The same way we support these two operations for USB4 routers we can
extend the retimer NVM operations to support retimers also.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With help from platform firmware (ACPI) it is possible to power on
retimers even when there is no USB4 link (e.g nothing is connected to
the USB4 ports). This allows us to bring the USB4 sideband up so that we
can access retimers and upgrade their NVM firmware.
If the platform has support for this, we expose two additional
attributes under USB4 ports: offline and rescan. These can be used to
bring the port offline, rescan for the retimers and put the port online
again. The retimer NVM upgrade itself works the same way than with cable
connected.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create devices for each USB4 port. This is needed when we add retimer
access when there is no device connected but may be useful for other
purposes too following what USB subsystem does. This exports a single
attribute "link" that shows the type of the USB4 link (or "none" if
there is no cable connected).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This array uses 1-based indexing so it corrupts memory one element
beyond of the array. Fix it by making the array one element larger.
Fixes: dacb12877d ("thunderbolt: Add support for on-board retimers")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
After the device_register() succeeds, then the correct way to clean up
is to call device_unregister(). The unregister calls both device_del()
and device_put(). Since this code was only device_del() it results in
a memory leak.
Fixes: dacb12877d ("thunderbolt: Add support for on-board retimers")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec specifies standard access to retimers (both on-board and
cable) through USB4 port sideband access. This makes it possible to
upgrade their firmware in the same way than we already do with the
routers.
This enumerates on-board retimers under each USB4 port when the link
comes up and adds them to the bus under the router the retimer belongs
to. Retimers are exposed in sysfs with name like <device>:<port>.<index>
where device is the router the retimer belongs to, port is the USB4 port
the retimer is connected to and index is the retimer index under that
port (starting from 1). This applies to the upstream USB4 port as well
so if there is on-board retimer between the port and the router it is
also added accordingly.
At this time we do not add cable retimers but there is no techincal
restriction to do so in the future if needed. It is not clear whether it
makes sense to upgrade their firmwares and at least Thunderbolt 3 cables
it has not been done outside of lab environments.
The sysfs interface is made to follow the router NVM upgrade to make it
easy to extend the existing userspace (fwupd) to handle these as well.
Signed-off-by: Kranthi Kuntala <kranthi.kuntala@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
