1. new skb only need dst and ip address(v4 or v6).
2. skb_copy may need high order pages, which is very rare on long running server.
Signed-off-by: Junwei Zhang <linggao.zjw@alibaba-inc.com>
Signed-off-by: Martin Zhang <martinbj2008@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PAGE_ALIGNED(...) instead of open-coding it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
rb->frames_per_block is an unsigned int, thus can never be negative.
Also fix spacing in the calculation of frames_per_block.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NOLINK state will poll the phy once a second to see if the link
has come up. If the phy has an interrupt line, this polling can be
skipped, since the phy should interrupt when the link returns.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E1540 can be found embedded in the Marvell 88E6352 switch. It
is compatible with the 88E1510, so add support for it, using the
88E1510 specific functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save and restore FP/LR in BPF prog prologue and epilogue, save SP to FP
in prologue in order to get the correct stack backtrace.
However, ARM64 JIT used FP (x29) as eBPF fp register, FP is subjected to
change during function call so it may cause the BPF prog stack base address
change too.
Use x25 to replace FP as BPF stack base register (fp). Since x25 is callee
saved register, so it will keep intact during function call.
It is initialized in BPF prog prologue when BPF prog is started to run
everytime. Save and restore x25/x26 in BPF prologue and epilogue to keep
them intact for the outside of BPF. Actually, x26 is unnecessary, but SP
requires 16 bytes alignment.
So, the BPF stack layout looks like:
high
original A64_SP => 0:+-----+ BPF prologue
|FP/LR|
current A64_FP => -16:+-----+
| ... | callee saved registers
+-----+
| | x25/x26
BPF fp register => -80:+-----+
| |
| ... | BPF prog stack
| |
| |
current A64_SP => +-----+
| |
| ... | Function call stack
| |
+-----+
low
CC: Zi Shen Lim <zlim.lnx@gmail.com>
CC: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset pskb in macvlan_handle_frame in case skb_share_check returned a
clone.
Fixes: 8a4eb5734e ("net: introduce rx_handler results and logic around that")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipvlan_handle_frame is a rx_handler, and when it returns a value other
than RX_HANDLER_CONSUMED (here, NET_RX_DROP aka RX_HANDLER_ANOTHER),
__netif_receive_skb_core expects that the skb still exists and will
process it further, but we just freed it.
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a **skb to ipvlan_rcv_frame so that if skb_share_check returns a
new skb, we actually use it during further processing.
It's safe to ignore the new skb in the ipvlan_xmit_* functions, because
they call ipvlan_rcv_frame with local == true, so that dev_forward_skb
is called and always takes ownership of the skb.
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladislav Yasevich says:
====================
Fix issues with vlans without REORDER_HEADER
A while ago Phil Sutter brought up an issue with vlans without
REORDER_HEADER and bridges. The problem was that if a vlan
without REORDER_HEADER was a port in the bridge, the bridge ended
up forwarding corrupted packets that still contained the vlan header.
The same issue exists for bridge mode macvlan/macvtap devices.
An additional issue with vlans without REORDER_HEADER is that stacking
them also doesn't work. The reason here is that skb_reorder_vlan_header()
function assumes that it on ETH_HLEN bytes deep into the packet. That
is not the case, when you a vlan without REORRDER_HEADER flag set.
This series attempts to correct these 2 issues.
1) To solve the stacked vlans problem, the patch simply use
skb->mac_len as an offset to start copying mac addresses that
is part of header reordering.
2) To fix the issue with bridge/macvlan/macvtap, the second patch
simply doesn't write the vlan header back to the packet if the
vlan device is either a bridge or a macvlan port. This ends up
being the simplest and least performance intrussive solution.
I've considered extending patch 2 to all stacked devices (essentially
checked for the presense of rx_handler), but that feels like a broader
restriction and _may_ break existing uses.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vlan is configured with REORDER_HEADER set to 0, the vlan
header is put back into the packet and makes it appear that
the vlan header is still there even after it's been processed.
This posses a problem for bridge and macvlan ports. The packets
passed to those device may be forwarded and at the time of the
forward, vlan headers end up being unexpectedly present.
With the patch, we make sure that we do not put the vlan header
back (when REORDER_HEADER is 0) if a bridge or macvlan has
been configured on top of the vlan device.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have multiple stacked vlan devices all of which have
turned off REORDER_HEADER flag, the untag operation does not
locate the ethernet addresses correctly for nested vlans.
The reason is that in case of REORDER_HEADER flag being off,
the outer vlan headers are put back and the mac_len is adjusted
to account for the presense of the header. Then, the subsequent
untag operation, for the next level vlan, always use VLAN_ETH_HLEN
to locate the begining of the ethernet header and that ends up
being a multiple of 4 bytes short of the actuall beginning
of the mac header (the multiple depending on the how many vlan
encapsulations ethere are).
As a reslult, if there are multiple levles of vlan devices
with REODER_HEADER being off, the recevied packets end up
being dropped.
To solve this, we use skb->mac_len as the offset. The value
is always set on receive path and starts out as a ETH_HLEN.
The value is also updated when the vlan header manupations occur
so we know it will be correct.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default the driver allowed incorrect frames to be received. What is
worse the code does not handle very short frames correctly. The FCS
length is unconditionally subtracted, and the underflow can cause
skb_put to be called with large number after implicit cast to unsigned.
And indeed, an skb_over_panic() was observed with via-velocity.
This removes the module parameter as it does not work in it's
current state, and should be implemented via NETIF_F_RXALL if needed.
Suggested-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs fixes from Al Viro:
"A fs-cache regression fix, and adding a warning about obnoxiou^W
moderation of list given in MAINTAINERS"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
MAINTAINERS: linux-cachefs@redhat.com is moderated for non-subscribers
FS-Cache: Add missing initialization of ret in cachefiles_write_page()
Pull crypto fix from Herbert Xu:
"This fixes a bug in the qat driver where a user-space pointer is
dereferenced"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: qat - don't use userspace pointer
Following changes that appeared in lk 4.0.0, the gadget udc driver for
some ARM based Atmel SoCs (e.g. at91sam9x5 and sama5d3 families)
incorrectly deduced full-speed USB link speed even when the hardware
had negotiated a high-speed link. The fix is to make sure that the
UDPHS Interrupt Enable Register value does not mask the SPEED bit
in the Interrupt Status Register.
For a mass storage gadget this problem lead to failures when the host
had a USB 3 port with the xhci_hcd driver. If the host was a USB 2
port using the ehci_hcd driver then the mass storage gadget worked
(but probably at a lower speed than it should have).
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> #4.0+
Fixes: 9870d895ad ("usb: atmel_usba_udc: Mask status with enabled irqs")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change the permission of usb_dma parameter so it can
be used for runtime debug without reboot.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In some SoCs, dwc3 is implemented as a USB2.0 only
core, meaning that it can't ever achieve SuperSpeed.
Currect driver always sets gadget.max_speed to
USB_SPEED_SUPER unconditionally. This can causes
issues to some Host stacks where the host will issue
a GetBOS() request and we will reply with a BOS
containing Superspeed Capability Descriptor.
At least Windows seems to be upset by this fact and
prints a warning that we should connect $this device
to another port.
[ balbi@ti.com : rewrote entire commit, including
source code comment to make a lot clearer what the
problem is ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Ben McCauley <ben.mccauley@garmin.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here are a few changes in musb_h_tx_flush_fifo().
- It has been observed that sometimes (if not always) musb is unable
to flush tx fifo during urb dequeue when disconnect a device. But
it seems to be harmless, since the tx fifo flush is done again in
musb_ep_program() when re-use the hw_ep.
But the WARN() floods the console in the case when multiple tx urbs
are queued, so change it to dev_WARN_ONCE().
- applications could queue up many tx urbs, then the 1ms delay could
causes minutes of delay in device disconnect. So remove it to get
better user experience. The 1ms delay does not help the flushing
anyway.
- cleanup the debug code - related to lastcsr.
----
Note: The tx fifo flush issue has been observed during device disconnect
on AM335x.
To reproduce the issue, ensure tx urb(s) are queued when unplug the usb
device which is connected to AM335x usb host port.
I found using a usb-ethernet device and running iperf (client on AM335x)
has very high chance to trigger the problem.
Better to turn on dev_dbg() in musb_cleanup_urb() with CPPI enabled to
see the issue when aborting the tx channel.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In commit 734643dfbd ("usb: dwc2: host: add flag to reflect bus
state") we changed dwc2_port_suspend() not to set the lx_state
anymore (instead it sets the new bus_suspended variable). This
introduced a bug where we would fail to detect device insertions if:
1. Plug empty hub into dwc2
2. Plug USB flash drive into the empty hub.
3. Wait a few seconds
4. Unplug USB flash drive
5. Less than 2 seconds after step 4, plug the USB flash drive in again.
The dwc2_hcd_rem_wakeup() function should have been changed to look at
the new bus_suspended variable.
Let's fix it. Since commit b46146d59f ("usb: dwc2: host: resume root
hub on remote wakeup") talks about needing the root hub resumed if the
bus was suspended, we'll include it in our test.
It appears that the "port_l1_change" should only be set to 1 if we were
in DWC2_L1 (the driver currently never sets this), so we'll update the
former "else" case based on this test.
Fixes: 734643dfbd ("usb: dwc2: host: add flag to reflect bus state")
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Gregory Herrero <gregory.herrero@intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The comment for ahbcfg for rk3066 parameters (also used for rk3288)
claimed that ahbcfg was INCR16, but it wasn't. Since the bits weren't
shifted properly, the 0x7 ended up being masked and we ended up
programming 0x3 for the HBstLen. Let's set it to INCR16 properly.
As per Wu Liang Feng at Rockchip this may increase transmission
efficiency. I did blackbox tests with writing 0s to a USB-based SD
reader (forcefully capping CPU Freq to try to measure efficiency):
cd /sys/devices/system/cpu/cpu0/cpufreq
echo userspace > scaling_governor
echo 126000 > scaling_setspeed
for i in $(seq 10); do
dd if=/dev/zero of=/dev/sdb bs=1M count=750
done
With the above tests I found that speeds went from ~15MB/s to ~18MB/s.
Note that most other tests I did (including reading from the same USB
reader) didn't show any difference in performance.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Liangfeng Wu <wulf@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The function graph tracer adds instrumentation that is required to trace
both entry and exit of a function. In particular the function graph
tracer updates the "return address" of a function in order to insert
a trace callback on function exit.
Kernel power management functions like cpu_suspend() are called
upon power down entry with functions called "finishers" that are in turn
called to trigger the power down sequence but they may not return to the
kernel through the normal return path.
When the core resumes from low-power it returns to the cpu_suspend()
function through the cpu_resume path, which leaves the trace stack frame
set-up by the function tracer in an incosistent state upon return to the
kernel when tracing is enabled.
This patch fixes the issue by pausing/resuming the function graph
tracer on the thread executing cpu_suspend() (ie the function call that
subsequently triggers the "suspend finishers"), so that the function graph
tracer state is kept consistent across functions that enter power down
states and never return by effectively disabling graph tracer while they
are executing.
Fixes: 819e50e25d ("arm64: Add ftrace support")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We try to convert the old way of of specifying fb tiling (obj->tiling)
into the new fb modifiers. We store the result in the passed in mode_cmd
structure. But that structure comes directly from the addfb2 ioctl, and
gets copied back out to userspace, which means we're clobbering the
modifiers that the user provided (all 0 since the DRM_MODE_FB_MODIFIERS
flag wasn't even set by the user). Hence if the user reuses the struct
for another addfb2, the ioctl will be rejected since it's now asking for
some modifiers w/o the flag set.
Fix the problem by making a copy of the user provided structure. We can
play any games we want with the copy.
IGT-Version: 1.12-git (x86_64) (Linux: 4.4.0-rc1-stereo+ x86_64)
...
Subtest basic-X-tiled: SUCCESS (0.001s)
Test assertion failure function pitch_tests, file kms_addfb_basic.c:167:
Failed assertion: drmIoctl(fd, DRM_IOCTL_MODE_ADDFB2, &f) == 0
Last errno: 22, Invalid argument
Stack trace:
#0 [__igt_fail_assert+0x101]
#1 [pitch_tests+0x619]
#2 [__real_main426+0x2f]
#3 [main+0x23]
#4 [__libc_start_main+0xf0]
#5 [_start+0x29]
#6 [<unknown>+0x29]
Subtest framebuffer-vs-set-tiling failed.
**** DEBUG ****
Test assertion failure function pitch_tests, file kms_addfb_basic.c:167:
Failed assertion: drmIoctl(fd, DRM_IOCTL_MODE_ADDFB2, &f) == 0
Last errno: 22, Invalid argument
**** END ****
Subtest framebuffer-vs-set-tiling: FAIL (0.003s)
...
IGT-Version: 1.12-git (x86_64) (Linux: 4.4.0-rc1-stereo+ x86_64)
Subtest framebuffer-vs-set-tiling: SUCCESS (0.000s)
Cc: stable@vger.kernel.org # v4.1+
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 2a80eada32 ("drm/i915: Add fb format modifier support")
Testcase: igt/kms_addfb_basic/clobbered-modifier
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447261890-3960-1-git-send-email-ville.syrjala@linux.intel.com
Properly double the hdisplay/vdisplay timings that we use as the primary
plane size with stereo doubled modes. Otherwise the modeset gets
rejected on machines where the primary plane must be fullscreen, and on
the rest only the first eye would get a visible plane.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org #v3.19+
Fixes: 042652ed95 ("drm/atomic-helper: implementatations for legacy interfaces")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447686157-29607-1-git-send-email-ville.syrjala@linux.intel.com
Testcase: igt/kms_3d
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When using EOImode==1, we may mark interrupts as being forwarded
to a virtual machine. In that case, the interrupt is left active
while being passed to the VM.
If we suspend the system before the VM has deactivated the interrupt,
the active state will be lost (which may be very annoying, as this
may result in spurious interrupts and a confused guest).
To avoid this, save and restore the active state together with the
rest of the GIC registers.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1447701208-18150-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When restoring the GIC state (after a suspend/resume cycle,
for example), the driver directly writes the 'enabled' state
it has saved by accessing GICD_ISENABLERn, which performs
an OR operation between the value present in the register
and the value we write.
If whatever code that has run before we reentered the kernel
has enabled an interrupt that was previously disabled, we won't
restore that disabled state.
Making sure we first clear the register (by writting to
GICD_ICENABLERn) before restoring the enabled state.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1447701208-18150-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When booting a GIC/GICv3 based system, we have no idea what
state the firmware (or previous kernel in the case of kexec)
has left the GIC, and some interrupts may still be active.
In order to garantee that we have a clean state, make sure
the active bits are cleared at init time.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1447701208-18150-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
including ptrace.h brings a definition of BITS_PER_PAGE into device
drivers and cause a build warning in allmodconfig builds:
drivers/block/drbd/drbd_bitmap.c:482:0: warning: "BITS_PER_PAGE" redefined
#define BITS_PER_PAGE (1UL << (PAGE_SHIFT + 3))
This uses a slightly different way to express current_pt_regs()
that avoids the use of the header and gets away with the already
included asm/ptrace.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Including linux/acpi.h from asm/dma-mapping.h causes tons of compile-time
warnings, e.g.
drivers/isdn/mISDN/dsp_ecdis.h:43:0: warning: "FALSE" redefined
drivers/isdn/mISDN/dsp_ecdis.h:44:0: warning: "TRUE" redefined
drivers/net/fddi/skfp/h/targetos.h:62:0: warning: "TRUE" redefined
drivers/net/fddi/skfp/h/targetos.h:63:0: warning: "FALSE" redefined
However, it looks like the dependency should not even there as
I do not see why __generic_dma_ops() cares about whether we have
an ACPI based system or not.
The current behavior is to fall back to the global dma_ops when
a device has not set its own dma_ops, but only for DT based systems.
This seems dangerous, as a random device might have different
requirements regarding IOMMU or coherency, so we should really
never have that fallback and just forbid DMA when we have not
initialized DMA for a device.
This removes the global dma_ops variable and the special-casing
for ACPI, and just returns the dma ops that got set for the
device, or the dummy_dma_ops if none were present.
The original code has apparently been copied from arm32 where we
rely on it for ISA devices things like the floppy controller, but
we should have no such devices on ARM64.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[catalin.marinas@arm.com: removed acpi_disabled check in arch_setup_dma_ops()]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When booting a 64k pages kernel that is built with CONFIG_DEBUG_RODATA
and resides at an offset that is not a multiple of 512 MB, the rounding
that occurs in __map_memblock() and fixup_executable() results in
incorrect regions being mapped.
The following snippet from /sys/kernel/debug/kernel_page_tables shows
how, when the kernel is loaded 2 MB above the base of DRAM at 0x40000000,
the first 2 MB of memory (which may be inaccessible from non-secure EL1
or just reserved by the firmware) is inadvertently mapped into the end of
the module region.
---[ Modules start ]---
0xfffffdffffe00000-0xfffffe0000000000 2M RW NX ... UXN MEM/NORMAL
---[ Modules end ]---
---[ Kernel Mapping ]---
0xfffffe0000000000-0xfffffe0000090000 576K RW NX ... UXN MEM/NORMAL
0xfffffe0000090000-0xfffffe0000200000 1472K ro x ... UXN MEM/NORMAL
0xfffffe0000200000-0xfffffe0000800000 6M ro x ... UXN MEM/NORMAL
0xfffffe0000800000-0xfffffe0000810000 64K ro x ... UXN MEM/NORMAL
0xfffffe0000810000-0xfffffe0000a00000 1984K RW NX ... UXN MEM/NORMAL
0xfffffe0000a00000-0xfffffe00ffe00000 4084M RW NX ... UXN MEM/NORMAL
The same issue is likely to occur on 16k pages kernels whose load
address is not a multiple of 32 MB (i.e., SECTION_SIZE). So round to
SWAPPER_BLOCK_SIZE instead of SECTION_SIZE.
Fixes: da141706ae ("arm64: add better page protections to arm64")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
plane_mask should be cleared inside the retry loop, because it gets
reset on every retry. Without this fix the plane->fb refcounting might
get out of sync on retries, resulting in either leaked memory or
use-after-free.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: stable@vger.kernel.org #v4.3
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447237751-9663-3-git-send-email-maarten.lankhorst@ubuntu.com
legacy_cursor_update was being set in restore_fbdev_mode_atomic which was
probably unintended. Fix this by only setting it in the function that needs it.
This oversight was introduced in
commit bbb1e52402
Author: Rob Clark <robdclark@gmail.com>
Date: Tue Aug 25 15:35:58 2015 -0400
drm/fb-helper: atomic restore_fbdev_mode()...
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: checkpatch fix]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447237751-9663-2-git-send-email-maarten.lankhorst@ubuntu.com
While dax pmd mappings are functional in the nominal path they trigger
kernel crashes in the following paths:
BUG: unable to handle kernel paging request at ffffea0004098000
IP: [<ffffffff812362f7>] follow_trans_huge_pmd+0x117/0x3b0
[..]
Call Trace:
[<ffffffff811f6573>] follow_page_mask+0x2d3/0x380
[<ffffffff811f6708>] __get_user_pages+0xe8/0x6f0
[<ffffffff811f7045>] get_user_pages_unlocked+0x165/0x1e0
[<ffffffff8106f5b1>] get_user_pages_fast+0xa1/0x1b0
kernel BUG at arch/x86/mm/gup.c:131!
[..]
Call Trace:
[<ffffffff8106f34c>] gup_pud_range+0x1bc/0x220
[<ffffffff8106f634>] get_user_pages_fast+0x124/0x1b0
BUG: unable to handle kernel paging request at ffffea0004088000
IP: [<ffffffff81235f49>] copy_huge_pmd+0x159/0x350
[..]
Call Trace:
[<ffffffff811fad3c>] copy_page_range+0x34c/0x9f0
[<ffffffff810a0daf>] copy_process+0x1b7f/0x1e10
[<ffffffff810a11c1>] _do_fork+0x91/0x590
All of these paths are interpreting a dax pmd mapping as a transparent
huge page and making the assumption that the pfn is covered by the
memmap, i.e. that the pfn has an associated struct page. PTE mappings
do not suffer the same fate since they have the _PAGE_SPECIAL flag to
cause the gup path to fault. We can do something similar for the PMD
path, or otherwise defer pmd support for cases where a struct page is
available. For now, 4.4-rc and -stable need to disable dax pmd support
by default.
For development the "depends on BROKEN" line can be removed from
CONFIG_FS_DAX_PMD.
Cc: <stable@vger.kernel.org>
Cc: Jan Kara <jack@suse.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
fs/cachefiles/rdwr.c: In function ‘cachefiles_write_page’:
fs/cachefiles/rdwr.c:882: warning: ‘ret’ may be used uninitialized in
this function
If the jump to label "error" is taken, "ret" will indeed be
uninitialized, and random stack data may be printed by the debug code.
Fixes: 102f4d900c ("FS-Cache: Handle a write to the page immediately beyond the EOF marker")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The Broadcom NAND driver is used by many different groups at Broadcom
now, so use the same mailing-list we use for other areas of the kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Given that INTUOSHT < BAMBOO_PT
features->type >= INTUOSHT || features->type <= BAMBOO_PT
condition is always true, and therefore device_type is under certain
circumstances wrongly set with WACOM_DEVICETYPE_PAD bit set.
Fix the condition so that it actually represents the range as intended.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The acpi_ec_delete_query() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 3349fb64b2 (ACPI / SBS: Add 5 us delay to fix SBS
hangs on MacBook), since the delay introduced by it is not necessary
any more after commit add68d6aa9 (ACPI / SMBus: Fix boot stalls /
high CPU caused by reentrant code).
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the SBS initialisation, a reentrant call to wait_event_timeout()
causes an intermittent boot stall of several minutes usually following
the "Switching to clocksource tsc" message. Another symptom of this bug
is high CPU usage from programs (Firefox, upowerd) querying the battery
state. This is caused by:
1. drivers/acpi/sbshc.c wait_transaction_complete() calls
wait_event_timeout():
if (wait_event_timeout(hc->wait, smb_check_done(hc),
msecs_to_jiffies(timeout)))
2. ___wait_event sets task state to uninterruptible
3. ___wait_event calls the "condition" smb_check_done()
4. smb_check_done (sbshc.c) calls through to ec_read() in
drivers/acpi/ec.c
5. ec_guard() is reached which calls wait_event_timeout()
if (wait_event_timeout(ec->wait,
ec_transaction_completed(ec),
guard))
ie. wait_event_timeout() is being called again inside evaluation of
the previous wait_event_timeout() condition
5. The EC IRQ handler calls wake_up() and wakes up the sleeping task in
ec_guard()
6. The task is now in state running even though the wait "condition" is
still being evaluated
7. The "condition" check returns false so ___wait_event calls
schedule_timeout()
8. Since the task state is running, the scheduler immediately schedules
it again
9. This loop usually repeats for around 250 seconds even though the
original wait_event_timeout was only 1000ms.
The timeout is incorrect because each call to schedule_timeout()
usually returns immediately, taking less than 1ms, so the jiffies
timeout counter is not decremented. The task is now stuck in a
running state, and so is highly likely to be immediately
rescheduled, which takes less than a jiffy. The loop will never exit
if all schedule_timeout() calls take less than a jiffy.
Fix this by replacing SMBus reads in the wait_event_timeout condition
with checks of a boolean value that is updated by the EC query handler.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=107191
Link: https://lkml.org/lkml/2015/11/6/776
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that IP1000A chips are supported by dl2k driver, the buggy ipg
driver can be removed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.
This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.
Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
vendor=0x13f0 device=0x1023 (rev 0x41)
subsystem vendor=0x1043 device=0x8180
MAC address registers access needed to be changed from 8-bit to 16-bit
because 8-bit does not work on IP1000A. 8-bit access is not even
allowed in the TC9020 datasheet (although it worked). 16-bit access
works on both.
Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
a rebranded TC9020):
vendor=0x1186 device=0x4000 (rev 0x0c)
subsystem vendor=0x1186 device=0x4000
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that IRQ number passed to dev_pm_set_wake_irq() and
dev_pm_set_dedicated_wake_irq() is valid (not negative) before
accepting it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
