration
dt-bindings: clock: qcom,sc7280-lpasscc: Add qcom,adsp-pil-mode property
clk: starfive: Avoid casting iomem pointers
clk: microchip: fix potential UAF in auxdev release callback
clk: qcom: rpm: Use managed `of_clk_add_hw_provider()`
clk: mediatek: fhctl: Mark local variables static
clk: sifive: make SiFive clk drivers depend on ARCH_ symbols
clk: uniphier: Use managed `of_clk_add_hw_provider()`
clk: si5351: Use managed `of_clk_add_hw_provider()`
clk: si570: Use managed `of_clk_add_hw_provider()`
clk: si514: Use managed `of_clk_add_hw_provider()`
clk: lmk04832: Use managed `of_clk_add_hw_provider()`
...
Implement target specific support for local_try_cmpxchg()
and local_cmpxchg() using typed C wrappers that call their
_local counterpart and provide additional checking of
their input arguments.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230405141710.3551-4-ubizjak@gmail.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Decrease the probability of this internal facility to be used by
driver code.
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Palmer Dabbelt <palmer@rivosinc.com> [riscv]
Link: https://lore.kernel.org/r/20230118154450.73842-1-andrzej.hajda@intel.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
