The legacy ethtool userspace tool shows an error when no features could
be changed. It's useful to have a netlink reply to be able to show this
error when __netdev_update_features wasn't called, for example:
1. ethtool -k eth0
large-receive-offload: off
2. ethtool -K eth0 rx-fcs on
3. ethtool -K eth0 lro on
Could not change any device features
rx-lro: off [requested on]
4. ethtool -K eth0 lro on
# The output should be the same, but without this patch the kernel
# doesn't send the reply, and ethtool is unable to detect the error.
This commit makes ethtool-netlink always return a reply when requested,
and it still avoids unnecessary calls to __netdev_update_features if the
wanted features haven't changed.
Fixes: 0980bfcd69 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool-netlink ignores dev->hw_features and may confuse the drivers by
asking them to enable features not in the hw_features bitmask. For
example:
1. ethtool -k eth0
tls-hw-tx-offload: off [fixed]
2. ethtool -K eth0 tls-hw-tx-offload on
tls-hw-tx-offload: on
3. ethtool -k eth0
tls-hw-tx-offload: on [fixed]
Fitler out dev->hw_features from req_wanted to fix it and to resemble
the legacy ethtool behavior.
Fixes: 0980bfcd69 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ethtool-netlink calculates new wanted bits as:
(req_wanted & req_mask) | (old_active & ~req_mask)
It completely discards the old wanted bits, so they are forgotten with
the next ethtool command. Sample steps to reproduce:
1. ethtool -k eth0
tx-tcp-segmentation: on # TSO is on from the beginning
2. ethtool -K eth0 tx off
tx-tcp-segmentation: off [not requested]
3. ethtool -k eth0
tx-tcp-segmentation: off [requested on]
4. ethtool -K eth0 rx off # Some change unrelated to TSO
5. ethtool -k eth0
tx-tcp-segmentation: off # "Wanted on" is forgotten
This commit fixes it by changing the formula to:
(req_wanted & req_mask) | (old_wanted & ~req_mask),
where old_active was replaced by old_wanted to account for the wanted
bits.
The shortcut condition for the case where nothing was changed now
compares wanted bitmasks, instead of wanted to active.
Fixes: 0980bfcd69 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset introduces some updates to mlx5 driver.
1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
Starting with a hack to allow drivers to request a static configuration
of the default vxlan port, and then a patch that converts mlx5.
2) Parav implements change_carrier ndo for VF eswitch representors,
to speedup link state control of representors netdevices.
3) Alex Vesker, makes a simple update to software steering to fix an issue
with push vlan action sequence
4) Leon removes a redundant dump stack on error flow.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl8oRdgACgkQSD+KveBX
+j4/LQgAkSjNzOaS7bVDzhoYL3aBQOMIzgocJUeVi7xXH8IO1uy55mNDrKBqjxbW
dy9U9VsvV5i2V2qkkQLvHVkoDSg8Buo2Uxu4OrZHOLN0KfbFrra4VvmB1CzEBix8
FICnQaZZcE7529P04TgZ8Mo9vRb5VdJFhqED5Nvegy+y8FolEsQYbjIoDBE6wa0j
Meqa/29+XCE5FzTOjbbQWizAnRZMbkxtSSreDNgeHxke9eMSO+fmwKScng63QUfl
7nfU6dW6A0d1kHhpL5RqAFOcmkpSdqYaA3SA+/8pPT9X3yOAkxE6KTKGIixpB9JX
zQt+Wkna49jJ/JfDQB5vgww5c0HjAQ==
=j0fG
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-08-03
This patchset introduces some updates to mlx5 driver.
1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
Starting with a hack to allow drivers to request a static configuration
of the default vxlan port, and then a patch that converts mlx5.
2) Parav implements change_carrier ndo for VF eswitch representors,
to speedup link state control of representors netdevices.
3) Alex Vesker, makes a simple update to software steering to fix an issue
with push vlan action sequence
4) Leon removes a redundant dump stack on error flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
info cannot be NULL here since its being accessed earlier
in the function: nlmsg_parse(info->nlhdr...). Remove this
redundant NULL check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5 has the IANA VXLAN port (4789) hard coded by the device,
instead of being added dynamically when tunnels are created.
To support this add a workaround flag to struct udp_tunnel_nic_info.
Skipping updates for the port is fairly trivial, dumping the hard
coded port via ethtool requires some code duplication. The port
is not a part of any real table, we dump it in a special table
which has no tunnel types supported and only one entry.
This is the last known workaround / hack needed to convert
all drivers to the new infra.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add an interface to report offloaded UDP ports via ethtool netlink.
Now that core takes care of tracking which UDP tunnel ports the NICs
are aware of we can quite easily export this information out to
user space.
The responsibility of writing the netlink dumps is split between
ethtool code and udp_tunnel_nic.c - since udp_tunnel module may
not always be loaded, yet we should always report the capabilities
of the NIC.
$ ethtool --show-tunnels eth0
Tunnel information for eth0:
UDP port table 0:
Size: 4
Types: vxlan
No entries
UDP port table 1:
Size: 4
Types: geneve, vxlan-gpe
Entries (1):
port 1230, vxlan-gpe
v4:
- back to v2, build fix is now directly in udp_tunnel.h
v3:
- don't compile ETHTOOL_MSG_TUNNEL_INFO_GET in if CONFIG_INET
not set.
v2:
- fix string set count,
- reorder enums in the uAPI,
- fix type of ETHTOOL_A_TUNNEL_UDP_TABLE_TYPES to bitset
in docs and comments.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the genlmsg_put() call in ethnl_default_dumpit() fails, we bail out
without checking if we already have some messages in current skb like we do
with ethnl_default_dump_one() failure later. Therefore if existing messages
almost fill up the buffer so that there is not enough space even for
netlink and genetlink header, we lose all prepared messages and return and
error.
Rather than duplicating the skb->len check, move the genlmsg_put(),
genlmsg_cancel() and genlmsg_end() calls into ethnl_default_dump_one().
This is also more logical as all message composition will be in
ethnl_default_dump_one() and only iteration logic will be left in
ethnl_default_dumpit().
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define 100G, 200G and 400G link modes using 100Gbps per lane
LR, ER and FR are defined as a single link mode because they are
using same technology and by design are fully interoperable.
EEPROM content indicates if the module is LR, ER, or FR, and the
user space ethtool decoder is planned to support decoding these
modes in the EEPROM.
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have moved the PHY ethtool statistics to be dynamically
registered, we no longer need to inline those for ethtool. This used to
be done to avoid cross symbol referencing and allow ethtool to be
decoupled from PHYLIB entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have introduced ethtool_phy_ops and the PHY library
dynamically registers its operations with that function pointer, we can
remove the direct PHYLIB dependency in favor of using dynamic
operations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to decouple ethtool from its PHY library dependency, define an
ethtool_phy_ops singleton which can be overriden by the PHY library when
it loads with an appropriate set of function pointers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, drivers can only tell whether the link is up/down using
LINKSTATE_GET, but no additional information is given.
Add attributes to LINKSTATE_GET command in order to allow drivers
to expose the user more information in addition to link state to ease
the debug process, for example, reason for link down state.
Extended state consists of two attributes - link_ext_state and
link_ext_substate. The idea is to avoid 'vendor specific' states in order
to prevent drivers to use specific link_ext_state that can be in the future
common link_ext_state.
The substates allows drivers to add more information to the common
link_ext_state. For example, vendor can expose 'Autoneg' as link_ext_state
and add 'No partner detected during force mode' as link_ext_substate.
If a driver cannot pinpoint the extended state with the substate
accuracy, it is free to expose only the extended state and omit the
substate attribute.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
When getting SQI or maximum SQI value fails in linkstate_prepare_data(), we
must not return without calling ethnl_ops_complete(dev) as that could
result in imbalance between ethtool_ops ->begin() and ->complete() calls.
Fixes: 8066021915 ("ethtool: provide UAPI for PHY Signal Quality Index (SQI)")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
A last minute change put the TDR cable test parameters into a nest.
The validation is not sufficient, resulting in an oops if the nest is
missing. Set default values first, then update them if the nest is
provided.
Fixes: f2bc8ad31a ("net: ethtool: Allow PHY cable test TDR data to configured")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e585f23636 ("udp: Changes to udp_offload to support remote
checksum offload") added new GSO type and a corresponding netdev
feature, but missed Ethtool's 'netdev_features_strings' table.
Give it a name so it will be exposed to userspace and become available
for manual configuration.
v3:
- decouple from "netdev_features_strings[] cleanup" series;
- no functional changes.
v2:
- don't split the "Fixes:" tag across lines;
- no functional changes.
Fixes: e585f23636 ("udp: Changes to udp_offload to support remote checksum offload")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix check in ethtool_rx_flow_rule_create
Fixes: eca4205f9e ("ethtool: add ethtool_rx_flow_spec to flow_rule structure translator")
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3b33583265 ("net: Add fraglist GRO/GSO feature flags") missed
an entry for NETIF_F_GSO_FRAGLIST in netdev_features_strings array. As
a result, fraglist GSO feature is not shown in 'ethtool -k' output and
can't be toggled on/off.
The fix is trivial.
Fixes: 3b33583265 ("net: Add fraglist GRO/GSO feature flags")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use array_size() helper instead of the open-coded version in
copy_to_user(). These sorts of multiplication factors need to
be wrapped in array_size().
This issue was found with the help of Coccinelle and, audited and fixed
manually.
Addresses-KSPP-ID: https://github.com/KSPP/linux/issues/83
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code generates a Smatch warning:
net/ethtool/linkinfo.c:143 ethnl_set_linkinfo()
warn: variable dereferenced before check 'info' (see line 119)
Fortunately, the "info" pointer is never NULL so the check can be
removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild test robot is reporting:
net/ethtool/cabletest.c:230:5: warning: no previous prototype for
Mark the function as static.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.
If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers for returning raw TDR helpers in netlink messages.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
get_coalesce returns 0 or ERRNO, but the return value isn't checked.
The returned coalesce data may be invalid if an ERRNO is set,
therefore better check and propagate the return value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-05-23
The following pull-request contains BPF updates for your *net-next* tree.
We've added 50 non-merge commits during the last 8 day(s) which contain
a total of 109 files changed, 2776 insertions(+), 2887 deletions(-).
The main changes are:
1) Add a new AF_XDP buffer allocation API to the core in order to help
lowering the bar for drivers adopting AF_XDP support. i40e, ice, ixgbe
as well as mlx5 have been moved over to the new API and also gained a
small improvement in performance, from Björn Töpel and Magnus Karlsson.
2) Add getpeername()/getsockname() attach types for BPF sock_addr programs
in order to allow for e.g. reverse translation of load-balancer backend
to service address/port tuple from a connected peer, from Daniel Borkmann.
3) Improve the BPF verifier is_branch_taken() logic to evaluate pointers
being non-NULL, e.g. if after an initial test another non-NULL test on
that pointer follows in a given path, then it can be pruned right away,
from John Fastabend.
4) Larger rework of BPF sockmap selftests to make output easier to understand
and to reduce overall runtime as well as adding new BPF kTLS selftests
that run in combination with sockmap, also from John Fastabend.
5) Batch of misc updates to BPF selftests including fixing up test_align
to match verifier output again and moving it under test_progs, allowing
bpf_iter selftest to compile on machines with older vmlinux.h, and
updating config options for lirc and v6 segment routing helpers, from
Stanislav Fomichev, Andrii Nakryiko and Alan Maguire.
6) Conversion of BPF tracing samples outdated internal BPF loader to use
libbpf API instead, from Daniel T. Lee.
7) Follow-up to BPF kernel test infrastructure in order to fix a flake in
the XDP selftests, from Jesper Dangaard Brouer.
8) Minor improvements to libbpf's internal hashmap implementation, from
Ian Rogers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the AF_XDP zero-copy driver interface to its own include file
called xdp_sock_drv.h. This, hopefully, will make it more clear for
NIC driver implementors to know what functions to use for zero-copy
support.
v4->v5: Fix -Wmissing-prototypes by include header file. (Jakub)
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-4-bjorn.topel@gmail.com
As ethnl_request_ops::reply_size handlers do not include common header
size into calculated/estimated reply size, it needs to be added in
ethnl_default_doit() and ethnl_default_notify() before allocating the
message. On the other hand, strset_reply_size() should not add common
header size.
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't call drivers if nothing changed. Netlink code already
contains this logic.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having a channel config with no ability to RX or TX traffic is
clearly wrong. Check for this in the core so the drivers don't
have to.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given that it takes time to run a cable test, send a notify message at
the start, as well as when it is completed.
v3:
EMSGSIZE when ethnl_bcastmsg_put() fails
Print an error message on failure, since this is a void function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PHY drivers can use these helpers for reporting the results. The
results get translated into netlink attributes which are added to the
pre-allocated skbuf.
v3:
Poison phydev->skb
Return -EMSGSIZE when ethnl_bcastmsg_put() fails
Return valid error code when nla_nest_start() fails
Use u8 for results
Actually put u32 length into message
v4:
s/ENOTSUPP/EOPNOTSUPP/g
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide infrastructure for PHY drivers to report the cable test
results. A netlink skb is associated to the phydev. Helpers will be
added which can add results to this skb. Once the test has finished
the results are sent to user space.
When netlink ethtool is not part of the kernel configuration stubs are
provided. It is also impossible to trigger a cable test, so the error
code returned by the alloc function is of no consequence.
v2:
Include the status complete in the netlink notification message
v4:
Replace -EINVAL with -EMSGSIZE
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make some helpers for building ethtool netlink messages available
outside the compilation unit, so they can be used for building
messages which are not simple get/set.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new ethtool netlink calls to trigger the starting of a PHY cable
test.
Add Kconfig'ury to ETHTOOL_NETLINK so that PHYLIB is not a module when
ETHTOOL_NETLINK is builtin, which would result in kernel linking errors.
v2:
Remove unwanted white space change
Remove ethnl_cable_test_act_ops and use doit handler
Rename cable_test_set_policy cable_test_act_policy
Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY
v3:
Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY from documentation
Remove unused cable_test_get_policy
Add Reviewed-by tags
v4:
Remove unwanted blank line
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of linux/vermagic.h includes, so that MODULE_ARCH_VERMAGIC from
the arch header arch/x86/include/asm/module.h won't be redefined.
In file included from ./include/linux/module.h:30,
from drivers/net/ethernet/3com/3c515.c:56:
./arch/x86/include/asm/module.h:73: warning: "MODULE_ARCH_VERMAGIC"
redefined
73 | # define MODULE_ARCH_VERMAGIC MODULE_PROC_FAMILY
|
In file included from drivers/net/ethernet/3com/3c515.c:25:
./include/linux/vermagic.h:28: note: this is the location of the
previous definition
28 | #define MODULE_ARCH_VERMAGIC ""
|
Fixes: 6bba2e89a8 ("net/3com: Delete driver and module versions from 3com drivers")
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Shannon Nelson <snelson@pensando.io> # ionic
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is executing a self test, put the interface into
operative status testing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement TSINFO_GET request to get timestamping information for a network
device. This is traditionally available via ETHTOOL_GET_TS_INFO ioctl
request.
Move part of ethtool_get_ts_info() into common.c so that ioctl and netlink
code use the same logic to get timestamping information from the device.
v3: use "TSINFO" rather than "TIMESTAMP", suggested by Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add three string sets related to timestamping information:
ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags
ETH_SS_TS_TX_TYPES: timestamping Tx types
ETH_SS_TS_RX_FILTERS: timestamping Rx filters
These will be used for TIMESTAMP_GET request.
v2: avoid compiler warning ("enumeration value not handled in switch")
in net_hwtstamp_validate()
v3: omit dash in Tx type names ("one-step-*" -> "onestep-*"), suggested by
Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_EEE_NTF notification whenever EEE settings of a network
device are modified using ETHTOOL_MSG_EEE_SET netlink message or
ETHTOOL_SEEE ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement EEE_SET netlink request to set EEE settings of a network device.
These are traditionally set with ETHTOOL_SEEE ioctl request.
The netlink interface allows setting the EEE status for all link modes
supported by kernel but only first 32 link modes can be set at the moment
as only those are supported by the ethtool_ops callback.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement EEE_GET request to get EEE settings of a network device. These
are traditionally available via ETHTOOL_GEEE ioctl request.
The netlink interface allows reporting EEE status for all link modes
supported by kernel but only first 32 link modes are provided at the moment
as only those are reported by the ethtool_ops callback and drivers.
v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_PAUSE_NTF notification whenever pause parameters of
a network device are modified using ETHTOOL_MSG_PAUSE_SET netlink message
or ETHTOOL_SPAUSEPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement PAUSE_SET netlink request to set pause parameters of a network
device. Thease are traditionally set with ETHTOOL_SPAUSEPARAM ioctl
request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement PAUSE_GET request to get pause parameters of a network device.
These are traditionally available via ETHTOOL_GPAUSEPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
