GPIO17_SDATA_IN_1 and GPIO36_SDATA_IN_1 are originally designed for the 2nd
codec but unused on the board, yet they are initialized incorrectly by the
bootloader as the SDATA_IN_1 alternate function, thus causing AC97 fail to
work. Fix this issue by configuring these pins as normal GPIO to avoid the
noise from these pins being treated as signals from the 2nd codec.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
cpufreq drivers for pxa2xx/3xx are now built-in automatically as soon as
CPU_FREQ is enabled.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
ARCH_PXA selects HAVE_CLK and COMMON_CLKDEV twice in arch/arm/Kconfig.
Remove the second entry.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
pxa_gpio_irq_type() and pxa_unmask_muxed_gpio() will touch non-muxed GPIOs
(0 and 1 on PXA2xx/PXA3xx) bits in GRERx and GFERx, which is incorrect.
Actually, only those bits should get updated if the corresponding bits are
set in c->irq_mask as well. Fix this by updating only those relevant bits.
Reported-and-tested-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Update defconfigs for 2.6.30-rc3
m68k,m68knommu: Wire up preadv and pwritev
scsi: a4000 - Correct driver unregistration in case of failure
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] update default configuration.
[S390] omit frame pointers on s390 when possible
[S390] Use tape_generic_offline directly.
[S390] /proc/stat idle field for idle cpus
[S390] appldata: avoid deadlock with appldata_mem
[S390] ipl: fix compile breakage
Update the defconfig for the ASB2303 evaluation board.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Fix bus type probing for ESP and LE devices.
sparc32: Update defconfig.
sparc64: Update defconfig.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix modular build of ide-pmac when mediabay is built in
powerpc/pasemi: Fix build error on UP
powerpc: Make macintosh/mediabay driver depend on CONFIG_BLOCK
maintainers: Fix PS3 patterns
powerpc/ps3: Fix CONFIG_PS3_FLASH=n build warning
powerpc/32: Don't clobber personality flags on exec
powerpc: Fix crash on CPU hotplug
powerpc/85xx: Remove defconfigs that mpc85xx_{smp_}defconfig cover
powerpc/85xx: Added SMP defconfig
powerpc/85xx: Enabled a bunch of FSL specific drivers/options
powerpc/85xx: Updated generic mpc85xx_defconfig
powerpc: don't disable SATA interrupts on Freescale MPC8610 HPCD
fsl_rio: Pass the proper device to dma mapping routines
powerpc: Fix of_node_put() exit path in of_irq_map_one()
powerpc/5200: defconfig updates
powerpc/5200: Add FLASH nodes to lite5200 device tree
powerpc/device-tree: Document MTD nodes with multiple "reg" tuples
powerpc/of-device-tree: Factor MTD physmap bindings out of booting-without-of
powerpc/5200: Bring the legacy fsl_spi_platform_data hooks back
Symbols like SOFT_RESET are way too generic to be exported at large.
To avoid this, let's move the mbus bridge register defines into a
separate file and include it where needed. This affects mach-kirkwood,
mach-loki, mach-mv78xx0 and mach-orion5x simultaneously as they all
share code in plat-orion which relies on those defines.
Some other defines have been moved to narrower scopes, or simply deleted
when they had no user.
This fixes compilation problem with mpt2sas on the above listed
platforms.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The cpu idle field in the output of /proc/stat is too small for cpus
that have been idle for more than a tick. Add the architecture hook
arch_idle_time that allows to add the not accounted idle time of a
sleeping cpu without waking the cpu.
The s390 implementation of arch_idle_time uses the already existing
s390_idle_data per_cpu variable to find the sleep time of a neighboring
idle cpu.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The appldata_ops callbacks are called with a spin_lock held. But the
appldata_mem callback then calls all_vm_events(), which calls
get_online_cpus(), which might sleep. This possible deadlock is fixed
by using a mutex instead of a spin_lock.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix this for !CONFIG_SMP:
arch/s390/kernel/ipl.c: In function 'stop_run':
arch/s390/kernel/ipl.c:1461: error: implicit declaration of function 'signal_processor'
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Properly unregister cpufreq notifier on onload if it was registered
during init.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Not releasing the time_page causes a leak of that page or the compound
page it is situated in.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Reorder locking as down_read() may return with local interrupts enabled,
which means we could go into vti_vcpu_run() with interrupts enabled.
This caused random crashes on the Altix as the timer interrupt tried
to read a memory mapped clock source, for which the TLB had not yet been
reinstated in the exit, before ipsr was retored.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Acked-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If there is a dummy "espdma" or "ledma" parent device above ESP scsi
or LE ethernet device nodes, we have to match the bus as SBUS.
Otherwise the address and size cell counts are wrong and we don't
calculate the final physical device resource values correctly at all.
Commit 5280267c1d ("sparc: Fix handling
of LANCE and ESP parent nodes in of_device.c") was meant to fix this
problem, but that only influences the inner loop of
build_device_resources(). We need this logic to also kick in at the
beginning of build_device_resources() as well, when we make the first
attempt to determine the device's immediate parent bus type for 'reg'
property element extraction.
Based almost entirely upon a patch by Friedrich Oslage.
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
A non-SMP version of smp_send_stop() is now included in smp.h.
Remove the unneeded definition in the pasemi setup.c.
Fixes build errors like these when CONFIG_SMP=n:
arch/powerpc/platforms/pasemi/setup.c:48: error: redefinition of ‘smp_send_stop’
include/linux/smp.h:125: error: previous definition of 'smp_send_stop' was here
Reported-by: subrata@linux.vnet.ibm.com
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix build warnings like these when CONFIG_PS3_FLASH=n:
arch/powerpc/platforms/ps3/os-area.c: warning: 'update_flash_db' defined but not used
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that ppc32 implements address randomization it also wants to inherit
personality flags like ADDR_NO_RANDOMIZE across exec, for things like
`setarch ppc -R' to work. But the ppc32 version of SET_PERSONALITY
forcefully sets PER_LINUX, clearing all personality flags. So be
careful about preserving the flags.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
early_init_mmu_secondary() is called at CPU hotplug time, so it
must be marked as __cpuinit, not __init.
Caused by 757c74d2 ("powerpc/mm: Introduce early_init_mmu() on 64-bit").
Tested-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In non-SMP mode, the variable section attribute specified by DECLARE_PER_CPU()
does not agree with that specified by DEFINE_PER_CPU(). This means that
architectures that have a small data section references relative to a base
register may throw up linkage errors due to too great a displacement between
where the base register points and the per-CPU variable.
On FRV, the .h declaration says that the variable is in the .sdata section, but
the .c definition says it's actually in the .data section. The linker throws
up the following errors:
kernel/built-in.o: In function `release_task':
kernel/exit.c:78: relocation truncated to fit: R_FRV_GPREL12 against symbol `per_cpu__process_counts' defined in .data section in kernel/built-in.o
kernel/exit.c:78: relocation truncated to fit: R_FRV_GPREL12 against symbol `per_cpu__process_counts' defined in .data section in kernel/built-in.o
To fix this, DECLARE_PER_CPU() should simply apply the same section attribute
as does DEFINE_PER_CPU(). However, this is made slightly more complex by
virtue of the fact that there are several variants on DEFINE, so these need to
be matched by variants on DECLARE.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the vast majority of 85xx platforms are UP we introduce a new SMP
config for the few platforms that have more than one core. Beyond
CONFIG_SMP=y and its dependencies this should be identical to
mpc85xx_defconfig.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Got this warning from Kconfig:
boolean symbol INPUT tested for 'm'? test forced to 'n'
because INPUT is tristate, not bool.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Insert PCI root bus resources for the FRV-based MB93090 development kit
motherboard. This is required because the CPU's window onto the PCI bus
address space is considerably smaller than the CPU's full address space
and non-PCI devices lie outside of the PCI window that we might want to
access.
Without this patch, the PCI root bus uses the platform-level bus
resources, and these are then confined to the PCI window, thus making
platform_device_add() reject devices outside of this window.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ULI 1575 PCI quirk function for the Freescale MPC8610 HPCD was disabling
the SATA INTx interrupt, even when SATA support was enabled. This was safe,
because the SATA driver re-enabled it. But with commit a5bfc471 ("ahci: drop
intx manipulation on msi enable"), the driver no longer does this, and so SATA
support on the 8610 HPCD is broken.
The original quirk function disabled INTx because it caused some other
interrupt problem during early development on this board, but no one remembers
any more what that problem was, and it doesn't seem to occur any more.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The driver should pass a device that specifies internal DMA ops, but
currently NULL pointer is passed, therefore following bug appears
during boot up:
------------[ cut here ]------------
Kernel BUG at c0018a7c [verbose debug info unavailable]
Oops: Exception in kernel mode, sig: 5 [#1]
[...]
NIP [c0018a7c] fsl_rio_doorbell_init+0x34/0x60
LR [c0018a70] fsl_rio_doorbell_init+0x28/0x60
Call Trace:
[ef82bda0] [c0018a70] fsl_rio_doorbell_init+0x28/0x60 (unreliable)
[ef82bdc0] [c0019160] fsl_rio_setup+0x6b8/0x84c
[ef82be20] [c02d28ac] fsl_of_rio_rpn_probe+0x30/0x50
[ef82be40] [c0234f20] of_platform_device_probe+0x5c/0x84
[...]
---[ end trace 561bb236c800851f ]---
This patch fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
reiserfs: fix j_last_flush_trans_id type
fs: Mark get_filesystem_list() as __init function.
kill vfs_stat_fd / vfs_lstat_fd
Separate out common fstatat code into vfs_fstatat
ecryptfs: use memdup_user()
ncpfs: use memdup_user()
xfs: use memdup_user()
sysfs: use memdup_user()
btrfs: use memdup_user()
xattr: use memdup_user()
autofs4: use memchr() in invalid_string()
Documentation/filesystems: remove out of date reference to BKL being held
Fix i_mutex vs. readdir handling in nfsd
fs/compat_ioctl: fix build when !BLOCK
Fix autofs_expire()
No need for crossing to mountpoint in audit_tag_tree()
Safer nfsd_cross_mnt()
Touch all affected namespaces on propagation of mount
Fix AUTOFS_DEV_IOCTL_REQUESTER_CMD
This is a version incorporating Christoph's suggestion.
Separate out common *fstatat functionality into a single function
instead of duplicating it all over the code.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
mmap2 uses a fixed page shift of 12, regardless of the PAGE_SIZE setting.
Fix up the mmap2 code to add some sanity checks on the mapping, and to
update pgoff accordingly.
Error handling bits based on 4280e3126f
("frv: fix mmap2 error handling").
Signed-off-by: Toshinobu Sugioka <sugioka@itonet.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] fix allmodconfig compilation breakage.
[IA64] smp_flush_tlb_mm() should only send IPI's to cpus in cpu_vm_mask
[IA64] export smp_send_reschedule
This patch fixes the following compilation error caused by recursive
inclusion of kernel.h which defines BUILD_BUG_ON().
In this case, the case it catches will be caught by the case
CONFIG_PARAVIRT=n, so removing it would not hurt compile time check
very much. So fix the breakage by removing it.
CC arch/ia64/kernel/asm-offsets.s
In file included from include/linux/bitops.h:17,
from include/linux/kernel.h:15,
from include/linux/sched.h:52,
from arch/ia64/kernel/asm-offsets.c:9:
arch/ia64/include/asm/bitops.h: In function 'set_bit':
arch/ia64/include/asm/bitops.h:47: error: implicit declaration of function 'BUILD_BUG_ON'
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>
