Allow the multipath target to avoid making small allocations for each
'struct dm_mpath_io' that is needed for each request.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Rename various methods to have either a "dm_old" or "dm_mq" prefix.
Improve code comments to assist with understanding the duality of code
that handles both "dm_old" and "dm_mq" cases.
It is no much easier to quickly look at the code and _know_ that a given
method is either 1) "dm_old" only 2) "dm_mq" only 3) common to both.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Remove all fiddley code that propped up this support for a blk-mq
request-queue ontop of all .request_fn devices.
Testing has proven this niche request-based dm-mq mode to be buggy, when
testing fault tolerance with DM multipath, and there is no point trying
to preserve it.
Should help improve efficiency of pure dm-mq code and make code
maintenance less delicate.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
DM multipath is the only dm-mq target. But that aside, request-based DM
only supports tables with a single target that is immutable. Leverage
this fact in dm_mq_queue_rq() by using the 'immutable_target' stored in
the mapped_device when the table was made active. This saves the need
to even take the read-side of the SRCU via dm_{get,put}_live_table.
If the active DM table does not have an immutable target (e.g. "error"
target was swapped in) then fallback to the slow-path where the target
is looked up from the live table.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In multipath_prepare_ioctl(),
- pgpath is a path selected from available paths
- m->queue_io is true if we cannot send a request immediately to
paths, either because:
* there is no available path
* the path group needs activation (pg_init)
- pg_init is not started
- pg_init is still running
- m->queue_if_no_path is true if the device is configured to queue
I/O if there are no available paths
If !pgpath && !m->queue_if_no_path, the handler should return -EIO.
However in the course of refactoring the condition check has broken
and returns success in that case. Since bdev points to the dm device
itself, dm_blk_ioctl() calls __blk_dev_driver_ioctl() for itself and
recurses until crash.
You could reproduce the problem like this:
# dmsetup create mp --table '0 1024 multipath 0 0 0 0'
# sg_inq /dev/mapper/mp
<crash>
[ 172.648615] BUG: unable to handle kernel paging request at fffffffc81b10268
[ 172.662843] PGD 19dd067 PUD 0
[ 172.666269] Thread overran stack, or stack corrupted
[ 172.671808] Oops: 0000 [#1] SMP
...
Fix the condition check with some clarifications.
Fixes: e56f81e0b0 ("dm: refactor ioctl handling")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm-mpath retries ioctl, when no path is readily available and the device
is configured to queue I/O in such a case. If you want to stop the retry
before multipathd decides to turn off queueing mode, you could send
signal for the process to exit from the loop.
However the check of fatal signal has not carried along when commit
6c182cd88d ("dm mpath: fix ioctl deadlock when no paths") moved the
loop from dm-mpath to dm core. As a result, we can't terminate such
a process in the retry loop.
Easy reproducer of the situation is:
# dmsetup create mp --table '0 1024 multipath 0 0 0 0'
# dmsetup message mp 0 'queue_if_no_path'
# sg_inq /dev/mapper/mp
then you should be able to terminate sg_inq by pressing Ctrl+C.
Fixes: 6c182cd88d ("dm mpath: fix ioctl deadlock when no paths")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
This adds support to pass through persistent reservation requests
similar to the existing ioctl handling, and with the same limitations,
e.g. devices may only have a single target attached.
This is mostly intended for multipathing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This moves the call to blkdev_ioctl and the argument checking to DM core
code, and only leaves a callout to find the block device to operate on
in the targets. This simplifies the code and allows us to pass through
ioctl-like command using other methods in the next patch.
Also split out a helper around calling the prepare_ioctl method that
will be reused for persistent reservation handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This reverts commit a1989b3300.
That commit introduced a regression at least for the case of the SG_IO ioctl()
running without CAP_SYS_RAWIO capability (e.g., unprivileged users) when there
are no active paths: the ioctl() fails with the ENOTTY errno immediately rather
than blocking due to queue_if_no_path until a path becomes active, for example.
That case happens to be exercised by QEMU KVM guests with 'scsi-block' devices
(qemu "-device scsi-block" [1], libvirt "<disk type='block' device='lun'>" [2])
from multipath devices; which leads to SCSI/filesystem errors in such a guest.
More general scenarios can hit that regression too. The following demonstration
employs a SG_IO ioctl() with a standard SCSI INQUIRY command for this objective
(some output & user changes omitted for brevity and comments added for clarity).
Reverting that commit restores normal operation (queueing) in failing scenarios;
tested on linux-next (next-20151022).
1) Test-case is based on sg_simple0 [3] (just SG_IO; remove SG_GET_VERSION_NUM)
$ cat sg_simple0.c
... see [3] ...
$ sed '/SG_GET_VERSION_NUM/,/}/d' sg_simple0.c > sgio_inquiry.c
$ gcc sgio_inquiry.c -o sgio_inquiry
2) The ioctl() works fine with active paths present.
# multipath -l 85ag56
85ag56 (...) dm-19 IBM ,2145
size=60G features='1 queue_if_no_path' hwhandler='0' wp=rw
|-+- policy='service-time 0' prio=0 status=active
| |- 8:0:11:0 sdz 65:144 active undef running
| `- 9:0:9:0 sdbf 67:144 active undef running
`-+- policy='service-time 0' prio=0 status=enabled
|- 8:0:12:0 sdae 65:224 active undef running
`- 9:0:12:0 sdbo 68:32 active undef running
$ ./sgio_inquiry /dev/mapper/85ag56
Some of the INQUIRY command's response:
IBM 2145 0000
INQUIRY duration=0 millisecs, resid=0
3) The ioctl() fails with ENOTTY errno with _no_ active paths present,
for unprivileged users (rather than blocking due to queue_if_no_path).
# for path in $(multipath -l 85ag56 | grep -o 'sd[a-z]\+'); \
do multipathd -k"fail path $path"; done
# multipath -l 85ag56
85ag56 (...) dm-19 IBM ,2145
size=60G features='1 queue_if_no_path' hwhandler='0' wp=rw
|-+- policy='service-time 0' prio=0 status=enabled
| |- 8:0:11:0 sdz 65:144 failed undef running
| `- 9:0:9:0 sdbf 67:144 failed undef running
`-+- policy='service-time 0' prio=0 status=enabled
|- 8:0:12:0 sdae 65:224 failed undef running
`- 9:0:12:0 sdbo 68:32 failed undef running
$ ./sgio_inquiry /dev/mapper/85ag56
sg_simple0: Inquiry SG_IO ioctl error: Inappropriate ioctl for device
4) dmesg shows that scsi_verify_blk_ioctl() failed for SG_IO (0x2285);
it returns -ENOIOCTLCMD, later replaced with -ENOTTY in vfs_ioctl().
$ dmesg
<...>
[] device-mapper: multipath: Failing path 65:144.
[] device-mapper: multipath: Failing path 67:144.
[] device-mapper: multipath: Failing path 65:224.
[] device-mapper: multipath: Failing path 68:32.
[] sgio_inquiry: sending ioctl 2285 to a partition!
5) The ioctl() only works if the SYS_CAP_RAWIO capability is present
(then queueing happens -- in this example, queue_if_no_path is set);
this is due to a conditional check in scsi_verify_blk_ioctl().
# capsh --drop=cap_sys_rawio -- -c './sgio_inquiry /dev/mapper/85ag56'
sg_simple0: Inquiry SG_IO ioctl error: Inappropriate ioctl for device
# ./sgio_inquiry /dev/mapper/85ag56 &
[1] 72830
# cat /proc/72830/stack
[<c00000171c0df700>] 0xc00000171c0df700
[<c000000000015934>] __switch_to+0x204/0x350
[<c000000000152d4c>] msleep+0x5c/0x80
[<c00000000077dfb0>] dm_blk_ioctl+0x70/0x170
[<c000000000487c40>] blkdev_ioctl+0x2b0/0x9b0
[<c0000000003128e4>] block_ioctl+0x64/0xd0
[<c0000000002dd3b0>] do_vfs_ioctl+0x490/0x780
[<c0000000002dd774>] SyS_ioctl+0xd4/0xf0
[<c000000000009358>] system_call+0x38/0xd0
6) This is the function call chain exercised in this analysis:
SYSCALL_DEFINE3(ioctl, <...>) @ fs/ioctl.c
-> do_vfs_ioctl()
-> vfs_ioctl()
...
error = filp->f_op->unlocked_ioctl(filp, cmd, arg);
...
-> dm_blk_ioctl() @ drivers/md/dm.c
-> multipath_ioctl() @ drivers/md/dm-mpath.c
...
(bdev = NULL, due to no active paths)
...
if (!bdev || <...>) {
int err = scsi_verify_blk_ioctl(NULL, cmd);
if (err)
r = err;
}
...
-> scsi_verify_blk_ioctl() @ block/scsi_ioctl.c
...
if (bd && bd == bd->bd_contains) // not taken (bd = NULL)
return 0;
...
if (capable(CAP_SYS_RAWIO)) // not taken (unprivileged user)
return 0;
...
printk_ratelimited(KERN_WARNING
"%s: sending ioctl %x to a partition!\n" <...>);
return -ENOIOCTLCMD;
<-
...
return r ? : <...>
<-
...
if (error == -ENOIOCTLCMD)
error = -ENOTTY;
out:
return error;
...
Links:
[1] http://git.qemu.org/?p=qemu.git;a=commit;h=336a6915bc7089fb20fea4ba99972ad9a97c5f52
[2] https://libvirt.org/formatdomain.html#elementsDisks (see 'disk' -> 'device')
[3] http://tldp.org/HOWTO/SCSI-Generic-HOWTO/pexample.html (Revision 1.2, 2002-05-03)
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
This way we can reused the same code any attachment method, not just those
requested from dm-mpath.
[jejb: fixup checkpatch error]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
While allowing dm-mpath to attach device handlers is a functionality we need
for backwards compatibility reason there is no reason to reference count
them and detach them if dm-mpath stops using the device for some reason.
If the device handler works for the given device it can just stay attached,
and we can take the retain_hw_handler codepath.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
dm_mq_queue_rq() is in atomic context so care must be taken to not
sleep -- as such GFP_ATOMIC is used for the md->bs bioset allocations
and dm-mpath's call to blk_get_request(). In the future the bioset
allocations will hopefully go away (by removing support for partial
completions of bios in a cloned request).
Also prepare for supporting DM blk-mq ontop of old-style request_fn
device(s) if a new dm-mod 'use_blk_mq' parameter is set. The kthread
will still be used to queue work if blk-mq is used ontop of old-style
request_fn device(s).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit e5863d9ad ("dm: allocate requests in target when stacking on
blk-mq devices") served as the first step toward fully utilizing blk-mq
in request-based DM -- it enabled stacking an old-style (request_fn)
request_queue ontop of the underlying blk-mq device(s). That first step
didn't improve performance of DM multipath ontop of fast blk-mq devices
(e.g. NVMe) because the top-level old-style request_queue was severely
limited by the queue_lock.
The second step offered here enables stacking a blk-mq request_queue
ontop of the underlying blk-mq device(s). This unlocks significant
performance gains on fast blk-mq devices, Keith Busch tested on his NVMe
testbed and offered this really positive news:
"Just providing a performance update. All my fio tests are getting
roughly equal performance whether accessed through the raw block
device or the multipath device mapper (~470k IOPS). I could only push
~20% of the raw iops through dm before this conversion, so this latest
tree is looking really solid from a performance standpoint."
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Tested-by: Keith Busch <keith.busch@intel.com>
Currently the cleanup of all error cases are open-coded. Introduce a
common exit path and labels.
Signed-off-by: Johannes Thumshirn <morbidrsa@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
For blk-mq request-based DM the responsibility of allocating a cloned
request is transfered from DM core to the target type. Doing so
enables the cloned request to be allocated from the appropriate
blk-mq request_queue's pool (only the DM target, e.g. multipath, can
know which block device to send a given cloned request to).
Care was taken to preserve compatibility with old-style block request
completion that requires request-based DM _not_ acquire the clone
request's queue lock in the completion path. As such, there are now 2
different request-based DM target_type interfaces:
1) the original .map_rq() interface will continue to be used for
non-blk-mq devices -- the preallocated clone request is passed in
from DM core.
2) a new .clone_and_map_rq() and .release_clone_rq() will be used for
blk-mq devices -- blk_get_request() and blk_put_request() are used
respectively from these hooks.
dm_table_set_type() was updated to detect if the request-based target is
being stacked on blk-mq devices, if so DM_TYPE_MQ_REQUEST_BASED is set.
DM core disallows switching the DM table's type after it is set. This
means that there is no mixing of non-blk-mq and blk-mq devices within
the same request-based DM table.
[This patch was started by Keith and later heavily modified by Mike]
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Switch to having request-based DM enqueue all prep'ed requests into work
processed by another thread. This allows request-based DM to invoke
block APIs that assume interrupt enabled context (e.g. blk_get_request)
and is a prerequisite for adding blk-mq support to request-based DM.
The new kernel thread is only initialized for request-based DM devices.
multipath_map() is now always in irq enabled context so change multipath
spinlock (m->lock) locking to always disable interrupts.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
'queue_io' is set so that IO is queued while paths are being
initialized. Clear queue_io in __choose_pgpath if there are no valid
paths, since there are obviously no paths that can be initialized.
Otherwise IOs to the device will back up.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
pg_ready() is not comprehensive in its logic and only serves to
obfuscate code. Replace pg_ready() with the appropriate logic in
multipath_map().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit e80991773 ("dm mpath: push back requests instead of queueing")
modified multipath_busy() to return true if !pg_ready(). pg_ready()
checks the current state of the multipath device and may return false
even if a new IO is needed to change the state.
Bart Van Assche reported that he had multipath IO lockup when he was
performing cable pull tests. Analysis showed that the multipath
device had a single path group with both paths active, but that the
path group itself was not active. During the multipath device state
transitions 'queue_io' got set but nothing could clear it. Clearing
'queue_io' only happens in __choose_pgpath(), but it won't be called
if multipath_busy() returns true due to pg_ready() returning false
when 'queue_io' is set.
As such the !pg_ready() check in multipath_busy() is wrong because new
IO will not be sent to multipath target and the multipath state change
won't happen. That results in multipath IO lockup.
The intent of multipath_busy() is to avoid unnecessary cycles of
dequeue + request_fn + requeue if it is known that the multipath
device will requeue.
Such "busy" situations would be:
- path group is being activated
- there is no path and the multipath is setup to requeue if no path
Fix multipath_busy() to return "busy" early only for these specific
situations.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.15
Add DM core support for disabling WRITE SAME on first failure to both
request-based and bio-based targets. The need to disable WRITE SAME
stems from SCSI enabling it by default but then disabling it when it
fails. When SCSI does this it returns "permanent target failure, do
not retry" using -EREMOTEIO. Update DM core to only disable WRITE SAME
on failure if the returned error is -EREMOTEIO.
Commit f84cb8a4 ("dm mpath: disable WRITE SAME if it fails")
implemented multipath specific disabling of WRITE SAME if it fails.
However, as that commit detailed, the multipath-only solution doesn't go
far enough if bio-based DM targets are stacked ontop of the
request-based dm-multipath target (as is commonly done using dm-linear
to support partitions on multipath devices, via kpartx).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Tested-by: Alex Chen <alex.chen@huawei.com>
lockdep complains about a circular locking. And indeed, we need to
release the lock before calling dm_table_run_md_queue_async().
As such, commit 4cdd2ad ("dm mpath: fix lock order inconsistency in
multipath_ioctl") must also be reverted in addition to fixing the
lock order in the other dm_table_run_md_queue_async() callers.
Reported-by: Bart van Assche <bvanassche@acm.org>
Tested-by: Bart van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit 3e9f1be1b4 ("dm mpath: remove process_queued_ios()") did not
consistently take the multipath device's spinlock (m->lock) before
calling dm_table_run_md_queue_async() -- which takes the q->queue_lock.
Found with code inspection using hint from reported lockdep warning.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The warning message "Unrecognised multipath message received" is
displayed in two different situations in multipath_message(): when the
number of arguments passed is invalid and when the string passed in
argv[0] is not recognized.
Make it easier to identify where the problem is by making these warnings
more specific with additional context for each case.
Signed-off-by: Jose Castillo <jcastillo@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
activate_path() is run without a lock, so the path might be
set to failed before activate_path() had a chance to run.
This patch add a check for ->active in activate_path() to
avoid unnecessary overhead by calling functions which are known
to be failing.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Return early for case when no path exists, and when the
pathgroup isn't ready. This eliminates the need for
extra nesting for the the common case.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
multipath_map() is now just a wrapper around map_io(), so we
can rename map_io() to multipath_map().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
When multipath needs to requeue I/O in the block layer the per-request
context shouldn't be allocated, as it will be freed immediately
afterwards anyway. Avoiding this memory allocation will reduce memory
pressure during requeuing.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
process_queued_ios() has served 3 functions:
1) select pg and pgpath if none is selected
2) start pg_init if requested
3) dispatch queued IOs when pg is ready
Basically, a call to queue_work(process_queued_ios) can be replaced by
dm_table_run_md_queue_async(), which runs request queue and ends up
calling map_io(), which does 1), 2) and 3).
Exception is when !pg_ready() (which means either pg_init is running or
requested), then multipath_busy() prevents map_io() being called from
request_fn.
If pg_init is running, it should be ok as long as pg_init_done() does
the right thing when pg_init is completed, I.e.: restart pg_init if
!pg_ready() or call dm_table_run_md_queue_async() to kick map_io().
If pg_init is requested, we have to make sure the request is detected
and pg_init will be started. pg_init is requested in 3 places:
a) __choose_pgpath() in map_io()
b) __choose_pgpath() in multipath_ioctl()
c) pg_init retry in pg_init_done()
a) is ok because map_io() calls __pg_init_all_paths(), which does 2).
b) needs a call to __pg_init_all_paths(), which does 2).
c) needs a call to __pg_init_all_paths(), which does 2).
So this patch removes process_queued_ios() and ensures that
__pg_init_all_paths() is called at the appropriate locations.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
There is no reason why multipath needs to queue requests internally for
queue_if_no_path or pg_init; we should rather push them back onto the
request queue.
And while we're at it we can simplify the conditional statement in
map_io() to make it easier to read.
Since mpath no longer does internal queuing of I/O the table info no
longer emits the internal queue_size. Instead it displays 1 if queuing
is being used or 0 if it is not.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
This patch moves condition checks as a preparation of following
patches and has no effect on behaviour.
process_queued_ios() is the only caller of __pg_init_all_paths()
and 2 condition checks are moved from outside to inside without
side effects.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
An invalid ioctl will never be valid, irrespective of whether multipath
has active paths or not. So for invalid ioctls we do not have to wait
for multipath to activate any paths, but can rather return an error
code immediately. This fix resolves numerous instances of:
udevd[]: worker [] unexpectedly returned with status 0x0100
that have been seen during testing.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
When pg_init is running no I/O can be submitted to the underlying
devices, as the path priority etc might change. When using queue_io for
this, requests will be piling up within multipath as the block I/O
scheduler just sees a _very fast_ device. All of this queued I/O has to
be resubmitted from within multipathing once pg_init is done.
This approach has the problem that it's virtually impossible to
abort I/O when pg_init is running, and we're adding heavy load
to the devices after pg_init since all of the queued I/O needs to be
resubmitted _before_ any requests can be pulled off of the request queue
and normal operation continues.
This patch will requeue the I/O that triggers the pg_init call, and
return 'busy' when pg_init is in progress. With these changes the block
I/O scheduler will stop submitting I/O during pg_init, resulting in a
quicker path switch and less I/O pressure (and memory consumption) after
pg_init.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[patch header edited for clarity and typos by Mike Snitzer]
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Whenever multipath_dtr() is happening we must prevent queueing any
further path activation work. Implement this by adding a new
'pg_init_disabled' flag to the multipath structure that denotes future
path activation work should be skipped if it is set. By disabling
pg_init and then re-enabling in flush_multipath_work() we also avoid the
potential for pg_init to be initiated while suspending an mpath device.
Without this patch a race condition exists that may result in a kernel
panic:
1) If after pg_init_done() decrements pg_init_in_progress to 0, a call
to wait_for_pg_init_completion() assumes there are no more pending path
management commands.
2) If pg_init_required is set by pg_init_done(), due to retryable
mode_select errors, then process_queued_ios() will again queue the
path activation work.
3) If free_multipath() completes before activate_path() work is called a
NULL pointer dereference like the following can be seen when
accessing members of the recently destructed multipath:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000090
RIP: 0010:[<ffffffffa003db1b>] [<ffffffffa003db1b>] activate_path+0x1b/0x30 [dm_multipath]
[<ffffffff81090ac0>] worker_thread+0x170/0x2a0
[<ffffffff81096c80>] ? autoremove_wake_function+0x0/0x40
[switch to disabling pg_init in flush_multipath_work & header edits by Mike Snitzer]
Signed-off-by: Shiva Krishna Merla <shivakrishna.merla@netapp.com>
Reviewed-by: Krishnasamy Somasundaram <somasundaram.krishnasamy@netapp.com>
Tested-by: Speagle Andy <Andy.Speagle@netapp.com>
Acked-by: Junichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Allow user to change the number of IOs that are reserved by
request-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_rq_based_ios
The default value is RESERVED_REQUEST_BASED_IOS (256). The maximum
allowed value is RESERVED_MAX_IOS (1024).
Export dm_get_reserved_rq_based_ios() for use by DM targets and core
code. Switch to sizing dm-mpath's mempool using DM core's configurable
'reserved_rq_based_ios'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Workaround the SCSI layer's problematic WRITE SAME heuristics by
disabling WRITE SAME in the DM multipath device's queue_limits if an
underlying device disabled it.
The WRITE SAME heuristics, with both the original commit 5db44863b6
("[SCSI] sd: Implement support for WRITE SAME") and the updated commit
66c28f971 ("[SCSI] sd: Update WRITE SAME heuristics"), default to enabling
WRITE SAME(10) even without successfully determining it is supported.
After the first failed WRITE SAME the SCSI layer will disable WRITE SAME
for the device (by setting sdkp->device->no_write_same which results in
'max_write_same_sectors' in device's queue_limits to be set to 0).
When a device is stacked ontop of such a SCSI device any changes to that
SCSI device's queue_limits do not automatically propagate up the stack.
As such, a DM multipath device will not have its WRITE SAME support
disabled. This causes the block layer to continue to issue WRITE SAME
requests to the mpath device which causes paths to fail and (if mpath IO
isn't configured to queue when no paths are available) it will result in
actual IO errors to the upper layers.
This fix doesn't help configurations that have additional devices
stacked ontop of the mpath device (e.g. LVM created linear DM devices
ontop). A proper fix that restacks all the queue_limits from the bottom
of the device stack up will need to be explored if SCSI will continue to
use this model of optimistically allowing op codes and then disabling
them after they fail for the first time.
Before this patch:
EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
device-mapper: multipath: XXX snitm debugging: got -EREMOTEIO (-121)
device-mapper: multipath: XXX snitm debugging: failing WRITE SAME IO with error=-121
end_request: critical target error, dev dm-6, sector 528
dm-6: WRITE SAME failed. Manually zeroing.
device-mapper: multipath: Failing path 8:112.
end_request: I/O error, dev dm-6, sector 4616
dm-6: WRITE SAME failed. Manually zeroing.
end_request: I/O error, dev dm-6, sector 4616
end_request: I/O error, dev dm-6, sector 5640
end_request: I/O error, dev dm-6, sector 6664
end_request: I/O error, dev dm-6, sector 7688
end_request: I/O error, dev dm-6, sector 524288
Buffer I/O error on device dm-6, logical block 65536
lost page write due to I/O error on dm-6
JBD2: Error -5 detected when updating journal superblock for dm-6-8.
end_request: I/O error, dev dm-6, sector 524296
Aborting journal on device dm-6-8.
end_request: I/O error, dev dm-6, sector 524288
Buffer I/O error on device dm-6, logical block 65536
lost page write due to I/O error on dm-6
JBD2: Error -5 detected when updating journal superblock for dm-6-8.
# cat /sys/block/sdh/queue/write_same_max_bytes
0
# cat /sys/block/dm-6/queue/write_same_max_bytes
33553920
After this patch:
EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
device-mapper: multipath: XXX snitm debugging: got -EREMOTEIO (-121)
device-mapper: multipath: XXX snitm debugging: WRITE SAME I/O failed with error=-121
end_request: critical target error, dev dm-6, sector 528
dm-6: WRITE SAME failed. Manually zeroing.
# cat /sys/block/sdh/queue/write_same_max_bytes
0
# cat /sys/block/dm-6/queue/write_same_max_bytes
0
It should be noted that WRITE SAME support wasn't enabled in DM
multipath until v3.10.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org # 3.10+
Since ENOSPC is a target-side error, dm-mpath should just pass the error
information to upper layer instead of retrying itself with path failover.
Otherwise it will end up failing all paths down while path checkers find
all paths ok.
ENOSPC can now be returned from SCSI device after commit a9d6ceb8
("[SCSI] return ENOSPC on thin provisioning failure").
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When a medium error is detected the SCSI stack should return
ENODATA to the upper layers.
[jejb: fix whitespace error]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When multipath needs to retry an ioctl the reference to the
current live table needs to be dropped. Otherwise a deadlock
occurs when all paths are down:
- dm_blk_ioctl takes a reference to the current table
and spins in multipath_ioctl().
- A new table is being loaded, but upon resume the process
hangs in dm_table_destroy() waiting for references to
drop to zero.
With this patch the reference to the old table is dropped
prior to retry, thereby avoiding the deadlock.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Enable WRITE SAME support in dm multipath. As far as multipath is
concerned it is just another write request.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Tested-by: Bharata B Rao <bharata.rao@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use 'bio' in the name of variables and functions that deal with
bios rather than 'request' to avoid confusion with the normal
block layer use of 'request'.
No functional changes.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Avoid returning a truncated table or status string instead of setting
the DM_BUFFER_FULL_FLAG when the last target of a table fills the
buffer.
When processing a table or status request, the function retrieve_status
calls ti->type->status. If ti->type->status returns non-zero,
retrieve_status assumes that the buffer overflowed and sets
DM_BUFFER_FULL_FLAG.
However, targets don't return non-zero values from their status method
on overflow. Most targets returns always zero.
If a buffer overflow happens in a target that is not the last in the
table, it gets noticed during the next iteration of the loop in
retrieve_status; but if a buffer overflow happens in the last target, it
goes unnoticed and erroneously truncated data is returned.
In the current code, the targets behave in the following way:
* dm-crypt returns -ENOMEM if there is not enough space to store the
key, but it returns 0 on all other overflows.
* dm-thin returns errors from the status method if a disk error happened.
This is incorrect because retrieve_status doesn't check the error
code, it assumes that all non-zero values mean buffer overflow.
* all the other targets always return 0.
This patch changes the ti->type->status function to return void (because
most targets don't use the return code). Overflow is detected in
retrieve_status: if the status method fills up the remaining space
completely, it is assumed that buffer overflow happened.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The mpio dereference should be moved below the BUG_ON NULL test
in multipath_end_io().
spatch with a semantic match was used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
When there are no paths and multipath receives an ioctl, it waits until
a path becomes available. This behaviour is incorrect if the
"queue_if_no_path" setting was not specified, as then the ioctl should
be rejected immediately, which this patch now does.
commit 35991652b ("dm mpath: allow ioctls to trigger pg init") should
have checked if queue_if_no_path was configured before queueing IO.
Checking for the queue_if_no_path feature, like is done in map_io(),
allows the following table load to work without blocking in the
multipath_ioctl retry loop:
echo "0 1024 multipath 0 0 0 0" | dmsetup create mpath_nodevs
Without this fix the multipath_ioctl will block with the following stack
trace:
blkid D 0000000000000002 0 23936 1 0x00000000
ffff8802b89e5cd8 0000000000000082 ffff8802b89e5fd8 0000000000012440
ffff8802b89e4010 0000000000012440 0000000000012440 0000000000012440
ffff8802b89e5fd8 0000000000012440 ffff88030c2aab30 ffff880325794040
Call Trace:
[<ffffffff814ce099>] schedule+0x29/0x70
[<ffffffff814cc312>] schedule_timeout+0x182/0x2e0
[<ffffffff8104dee0>] ? lock_timer_base+0x70/0x70
[<ffffffff814cc48e>] schedule_timeout_uninterruptible+0x1e/0x20
[<ffffffff8104f840>] msleep+0x20/0x30
[<ffffffffa0000839>] multipath_ioctl+0x109/0x170 [dm_multipath]
[<ffffffffa06bfb9c>] dm_blk_ioctl+0xbc/0xd0 [dm_mod]
[<ffffffff8122a408>] __blkdev_driver_ioctl+0x28/0x30
[<ffffffff8122a79e>] blkdev_ioctl+0xce/0x730
[<ffffffff811970ac>] block_ioctl+0x3c/0x40
[<ffffffff8117321c>] do_vfs_ioctl+0x8c/0x340
[<ffffffff81166293>] ? sys_newfstat+0x33/0x40
[<ffffffff81173571>] sys_ioctl+0xa1/0xb0
[<ffffffff814d70a9>] system_call_fastpath+0x16/0x1b
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.5+
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
Commit outstanding metadata before returning the status for a dm thin
pool so that the numbers reported are as up-to-date as possible.
The commit is not performed if the device is suspended or if
the DM_NOFLUSH_FLAG is supplied by userspace and passed to the target
through a new 'status_flags' parameter in the target's dm_status_fn.
The userspace dmsetup tool will support the --noflush flag with the
'dmsetup status' and 'dmsetup wait' commands from version 1.02.76
onwards.
Tested-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
A SCSI device handler might get attached to a device during the
initial device scan. We do not necessarily want to override
this when loading a multipath table, so this patch adds a new
multipath feature argument "retain_attached_hw_handler".
During SCSI device scan all loaded SCSI device handlers will be
consulted for a match (via scsi_dh's provided .match). If a match is
found that device handler will be attached. We need a way to have
userspace multipathd's provided 'hw_handler' not override the already
attached hardware handler.
When specifying the new feature 'retain_attached_hw_handler' multipath
will use the currently attached hardware handler instead of trying to
attach the one specified during table load. If no hardware handler is
attached the specified hardware handler will still be used.
Leverages scsi_dh_attach's ability to increment the scsi_dh's reference
count if the same scsi_dh name is provided when attaching - currently
attached scsi_dh name is determined with scsi_dh_attached_handler_name.
Depends upon commit 7e8a74b177
("[SCSI] scsi_dh: add scsi_dh_attached_handler_name").
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Tested-by: Babu Moger <babu.moger@netapp.com>
Reviewed-by: Chandra Seetharaman <sekharan@us.ibm.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device. Until this has happened, ioctls return -EAGAIN.
With this patch, new paths are made available in response to an ioctl
too. The processing of the ioctl gets delayed until this has happened.
Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.
Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure. Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands). For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too. It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If I/O needs retrying and only bypassed priority groups are available,
set the pg_init_delay_retry flag to wait before retrying.
If, for example, the reason for the bypass is that the controller is
getting reset or there is a firmware upgrade happening, retrying right
away would cause a flood of log messages and retries for what could be a
few seconds or even several minutes.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move multipath structure's 'lock' and 'queue_size' members to eliminate
two 4-byte holes. Also use a bit within a single unsigned int for each
existing flag (saves 8-bytes). This allows future flags to be added
without each consuming an unsigned int.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If the requested scsi_dh module is already loaded then skip
request_module().
Multipath table loads can hang in an unnecessary __request_module.
Reported-by: Ben Marzinski <bmarzins@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Device mapper uses sscanf to convert arguments to numbers. The problem is that
the way we use it ignores additional unmatched characters in the scanned string.
For example, this `if (sscanf(string, "%d", &number) == 1)' will match a number,
but also it will match number with some garbage appended, like "123abc".
As a result, device mapper accepts garbage after some numbers. For example
the command `dmsetup create vg1-new --table "0 16384 linear 254:1bla 34816bla"'
will pass without an error.
This patch fixes all sscanf uses in device mapper. It appends "%c" with
a pointer to a dummy character variable to every sscanf statement.
The construct `if (sscanf(string, "%d%c", &number, &dummy) == 1)' succeeds
only if string is a null-terminated number (optionally preceded by some
whitespace characters). If there is some character appended after the number,
sscanf matches "%c", writes the character to the dummy variable and returns 2.
We check the return value for 1 and consequently reject numbers with some
garbage appended.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The map_context pointer should always be set. However, we have reports
that upon requeuing it is not set correctly. So add set and clear
functions with a BUG_ON() to track the issue properly.
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
A logical volume can map to just part of underlying physical volume.
In this case, it must be treated like a partition.
Based on a patch from Alasdair G Kergon.
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move multipath target argument parsing code into dm-table so other
targets can share it.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Avoid dereferencing a NULL pointer if the number of feature arguments
supplied is fewer than indicated.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: stable@kernel.org
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Integrity errors need to be passed to the owner of the integrity
metadata for processing. Consequently EILSEQ should be passed up the
stack.
Cc: stable@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adjusts the multipath target to allow a table with both 0
priority groups and 0 for the initial priority group number.
If any mpath device is held open when all paths in the last priority
group have failed, userspace multipathd will attempt to reload the
associated DM table to reflect the fact that the device no longer has
any priority groups. But the reload attempt always failed because the
multipath target did not allow 0 priority groups.
All multipath target messages related to priority group (enable_group,
disable_group, switch_group) will handle a priority group of 0 (will
cause error).
When reloading a multipath table with 0 priority groups, userspace
multipathd must be updated to specify an initial priority group number
of 0 (rather than 1).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Babu Moger <babu.moger@lsi.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fail the reinstate_path and fail_path message ioctl if the specified
path is not valid.
The message ioctl would succeed for the 'reinistate_path' and
'fail_path' messages even if action was not taken because the
specified device was not a valid path of the multipath device.
Before, when /dev/vdb is not a path of mpathb:
$ dmsetup message mpathb 0 reinstate_path /dev/vdb
$ echo $?
0
After:
$ dmsetup message mpathb 0 reinstate_path /dev/vdb
device-mapper: message ioctl failed: Invalid argument
Command failed
$ echo $?
1
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
DM now has more information about the nature of the underlying storage
failure. Path failure is avoided if a request failed due to a target
error. Instead the target error is immediately passed up the stack.
Discard requests that fail due to non-target errors may now be retried.
Errors restricted to the path will be retried or returned if no
paths are available, irregarding the no_path_retry setting.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds a user-configurable 'pg_init_delay_msecs' feature. Use
this feature to specify the number of milliseconds to delay before
retrying scsi_dh_activate, when SCSI_DH_RETRY is returned.
SCSI Device Handlers return SCSI_DH_IMM_RETRY if we could retry
activation immediately and SCSI_DH_RETRY in cases where it is better to
retry after some delay.
Currently we immediately retry scsi_dh_activate irrespective of
SCSI_DH_IMM_RETRY and SCSI_DH_RETRY.
The 'pg_init_delay_msecs' feature may be provided during table create or
load, e.g.:
dmsetup create --table "0 20971520 multipath 3 queue_if_no_path \
pg_init_delay_msecs 2500 ..." mpatha
The default for 'pg_init_delay_msecs' is 2000 milliseconds.
Maximum configurable delay is 60000 milliseconds. Specifying a
'pg_init_delay_msecs' of 0 will cause immediate retry.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Convert all create[_singlethread]_work() users to the new
alloc[_ordered]_workqueue(). This conversion is mechanical and
doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
flush_scheduled_work() is being deprecated. Flush the used work
directly instead. In all dm targets, the only work which uses
system_wq is ->trigger_event.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Revert commit 224cb3e981
dm: Call blk_abort_queue on failed paths
Multipath began to use blk_abort_queue() to allow for
lower latency path deactivation. This was found to
cause list corruption:
the cmd gets blk_abort_queued/timedout run on it and the scsi eh
somehow is able to complete and run scsi_queue_insert while
scsi_request_fn is still trying to process the request.
https://www.redhat.com/archives/dm-devel/2010-November/msg00085.html
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@kernel.org
Enable discard support in the DM multipath target.
This discard support depends on a few discard-specific fixes to the
block layer's request stacking driver methods.
Discard requests are optional so don't allow a failed discard to trigger
path failures. If there is a real problem with a given path the
barriers associated with the discard (either before or after the
discard) will cause path failure. That said, unconditionally passing
discard failures up the stack is not ideal. This must be fixed once DM
has more information about the nature of the underlying storage failure.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
multipath_ctr() forgets to return an error after detecting
missing path parameters. Fix this.
Signed-off-by: Patrick LoPresti <lopresti@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove unused parameters(start and len) of dm_get_device()
and fix the callers.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch pulls the pg_init path activation code out of
process_queued_ios() into a new function.
No functional change.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When suspending the device we must wait for all I/O to complete, but
pg-init may be still in progress even after flushing the workqueue
for kmpath_handlerd in multipath_postsuspend.
This patch waits for pg-init completion correctly in
multipath_postsuspend().
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
m->queue_io is set to block processing I/Os, and it needs to be kept
while pg-init, which issues multiple path activations, is in progress.
But m->queue is cleared when a path activation completes without error
in pg_init_done(), even while other path activations are in progress.
That may cause undesired -EIO on paths which are not complete activation.
This patch fixes that by not clearing m->queue_io until all path
activations complete.
(Before the hardware handlers were moved into the SCSI layer, pg_init
only used one path.)
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
'suspended' flag in struct multipath was introduced to check whether
the multipath target is in suspended state, but the same check is
done through dm_suspended() now, so remove the flag and related code.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds two minor fixes while processing device mapper path activation.
Skip failed paths while calling activate_path. If the path is already failed
then activate_path will fail for sure. We don't have to call in that case. In
some case this might cause prolonged retries unnecessarily.
Change the misleading message if the path being activated fails with SCSI_DH_NOSYS.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch removes some unnecessary argument casting. There is no
functional change with this patch.
Passes 'struct pgpath' through to pg_init_done() instead of the enclosed
'struct dm_path'.
Tested the changes with LSI storage..
CC: Chandra Seetharaman <chandra.seetharaman@us.ibm.com>
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch rejects messages that can generate I/O while the device
itself is suspended.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reject messages that can generate I/O while the device itself
is suspended.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a mutex to allow possible creators of new work to synchronize with
flushing work queues.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Acked-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch stops the remaining dm-mpath activity during the suspend
sequence by flushing workqueues in postsuspend function.
The current dm-mpath target may not be quiet even after suspend completes
because some workqueues (e.g. device_handler's work, event handling)
are not flushed during the suspend sequence, even though suspended
devices/targets are supposed to be quiet in this state.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Make scsi_dh_activate() function asynchronous, by taking in two additional
parameters, one is the callback function and the other is the data to call
the callback function with.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use scsi_dh_set_params() set parameters provided. Save the parameters in
parse_hw_handler() and use it in parse_path().
Reported-by: Eddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Tested-by: Eddie Williams <Eddie.Williams@steeleye.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Incorrect device area lengths are being passed to device_area_is_valid().
The regression appeared in 2.6.31-rc1 through commit
754c5fc7eb.
With the dm-stripe target, the size of the target (ti->len) was used
instead of the stripe_width (ti->len/#stripes). An example of a
consequent incorrect error message is:
device-mapper: table: 254:0: sdb too small for target
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch converts dm-multipath target to request-based from bio-based.
Basically, the patch just converts the I/O unit from struct bio
to struct request.
In the course of the conversion, it also changes the I/O queueing
mechanism. The change in the I/O queueing is described in details
as follows.
I/O queueing mechanism change
-----------------------------
In I/O submission, map_io(), there is no mechanism change from
bio-based, since the clone request is ready for retry as it is.
However, in I/O complition, do_end_io(), there is a mechanism change
from bio-based, since the clone request is not ready for retry.
In do_end_io() of bio-based, the clone bio has all needed memory
for resubmission. So the target driver can queue it and resubmit
it later without memory allocations.
The mechanism has almost no overhead.
On the other hand, in do_end_io() of request-based, the clone request
doesn't have clone bios, so the target driver can't resubmit it
as it is. To resubmit the clone request, memory allocation for
clone bios is needed, and it takes some overheads.
To avoid the overheads just for queueing, the target driver doesn't
queue the clone request inside itself.
Instead, the target driver asks dm core for queueing and remapping
the original request of the clone request, since the overhead for
queueing is just a freeing memory for the clone request.
As a result, the target driver doesn't need to record/restore
the information of the original request for resubmitting
the clone request. So dm_bio_details in dm_mpath_io is removed.
multipath_busy()
---------------------
The target driver returns "busy", only when the following case:
o The target driver will map I/Os, if map() function is called
and
o The mapped I/Os will wait on underlying device's queue due to
their congestions, if map() function is called now.
In other cases, the target driver doesn't return "busy".
Otherwise, dm core will keep the I/Os and the target driver can't
do what it wants.
(e.g. the target driver can't map I/Os now, so wants to kill I/Os.)
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add .iterate_devices to 'struct target_type' to allow a function to be
called for all devices in a DM target. Implemented it for all targets
except those in dm-snap.c (origin and snapshot).
(The raid1 version number jumps to 1.12 because we originally reserved
1.1 to 1.11 for 'block_on_error' but ended up using 'handle_errors'
instead.)
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: martin.petersen@oracle.com
This patch makes two additions to the dm path selector interface for
dynamic load balancers:
o a new hook, start_io()
o a new parameter 'nr_bytes' to select_path()/start_io()/end_io()
to pass the size of the I/O
start_io() is called when a target driver actually submits I/O
to the selected path.
Path selectors can use it to start accounting of the I/O.
(e.g. counting the number of in-flight I/Os.)
The start_io hook is based on the patch posted by Stefan Bader:
https://www.redhat.com/archives/dm-devel/2005-October/msg00050.html
nr_bytes, the size of the I/O, is so path selectors can take the
size of the I/O into account when deciding which path to use.
dm-service-time uses it to estimate service time, for example.
(Added the nr_bytes member to dm_mpath_io instead of using existing
details.bi_size, since request-based dm patch deletes it.)
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The commit fe9cf30eb8 moves dm table event
submission from kmultipath queue to kernel kevent queue to avoid a
deadlock.
There is a possibility of race condition because kevent queue is not flushed
in the multipath destructor. The scenario is:
- some event happens and is queued to keventd
- keventd thread is delayed due to scheuling latency or some other work
- multipath device is destroyed
- keventd now attempts to process work_struct that is residing in already
released memory.
The patch flushes the keventd queue in multipath constructor.
I've already fixed similar bug in dm-raid1.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: stable@kernel.org
Fixed a problem affecting reinstatement of passive paths.
Before we moved the hardware handler from dm to SCSI, it performed a pg_init
for a path group and didn't maintain any state about each path in hardware
handler code.
But in SCSI dh, such state is now maintained, as we want to fail I/O early on a
path if it is not the active path.
All the hardware handlers have a state now and set to active or some form of
inactive. They have prep_fn() which uses this state to fail the I/O without
it ever being sent to the device.
So in effect when dm-multipath calls scsi_dh_activate(), activate is
sent to only one path and the "state" of that path is changed appropriately
to "active" while other paths in the same path group are never changed
as they never got an "activate".
In order make sure all the paths in a path group gets their state set
properly when a pg_init happens, we need to call scsi_dh_activate() on
all paths in a path group.
Doing this at the hardware handler layer is not a good option as we
want the multipath layer to define the relationship between path and path
groups and not the hardware handler.
Attached patch sends an "activate" on each path in a path group when a
path group is switched. It also sends an activate when a path is reinstated.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When specifying a different hardware handler via multipath
features we should be able to override the built-in defaults.
The problem here is the hardware table from scsi_dh is compiled
in and cannot be changed from userland. The multipath.conf OTOH
is purely user-defined and, what's more, the user might have a valid
reason for modifying it.
(EG EMC Clariion can well be run in PNR mode even though ALUA is
active, or the user might want to try ALUA on any as-of-yet unknown
devices)
So _not_ allowing multipath to override the device handler setting
will just add to the confusion and makes error tracking even more
difficult.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
It's used by DM and MD and generally useful, so move the bio list
helpers into bio.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The same workqueue is used both for sending uevents and processing queued I/O.
Deadlock has been reported in RHEL5 when sending a uevent was blocked waiting
for the queued I/O to be processed. Use scheduled_work() for the asynchronous
uevents instead.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change dm_unregister_target to return void and use BUG() for error
reporting.
dm_unregister_target can only fail because of programming bug in the
target driver. It can't fail because of user's behavior or disk errors.
This patch changes unregister_target to return void and use BUG if
someone tries to unregister non-registered target or unregister target
that is in use.
This patch removes code duplication (testing of error codes in all dm
targets) and reports bugs in just one place, in dm_unregister_target. In
some target drivers, these return codes were ignored, which could lead
to a situation where bugs could be missed.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Currently dm ignores the parameters provided to hardware handlers
without providing any notifications to the user.
This patch just prints a warning message so that the user knows that
the arguments are ignored.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Path activation code is called even when the pgpath is NULL. This could
lead to a panic in activate_path(). Such a panic is seen in -rt kernel.
This problem has been there before the pg_init() was moved to a
workqueue.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/viro/bdev: (66 commits)
[PATCH] kill the rest of struct file propagation in block ioctls
[PATCH] get rid of struct file use in blkdev_ioctl() BLKBSZSET
[PATCH] get rid of blkdev_locked_ioctl()
[PATCH] get rid of blkdev_driver_ioctl()
[PATCH] sanitize blkdev_get() and friends
[PATCH] remember mode of reiserfs journal
[PATCH] propagate mode through swsusp_close()
[PATCH] propagate mode through open_bdev_excl/close_bdev_excl
[PATCH] pass fmode_t to blkdev_put()
[PATCH] kill the unused bsize on the send side of /dev/loop
[PATCH] trim file propagation in block/compat_ioctl.c
[PATCH] end of methods switch: remove the old ones
[PATCH] switch sr
[PATCH] switch sd
[PATCH] switch ide-scsi
[PATCH] switch tape_block
[PATCH] switch dcssblk
[PATCH] switch dasd
[PATCH] switch mtd_blkdevs
[PATCH] switch mmc
...
Change #include "dm.h" to #include <linux/device-mapper.h> in all targets.
Targets should not need direct access to internal DM structures.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
