Fix the following compilation warning using W=1 build:
arm-linux-gnueabi-ld: drivers/spi/spi-stm32-qspi.o: in function `stm32_qspi_poll_status':
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210604075009.25914-1-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI_ALTERA_CORE config symbol controls compilation of the Altera SPI
Controller core code. It is already selected by all of its users, so
there is no reason to make it visible, unless compile-testing.
Fixes: b0c3d9354d ("spi: altera: separate core code from platform code")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/f0cb8e66baba4506db6f42fca74dc51b76883507.1619534253.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a Device Feature List (DFL) bus driver for the
Altera SPI Master controller. The SPI master is connected to an
Intel SPI Slave to Avalon Bridge inside an Intel MAX10
BMC Chip.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Link: https://lore.kernel.org/r/20210416165720.554144-3-matthew.gerlach@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver supports SPI Controller for HiSilicon Kunpeng SoCs. This
driver supports SPI operations using FIFO mode of transfer.
DMA is not supported, and we just use IRQ mode for operation completion
notification.
Only ACPI firmware is supported.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1616836200-45827-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The main focus of this release from a framework point of view has been
spi-mem where we've acquired support for a few new hardware features
which enable better performance on suitable hardware. Otherwise mostly
thanks to Arnd's cleanup efforts on old platforms we've removed several
obsolete drivers which just about balance out the newer drivers we've
added this cycle.
- Allow drivers to flag if they are unidirectional.
- Support for DTR mode and hardware acceleration of dummy cycles in spi-mem.
- Support for Allwinder H616, Intel Lightning Mountain, nVidia Tegra
QuadSPI, Realtek RTL838x and RTL839x.
- Removal of obsolute EFM32, Txx9 and SIRF Prima and Atlas drivers.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmAq3M0ACgkQJNaLcl1U
h9Aq3gf6AuboDwFguKZAmXp27zjYsv5o5KtPyycTltIIfjGuA58+fN2zQT+puoGI
wzafjk9R73Foa67YKUwClaBGZNZbYOkB2iOk9a+/sku6k3jO14moybpMuL32dCVe
lutKd9D4n8/J5UHX3SHKHAZ9r2vp28rlaZa4wd79Ww5r+BLajUcrkjtr4GVT5k1k
WzzC0nUjE/zg1oV+PlakMolwK+iBCQYTT7S4r/OQAABQIkXXdtwmGvFUUXpGVF19
GUs52XI8QzK5504Xl+F7NF1+2zHovO11PTHnd+rAe6AfA/NGggtk6O1Y9R4tQHF9
TN6PHukNxUdTFfe6RTbSzPagpFydvQ==
=/4Ve
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The main focus of this release from a framework point of view has been
spi-mem where we've acquired support for a few new hardware features
which enable better performance on suitable hardware.
Otherwise mostly thanks to Arnd's cleanup efforts on old platforms
we've removed several obsolete drivers which just about balance out
the newer drivers we've added this cycle.
Summary:
- Allow drivers to flag if they are unidirectional.
- Support for DTR mode and hardware acceleration of dummy cycles in
spi-mem.
- Support for Allwinder H616, Intel Lightning Mountain, nVidia Tegra
QuadSPI, Realtek RTL838x and RTL839x.
- Removal of obsolete EFM32, Txx9 and SIRF Prima and Atlas drivers"
* tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (76 commits)
spi: Skip zero-length transfers in spi_transfer_one_message()
spi: dw: Avoid stack content exposure
spi: cadence-quadspi: Use spi_mem_dtr_supports_op()
spi: spi-mem: add spi_mem_dtr_supports_op()
spi: atmel-quadspi: Disable the QSPI IP at suspend()
spi: pxa2xx: Add IDs for the controllers found on Intel Lynxpoint
spi: pxa2xx: Fix the controller numbering for Wildcat Point
spi: Change provied to provided in the file spi.h
spi: mediatek: add set_cs_timing support
spi: support CS timing for HW & SW mode
spi: add power control when set_cs_timing
spi: stm32: make spurious and overrun interrupts visible
spi: stm32h7: replace private SPI_1HZ_NS with NSEC_PER_SEC
spi: stm32: defer probe for reset
spi: stm32: driver uses reset controller only at init
spi: stm32h7: ensure message are smaller than max size
spi: stm32: use bitfield macros
spi: stm32: do not mandate cs_gpio
spi: stm32: properly handle 0 byte transfer
spi: clps711xx: remove redundant white-space
...
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120161658.3820610-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The Ericsson U300 platform was one of two ARM929 based SoC platforms for
mobile phones in ST-Ericsson after the merger of Ericsson with ST-NXP
into ST-Ericsson, the other one being the ST Nomadik.
The platform was not widely adopted in Linux based systems and was
replaced with the far superior ST-Ericsson U8500 in 2011, but Linus
Walleij kept maintaining the code for the whole time.
Linus continues to use the Nomadik machine, but decided to drop
u300 from the kernel as part of this year's spring cleaning.
Thanks for having maintained it all these years.
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/lkml/CACRpkdbJkiHR9FSfJTH_5d_qRU1__dRXHM1TL40iqNRKbGQfrQ@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SPI driver for the Renesas RPC-IF is present on the RZ/G2
Series. Add that to the description.
Suggested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210102115412.3402059-3-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I mistakenly added the select attributes to the SPI_DW_BT1_DIRMAP config
instead of having them defined in SPI_DW_BT1. If the kernel doesn't have
the MULTIPLEXER and MUX_MMIO configs manually enabled and the
SPI_DW_BT1_DIRMAP config hasn't been selected, Baikal-T1 SPI device will
always fail to be probed by the driver. Fix that and the error reported by
the test robot:
>> ld.lld: error: undefined symbol: devm_mux_control_get
>>> referenced by spi-dw-bt1.c
>>> spi/spi-dw-bt1.o:(dw_spi_bt1_sys_init) in archive drivers/built-in.a
by moving the MULTIPLEXER/MUX_MMIO configs selection to the SPI_DW_BT1
config.
Link: https://lore.kernel.org/lkml/202011161745.uYRlekse-lkp@intel.com/
Link: https://lore.kernel.org/linux-spi/20201116040721.8001-1-rdunlap@infradead.org/
Fixes: abf0090753 ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201127144612.4204-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
Baikal-T1 is equipped with three DW APB SSI-based MMIO SPI controllers.
Two of them are pretty much normal: with IRQ, DMA, FIFOs of 64 words
depth, 4x CSs, but the third one as being a part of the Baikal-T1 System
Boot Controller has got a very limited resources: no IRQ, no DMA, only a
single native chip-select and Tx/Rx FIFO with just 8 words depth
available. In order to provide a transparent initial boot code execution
the Boot SPI controller is also utilized by an vendor-specific IP-block,
which exposes an SPI flash direct mapping interface. Since both direct
mapping and SPI controller normal utilization are mutual exclusive only
one of these interfaces can be used to access an external SPI slave
device. That's why a dedicated mux is embedded into the System Boot
Controller. All of that is taken into account in the Baikal-T1-specific DW
APB SSI glue driver implemented by means of the DW SPI core module.
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-22-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Aside from the synchronous Tx-Rx mode, which has been utilized to create
the normal SPI transfers in the framework of the DW SSI driver, DW SPI
controller supports Tx-only and EEPROM-read modes. The former one just
enables the controller to transmit all the data from the Tx FIFO ignoring
anything retrieved from the MISO lane. The later mode is so called
write-then-read operation: DW SPI controller first pushes out all the data
from the Tx FIFO, after that it'll automatically receive as much data as
has been specified by means of the CTRLR1 register. Both of those modes
can be used to implement the memory operations supported by the SPI-memory
subsystem.
The memory operation implementation is pretty much straightforward, except
a few peculiarities we have had to take into account to make things
working. Since DW SPI controller doesn't provide a way to directly set and
clear the native CS lane level, but instead automatically de-asserts it
when a transfer going on, we have to make sure the Tx FIFO isn't empty
during entire Tx procedure. In addition we also need to read data from the
Rx FIFO as fast as possible to prevent it' overflow with automatically
fetched incoming traffic. The denoted peculiarities get to cause even more
problems if DW SSI controller is equipped with relatively small FIFO and
is connected to a relatively slow system bus (APB) (with respect to the
SPI bus speed). In order to workaround the problems for as much as it's
possible, the memory operation execution procedure collects all the Tx
data into a single buffer and disables the local IRQs to speed the
write-then-optionally-read method up.
Note the provided memory operations are utilized by default only if
a glue driver hasn't provided a custom version of ones and this is not
a DW APB SSI controller with fixed automatic CS toggle functionality.
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-18-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
There seems no reason to restrict testing to ARM, so remove this
constraint to improve test coverage.
Build-tested with allyesconfig on x86.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200904163709.110975-1-alex.dewar90@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The plat-samsung directory and mach-s5pv210 can be build
completely independently, so split the two Kconfig symbols
CONFIG_PLAT_SAMSUNG and CONFIG_ARCH_S5PV210.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-18-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
CONFIG_OF_DYNAMIC and CONFIG_ACPI allow adding SPI devices at runtime
using a DeviceTree overlay or DSDT patch. CONFIG_SPI_SLAVE allows the
same via sysfs.
But there are no precautions to prevent adding a device below a
controller that's being removed. Such a device is unusable and may not
even be able to unbind cleanly as it becomes inaccessible once the
controller has been torn down. E.g. it is then impossible to quiesce
the device's interrupt.
of_spi_notify() and acpi_spi_notify() do hold a ref on the controller,
but otherwise run lockless against spi_unregister_controller().
Fix by holding the spi_add_lock in spi_unregister_controller() and
bailing out of spi_add_device() if the controller has been unregistered
concurrently.
Fixes: ce79d54ae4 ("spi/of: Add OF notifier handler")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.19+
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Link: https://lore.kernel.org/r/a8c3205088a969dc8410eec1eba9aface60f36af.1596451035.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Optimezed mem*io operations are defined for LE platforms, use them.
The ARM and !ARCH_EBSA110 dependencies for COMPILE_TEST were added
only for the _memcpy_fromio()/_memcpy_toio() functions. Drop these
dependencies.
Tested unaligned accesses on both sama5d2 and sam9x60 QSPI controllers
using SPI NOR flashes, everything works ok. The following performance
improvement can be seen when running mtd_speedtest:
sama5d2_xplained (mx25l25635e)
- before:
mtd_speedtest: eraseblock write speed is 983 KiB/s
mtd_speedtest: eraseblock read speed is 6150 KiB/s
- after:
mtd_speedtest: eraseblock write speed is 1055 KiB/s
mtd_speedtest: eraseblock read speed is 20144 KiB/s
sam9x60ek (sst26vf064b)
- before:
mtd_speedtest: eraseblock write speed is 4770 KiB/s
mtd_speedtest: eraseblock read speed is 8062 KiB/s
- after:
mtd_speedtest: eraseblock write speed is 4524 KiB/s
mtd_speedtest: eraseblock read speed is 21186 KiB/s
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200716043139.565734-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series is a subset of "[PATCH v12 0/4] spi: cadence-quadspi: Add
support for the Cadence QSPI controller" by Ramuthevar,Vadivel MuruganX
<vadivel.muruganx.ramuthevar@linux.intel.com> that intended to move
cadence-quadspi driver to spi-mem framework
Those patches were trying to accomplish too many things in a single set
of patches and need to split into smaller patches. This is reduced
version of above series.
Changes that are intended to make migration easy are split into separate
patches. Patches 1 to 3 drop features that cannot be supported under
spi-mem at the moment (backward compatibility is maintained).
Patch 4-5 are trivial cleanups. Patch 6 does the actual conversion to
spi-mem and patch 7 moves the driver to drivers/spi folder.
I have tested both INDAC mode (used by non TI platforms like Altera
SoCFPGA) and DAC mode (used by TI platforms) on TI EVMs.
Patches to move move bindings over to
"Documentation/devicetree/bindings/spi/" directory and also conversion
of bindig doc to YAML will be posted separately. Support for Intel
platform would follow that.
Resend v3:
Rebased onto v5.7-c1
v3:
Split handling of probe deferral into separate patch (out of 5/6)
Split dropping of redundant WREN to separate patch (out of 5/6)
Fix a possible memleak due to lack of spi_master_put()
Parse all SPI slave nodes in cqspi_setup_flash()
Address misc comments from Tudor on v2
Rebase onto latest spi-nor/next
v2:
Rework patch 1/6 to keep "cdns,is-decoded-cs" property supported.
Ramuthevar Vadivel Murugan (2):
mtd: spi-nor: Convert cadence-quadspi to use spi-mem framework
spi: Move cadence-quadspi driver to drivers/spi/
Vignesh Raghavendra (6):
mtd: spi-nor: cadence-quadspi: Make driver independent of flash
geometry
mtd: spi-nor: cadence-quadspi: Provide a way to disable DAC mode
mtd: spi-nor: cadence-quadspi: Don't initialize rx_dma_complete on
failure
mtd: spi-nor: cadence-quadspi: Fix error path on failure to acquire
reset lines
mtd: spi-nor: cadence-quadspi: Handle probe deferral while requesting
DMA channel
mtd: spi-nor: cadence-quadspi: Drop redundant WREN in erase path
drivers/mtd/spi-nor/controllers/Kconfig | 11 -
drivers/mtd/spi-nor/controllers/Makefile | 1 -
drivers/spi/Kconfig | 11 +
drivers/spi/Makefile | 1 +
.../spi-cadence-quadspi.c} | 541 +++++++-----------
5 files changed, 222 insertions(+), 343 deletions(-)
rename drivers/{mtd/spi-nor/controllers/cadence-quadspi.c => spi/spi-cadence-quadspi.c} (74%)
base-commit: b3a9e3b962
--
2.26.2
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Now that cadence-quadspi has been converted to use spi-mem framework,
move it under drivers/spi/
Update license header to match SPI subsystem style
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-9-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for regmap. It makes preparation for supporting
different ways to access the registers.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/1592531021-11412-2-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the SPI driver for the Renesas RPC-IF. It's the "front end" driver
using the "back end" APIs in the main driver to talk to the real hardware.
We only implement the 'spi-mem' interface -- there's no need to implement
the usual SPI driver methods...
Based on the original patch by Mason Yang <masonccyang@mxic.com.tw>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/1ece0e6c-71af-f0f1-709e-571f4b0b4853@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm63xx-hsspi controller is present on several BMIPS SoCs (BCM6318, BCM6328,
BCM6362 and BCM63268).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200615090943.2936839-5-noltari@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm63xx-spi controller is present on several BMIPS SoCs (BCM6358, BCM6362,
BCM6368 and BCM63268).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200615090943.2936839-3-noltari@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since there is a generic method available to initialize the DW SPI DMA
interface on any DT and ACPI-based platforms, which in general can be
designed with not only DW DMAC but with any DMA engine on board, we can
freely remove the CONFIG_DW_DMAC_PCI config from dependency list of
CONFIG_SPI_DW_DMA. Especially seeing that we don't use anything DW DMAC
specific in the new driver.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a preparation patch before adding the DW DMA support into the
DW SPI MMIO driver. We need to unpin the Non-DMA-specific code from the
intended to be generic DW APB SSI DMA code. This isn't that hard,
since the most part of the spi-dw-mid.c driver in fact implements a
generic DMA interface for the DW SPI controller driver. The only Intel
MID specifics concern getting the max frequency from the MRST Clock
Control Unit and fetching the DMA controller channels from
corresponding PCIe DMA controller. Since first one is related with the
SPI interface configuration we moved it' implementation into the
DW PCIe-SPI driver module. After that former spi-dw-mid.c file
can be just renamed to be the DW SPI DMA module optionally compiled in to
the DW APB SSI core driver.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver supports SPI Controller for AMD SOCs.This driver
supports SPI operations using FIFO mode of transfer.
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/1587844788-33997-1-git-send-email-sanju.mehta@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This became again a busy development cycle. There are a few ALSA
core updates (merely API cleanups and sparse fixes), while majority
of other changes are found in ASoC scene.
Here are some highlights:
* ALSA core:
- More helper macros for sparse warning fixes (e.g. bitwise types)
- Slight optimization of PCM OSS locks
- Make common handling for PCM / compress buffers (for SOF)
* ASoC:
- Lots of code refactoring and modernization for (still ongoing)
componentization works
- Conversion of SND_SOC_ALL_CODECS to use imply
- Continued refactoring and fixing of the Intel SOF/SST support,
including the initial (but still incomplete) SoundWire support
- SoundWire and more advanced clocking support for Realtek RT5682
- Support for amlogic GX, Meson 8, Meson 8B and T9015 DAC, Broadcom
DSL/PON, Ingenic JZ4760 and JZ4770, Realtek RL6231, and TI TAS2563
and TLV320ADCX140
* HD-audio:
- Optimizations in HDMI jack handling
- A few new quirks and fixups for Realtek codecs
* USB-audio:
- Delayed registration support
- New quirks for Motu, Kingston, Presonus
-----BEGIN PGP SIGNATURE-----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=fAMQ
-----END PGP SIGNATURE-----
Merge tag 'sound-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became again a busy development cycle. There are few ALSA core
updates (merely API cleanups and sparse fixes), with the majority of
other changes are found in ASoC scene.
Here are some highlights:
ALSA core:
- More helper macros for sparse warning fixes (e.g. bitwise types)
- Slight optimization of PCM OSS locks
- Make common handling for PCM / compress buffers (for SOF)
ASoC:
- Lots of code refactoring and modernization for (still ongoing)
componentization works
- Conversion of SND_SOC_ALL_CODECS to use imply
- Continued refactoring and fixing of the Intel SOF/SST support,
including the initial (but still incomplete) SoundWire support
- SoundWire and more advanced clocking support for Realtek RT5682
- Support for amlogic GX, Meson 8, Meson 8B and T9015 DAC, Broadcom
DSL/PON, Ingenic JZ4760 and JZ4770, Realtek RL6231, and TI TAS2563
and TLV320ADCX140
HD-audio:
- Optimizations in HDMI jack handling
- A few new quirks and fixups for Realtek codecs
USB-audio:
- Delayed registration support
- New quirks for Motu, Kingston, Presonus"
* tag 'sound-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (415 commits)
ALSA: usb-audio: Fix case when USB MIDI interface has more than one extra endpoint descriptor
Revert "ALSA: uapi: Drop asound.h inclusion from asoc.h"
ALSA: hda/realtek - Remove now-unnecessary XPS 13 headphone noise fixups
ALSA: hda/realtek - Set principled PC Beep configuration for ALC256
ALSA: doc: Document PC Beep Hidden Register on Realtek ALC256
ALSA: hda/realtek - a fake key event is triggered by running shutup
ALSA: hda: default enable CA0132 DSP support
ASoC: amd: acp3x-pcm-dma: clean up two indentation issues
ASoC: tlv320adcx140: Remove undocumented property
ASoC: Intel: sof_sdw: Add Volteer support with RT5682 SNDW helper function
ASoC: Intel: common: add match table for TGL RT5682 SoundWire driver
ASoC: Intel: boards: add sof_sdw machine driver
ASoC: Intel: soc-acpi: update topology and driver name for SoundWire platforms
ASoC: rt5682: move DAI clock registry to I2S mode
ASoC: pxa: magician: convert to use i2c_new_client_device()
ASoC: SOF: Intel: hda-ctrl: add reset cycle before parsing capabilities
Asoc: SOF: Intel: hda: check SoundWire wakeen interrupt in irq thread
ASoC: SOF: Intel: hda: add WAKEEN interrupt support for SoundWire
ASoC: SOF: Intel: hda: add parameter to control SoundWire clock stop quirks
ASoC: SOF: Intel: hda: merge IPC, stream and SoundWire interrupt handlers
...
The SPICC controller in Meson-AXG SoC is capable of using
a linear clock divider to reach a much fine tuned range of clocks,
while the old controller only use a power of two clock divider,
result at a more coarse clock range.
Also convert the clock registration into Common Clock Framework.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Link: https://lore.kernel.org/r/20200312133131.26430-4-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset from Chuanhong Guo <gch981213@gmail.com> adds a spi-mem
driver for Mediatek SPI-NOR controller, which already has limited
support by mtk-quadspi. This new driver can make use of full quadspi
capability of this controller.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl5pQmYTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0D9sB/9PBy5hYIWLJOqP3Tegy+si7eEjgYQe
32DvHZRYYL+Oc8OQMGnJYUY5grfriS300TjxeB4MNx8ajVyuaH7e2aIhgTz3oJ6a
YrygFcxEi0LmRT82HyLVxptyblMSo3A8QWOTOqe1aFvJRZjDDKvEIcGCW2RPmtxT
r/EoVVkSv4X+k3GUtYnRBrq12hL+vr1YIjZM05MVu2sDtFXLO2+wotFIODDv15zi
ByBtwhKumKawUOETzGDw4EDV5MJx9nZtswRC4x3hDrLS6au39F/MyP78gpHm8vw+
YfiS5/39rkB6j1QltcP3B9n7joxrgaFAYsLBTZUoE3IjeVTggcKCOSVX
=q5ml
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl5pQt4THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0BFqB/9jBg5bNy9mNXljELZ7RKCtbn9CThYk
NvccckUJnjaTxSccGcGEetfFtoVvM4IJ8ffiL6gBrNDgvuSbedLkboqlftRRbkE2
tvxnfjKGeiVIHXcXG0kzrVMDPPncYy+o8nQMJ8b/v+VFeLah6LCo0nT4t54LPvfZ
52Nncdr8jAnjoet7t2CX2nJrhTOPUGhC7HxbwOyu2HOOd5nWmYAdT4UZo4Vdv1g9
L1knLoZctpvCpql/mUWdOAqQbD0bD0vT3FKQaq6C6kAeE+kMWSGdPgYxyFdBEVXi
uOmaqU7lHt2bsr6TRbOpw4ON0PzQtzZ/YhW2XEPJd6uc3GWy//qEyqgO
=qoqi
-----END PGP SIGNATURE-----
Merge tag 'mtk-mtd-spi-move' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-5.7
spi: Rewrite mtk-quadspi spi-nor driver with spi-mem
This patchset from Chuanhong Guo <gch981213@gmail.com> adds a spi-mem
driver for Mediatek SPI-NOR controller, which already has limited
support by mtk-quadspi. This new driver can make use of full quadspi
capability of this controller.
This is a driver for mtk spi-nor controller using spi-mem interface.
The same controller already has limited support provided by mtk-quadspi
driver under spi-nor framework and this new driver is a replacement
for the old one.
Comparing to the old driver, this driver has following advantages:
1. It can handle any full-duplex spi transfer up to 6 bytes, and
this is implemented using generic spi interface.
2. It take account into command opcode properly. The reading routine
in this controller can only use 0x03 or 0x0b as opcode on 1-1-1
transfers, but old driver doesn't implement this properly. This
driver checks supported opcode explicitly and use (1) to perform
unmatched operations.
3. It properly handles SFDP reading. Old driver can't read SFDP
due to the bug mentioned in (2).
4. It can do 1-2-2 and 1-4-4 fast reading on spi-nor. These two ops
requires parsing SFDP, which isn't possible in old driver. And
the old driver is only flagged to support 1-1-2 mode.
5. It takes advantage of the DMA feature in this controller for
long reads and supports IRQ on DMA requests to free cpu cycles
from polling status registers on long DMA reading. It achieves
up to 17.5MB/s reading speed (1-4-4 mode) which is way faster
than the old one. IRQ is implemented as optional to maintain
backward compatibility.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200306085052.28258-3-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
By selecting MTD_SPI_NOR for SPI_HISI_SFC_V3XX, we may introduce unmet
dependencies:
WARNING: unmet direct dependencies detected for MTD_SPI_NOR
Depends on [m]: MTD [=m] && SPI_MASTER [=y]
Selected by [y]:
- SPI_HISI_SFC_V3XX [=y] && SPI [=y] && SPI_MASTER [=y] && (ARM64 && ACPI [=y] || COMPILE_TEST [=y]) && HAS_IOMEM [=y]
Since MTD_SPI_NOR is only selected by SPI_HISI_SFC_V3XX for practical
reasons - slave devices use the spi-nor driver, enabled by MTD_SPI_NOR -
just drop it.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1583948115-239907-1-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There exists a set of SPI controllers on some POWER processors that may
be accessed through the FSI bus. Add a driver to traverse the FSI CFAM
engine that can access and drive the SPI controllers. This driver would
typically be used by a baseboard management controller (BMC).
The SPI controllers operate by means of programming a sequencing engine
which automatically manages the usual SPI protocol buses. The driver
programs each transfer into the sequencer as various operations
specifying the slave chip and shifting data in and out on the lines.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20200306194118.18581-3-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit a2ca53b52e ("spi: Add HiSilicon v3xx SPI NOR flash
controller driver") likely inadvertently used a select statement
with a CONFIG_ prefix, remove the prefix.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/f8ac6b32a29b9a05b58a7e58ffe8b780642abbf1.camel@perches.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a SPI device driver that sits in-band and provides a SPI controller
which supports chip selects via a mux-control. This enables extra SPI
devices to be connected with limited native chip selects.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200204032838.20739-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds driver for SPI controller found in Qualcomm Atheros
AR934x/QCA95xx SoCs.
This controller is a superset of the already supported qca,ar7100-spi.
Besides the bit-bang mode in spi-ath79.c, this new controller added
a new "shift register" mode, allowing faster spi operations.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200210034152.49063-2-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the driver for the HiSilicon v3xx SPI NOR flash controller, commonly
found in hi16xx chipsets.
This is a different controller than that in drivers/mtd/spi-nor/hisi-sfc.c;
indeed, the naming for that driver is poor, since it is really known as
FMC, and can support other memory technologies.
The driver module name is "hisi-sfc-v3xx", as recommended by HW designer,
being an attempt to provide a distinct name - v3xx being the unique
controller versioning.
Only ACPI firmware is supported.
DMA is not supported, and we just use polling mode for operation
completion notification.
The driver uses the SPI MEM OPs.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1575900490-74467-3-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191120133916.13595-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
