Demonstrating the issue:
.. add a drop action
$sudo $TC actions add action drop index 10
.. retrieve it
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 2 bind 0 installed 29 sec used 29 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
... bug 1 above: reference is two.
Reference is actually 1 but we forget to subtract 1.
... do a GET again and we see the same issue
try a few times and nothing changes
~$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 2 bind 0 installed 31 sec used 31 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
... lets try to bind the action to a filter..
$ sudo $TC qdisc add dev lo ingress
$ sudo $TC filter add dev lo parent ffff: protocol ip prio 1 \
u32 match ip dst 127.0.0.1/32 flowid 1:1 action gact index 10
... and now a few GETs:
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 3 bind 1 installed 204 sec used 204 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 4 bind 1 installed 206 sec used 206 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 5 bind 1 installed 235 sec used 235 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
.... as can be observed the reference count keeps going up.
After the fix
$ sudo $TC actions add action drop index 10
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 1 bind 0 installed 4 sec used 4 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 1 bind 0 installed 6 sec used 6 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
$ sudo $TC qdisc add dev lo ingress
$ sudo $TC filter add dev lo parent ffff: protocol ip prio 1 \
u32 match ip dst 127.0.0.1/32 flowid 1:1 action gact index 10
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 2 bind 1 installed 32 sec used 32 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
$ sudo $TC -s actions get action gact index 10
action order 1: gact action drop
random type none pass val 0
index 10 ref 2 bind 1 installed 33 sec used 33 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Fixes: aecc5cefc3 ("net sched actions: fix GETing actions")
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory hotplug is leading to hash page table calls, even on radix:
arch_add_memory
create_section_mapping
htab_bolt_mapping
BUG_ON(!ppc_md.hpte_insert);
To fix, refactor {create,remove}_section_mapping() into hash__ and
radix__ variants. Leave the radix versions stubbed for now.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Reza Arbab <arbab@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The parameter name should be wwpn instead of wwnn.
Signed-off-by: Fam Zheng <famz@redhat.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bugfixes:
- Fix invalid fget()/fput() calls when doing file locking
- Fix multiple directory cache invalidation issues due to the client failing
to recognise that the directory wasn't changed.
- Fix client recovery when server reboots multiple times
-----BEGIN PGP SIGNATURE-----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=K8F7
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- fix invalid fget()/fput() calls when doing file locking
- fix multiple directory cache invalidation issues due to the client
failing to recognise that the directory wasn't changed
- fix client recovery when server reboots multiple times
* tag 'nfs-for-4.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix client recovery when server reboots multiple times
NFSv4: update_changeattr should update the attribute timestamp
NFSv4: Don't call update_changeattr() unless the unlink is successful
NFSv4: Don't apply change_info4 twice on rename within a directory
NFSv4: Call update_changeattr() from _nfs4_proc_open only if a file was created
nfs: Don't take a reference on fl->fl_file for LOCK operation
Tariq Toukan says:
====================
mlx4 core fixes
This patchset contains bug fixes from Jack to the mlx4 Core driver.
Patch 1 solves a race in the flow of CQ free.
Patch 2 moves some qp context flags update to the correct qp transition.
Patch 3 eliminates warnings from the path of SRQ_LIMIT that flood the message log,
and keeps them only in the path of SRQ_CATAS_ERROR.
Series generated against net commit:
1a717fcf8b Merge tag 'mac80211-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When running SRIOV, warnings for SRQ LIMIT events flood the Hypervisor's
message log when (correct, normally operating) apps use SRQ LIMIT events
as a trigger to post WQEs to SRQs.
Add more information to the existing debug printout for SRQ_LIMIT, and
output the warning messages only for the SRQ CATAS ERROR event.
Fixes: acba2420f9 ("mlx4_core: Add wrapper functions and comm channel and slave event support to EQs")
Fixes: e0debf9cb5 ("mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save the qp context flags byte containing the flag disabling vlan stripping
in the RESET to INIT qp transition, rather than in the INIT to RTR
transition. Per the firmware spec, the flags in this byte are active
in the RESET to INIT transition.
As a result of saving the flags in the incorrect qp transition, when
switching dynamically from VGT to VST and back to VGT, the vlan
remained stripped (as is required for VST) and did not return to
not-stripped (as is required for VGT).
Fixes: f0f829bf42 ("net/mlx4_core: Add immediate activate for VGT->VST->VGT")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function mlx4_cq_completion() and mlx4_cq_event(), the
radix_tree_lookup requires a rcu_read_lock.
This is mandatory: if another core frees the CQ, it could
run the radix_tree_node_rcu_free() call_rcu() callback while
its being used by the radix tree lookup function.
Additionally, in function mlx4_cq_event(), since we are adding
the rcu lock around the radix-tree lookup, we no longer need to take
the spinlock. Also, the synchronize_irq() call for the async event
eliminates the need for incrementing the cq reference count in
mlx4_cq_event().
Other changes:
1. In function mlx4_cq_free(), replace spin_lock_irq with spin_lock:
we no longer take this spinlock in the interrupt context.
The spinlock here, therefore, simply protects against different
threads simultaneously invoking mlx4_cq_free() for different cq's.
2. In function mlx4_cq_free(), we move the radix tree delete to before
the synchronize_irq() calls. This guarantees that we will not
access this cq during any subsequent interrupts, and therefore can
safely free the CQ after the synchronize_irq calls. The rcu_read_lock
in the interrupt handlers only needs to protect against corrupting the
radix tree; the interrupt handlers may access the cq outside the
rcu_read_lock due to the synchronize_irq calls which protect against
premature freeing of the cq.
3. In function mlx4_cq_event(), we change the mlx_warn message to mlx4_dbg.
4. We leave the cq reference count mechanism in place, because it is
still needed for the cq completion tasklet mechanism.
Fixes: 6d90aa5cf1 ("net/mlx4_core: Make sure there are no pending async events when freeing CQ")
Fixes: 225c7b1fee ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use netdev_info and friends before the net_device is registered.
This avoids ugly messages like
"meson8b-dwmac c9410000.ethernet (unnamed net_device) (uninitialized):
Enable RX Mitigation via HW Watchdog Timer"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As found by Olof's build bot, we gain a harmless warning about a
potential uninitialized variable reference in mlx5:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c: In function 'parse_tc_fdb_actions':
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:769:13: warning: 'out_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:811:21: note: 'out_dev' was declared here
This was introduced through the addition of an 'IS_ERR/PTR_ERR' pair
that gcc is unfortunately unable to completely figure out.
The problem being gcc cannot tell that if(IS_ERR()) in
mlx5e_route_lookup_ipv4() is equivalent to checking if(err) later,
so it assumes that 'out_dev' is used after the 'return PTR_ERR(rt)'.
The PTR_ERR_OR_ZERO() case by comparison is fairly easy to detect
by gcc, so it can't get that wrong, so it no longer warns.
Hadar Hen Zion already attempted to fix the warning earlier by adding fake
initializations, but that ended up not fully addressing all warnings, so
I'm reverting it now that it is no longer needed.
Link: http://arm-soc.lixom.net/buildlogs/mainline/v4.10-rc3-98-gcff3b2c/
Fixes: a42485eb0e ("net/mlx5e: TC ipv4 tunnel encap offload error flow fixes")
Fixes: a757d108dc ("net/mlx5e: Fix kbuild warnings for uninitialized parameters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ax.25 socket connection timed out & the sock struct has been
previously taken down ie. sock struct is now a NULL pointer. Checking
the sock_flag causes the segfault. Check if the socket struct pointer
is NULL before checking sock_flag. This segfault is seen in
timed out netrom connections.
Please submit to -stable.
Signed-off-by: Basil Gunn <basil@pacabunga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7bd509e311 ("bpf: add prog_digest and expose it via
fdinfo/netlink") was recently discussed, partially due to
admittedly suboptimal name of "prog_digest" in combination
with sha1 hash usage, thus inevitably and rightfully concerns
about its security in terms of collision resistance were
raised with regards to use-cases.
The intended use cases are for debugging resp. introspection
only for providing a stable "tag" over the instruction sequence
that both kernel and user space can calculate independently.
It's not usable at all for making a security relevant decision.
So collisions where two different instruction sequences generate
the same tag can happen, but ideally at a rather low rate. The
"tag" will be dumped in hex and is short enough to introspect
in tracepoints or kallsyms output along with other data such
as stack trace, etc. Thus, this patch performs a rename into
prog_tag and truncates the tag to a short output (64 bits) to
make it obvious it's not collision-free.
Should in future a hash or facility be needed with a security
relevant focus, then we can think about requirements, constraints,
etc that would fit to that situation. For now, rework the exposed
parts for the current use cases as long as nothing has been
released yet. Tested on x86_64 and s390x.
Fixes: 7bd509e311 ("bpf: add prog_digest and expose it via fdinfo/netlink")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to probe on gcc generated functions on modules. Since
probing on a module is based on its symbol name, it should
be adjusted on actual symbols.
E.g. without this fix, perf probe shows probe definition
on non-exist symbol as below.
$ perf probe -m build-x86_64/net/netfilter/nf_nat.ko -F in_range*
in_range.isra.12
$ perf probe -m build-x86_64/net/netfilter/nf_nat.ko -D in_range
p:probe/in_range nf_nat:in_range+0
With this fix, perf probe correctly shows a probe on
gcc-generated symbol.
$ perf probe -m build-x86_64/net/netfilter/nf_nat.ko -D in_range
p:probe/in_range nf_nat:in_range.isra.12+0
This also fixes same problem on online module as below.
$ perf probe -m i915 -D assert_plane
p:probe/assert_plane i915:assert_plane.constprop.134+0
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/148411450673.9978.14905987549651656075.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add error check codes on post processing and improve it for offline
probe events as:
- post processing fails if no matched symbol found in map(-ENOENT)
or strdup() failed(-ENOMEM).
- Even if the symbol name is the same, it updates symbol address
and offset.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/148411443738.9978.4617979132625405545.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Until now, we allocate memory always with GFP_ATOMIC flag.
When the system is under memory pressure and a user tries to send,
the send fails due to low memory. However, the user application
can wait for free memory if we allocate it using GFP_KERNEL flag.
In this commit, we use allocate memory with GFP_KERNEL for all user
allocation.
Reported-by: Rune Torgersen <runet@innovsys.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dp83867 driver returns error if phy interface type
PHY_INTERFACE_MODE_RGMII_RXID is used to set the rx only internal
delay. Similarly issue happens for PHY_INTERFACE_MODE_RGMII_TXID.
Fix this by checking also the interface type if a particular delay
value is missing in the phy dt bindings. Also update the DT document
accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ip6gre we have a tunnel header which also makes the tunnel MTU
smaller. We need to reserve room for it. Previously we were using up
space reserved for the Tunnel Encapsulation Limit option
header (RFC 2473).
Also, after commit b05229f442 ("gre6: Cleanup GREv6 transmit path,
call common GRE functions") our contract with the caller has
changed. Now we check if the packet length exceeds the tunnel MTU after
the tunnel header has been pushed, unlike before.
This is reflected in the check where we look at the packet length minus
the size of the tunnel header, which is already accounted for in tunnel
MTU.
Fixes: b05229f442 ("gre6: Cleanup GREv6 transmit path, call common GRE functions")
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to show correct locations for events on modules by relocating given
address instead of retrying after failure.
This happens when the module text size is big enough, bigger than
sh_addr, because the original code retries with given address + sh_addr
if it failed to find CU DIE at the given address.
Any address smaller than sh_addr always fails and it retries with the
correct address, but addresses bigger than sh_addr will get a CU DIE
which is on the given address (not adjusted by sh_addr).
In my environment(x86-64), the sh_addr of ".text" section is 0x10030.
Since i915 is a huge kernel module, we can see this issue as below.
$ grep "[Tt] .*\[i915\]" /proc/kallsyms | sort | head -n1
ffffffffc0270000 t i915_switcheroo_can_switch [i915]
ffffffffc0270000 + 0x10030 = ffffffffc0280030, so we'll check
symbols cross this boundary.
$ grep "[Tt] .*\[i915\]" /proc/kallsyms | grep -B1 ^ffffffffc028\
| head -n 2
ffffffffc027ff80 t haswell_init_clock_gating [i915]
ffffffffc0280110 t valleyview_init_clock_gating [i915]
So setup probes on both function and see what happen.
$ sudo ./perf probe -m i915 -a haswell_init_clock_gating \
-a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
$ sudo ./perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on i915_vga_set_decode:4@gpu/drm/i915/i915_drv.c in i915)
As you can see, haswell_init_clock_gating is correctly shown,
but valleyview_init_clock_gating is not.
With this patch, both events are shown correctly.
$ sudo ./perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
Committer notes:
In my case:
# perf probe -m i915 -a haswell_init_clock_gating -a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
# perf probe -l
probe:haswell_init_clock_gating (on i915_getparam+432@gpu/drm/i915/i915_drv.c in i915)
probe:valleyview_init_clock_gating (on __i915_printk+240@gpu/drm/i915/i915_drv.c in i915)
#
# readelf -SW /lib/modules/4.9.0+/build/vmlinux | egrep -w '.text|Name'
[Nr] Name Type Address Off Size ES Flg Lk Inf Al
[ 1] .text PROGBITS ffffffff81000000 200000 822fd3 00 AX 0 0 4096
#
So both are b0rked, now with the fix:
# perf probe -m i915 -a haswell_init_clock_gating -a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
# perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
#
Both looks correct.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/148411436777.9978.1440275861947194930.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This is an IPv6 version of commit 24803f38a5 ("igmp: do not remove igmp
souce list..."). In mld_del_delrec(), we will restore back all source filter
info instead of flush them.
Move mld_clear_delrec() from ipv6_mc_down() to ipv6_mc_destroy_dev() since
we should not remove source list info when set link down. Remove
igmp6_group_dropped() in ipv6_mc_destroy_dev() since we have called it in
ipv6_mc_down().
Also clear all source info after igmp6_group_dropped() instead of in it
because ipv6_mc_down() will call igmp6_group_dropped().
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bugs.
-----BEGIN PGP SIGNATURE-----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=tb4L
-----END PGP SIGNATURE-----
Merge tag 'nfsd-4.10-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Miscellaneous nfsd bugfixes, one for a 4.10 regression, three for
older bugs"
* tag 'nfsd-4.10-1' of git://linux-nfs.org/~bfields/linux:
svcrdma: avoid duplicate dma unmapping during error recovery
sunrpc: don't call sleeping functions from the notifier block callbacks
svcrpc: don't leak contexts on PROC_DESTROY
nfsd: fix supported attributes for acl & labels
The following patch was sketched by Russell in response to my
crashes on the PB11MPCore after the patch for software-based
priviledged no access support for ARMv8.1. See this thread:
http://marc.info/?l=linux-arm-kernel&m=144051749807214&w=2
I am unsure what is going on, I suspect everyone involved in
the discussion is. I just want to repost this to get the
discussion restarted, as I still have to apply this patch
with every kernel iteration to get my PB11MPCore Realview
running.
Testing by Neil Armstrong on the Oxnas NAS has revealed that
this bug exist also on that widely deployed hardware, so
we are probably currently regressing all ARM11MPCore systems.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: a5e090acbf ("ARM: software-based priviledged-no-access support")
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During interface opening MAC address stored in netdev->dev_addr is
programmed in the HW with exception of BE3 VFs where the initial
MAC is programmed by parent PF. This is OK when MAC address is not
changed when an interfaces is down. In this case the requested MAC is
stored to netdev->dev_addr and later is stored into HW during opening.
But this is not done for all BE3 VFs so the NIC HW does not know
anything about this change and all traffic is filtered.
This is the case of bonding if fail_over_mac == 0 where the MACs of
the slaves are changed while they are down.
The be2net behavior is too restrictive because if a BE3 VF has
the FILTMGMT privilege then it is able to modify its MAC without
any restriction.
To solve the described problem the driver should take care about these
privileged BE3 VFs so the MAC is programmed during opening. And by
contrast unpriviled BE3 VFs should not be allowed to change its MAC
in any case.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
BE3 VFs without FILTMGMT privilege are not allowed to modify its MAC,
VLAN table and UC/MC lists. So don't try to delete MAC on such VFs.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return value from be_mcc_notify_wait() contains a base completion status
together with an additional status. The base_status() macro need to be
used to access base status.
Fixes: e3a7ae2 be2net: Changing MAC Address of a VF was broken
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The #warning was present 10 years ago when the driver first got merged.
As the platform is rather obsolete by now, it seems very unlikely that
the warning will cause anyone to fix the code properly.
kernelci.org reports the warning for every build in the meantime, so
I think it's better to just turn it into a code comment to reduce
noise.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update my entries in the MAINTAINERS file with the same email address
for kernel work, and, now that the git tree is hosted on more suitable
hardware, add git tree references where appropriate.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Disable BH around the call to napi_schedule() to avoid following warning
[ 52.095499] NOHZ: local_softirq_pending 08
[ 52.421291] NOHZ: local_softirq_pending 08
[ 52.608313] NOHZ: local_softirq_pending 08
Fixes: 8d59de8f7b ("net/mlx4_en: Process all completions in RX rings after port goes up")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Erez Shitrit <erezsh@mellanox.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2017-01-16
Here are a couple of important 802.15.4 driver fixes for the 4.10
kernel.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Regressions for not being able to detect an eMMC HS DDR mode card has been
reported for the sdhci-esdhc-imx driver, but potentially other sdhci
variants may suffer from the similar problem.
The commit e173f8911f ("mmc: core: Update CMD13 polling policy when
switch to HS DDR mode"), is causing the problem. It seems that change moved
one step to far, regarding changing the host's timing before polling for a
busy card.
To fix this, let's move back to the behaviour when the host's timing is
updated after the polling, but before the switch status is fetched and
validated.
In cases when polling with CMD13, we keep validating the switch status at
each attempt. However, to align with the other card busy detections
mechanism, let's fetch and validate the switch status also after the host's
timing is updated.
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reported-by: Gary Bisson <gary.bisson@boundarydevices.com>
Fixes: e173f8911f ("mmc: core: Update CMD13 polling policy when switch..")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Mathieu reported that the LTTNG modules are broken as of 4.10-rc1 due to
the removal of the cpu hotplug notifiers.
Usually I don't care much about out of tree modules, but LTTNG is widely
used in distros. There are two ways to solve that:
1) Reserve a hotplug state for LTTNG
2) Add a dynamic range for the prepare states.
While #1 is the simplest solution, #2 is the proper one as we can convert
in tree users, which do not care about ordering, to the dynamic range as
well.
Add a dynamic range which allows LTTNG to request states in the prepare
stage.
Reported-and-tested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Sewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1701101353010.3401@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Uninitialized char* causes a sparse build-warning, fix it up by
initializing it to NULL.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USBTrdTim must be programmed to 0x5 when phy has a UTMI+ 16-bit wide
interface or 0x9 when it has a 8-bit wide interface.
GUSBCFG reset value (Value After Reset: 0x1400) sets USBTrdTim to 0x5.
In case of 8-bit UTMI+, without clearing GUSBCFG.USBTRDTIM mask, USBTrdTim
results in 0xD (0x5 | 0x9).
That's why we need to clear GUSBCFG.USBTRDTIM mask before setting USBTrdTim
value, to ensure USBTrdTim is correctly set in case of 8-bit UTMI+.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull an urgent RCU fix from Paul E. McKenney:
"This series contains a pair of commits that permit RCU synchronous grace
periods (synchronize_rcu() and friends) to work correctly throughout boot.
This eliminates the current "dead time" starting when the scheduler spawns
its first taks and ending when the last of RCU's kthreads is spawned
(this last happens during early_initcall() time). Although RCU's
synchronous grace periods have long been documented as not working
during this time, prior to 4.9, the expedited grace periods worked by
accident, and some ACPI code came to rely on this unintentional behavior.
(Note that this unintentional behavior was -not- reliable. For example,
failures from ACPI could occur on !SMP systems and on systems booting
with the rcu_normal kernel boot parameter.)
Either way, there is a bug that needs fixing, and the 4.9 switch of RCU's
expedited grace periods to workqueues could be considered to have caused
a regression. This series therefore makes RCU's expedited grace periods
operate correctly throughout the boot process. This has been demonstrated
to fix the problems ACPI was encountering, and has the added longer-term
benefit of simplifying RCU's behavior."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We have quite a lot of code that depends on the order of the
__ctl_load inline assemby and subsequent memory accesses, like
e.g. disabling lowcore protection and the writing to lowcore.
Since the __ctl_load macro does not have memory barrier semantics, nor
any other dependencies the compiler is, theoretically, free to shuffle
code around. Or in other words: storing to lowcore could happen before
lowcore protection is disabled.
In order to avoid this class of potential bugs simply add a full
memory barrier to the __ctl_load macro.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
in actually sending them out - will try to do better in
the future:
* handle VHT opmode properly when hostapd is controlling
full station state
* two fixes for minimum channel width in mac80211
* don't leave SMPS set to junk in HT capabilities
* fix headroom when forwarding mesh packets, recently
broken by another fix that failed to take into account
frame encryption
* fix the TID in null-data packets indicating EOSP (end
of service period) in U-APSD
* prevent attempting to use (and then failing which
results in crashes) TXQs on stations that aren't added
to the driver yet
-----BEGIN PGP SIGNATURE-----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=GU6q
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have a number of fixes, in part because I was late
in actually sending them out - will try to do better in
the future:
* handle VHT opmode properly when hostapd is controlling
full station state
* two fixes for minimum channel width in mac80211
* don't leave SMPS set to junk in HT capabilities
* fix headroom when forwarding mesh packets, recently
broken by another fix that failed to take into account
frame encryption
* fix the TID in null-data packets indicating EOSP (end
of service period) in U-APSD
* prevent attempting to use (and then failing which
results in crashes) TXQs on stations that aren't added
to the driver yet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull namespace fixes from Eric Biederman:
"This tree contains 4 fixes.
The first is a fix for a race that can causes oopses under the right
circumstances, and that someone just recently encountered.
Past that are several small trivial correct fixes. A real issue that
was blocking development of an out of tree driver, but does not appear
to have caused any actual problems for in-tree code. A potential
deadlock that was reported by lockdep. And a deadlock people have
experienced and took the time to track down caused by a cleanup that
removed the code to drop a reference count"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
sysctl: Drop reference added by grab_header in proc_sys_readdir
pid: fix lockdep deadlock warning due to ucount_lock
libfs: Modify mount_pseudo_xattr to be clear it is not a userspace mount
mnt: Protect the mountpoint hashtable with mount_lock
Here are some small char/misc driver fixes for 4.10-rc4 that resolve
some reported issues. The MEI driver issue resolves a lot of problems
that people have been having, as does the mem driver fix. The other
minor fixes resolve other reported issues.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWHtrhQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk7xACeJZyxp00SO0WqDZlOWmLShYtwfdEAoLgT3A7t
JkoIfE+/JNbpfLAPwl4N
=gSvf
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc driver fixes for 4.10-rc4 that resolve
some reported issues.
The MEI driver issue resolves a lot of problems that people have been
having, as does the mem driver fix. The other minor fixes resolve
other reported issues.
All of these have been in linux-next for a while"
* tag 'char-misc-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
vme: Fix wrong pointer utilization in ca91cx42_slave_get
auxdisplay: fix new ht16k33 build errors
ppdev: don't print a free'd string
extcon: return error code on failure
drivers: char: mem: Fix thinkos in kmem address checks
mei: bus: enable OS version only for SPT and newer
Here is a single patch being reverted to remove a feature that was added
in 4.10-rc1 that isn't quite ready for release. It will be redone as a
debugfs file instead of a sysfs file in the future.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWHtr+A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymkJQCfZgr9tNZfzUZxojP6lEIiSAEsDO0Anj8l1ZZf
PRICi50BvVtENhOyE25m
=arvB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single patch being reverted to remove a feature that was
added in 4.10-rc1 that isn't quite ready for release.
It will be redone as a debugfs file instead of a sysfs file in the
future"
* tag 'driver-core-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Revert "driver core: Add deferred_probe attribute to devices in sysfs"
Here are some small tty/serial driver fixes for 4.10-rc4 to resolve a
number of reported issues.
Nothing major here at all, one revert of a problematic patch, and some
other tiny bugfixes. Full details are in the shortlog below.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWHtshA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym6PQCeJtdwrkIQmisQZYcMpAZrnQnpF9YAnjrcqWZ4
2glC2IsH8mDm5DR81axE
=GIdT
-----END PGP SIGNATURE-----
Merge tag 'tty-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty/serial driver fixes for 4.10-rc4 to resolve a
number of reported issues.
Nothing major here at all, one revert of a problematic patch, and some
other tiny bugfixes. Full details are in the shortlog below.
All have been in linux-next with no reported issues"
* tag 'tty-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
sysrq: attach sysrq handler correctly for 32-bit kernel
Revert "tty: serial: 8250: add CON_CONSDEV to flags"
Clearing FIFOs in RS485 emulation mode causes subsequent transmits to break
8250_pci: Fix potential use-after-free in error path
tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done
tty/serial: atmel_serial: BUG: stop DMA from transmitting in stop_tx
Here are a few small USB driver fixes for 4.10-rc4 to resolve some
reported issues. The "largest" here is a number of bugs being fixed in
the ch341 usb-serial driver, to hopefully resolve the mess of different
devices floating around that use this driver that have been having
problems with the 4.10-rc1 release. There's also a tiny musb fix that I
missed in the last pull request, as well as the traditional xhci fix
rounding out the batch.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWHttLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylfnQCguPTDSPkdU5vSsu8eCEplsql6izUAnjz5WAuI
YDQBXrYkmQ5HRM4U2/8T
=M2Eg
-----END PGP SIGNATURE-----
Merge tag 'usb-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a few small USB driver fixes for 4.10-rc4 to resolve some
reported issues.
The "largest" here is a number of bugs being fixed in the ch341
usb-serial driver, to hopefully resolve the mess of different devices
floating around that use this driver that have been having problems
with the 4.10-rc1 release.
There's also a tiny musb fix that I missed in the last pull request,
as well as the traditional xhci fix rounding out the batch.
All have been in linux-next with no reported issues"
* tag 'usb-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: fix deadlock at host remove by running watchdog correctly
USB: serial: ch341: fix control-message error handling
usb: musb: fix runtime PM in debugfs
wusbcore: Fix one more crypto-on-the-stack bug
USB: serial: kl5kusb105: fix line-state error handling
USB: serial: ch341: fix baud rate and line-control handling
USB: serial: ch341: fix line settings after reset-resume
USB: serial: ch341: fix resume after reset
USB: serial: ch341: fix open error handling
USB: serial: ch341: fix modem-control and B0 handling
USB: serial: ch341: fix open and resume after B0
USB: serial: ch341: fix initial modem-control state
Pull i2c fixes from Wolfram Sang:
"Bugfixes for I2C. Mostly core this time which is a bit unusual but
nothing really scary in there"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: piix4: Avoid race conditions with IMC
i2c: fix spelling mistake: "insufficent" -> "insufficient"
i2c: print correct device invalid address
i2c: do not enable fall back to Host Notify by default
i2c: fix kernel memory disclosure in dev interface
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- unwinder fixes
- AMD CPU topology enumeration fixes
- microcode loader fixes
- x86 embedded platform fixes
- fix for a bootup crash that may trigger when clearcpuid= is used
with invalid values"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mpx: Use compatible types in comparison to fix sparse error
x86/tsc: Add the Intel Denverton Processor to native_calibrate_tsc()
x86/entry: Fix the end of the stack for newly forked tasks
x86/unwind: Include __schedule() in stack traces
x86/unwind: Disable KASAN checks for non-current tasks
x86/unwind: Silence warnings for non-current tasks
x86/microcode/intel: Use correct buffer size for saving microcode data
x86/microcode/intel: Fix allocation size of struct ucode_patch
x86/microcode/intel: Add a helper which gives the microcode revision
x86/microcode: Use native CPUID to tickle out microcode revision
x86/CPU: Add native CPUID variants returning a single datum
x86/boot: Add missing declaration of string functions
x86/CPU/AMD: Fix Bulldozer topology
x86/platform/intel-mid: Rename 'spidev' to 'mrfld_spidev'
x86/cpu: Fix typo in the comment for Anniedale
x86/cpu: Fix bootup crashes by sanitizing the argument of the 'clearcpuid=' command-line option
Pull NOHZ fix from Ingo Molnar:
"This fixes an old NOHZ race where we incorrectly calculate the next
timer interrupt in certain circumstances where hrtimers are pending,
that can cause hard to reproduce stalled-values artifacts in
/proc/stat"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: Fix collision between tick and other hrtimers
Pull perf fixes from Ingo Molnar:
"Misc race fixes uncovered by fuzzing efforts, a Sparse fix, two PMU
driver fixes, plus miscellanous tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Reject non sampling events with precise_ip
perf/x86/intel: Account interrupts for PEBS errors
perf/core: Fix concurrent sys_perf_event_open() vs. 'move_group' race
perf/core: Fix sys_perf_event_open() vs. hotplug
perf/x86/intel: Use ULL constant to prevent undefined shift behaviour
perf/x86/intel/uncore: Fix hardcoded socket 0 assumption in the Haswell init code
perf/x86: Set pmu->module in Intel PMU modules
perf probe: Fix to probe on gcc generated symbols for offline kernel
perf probe: Fix --funcs to show correct symbols for offline module
perf symbols: Robustify reading of build-id from sysfs
perf tools: Install tools/lib/traceevent plugins with install-bin
tools lib traceevent: Fix prev/next_prio for deadline tasks
perf record: Fix --switch-output documentation and comment
perf record: Make __record_options static
tools lib subcmd: Add OPT_STRING_OPTARG_SET option
perf probe: Fix to get correct modname from elf header
samples/bpf trace_output_user: Remove duplicate sys/ioctl.h include
samples/bpf sock_example: Avoid getting ethhdr from two includes
perf sched timehist: Show total scheduling time
Pull EFI fixes from Ingo Molnar:
"A number of regression fixes:
- Fix a boot hang on machines that have somewhat unusual memory map
entries of phys_addr=0x0 num_pages=0, which broke due to a recent
commit. This commit got cherry-picked from the v4.11 queue because
the bug is affecting real machines.
- Fix a boot hang also reported by KASAN, caused by incorrect init
ordering introduced by a recent optimization.
- Fix a recent robustification fix to allocate_new_fdt_and_exit_boot()
that introduced an invalid assumption. Neither bugs were seen in
the wild AFAIK"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Prune invalid memory map entries and fix boot regression
x86/efi: Don't allocate memmap through memblock after mm_init()
efi/libstub/arm*: Pass latest memory map to the kernel
Some drivers do depend on page mappings to be page aligned.
Swiotlb already enforces such alignment for mappings greater than page,
extend that to page-sized mappings as well.
Without this fix, nvme hits BUG() in nvme_setup_prps(), because that routine
assumes page-aligned mappings.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
