When DVS is enabled via the devicetree properties
"nxp,dvs-run-voltage" and "nxp,dvs-standby-voltage" then
also the bit that enables DVS control via PMIC_STBY_REQ pin
should be set.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-5-rickaran@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The default configuration of the PMIC behavior makes the PMIC
power cycle most regulators on WDOG_B assertion. This power
cycling causes the memory contents of OCRAM to be lost.
Some systems neeeds some memory that survives reset and
reboot, therefore this patch is created.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-4-rickaran@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the I2C Level Translator included in PCA9450 configurable from
devicetree. The reset state is off. By setting nxp,i2c-lt-enable, the
I2C Level Translator will be enabled while in STANDBY or RUN state.
Signed-off-by: Per-Daniel Olsson <perdo@axis.com>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-2-rickaran@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver uses the DVS registers PCA9450_REG_BUCKxOUT_DVS0 to set the
voltage for the buck regulators 1, 2 and 3. This has no effect as the
PRESET_EN bit is set by default and therefore the preset values are used
instead, which are set to 850 mV.
To fix this we clear the PRESET_EN bit at time of initialization.
Fixes: 0935ff5f1f ("regulator: pca9450: add pca9450 pmic driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210222115229.166620-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes the return value of pca9450_i2c_probe() to use the correct
error code when getting the sd-vsel GPIO fails.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210222150809.208942-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
By default the PCA9450 doesn't handle the assertion of the WDOG_B
signal, but this is required to guarantee that things like software
resets triggered by the watchdog work reliably.
As we don't want to rely on the bootloader to enable this, we tell
the PMIC to issue a cold reset in case the WDOG_B signal is
asserted (WDOG_B_CFG = 10), just as the NXP U-Boot code does.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210211105534.38972-3-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
LDO5 has two separate control registers. LDO5CTRL_L is used if the
input signal SD_VSEL is low and LDO5CTRL_H if it is high.
The current driver implementation only uses LDO5CTRL_H. To make this
work on boards that have SD_VSEL connected to a GPIO, we add support
for specifying an optional GPIO and setting it to high at probe time.
In the future we might also want to add support for boards that have
SD_VSEL set to a fixed low level. In this case we need to change the
driver to be able to use the LDO5CTRL_L register.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210211105534.38972-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usages of these is to assign their address to the ops field in
the regulator_desc struct, which is a const pointer. Make them const to
allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200913084114.8851-5-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
