This includes following USB4/Thunderbolt changes for the v6.9 merge
window:
- Reset the topology also for USB4 v1 routers on driver load
- DisplayPort tunneling and bandwidth allocation mode improvements
- Tracepoint support for the control channel
- Couple of minor fixes and cleanups.
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=9hHe
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.9 merge window
This includes following USB4/Thunderbolt changes for the v6.9 merge
window:
- Reset the topology also for USB4 v1 routers on driver load
- DisplayPort tunneling and bandwidth allocation mode improvements
- Tracepoint support for the control channel
- Couple of minor fixes and cleanups.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (23 commits)
thunderbolt: Constify the struct device_type usage
thunderbolt: Add trace events support for the control channel
thunderbolt: Keep the domain powered when USB4 port is in redrive mode
thunderbolt: Improve DisplayPort tunnel setup process to be more robust
thunderbolt: Calculate DisplayPort tunnel bandwidth after DPRX capabilities read
thunderbolt: Reserve released DisplayPort bandwidth for a group for 10 seconds
thunderbolt: Introduce tb_tunnel_direction_downstream()
thunderbolt: Re-order bandwidth group functions
thunderbolt: Fail the failed bandwidth request properly
thunderbolt: Log an error if DPTX request is not cleared
thunderbolt: Handle bandwidth allocation mode disable request
thunderbolt: Re-calculate estimated bandwidth when allocation mode is enabled
thunderbolt: Use DP_LOCAL_CAP for maximum bandwidth calculation
thunderbolt: Correct typo in host_reset parameter
thunderbolt: Skip discovery also in USB4 v2 host
thunderbolt: Reset only non-USB4 host routers in resume
thunderbolt: Remove usage of the deprecated ida_simple_xx() API
thunderbolt: Fix rollback in tb_port_lane_bonding_enable() for lane 1
thunderbolt: Fix XDomain rx_lanes_show and tx_lanes_show
thunderbolt: Reset topology created by the boot firmware
...
The bit 23, CM TBT3 Not Supported (CNS), in ROUTER_CS_5 indicates
whether a USB4 Connection Manager is TBT3-Compatible and should be:
0b for TBT3-Compatible
1b for Not TBT3-Compatible
Fixes: b04079837b ("thunderbolt: Add initial support for USB4")
Cc: stable@vger.kernel.org
Signed-off-by: Mohammad Rahimi <rahimi.mhmmd@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently tb_switch_reset() only did something for Thunderbolt 1
devices. Expand this to support all generations, including USB4, and
both host and device routers.
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Introduce a function that issues Downstream Port Reset to a USB4 port.
This supports Thunderbolt 2, 3 and USB4 routers.
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 v2 spec defines a Gen 4 link that can operate as an aggregated
symmetric (80/80G) or asymmetric (120/40G). When the link is asymmetric,
the USB4 port on one side of the link operates with three TX lanes and
one RX lane, while the USB4 port on the opposite side of the link
operates with three RX lanes and one TX lane.
Add support for the asymmetric link and provide functions that can be
used to transition the link to asymmetric and back.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 v2 spec allows USB4 links that are part of a pass through tunnel
(such as DisplayPort and USB 3.x Gen T) to enter lower CL states, which
provide better power management. For this USB4 v2 routers in their path
config space of lane 0 adapter include a new bit PMPS (PM packet
support) that needs to be set.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fix typo of HPD bit stands for Hot Plug Detect.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It turns out there is no need to use the actual link rate when
reclaiming bandwidth for USB 3.x. The reason is that we use consumed
bandwidth which is coming from xHCI when releasing bandwidth (for
example for DisplayPort tunneling) and this can be anything between
1000 Mb/s to maximum, so when reclaiming we can just bump it up back to
maximum instead of actual link rate (which is always <= maximum).
This allows us to get rid of couple of unnecessary lines of code.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This adds support for the UHBR (Ultra High Bit Rate) bandwidths
introduced with DisplayPort 2.0 (and refined in 2.1). These can go up to
80 Gbit/s and their support is represent in additional bits in the DP IN
capability.
This updates the DisplayPort tunneling to support these new rates too.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is new TMU mode introduced with the USB4 v2. This mode is simpler
than the existing ones and allows all CL states as well. Enable this for
all links where both side routers are v2 and keep the existing
functionality for the v1 and earlier links.
Currently only support the MedRes rate. We can add the HiFi rate later
too if it turns out to be useful.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 v2 spec introduces modified encapsulation of PCIe TLP and DLLP
packets. This improves the PCIe tunneled traffic usage by reducing
overhead. Enable this if both sides of the link support it.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Program the CMUV (Connection Manager USB4 Version) field for USB4 v2 and
v1 routers according to the spec.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 v2 bumps the per-lane speed up to 40 Gb/s. Also the lanes are
always bonded which gives 80 Gb/s symmetric link (and 120/40 Gb/s
asymmetric). This updates the speed and width of routers and XDomain
connections to support the Gen 4 link. For now we keep the link as is
even if it is already asymmetric.
While there make tb_port_set_link_width() static.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add a new function usb4_switch_version() that can be used to figure out
the spec version of the router and make tb_switch_is_usb4() to use it as
well. Update the uevent accordingly.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec defines an additional feature that DP IN adapters can
implement (alongside with the graphics DPCD register set) to support
more dynamic bandwidth management for DisplayPort tunnels. For the
connection manager the communication happens through the DP IN adapter
using a set of registers in the adapter config space allocated for this.
Add functions that export this functionality for the rest of the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If CL states are enabled for the link it may be in these states too when
reading the lane adapter state but it will enter CL0 as soon as there is
traffic in the high-speed lanes. Upon discovery we want to make sure
that is accounted as the link being up, otherwise we end up tearing down
the topology with no good reason.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Wake on connect/disconnect is only supported while runtime suspend for
now, which is obviously necessary. It is also not inherently desired for
the system to wakeup on Thunderbolt/USB4 hot plug events. However, we
can still make user in control of waking up the system in the events of
hot plug/unplug.
This patch adds 'wakeup' attribute under 'usb4_portX/power' sysfs
attribute and only enables wakes on connect/disconnect to the respective
port when 'wakeup' is set to 'enabled'. The attribute is set to
'disabled' by default.
Signed-off-by: Rajat Khandelwal <rajat.khandelwal@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Software that has run before the USB4 CM in Linux runs may have disabled
hotplug events for a given lane adapter.
Other CMs such as that one distributed with Windows 11 will enable hotplug
events. Do the same thing in the Linux CM which fixes hotplug events on
"AMD Pink Sardine".
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Instead of testing just a single CL state we can pass a bitmask of
states to check. This makes it simpler for callers of the function.
We also add a check for CL2 even though not fully supported by the
driver yet.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In this patch we add support for a second low power state of the link: CL1.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle.
We enable it, if both sides of the link support it,
and only for the first hop router (i.e. the first device that connected
to the host router). This is needed for better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 Inter-Domain Service specification defines a protocol that can
be used to establish lane bonding between two USB4 domains (hosts). So
far we have not implemented it because the host controller DMA was not
fast enough to be able to go over 20 Gbits/s even if lanes were bonded.
However, starting from Intel Alder Lake CPUs the DMA can go over
20 Gbits/s so now it makes more sense to add this support to the driver.
Because both ends need to negotiate the bonding we add a simple state
machine that tracks the connection state and does the necessary steps
described by the USB4 Inter-Domain Service specification. We only
establish lane bonding when both sides of the link support it. Otherwise
we default to use the single lane. Also this is only done when software
connection manager is used. On systems with firmware based connection
manager, it handles the high-speed tunneling so bonding lanes is
specific to the implementation (Intel firmware based connection manager
does not support lane bonding).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The structure `tb_eeprom_ctl` is used to show the bits accessed when
reading/writing EEPROM.
As this structure is specified in the USB4 spec as `VSC_CS_4` update
the names and use of members to match the specification. This should not
change anything functionally.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 1.0 specification outlines the `cap_plug_events` structure as
`VSC_CS_1`. This shows that 4 bits of `VSC_CS_1` are TBT3 compatible in
USB4, but TBT3 controllers also support disabling XHCI.
Update the names and comments to more closely match the specification.
This should not change anything functionally.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Both Alpine Ridge and Titan Ridge require special flows in order to
activate the internal xHCI controller when there is USB device connected
to the downstream type-C port. This implements the missing flows for
both.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Titan Ridge does not disable AUX timers when it gets SET_CONFIG
with SET_LTTPR_MODE set which makes DP tunneling to fail. For this
reason disable LTTPR on Titan Ridge device side.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Low power link states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle. The
simplest one being called CL0s. Follow what we already do for USB4
device routers and enable CL0s for Intel Titan Ridge device router too.
This allows better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Rename the VSC capability: TB_VSE_CAP_IECS to TB_VSE_CAP_CP_LP to follow
the Intel devices namings as appear in the datasheet. This capability
is used for controlling CLx (Low Power states of the link).
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Titan Ridge based routers have slightly different flow for time
disruption than USB4 compliant routers. This makes it work on Titan
Ridge too. Needed to enable link low power states on Titan Ridge.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In this patch we add enabling of CL0s - a low power state of the link.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle. For now,
we add support only for first low power state: CL0s. We enable it, if
both sides of the link support it, and only for the first hop router.
(i.e. the first device that connected to the host router). This is
needed for better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Up until Titan Ridge (Thunderbolt 3) device routers only supported
bi-directional mode. In this patch we add to TMU a uni-directional mode.
The uni-directional mode is needed for enabling of low power state of
the link (CLx).
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 routers must expose their preferred credit (buffer) allocation
information through router operation. This information tells the
connection manager how the router prefers its buffers to be allocated to
get the expected bandwidth for the supported protocols.
Read this information and store it as part of struct tb_switch for each
USB4 router.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Latest USB4 spec added a new wake bit for DisplayPort so add this to the
driver when runtime suspending. This way wake up the domain when a new
monitor is plugged in to any of the device routers.
Also do the same for pre-USB4 devices through the link controller
registers as documented in chapter 13 of the USB4 spec.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec says that for TBT3 compatible device routers the connection
manager needs to set SLI (Start Lane Initialization) to get the lanes
that were not connected back to functional state after sleep. Same needs
to be done if the link was XDomain.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
We are going to use these in subsequent patch so make them available
outside of usb4.c.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The currect code expects that the router returns back the status of the
NVM authentication immediately. When tested against a real USB4 device
what happens is that the router is reset and only after that the result
is updated in the ROUTER_CS_26 register status field. This also seems to
align better what the spec suggests.
For this reason do the same what we already do with the Thunderbolt 3
devices and perform the NVM upgrade in two phases. First start the
NVM_AUTH router operation and once the router is added back after the
reset read the status in ROUTER_CS_26 and expose it to the userspace
accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This adds debugfs interface that can be used for debugging possible
issues in hardware/software. It exposes router and adapter config spaces
through files like this:
/sys/kernel/debug/thunderbolt/<DEVICE>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/path
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT1>/counters
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/regs
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/path
/sys/kernel/debug/thunderbolt/<DEVICE>/<PORT2>/counters
...
The "regs" is either the router or port configuration space register
dump. The "path" is the port path configuration space and "counters" is
the optional counters configuration space.
These files contains one register per line so it should be easy to use
normal filtering tools to find the registers of interest if needed.
The router and adapter regs file becomes writable when
CONFIG_USB4_DEBUGFS_WRITE is enabled (which is not supposed to be done
in production systems) and in this case the developer can write "offset
value" lines there to modify the hardware directly. For convenience this
also supports the long format the read side produces (but ignores the
additional fields). The counters file can be written even when
CONFIG_USB4_DEBUGFS_WRITE is not enabled and it is only used to clear
the counter values.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure will be needed by the debugfs implementation so make it
available outside of cap.c.
While there add kernel-doc comments to the structure.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for the router and the whole domain to wake up from system
suspend states we need to enable wakes for the connected routers. For
device routers we enable wakes from PCIe and USB 3.x. This allows
devices such as keyboards connected to USB 3.x hub that is tunneled to
wake the system up as expected. For all routers we enabled wake on USB4
for each connected ports. This is used to propagate the wake from router
to another.
Do the same for legacy routers through link controller vendor specific
registers as documented in USB4 spec chapter 13.
While there correct kernel-doc of usb4_switch_set_sleep() -- it does not
enable wakes instead there is a separate function (usb4_switch_set_wake())
that does.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec mandates that the lane 1 should be disabled if lanes are not
bonded. For host-to-host connections (XDomain) we don't support lane
bonding so in order to be compatible with the spec, disable lane 1 when
another host is connected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When the port is connected to another host it should be marked as such
in the USB4 port capability. This information is used by the router
during sleep and wakeup.
Also do the same for legacy switches via link controller vendor specific
registers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Some external devices can support completing thunderbolt authentication
when they are unplugged. For this to work though, the link controller must
remain operational.
The only device known to support this right now is the Dell WD19TB, so add
a quirk for this.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec specifies standard set of sideband operations that are send
over the low speed link to access either retimers on the link or the
link parter (the other router). The USB4 retimer spec extends these and
adds operations for retimer NVM upgrade.
This implements the retimer access and NVM upgrade USB4 port sideband
operations which we need for retimer support in the patch that follows.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Each host router USB3 downstream adapter has a set of registers that are
used to negotiate bandwidth between the connection manager and the
internal xHCI controller. These registers allow dynamic bandwidth
management for USB3 isochronous traffic based on what is actually
consumed vs. allocated at any given time.
Implement these USB3 bandwidth negotiation routines to allow the
software connection manager take advantage of these.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB3 tunneling is possible only over USB4 link so don't create USB3
tunnels if that's not the case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 added a capability to tunnel USB 3.x protocol over the USB4
fabric. USB4 device routers may include integrated SuperSpeed HUB or a
function or both. USB tunneling follows PCIe so that the tunnel is
created between the parent and the child router from USB3 downstream
adapter port to USB3 upstream adapter port over a single USB4 link.
This adds support for USB 3.x tunneling and also capability to discover
existing USB 3.x tunnels (for example created by connection manager in
boot firmware).
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-9-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Time Management Unit (TMU) is included in each USB4 router. It is used
to synchronize time across the USB4 fabric. By default when USB4 router
is plugged to the domain, its TMU is turned off. This differs from
Thunderbolt (1, 2 and 3) devices whose TMU is by default configured to
bi-directional HiFi mode. Since time synchronization is needed for
proper Display Port tunneling this means we need to configure the TMU on
USB4 compliant devices.
The USB4 spec allows some flexibility on how the TMU can be configured.
This makes it possible to enable link power management states (CLx) in
certain topologies, where for example DP tunneling is not used. TMU can
also be re-configured dynamicaly depending on types of tunnels created
over the USB4 fabric.
In this patch we simply configure the TMU to be in bi-directional HiFi
mode. This way we can tunnel any kind of traffic without need to perform
complex steps to re-configure the domain dynamically. We can add more
fine-grained TMU configuration later on when we start enabling CLx
states.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-8-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 is the public specification based on Thunderbolt 3 protocol. There
are some differences in register layouts and flows. In addition to PCIe
and DP tunneling, USB4 supports tunneling of USB 3.x. USB4 is also
backward compatible with Thunderbolt 3 (and older generations but the
spec only talks about 3rd generation). USB4 compliant devices can be
identified by checking USB4 version field in router configuration space.
This patch adds initial support for USB4 compliant hosts and devices
which enables following features provided by the existing functionality
in the driver:
- PCIe tunneling
- Display Port tunneling
- Host and device NVM firmware upgrade
- P2P networking
This brings the USB4 support to the same level that we already have for
Thunderbolt 1, 2 and 3 devices.
Note the spec talks about host and device "routers" but in the driver we
still use term "switch" in most places. Both can be used interchangeably.
Co-developed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-5-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Titan Ridge supports Display Port 1.4 which adds HBR3 (High Bit Rate)
rates that may be up to 8.1 Gb/s over 4 lanes. This translates to
effective data bandwidth of 25.92 Gb/s (as 8/10 encoding is removed by
the DP adapters when going over Thunderbolt fabric). If another high
rate monitor is connected we may need to reduce the bandwidth it
consumes so that it fits into the total 40 Gb/s available on the
Thunderbolt fabric.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
To perform proper Display Port tunneling for Thunderbolt 3 devices we
need to allocate DP resources for DP IN port before they can be used.
The reason for this is that the user can also connect a monitor directly
to the Type-C ports in which case the Thunderbolt controller acts as
re-driver for Display Port (no tunneling takes place) taking the DP
sinks away from the connection manager. This allocation is done using
special sink allocation registers available through the link controller.
We can pair DP IN to DP OUT only if
* DP IN has sink allocated via link controller
* DP OUT port receives hotplug event
For DP IN adapters (only for the host router) we first query whether
there is DP resource available (it may be the previous instance of the
driver for example already allocated it) and if it is we add it to the
list. We then update the list when after each plug/unplug event to a DP
IN/OUT adapter. Each time the list is updated we try to find additional
DP IN <-> DP OUT pairs for tunnel establishment. This strategy also
makes it possible to establish another tunnel in case there are 3
monitors connected and one gets unplugged releasing the DP IN adapter
for the new tunnel.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
