We detect and enable the use of the PL110 variant, an earlier
incarnation of PL111. The only real difference is that the
control and interrupt enable registers have swapped place.
The Versatile AB and Versatile PB have a variant inbetween
PL110 and PL111, it is PL110 but they have already swapped the
two registers so those two need a bit of special handling.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-4-linus.walleij@linaro.org
This replaces the custom connector in the PL111 with the
panel bridge helper.
This works nicely for all standard panels, but since there
are several PL11x-based systems that will need to use the dumb
VGA connector bridge we use drm_of_find_panel_or_bridge()
and make some headroom for dealing with bridges that are
not panels as well, and drop a TODO in the code.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-3-linus.walleij@linaro.org
If we want to have vblank on both pipelines at the same time, we need
to call drm_vblank_init with num_crtcs = 2.
Instead, since the crtc init calls correctly set mode_config.num_crtc,
we can move the drm_vblank_init call to after the crtc init code is
called, which is the component bind part. Then we can just pass
mode_config.num_crtc in.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908075016.18657-8-wens@csie.org
The TCON has a mux to select the source of the data to display.
This mux includes selecting the display backends. On the A31,
which has two display pipelines, this mux can let the TCON
select either backend as its data source. Although the muxing
can be changed on the fly, DRM needs to be able to group a
bunch of layers such that they get switched to another crtc
together. This is because the display backend does the layer
compositing, while the TCON generates the display timings.
This constraint is not supported by DRM.
Here we simply pair up backends and TCONs with the same ID.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908075016.18657-7-wens@csie.org
Now that sun4i_tcon_find_engine_traverse() usage is restricted to the
single input case, we can remove the for_each_available_child_of_node
loop.
While at it, consolidate all the of_node_put calls into a common exit
path.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908075016.18657-6-wens@csie.org
The device tree binding for sun4i-drm says:
For all connections between components up to the TCONs in the display
pipeline, when there are multiple components of the same type at the
same depth, the local endpoint ID must be the same as the remote
component's index. For example, if the remote endpoint is Frontend 1,
then the local endpoint ID must be 1.
We should be able to get the TCON's ID directly from any of the remote
endpoints from its input port. With the ID, we can then go through the
list of registered engines and find a matching one by ID.
However the A31 device tree is incorrect. We assumed that there were no
cross pipeline connections between the backends and TCONs. As a result,
in all the endpoints between the backends and TCONs of the second
display pipeline, the endpoint IDs were incorrectly set to 0, when in
fact they should've been set to 1.
To maintain compatibility with this incorrect device tree, we first
check if the TCON's input port has 1 or many endpoints. If there are
more than 1, then it is likely a fixed version, and we can proceed
with the new method. If there is only 1 endpoint, then it is possibly
an incorrect version, or it could be the SoC only has one pipeline.
In either case we fall back to using the old method of traversing
the input connections to find a matching engine, and then get its
ID.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908075016.18657-5-wens@csie.org
The patch b317fa3ba1 ("drm/sun4i: tcon: Find matching display backend
by device node matching") assumed a one-to-one mapping between TCONs
and backends. This turned out wrong, as we found muxing controls in the
TCON of the A31, and undocumented usage of the backend output selector
of the A20.
Make sun4i_tcon_find_engine() bail out if the current node has multiple
input connections.
Fixes: b317fa3ba1 ("drm/sun4i: tcon: Find matching display backend
by device node matching")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908075016.18657-4-wens@csie.org
The encoder drivers use drm_of_find_possible_crtcs to get upstream
crtcs from the device tree using of_graph. For the results to be
correct, encoders must be probed/bound after _all_ crtcs have been
created. The existing code uses a depth first recursive traversal
of the of_graph, which means the encoders downstream of the TCON
get add right after the first TCON. The second TCON or CRTC will
never be properly associated with encoders connected to it.
Other platforms, such as Rockchip, deal with this by probing all
CRTCs first, then all subsequent components. This is easy to do
since the CRTCs correspond to just one device node, and are the
first nodes in the pipeline.
However with Allwinner SoCs, the function of the CRTC is split
between the display backend (DE 1.0) or mixer (DE 2.0), which does
scan-out and compositing, and the TCON, which generates the display
timing signals. Further complicating the process, there may be a
Dynamic Range Controller between the backend and the TCON. Also, the
backend is preceded by the frontend, with a Display Enhancement Unit
possibly in between.
In a dual display pipeline setup, both frontends can feed either
backend, and both backends can feed either TCON. We want all
components of the same type to be added before the next type in the
pipeline. Fortunately, the pipelines are perfectly symmetric, i.e.
components of the same type are at the same depth when counted from
the frontend. The only exception is the third pipeline in the A80
SoC, which we do not support anyway.
Hence we can use a breadth first search traversal order to add
components. We do not need to check for duplicates. The component
matching system handles this for us.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908075016.18657-3-wens@csie.org
When binding the TCON, we were checking the reset control status and
asserting reset if it wasn't in reset. The check failed to account for
the reset control API returning error codes if the status callback was
not implemented.
Since we want the TCON to be reset in all cases, use reset_control_reset
to force a reset instead.
Fixes: 9026e0d122 ("drm: Add Allwinner A10 Display Engine support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908090016.32224-1-wens@csie.org
The current error handling when devm_kzalloc fails performs a
non-null check on connector which is redundant because connector
is null at that failure point. Once this is removed, make the
failure path into a trivial -ENOMEM return to clean up the
error handling. Also remove need to initialize connector to NULL.
Detected by CoverityScan CID#1339527 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908140504.1340-1-colin.king@canonical.com
By always keeping track of the last commit in plane_state, we know
whether there is an active update on the plane or not. With that
information we can reject the fast update, and force the slowpath
to be used as was originally intended.
We cannot use plane_state->crtc->state here, because this only mentions
the most recent commit for the crtc, but not the planes that were part
of it. We specifically care about what the last commit involving this
plane is, which can only be tracked with a pointer in the plane state.
Changes since v1:
- Clean up the whole function here, instead of partially earlier.
- Add mention in the commit message why we need commit in plane_state.
- Swap plane->state in intel_legacy_cursor_update, instead of
reassigning all variables. With this commit We know that the cursor
is not part of any active commits so this hack can be removed.
Cc: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20170904104838.23822-7-maarten.lankhorst@linux.intel.com
[mlankhorst: Amend commit for merge conflicts with drm-intel]
Currently we neatly track the crtc state, but forget to look at
plane/connector state.
When doing a nonblocking modeset, immediately followed by a setprop
before the modeset completes, the setprop will see the modesets new
state as the old state and free it.
This has to be solved by waiting for hw_done on the connector, even
if it's not assigned to a crtc. When a connector is unbound we take
the last crtc commit, and when it stays unbound we create a new
fake crtc commit for that gets signaled on hw_done for all the
planes/connectors.
We wait for it the same way as we do for crtc's, which will make
sure we never run into a use-after-free situation.
Changes since v1:
- Only create a single disable commit. (danvet)
- Fix leak in intel_legacy_cursor_update.
Changes since v2:
- Make reference counting in drm_atomic_helper_setup_commit
more obvious. (pinchartl)
- Call cleanup_done for fake commit. (danvet)
- Add comments to drm_atomic_helper_setup_commit. (danvet, pinchartl)
- Add comment to drm_atomic_helper_swap_state. (pinchartl)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Testcase: kms_atomic_transition.plane-use-after-nonblocking-unbind*
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170904104838.23822-6-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When commit synchronization through drm_crtc_commit was first
introduced, we tried to solve the problem of the flip_done
needing a reference count by blocking in cleanup_done.
This has been changed by commit 24835e442f ("drm: reference count
event->completion") which made the waits here no longer needed.
However, even after this commit we still needed the wait because
otherwise we cannot wait for the flip_done because this item might
have been removed from the list.
Changed since v1:
- Make mention of cleanup_done completing before flip_done.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170904104838.23822-4-maarten.lankhorst@linux.intel.com
Most code only cares about the current commit or previous commit.
Fortuantely we already have a place to track those. Move it to
drm_crtc_state where it belongs. :)
The per-crtc commit_list is kept for places where we have to look
deeper than the current or previous commit for checking whether to stall
on unpin. This is used in drm_atomic_helper_setup_commit and
intel_has_pending_fb_unpin.
Changes since v1:
- Update kerneldoc for drm_crtc.commit_list. (danvet)
Changes since v2:
- Remove drm_atomic_helper_async_check hunk. (pinchartl)
Changes since v3:
- Fix use-after-free in drm_atomic_helper_commit_cleanup_done().
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170904150456.31049-1-maarten.lankhorst@linux.intel.com
[mlankhorst: preceeding -> preceding (checkpatch)]
The next commit removes the wait for flip_done in in
drm_atomic_helper_commit_cleanup_done, but we need it for the tests
to pass. Instead of using complicated vblank tracking which ends
up being ignored anyway, call the correct atomic helper. :)
Changes since v1:
- Always call drm_atomic_helper_wait_for_flip_done,
even for legacy cursor updates. (danvet)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170904104838.23822-2-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gcc-7 complains about multiplying within a condition being
suspicious:
drivers/gpu/drm/stm/dw_mipi_dsi-stm.c: In function 'dsi_pll_get_clkout_khz':
drivers/gpu/drm/stm/dw_mipi_dsi-stm.c:117:10: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
The code here is correct, but can be easily rephrased to make
that more obvious. I also swap out the error handling and the normal
code path for clarity.
Fixes: b0f09a3c69d9 ("drm/stm: Add STM32 DSI controller driver")
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170906131331.2691300-1-arnd@arndb.de
This adds support for Rockchip soc lvds found on rk3288
Based on the patches from Mark yao and Heiko Stuebner.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sandy Huang <hjc@rock-chips.com>
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1504351737-136042-1-git-send-email-hjc@rock-chips.com
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
gcc-8 points out a condition that almost certainly doesn't
do what the author had in mind:
drivers/gpu/drm/gma500/mdfld_intel_display.c: In function 'mdfldWaitForPipeEnable':
drivers/gpu/drm/gma500/mdfld_intel_display.c:102:37: error: bitwise comparison always evaluates to false [-Werror=tautological-compare]
This changes it to a simple bit mask operation to check
whether the bit is set.
Fixes: 026abc3332 ("gma500: initial medfield merge")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170905074741.435324-1-arnd@arndb.de
The header comment in include/trace/define_trace.h specifies that the
TRACE_INCLUDE_PATH needs to be relative to the define_trace.h header
rather than the trace file including it. Most instances get that wrong
and work around it by adding the $(src) directory to the include path.
While this works, it is preferable to refer to the correct path to the
trace file in the first place and avoid any workaround.
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170901144954.19620-6-thierry.reding@gmail.com
The header comment in include/trace/define_trace.h specifies that the
TRACE_INCLUDE_PATH needs to be relative to the define_trace.h header
rather than the trace file including it. Most instances get that wrong
and work around it by adding the $(src) directory to the include path.
While this works, it is preferable to refer to the correct path to the
trace file in the first place and avoid any workaround.
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170901144954.19620-3-thierry.reding@gmail.com
The header comment in include/trace/define_trace.h specifies that the
TRACE_INCLUDE_PATH needs to be relative to the define_trace.h header
rather than the trace file including it. Most instances get that wrong
and work around it by adding the $(src) directory to the include path.
While this works, it is preferable to refer to the correct path to the
trace file in the first place and avoid any workaround.
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170901144954.19620-1-thierry.reding@gmail.com
Based on patch "Convert drivers to explicit reset API" from Philipp Zabel
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philippe CORNU <philippe.cornu@st.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1501593788-21036-4-git-send-email-philippe.cornu@st.com
This patch cleans up the Synopsys mipi dsi register list:
- rename registers according to the Synopsys documentation
(1.30 & 1.31)
- fix typos
- re-order registers for a better coherency
Signed-off-by: Philippe CORNU <philippe.cornu@st.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1501593788-21036-3-git-send-email-philippe.cornu@st.com
drm_fb_helper_resume_worker() uses fb_helper->fbdev to call
fb_set_suspend() which dereferences the pointer.
Move sync-canceling of the resume worker in drm_fb_helper_fini() before
setting fb_helper->fbdev to NULL. Move dirty_work as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1503940668-25883-2-git-send-email-noralf@tronnes.org
drm_fb_cma_create() is just a wrapper around drm_gem_fb_create() now,
so use the function directly.
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1502631125-13557-18-git-send-email-noralf@tronnes.org
Reject mapping an imported dma-buf since is's an invalid use-case.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1502986891-36764-2-git-send-email-noralf@tronnes.org
The error messages generated by the SCDC helpers are somewhat
inconsistent with other DRM errors and even with other errors in the
same file. Fix them all up to use a common format.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170901144430.19164-2-thierry.reding@gmail.com
This Fixes build on branches where we already have format-modifier.
Reference: https://lists.freedesktop.org/archives/dri-devel/2017-August/151044.html
Fixes: 179c02fe90 ("drm/tve200: Add new driver for TVE200")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Janet Morgan <janet.morgan@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Daniel Stone <daniels@collabora.com> (v2)
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170825201612.23056-1-rodrigo.vivi@intel.com
drm_fb_cma_create() is just a wrapper around drm_gem_fb_create() now,
so use the function directly.
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1502631125-13557-17-git-send-email-noralf@tronnes.org
This adds a new DRM driver for the Faraday Technology TVE200
block. This "TV Encoder" encodes a ITU-T BT.656 stream and can
be found in the StorLink SL3516 (later Cortina Systems CS3516)
as well as the Grain Media GM8180.
I do not have definitive word from anyone at Faraday that this
IP block is theirs, but it bears the hallmark of their 3-digit
version code (200) and is used in two SoCs from completely
different companies. (Grain Media was fully owned by Faraday
until it was transferred to NovoTek this january, and
Faraday did lots of work on the StorLink SoCs.)
The D-Link DIR-685 uses this in connection with the Ilitek
ILI9322 panel driver that supports BT.656 input, while the
GM8180 apparently has been used with the Cirrus Logic CS4954
digital video encoder. The oldest user seems to be
something called Techwall 2835.
This driver is heavily inspired by Eric Anholt's PL111
driver and therefore I have mentioned all the ancestor authors
in the header file.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170820100557.24991-2-linus.walleij@linaro.org
This is the same bug as we fixed in commit f6cd7daecf ("drm: Release
driver references to handle before making it available again"), but now
the exposure is via the PRIME lookup tables. If we remove the
object/handle from the PRIME lut, then a new request for the same
object/fd will generate a new handle, thus for a short window that
object is known to userspace by two different handles. Fix this by
releasing the driver tracking before PRIME.
Fixes: 0ff926c7d4 ("drm/prime: add exported buffers to current fprivs
imported buffer list (v2)")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170819120558.6465-1-chris@chris-wilson.co.uk
