The messages should be different depending on the type of error.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Use accessor for_each_pci_msi_entry() to access MSI device list, so we
could easily move msi_list from struct pci_dev into struct device
later.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: xen-devel@lists.xenproject.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Stuart Yoder <stuart.yoder@freescale.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1436428847-8886-6-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unlike MSI, which is configured via registers in the MSI capability in
Configuration Space, MSI-X is configured via tables in Memory Space.
These MSI-X tables are mapped by a device BAR, and if no Memory Space
has been assigned to the BAR, MSI-X cannot be used.
Fail MSI-X setup if no space has been assigned for the BAR.
Previously, we ioremapped the MSI-X table even if the resource hadn't been
assigned. In this case, the resource address is undefined (and is often
zero), which may lead to warnings or oopses in this path:
pci_enable_msix
msix_capability_init
msix_map_region
ioremap_nocache
The PCI core sets resource flags to zero when it can't assign space for the
resource (see reset_resource()). There are also some cases where it sets
the IORESOURCE_UNSET flag, e.g., pci_reassigndev_resource_alignment(),
pci_assign_resource(), etc. So we must check for both cases.
[bhelgaas: changelog]
Reported-by: Zhang Jukuo <zhangjukuo@huawei.com>
Tested-by: Zhang Jukuo <zhangjukuo@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Xen overrides __acpi_register_gsi and leaves __acpi_unregister_gsi as is.
That means, an IRQ allocated by acpi_register_gsi_xen_hvm() or
acpi_register_gsi_xen() will be freed by acpi_unregister_gsi_ioapic(),
which may cause undesired effects. So override __acpi_unregister_gsi to
NULL for safety.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: xen-devel@lists.xenproject.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Graeme Gregory <graeme.gregory@linaro.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Link: http://lkml.kernel.org/r/1421720467-7709-4-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently Xen Domain0 has special treatment for ACPI SCI interrupt,
that is initialize irq for ACPI SCI at early stage in a special way as:
xen_init_IRQ()
->pci_xen_initial_domain()
->xen_setup_acpi_sci()
Allocate and initialize irq for ACPI SCI
Function xen_setup_acpi_sci() calls acpi_gsi_to_irq() to get an irq
number for ACPI SCI. But unfortunately acpi_gsi_to_irq() depends on
IOAPIC irqdomains through following path
acpi_gsi_to_irq()
->mp_map_gsi_to_irq()
->mp_map_pin_to_irq()
->check IOAPIC irqdomain
For PV domains, it uses Xen event based interrupt manangement and
doesn't make uses of native IOAPIC, so no irqdomains created for IOAPIC.
This causes Xen domain0 fail to install interrupt handler for ACPI SCI
and all ACPI events will be lost. Please refer to:
https://lkml.org/lkml/2014/12/19/178
So the fix is to get rid of special treatment for ACPI SCI, just treat
ACPI SCI as normal GSI interrupt as:
acpi_gsi_to_irq()
->acpi_register_gsi()
->acpi_register_gsi_xen()
->xen_register_gsi()
With above change, there's no need for xen_setup_acpi_sci() anymore.
The above change also works with bare metal kernel too.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: xen-devel@lists.xenproject.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/1421720467-7709-2-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Fully support non-coherent devices on ARM by introducing the
mechanisms to request the hypervisor to perform the required cache
maintainance operations.
- A number of pciback bug fixes and cleanups. Notably a deadlock fix
if a PCI device was manually uunbound and a fix for incorrectly
restoring state after a function reset.
- In x86 PVHVM guests, use the APIC for interrupts if this has been
virtualized by the hardware. This reduces the number of interrupt-
related VM exits on such hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUiYb+AAoJEFxbo/MsZsTRwmEH+gNaJz5r8gIJlq8Q51+nOIs4
Gw6HdjUB5MOT47vDV4treEOx0Bk8hYTfgWUWvAC81JMJ1sMWOVrUGuG/0lmzaomW
zXvSk+o0n4LafwEhHb8LIccZMbaH7f9o3PNdNchrTkPrIl8Gf2nmBXCkDsT4mRye
5ZFpc4ntgBrznh3baPYDS8PCAmlyZ0uVEnz1ofYI6S80dC13siEiPG0c9TrNEKzO
glhvgCRmR0C4ZNLblM36HWBEqrdLuGCoNJSH+7okygyP2TLD3aO4R+9aD5JWYNdf
fO2WmivX/zK+UGVAElrLx+rb8R2dv3ddeaE5piZhIBUieopIWJd32L3LhQORdtc=
=N6DP
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.19-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen features and fixes from David Vrabel:
- Fully support non-coherent devices on ARM by introducing the
mechanisms to request the hypervisor to perform the required cache
maintainance operations.
- A number of pciback bug fixes and cleanups. Notably a deadlock fix
if a PCI device was manually uunbound and a fix for incorrectly
restoring state after a function reset.
- In x86 PVHVM guests, use the APIC for interrupts if this has been
virtualized by the hardware. This reduces the number of interrupt-
related VM exits on such hardware.
* tag 'stable/for-linus-3.19-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (26 commits)
Revert "swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single"
xen/pci: Use APIC directly when APIC virtualization hardware is available
xen/pci: Defer initialization of MSI ops on HVM guests
xen-pciback: drop SR-IOV VFs when PF driver unloads
xen/pciback: Restore configuration space when detaching from a guest.
PCI: Expose pci_load_saved_state for public consumption.
xen/pciback: Remove tons of dereferences
xen/pciback: Print out the domain owning the device.
xen/pciback: Include the domain id if removing the device whilst still in use
driver core: Provide an wrapper around the mutex to do lockdep warnings
xen/pciback: Don't deadlock when unbinding.
swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single
swiotlb-xen: call xen_dma_sync_single_for_device when appropriate
swiotlb-xen: remove BUG_ON in xen_bus_to_phys
swiotlb-xen: pass dev_addr to xen_dma_unmap_page and xen_dma_sync_single_for_cpu
xen/arm: introduce GNTTABOP_cache_flush
xen/arm/arm64: introduce xen_arch_need_swiotlb
xen/arm/arm64: merge xen/mm32.c into xen/mm.c
xen/arm: use hypercall to flush caches in map_page
xen: add a dma_addr_t dev_addr argument to xen_dma_map_page
...
When hardware supports APIC/x2APIC virtualization we don't need to use
pirqs for MSI handling and instead use APIC since most APIC accesses
(MMIO or MSR) will now be processed without VMEXITs.
As an example, netperf on the original code produces this profile
(collected wih 'xentrace -e 0x0008ffff -T 5'):
342 cpu_change
260 CPUID
34638 HLT
64067 INJ_VIRQ
28374 INTR
82733 INTR_WINDOW
10 NPF
24337 TRAP
370610 vlapic_accept_pic_intr
307528 VMENTRY
307527 VMEXIT
140998 VMMCALL
127 wrap_buffer
After applying this patch the same test shows
230 cpu_change
260 CPUID
36542 HLT
174 INJ_VIRQ
27250 INTR
222 INTR_WINDOW
20 NPF
24999 TRAP
381812 vlapic_accept_pic_intr
166480 VMENTRY
166479 VMEXIT
77208 VMMCALL
81 wrap_buffer
ApacheBench results (ab -n 10000 -c 200) improve by about 10%
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
If the hardware supports APIC virtualization we may decide not to use
pirqs and instead use APIC/x2APIC directly, meaning that we don't want
to set x86_msi.setup_msi_irqs and x86_msi.teardown_msi_irq to
Xen-specific routines. However, x2APIC is not set up by the time
pci_xen_hvm_init() is called so we need to postpone setting these ops
until later, when we know which APIC mode is used.
(Note that currently x2APIC is never initialized on HVM guests. This
may change in the future)
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Rename write_msi_msg() to pci_write_msi_msg() to mark it as PCI
specific.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename __read_msi_msg() to __pci_read_msi_msg() and kill unused
read_msi_msg(). It's a preparation to separate generic MSI code from
PCI core.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The problem fixed by 0e4ccb1505 ("PCI: Add x86_msi.msi_mask_irq() and
msix_mask_irq()") has been fixed in a simpler way by a previous commit
("PCI/MSI: Add pci_msi_ignore_mask to prevent writes to MSI/MSI-X Mask
Bits").
The msi_mask_irq() and msix_mask_irq() x86_msi_ops added by 0e4ccb1505
are no longer needed, so revert the commit.
default_msi_mask_irq() and default_msix_mask_irq() were added by
0e4ccb1505 and are still used by s390, so keep them for now.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: xen-devel@lists.xenproject.org
MSI-X vector Mask Bits are in MSI-X Tables in PCI memory space. Xen PV
guests can't write to those tables. MSI vector Mask Bits are in PCI
configuration space. Xen PV guests can write to config space, but those
writes are ignored.
Commit 0e4ccb1505 ("PCI: Add x86_msi.msi_mask_irq() and
msix_mask_irq()") added a way to override default_mask_msi_irqs() and
default_mask_msix_irqs() so they can be no-ops in Xen guests, but this is
more complicated than necessary.
Add "pci_msi_ignore_mask" in the core PCI MSI code. If set,
default_mask_msi_irqs() and default_mask_msix_irqs() return without doing
anything. This is less flexible, but much simpler.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: xen-devel@lists.xenproject.org
Some platforms, such as Intel MID and mshypv, do not support legacy
interrupt controllers. So count legacy IRQs by legacy_pic->nr_legacy_irqs
instead of hard-coded NR_IRQS_LEGACY.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: xen-devel@lists.xenproject.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Link: http://lkml.kernel.org/r/1402302011-23642-20-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add support for MSI message groups for Xen Dom0 using the
MAP_PIRQ_TYPE_MULTI_MSI pirq map type.
In order to keep track of which pirq is the first one in the group all
pirqs in the MSI group except for the first one have the newly
introduced PIRQ_MSI_GROUP flag set. This prevents calling
PHYSDEVOP_unmap_pirq on them, since the unmap must be done with the
first pirq in the group.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Change x86_msi.restore_msi_irqs(struct pci_dev *dev, int irq) to
x86_msi.restore_msi_irqs(struct pci_dev *dev).
restore_msi_irqs() restores multiple MSI-X IRQs, so param 'int irq' is
unneeded. This makes code more consistent between vm and bare metal.
Dom0 MSI-X restore code can also be optimized as XEN only has a hypercall
to restore all MSI-X vectors at one time.
Tested-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Certain platforms do not allow writes in the MSI-X BARs to setup or tear
down vector values. To combat against the generic code trying to write to
that and either silently being ignored or crashing due to the pagetables
being marked R/O this patch introduces a platform override.
Note that we keep two separate, non-weak, functions default_mask_msi_irqs()
and default_mask_msix_irqs() for the behavior of the arch_mask_msi_irqs()
and arch_mask_msix_irqs(), as the default behavior is needed by x86 PCI
code.
For Xen, which does not allow the guest to write to MSI-X tables - as the
hypervisor is solely responsible for setting the vector values - we
implement two nops.
This fixes a Xen guest crash when passing a PCI device with MSI-X to the
guest. See the bugzilla for more details.
[bhelgaas: add bugzilla info]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=64581
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
CC: Zhenzhong Duan <zhenzhong.duan@oracle.com>
We now cache the MSI-X capability offset in the struct pci_dev, so no
need to find the capability again.
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
PCI_MSIX_FLAGS_BIRMASK is mis-named because the BIR mask is in the
Table Offset register, not the flags ("Message Control" per spec)
register.
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
For quite a few Xen versions, this wasn't the IRQ vector anymore
anyway, and it is not being used by the kernel for anything. Hence
drop the field from struct irq_info, and respective function
parameters.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
There is no hypercall to setup multiple MSI per PCI device.
As such with these two new commits:
- 08261d87f7
PCI/MSI: Enable multiple MSIs with pci_enable_msi_block_auto()
- 5ca72c4f7c
AHCI: Support multiple MSIs
we would call the PHYSDEVOP_map_pirq 'nvec' times with the same
contents of the PCI device. Sander discovered that we would get
the same PIRQ value 'nvec' times and return said values to the
caller. That of course meant that the device was configured only
with one MSI and AHCI would fail with:
ahci 0000:00:11.0: version 3.0
xen: registering gsi 19 triggering 0 polarity 1
xen: --> pirq=19 -> irq=19 (gsi=19)
(XEN) [2013-02-27 19:43:07] IOAPIC[0]: Set PCI routing entry (6-19 -> 0x99 -> IRQ 19 Mode:1 Active:1)
ahci 0000:00:11.0: AHCI 0001.0200 32 slots 4 ports 6 Gbps 0xf impl SATA mode
ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
ahci: probe of 0000:00:11.0 failed with error -22
That is b/c in ahci_host_activate the second call to
devm_request_threaded_irq would return -EINVAL as we passed in
(on the second run) an IRQ that was never initialized.
CC: stable@vger.kernel.org
Reported-and-Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
PV on HVM guests map GSIs into event channels. At restore time the
event channels are resumed by restore_pirqs.
Device drivers might try to register the same GSI again through ACPI at
restore time, but the GSI has already been mapped and bound by
restore_pirqs. This patch detects these situations and avoids
mapping the same GSI multiple times.
Without this patch we get:
(XEN) irq.c:2235: dom4: pirq 23 or emuirq 28 already mapped
and waste a pirq.
CC: stable@kernel.org
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
- PV multiconsole support, so that there can be hvc1, hvc2, etc;
- P-state and C-state power management driver that uploads said
power management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPZ0qkAAoJEFjIrFwIi8fJjCgH/jeJ39E8ML8DP9tCS2HQnMqM
uTEjLcqvoJ7sEhHvtBLPeG2p0jyBvOWjLbSc7P8nESBAMPvSYol8L6WqfWrdSU4r
lHrma2sg9UYzRog5NyxAgkp7bBsBBFOnhVL3Cxb5Ig78cPWzeSWGpqGZ8M/d51Wf
1iE0tHuU4DpN+fg1SZqPqEm8ecEJ/eSrVTnyTx/Qo2Ak+Zw98SqzX7SV5lo8mudd
WFL1F2K9FyTNk79ndGhqFt36x6nEbFgMLbmCDWumLuWN6bMd1Uq0wNkCqW4F1h28
3yqnY+rfQh4y3eXK1B9nttCUTs+/66U5ZWrT6B1IJumGTAIqcWfgeUX/Vn/HVC4=
=tfMc
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen updates from Konrad Rzeszutek Wilk:
"which has three neat features:
- PV multiconsole support, so that there can be hvc1, hvc2, etc; This
can be used in HVM and in PV mode.
- P-state and C-state power management driver that uploads said power
management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
There is one thing in the Kconfig that you won't like: "default y
if (X86_ACPI_CPUFREQ = y || X86_POWERNOW_K8 = y)" (note, that it
all depends on CONFIG_XEN which depends on CONFIG_PARAVIRT which by
default is off). I've a fix to convert that boolean expression
into "default m" which I am going to post after the cpufreq git
pull - as the two patches to make this work depend on a fix in Dave
Jones's tree.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx"
Fix up trivial conflicts in drivers/tty/hvc/hvc_xen.c due to changes to
a removed commit.
* tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen kconfig: relax INPUT_XEN_KBDDEV_FRONTEND deps
xen/acpi-processor: C and P-state driver that uploads said data to hypervisor.
xen: constify all instances of "struct attribute_group"
xen/xenbus: ignore console/0
hvc_xen: introduce HVC_XEN_FRONTEND
hvc_xen: implement multiconsole support
hvc_xen: support PV on HVM consoles
xenbus: don't free other end details too early
xen/enlighten: Expose MWAIT and MWAIT_LEAF if hypervisor OKs it.
xen/setup/pm/acpi: Remove the call to boot_option_idle_override.
xenbus: address compiler warnings
xen: use this_cpu_xxx replace percpu_xxx funcs
xen/pciback: Support pci_reset_function, aka FLR or D3 support.
pci: Introduce __pci_reset_function_locked to be used when holding device_lock.
xen: Utilize the restore_msi_irqs hook.
to make a hypercall to restore the vectors in the MSI/MSI-X
configuration space.
Signed-off-by: Tang Liang <liang.tang@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* 'stable/drivers-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus: don't rely on xen_initial_domain to detect local xenstore
xenbus: Fix loopback event channel assuming domain 0
xen/pv-on-hvm:kexec: Fix implicit declaration of function 'xen_hvm_domain'
xen/pv-on-hvm kexec: add xs_reset_watches to shutdown watches from old kernel
xen/pv-on-hvm kexec: update xs_wire.h:xsd_sockmsg_type from xen-unstable
xen/pv-on-hvm kexec+kdump: reset PV devices in kexec or crash kernel
xen/pv-on-hvm kexec: rebind virqs to existing eventchannel ports
xen/pv-on-hvm kexec: prevent crash in xenwatch_thread() when stale watch events arrive
* 'stable/drivers.bugfixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Check if the device is found instead of blindly assuming so.
xen/pciback: Do not dereference psdev during printk when it is NULL.
xen: remove XEN_PLATFORM_PCI config option
xen: XEN_PVHVM depends on PCI
xen/pciback: double lock typo
xen/pciback: use mutex rather than spinlock in vpci backend
xen/pciback: Use mutexes when working with Xenbus state transitions.
xen/pciback: miscellaneous adjustments
xen/pciback: use mutex rather than spinlock in passthrough backend
xen/pciback: use resource_size()
* 'stable/pci.fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: support multi-segment systems
xen-swiotlb: When doing coherent alloc/dealloc check before swizzling the MFNs.
xen/pci: make bus notifier handler return sane values
xen-swiotlb: fix printk and panic args
xen-swiotlb: Fix wrong panic.
xen-swiotlb: Retry up three times to allocate Xen-SWIOTLB
xen-pcifront: Update warning comment to use 'e820_host' option.
There are three different modes: PV, HVM, and initial domain 0. In all
the cases we would return -1 for failure instead of a proper error code.
Fix this by propagating the error code from the generic IRQ code.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Now that the hypercall interface changes are in -unstable, make the
kernel side code not ignore the segment (aka domain) number anymore
(which results in pretty odd behavior on such systems). Rather, if
only the old interfaces are available, don't call them for devices on
non-zero segments at all.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
[v1: Edited git description]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In the past we would only use the function's value if the
returned value was not equal to 'acpi_sci_override_gsi'. Meaning
that the INT_SRV_OVR values for global and source irq were different.
But it is OK to use the function's value even when the global
and source irq are the same.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In the past (2.6.38) the 'xen_allocate_pirq_gsi' would allocate
an entry in a Linux IRQ -> {XEN_IRQ, type, event, ..} array. All
of that has been removed in 2.6.39 and the Xen IRQ subsystem uses
an linked list that is populated when the call to
'xen_allocate_irq_gsi' (universally done from any of the xen_bind_*
calls) is done. The 'xen_allocate_pirq_gsi' is a NOP and there is
no need for it anymore so lets remove it.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
As the code paths that are guarded by CONFIG_XEN_DOM0 already depend
on CONFIG_ACPI so the extra #ifdef is not required. The earlier
patch that added them in had done its job.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
.. which means we can preset of NR_IRQS_LEGACY interrupts using
the 'acpi_get_override_irq' API before this loop.
This means that we can get the IRQ's polarity (and trigger) from either
the ACPI (or MP); or use the default values. This fixes a bug if we did
not have an IOAPIC we would not been able to preset the IRQ's polarity
if the MP table existed.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Since they are only called once and the rest of the pci_xen_*
functions follow the same pattern of setup.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In the past we would guard those code segments to be dependent
on CONFIG_XEN_DOM0 (which depends on CONFIG_ACPI) so this patch is
not stricly necessary. But the next patch will merge common
HVM and initial domain code and we want to make sure the CONFIG_ACPI
dependency is preserved - as HVM code does not depend on CONFIG_XEN_DOM0.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Update the out-dated comment at the beginning of the file.
Also provide the copyrights of folks who have been contributing
to this code lately.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The file is hard to read. Move the code around so that
the contents of it follows a uniform format:
- setup GSIs - PV, HVM, and initial domain case
- then MSI/MSI-x setup - PV, HVM and then initial domain case.
- then MSI/MSI-x teardown - same order.
- lastly, the __init functions in PV, HVM, and initial domain order.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Previously we would check for acpi_sci_override_gsi == gsi every time
a PCI device was enabled. That works during early bootup, but later
on it could lead to triggering unnecessarily the acpi_gsi_to_irq(..) lookup.
The reason is that acpi_sci_override_gsi was declared in __initdata and
after early bootup could contain bogus values.
This patch moves the check for acpi_sci_override_gsi to the
site where the ACPI SCI is preset.
CC: stable@kernel.org
Reported-by: Raghavendra D Prabhu <rprabhu@wnohang.net>
Tested-by: Raghavendra D Prabhu <rprabhu@wnohang.net>
[http://lists.xensource.com/archives/html/xen-devel/2011-07/msg00154.html]
Suggested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In the past we would use the GSI value to preset the ACPI SCI
IRQ which worked great as GSI == IRQ:
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
While that is most often seen, there are some oddities:
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
which means that GSI 20 (or pin 20) is to be overriden for IRQ 9.
Our code that presets the interrupt for ACPI SCI however would
use the GSI 20 instead of IRQ 9 ending up with:
xen: sci override: global_irq=20 trigger=0 polarity=1
xen: registering gsi 20 triggering 0 polarity 1
xen: --> pirq=20 -> irq=20
xen: acpi sci 20
.. snip..
calling acpi_init+0x0/0xbc @ 1
ACPI: SCI (IRQ9) allocation failed
ACPI Exception: AE_NOT_ACQUIRED, Unable to install System Control Interrupt handler (20110413/evevent-119)
ACPI: Unable to start the ACPI Interpreter
as the ACPI interpreter made a call to 'acpi_gsi_to_irq' which got nine.
It used that value to request an IRQ (request_irq) and since that was not
present it failed.
The fix is to recognize that for interrupts that are overriden (in our
case we only care about the ACPI SCI) we should use the IRQ number
to present the IRQ instead of the using GSI. End result is that we get:
xen: sci override: global_irq=20 trigger=0 polarity=1
xen: registering gsi 20 triggering 0 polarity 1
xen: --> pirq=20 -> irq=9 (gsi=9)
xen: acpi sci 9
which fixes the ACPI interpreter failing on startup.
CC: stable@kernel.org
Reported-by: Liwei <xieliwei@gmail.com>
Tested-by: Liwei <xieliwei@gmail.com>
[http://lists.xensource.com/archives/html/xen-devel/2011-06/msg01727.html]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If we have CONFIG_XEN and the other parameters to build an
Linux kernel that is non-privileged, the xen_[find|register|unregister]_
device_domain_owner functions should not be compiled. They should
use the nops defined in arch/x86/include/asm/xen/pci.h instead.
This fixes:
arch/x86/pci/xen.c:496: error: redefinition of ‘xen_find_device_domain_owner’
arch/x86/include/asm/xen/pci.h:25: note: previous definition of ‘xen_find_device_domain_owner’ was here
arch/x86/pci/xen.c:510: error: redefinition of ‘xen_register_device_domain_owner’
arch/x86/include/asm/xen/pci.h:29: note: previous definition of ‘xen_register_device_domain_owner’ was here
arch/x86/pci/xen.c:532: error: redefinition of ‘xen_unregister_device_domain_owner’
arch/x86/include/asm/xen/pci.h:34: note: previous definition of ‘xen_unregister_device_domain_owner’ was here
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
We check if there is a domain owner for the PCI device. In case of failure
(meaning no domain has registered for this device) we make DOMID_SELF the owner.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: deal with rebasing on v2.6.37-1]
[v3: deal with rebasing on stable/irq.cleanup]
[v4: deal with rebasing on stable/irq.ween_of_nr_irqs]
[v5: deal with rebasing on v2.6.39-rc3]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Xiantao Zhang <xiantao.zhang@intel.com>
When the Xen PCI backend is told to enable or disable MSI/MSI-X functions,
the initial domain performs these operations. The initial domain needs
to know which domain (guest) is going to use the PCI device so when it
makes the appropiate hypercall to retrieve the MSI/MSI-X vector it will
also assign the PCI device to the appropiate domain (guest).
This boils down to us needing a mechanism to find, set and unset the domain
id that will be using the device.
[v2: EXPORT_SYMBOL -> EXPORT_SYMBOL_GPL.]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Following the example set by xen_allocate_pirq_msi and
xen_bind_pirq_msi_to_irq:
xen_allocate_pirq becomes xen_allocate_pirq_gsi and now only allocates
a pirq number and does not bind it.
xen_map_pirq_gsi becomes xen_bind_pirq_gsi_to_irq and binds an
existing pirq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The function name does not distinguish it from xen_allocate_pirq_msi
(which operates on domU and pvhvm domains rather than dom0).
Hoist domain 0 specific functionality up into the only caller leaving
functionality common to all guest types in xen_bind_pirq_msi_to_irq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Makes the tail end of this function look even more like
xen_bind_pirq_msi_to_irq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Split the binding aspect of xen_allocate_pirq_msi out into a new
xen_bind_pirq_to_irq function.
In xen_hvm_setup_msi_irq when allocating a pirq write the MSI message
to signal the PIRQ as soon as the pirq is obtained. There is no way to
free the pirq back so if the subsequent binding to an IRQ fails we
want to ensure that we will reuse the PIRQ next time rather than leak
it.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
apic_register_gsi_xen_hvm is a tiny wrapper around
xen_hvm_register_pirq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
consistent with other similar functions.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
