Removed the use of 'card_type' from the tuner configuration structure, and
replaced it with separate parameters to set board-specific configuration.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is initial code written by Davide Ferri for the PCTV 340e, including
a new xc4000 driver. I am checking in all the code unmodified, and making
no assertions about its quality (other than confirming it compiles).
[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Davide Ferri <davidef1986@gmail.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The implementation of the gain calculation for this sensor is incorrect.
It is only working for the first 127 values.
The reason is, that the gain cannot be set directly by writing a value
into the gain registers of the sensor. The gain register work this way
(see datasheet page 24): bits 0 to 6 are called "initial gain". These
are linear. But bits 7 and 8 ("analog multiplicative factors") and bits
9 and 10 ("digital multiplicative factors") work completely different:
Each of these bits increase the gain by the factor 2. So if the bits
7-10 are 0011, 0110, 1100 or 0101 for example, the gain from bits 0-6 is
multiplied by 4. The order of the bits 7-10 is not important for the
resulting gain. (But there are some recommended values for low noise)
The current driver doesn't do this correctly: If the current gain is 000
0111 1111 (127) and the gain is increased by 1, you would expect the
image to become brighter. But the image is completly dark, because the
new gain is 000 1000 0000 (128). This means: Initial gain of 0,
multiplied by 2. The result is 0.
This patch adds a new function which does the gain calculation and also
fixes the same bug for red_balance and blue_balance. Additionally, the
driver follows the recommendation from the datasheet, which says, that
the gain should always be above 0x0020.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are problems when you use this camera/sensor in a very bright room
or outside. The image is completely white, because it is overexposed.
The driver uses a default value which is not suitable for all
environments.
This patch makes it possible to adjust the exposure time by youself. I
found out by logging the i2c-data, that the windows driver for this
sensor is doing this, too. I tested the camera on a sunny day and after
adjusting the exposure time, I was able to see a very good image.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the datasheet (page 8), the first optical clear
pixel-column is not at position 14. The correct/recommended value is 20.
Without this patch there is a dark line on the left side of the image.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Otherwise they clutter the dmesg buffer even on a production kernel.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On function videobuf_pages_to_sg the statement sg_set_page(&sglist[0],
pages[0], PAGE_SIZE - offset, offset) will fail if size is less than
PAGE_SIZE.
Signed-off-by: Newson Edouard <newsondev@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
list_first_entry() always returns non-null here. I think the intent was
to test whether there were any entries in the used list.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All boards use EM28xxx_BOARD, to identify that the macro
refers to a card entry. So:
EM2874_LEADERSHIP_ISDBT -> EM2874_BOARD_LEADERSHIP_ISDBT
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some reason it repeats rather slowly, around 800ms intervals,
two RC5 remotes tested.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This sensor was found in a webcam 8020:ef04 (SVC - SVU2-1.3MV PCCam).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As Simon reported, digital TV broke with mt20xx tuner due to
commit ad020dc2fe.
The mt20xx tuner passes V4L2_TUNER_DIGITAL_TV to tuner core. However, the
check_mode code now doesn't handle it well. Change the logic there to
avoid the breakage, and fix a test for analog-only at g_tuner.
Reported-by: Simon Arlott <simon@fire.lp0.eu>
Tested-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit e38030f3ff.
MSI flat-out doesn't work right on cx2388x devices yet. There are now
multiple reports of cards that hard-lock systems when MSI is enabled,
including my own HVR-1250 when trying to use its built-in IR receiver.
Disable MSI and it works just fine. Similar for another user's HVR-1270.
Issues have also been reported with the HVR-1850 when MSI is enabled,
and the 1850 behavior sounds similar to an as-yet-undiagnosed issue I've
seen with an 1800.
CC: stable@kernel.org
CC: Steven Toth <stoth@kernellabs.com>
CC: Kusanagi Kouichi <slash@ac.auone-net.jp>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] msp3400: fill in v4l2_tuner based on vt->type field
[media] tuner-core.c: don't change type field in g_tuner or g_frequency
[media] cx18/ivtv: fix g_tuner support
[media] tuner-core: power up tuner when called with s_power(1)
[media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
[media] tuner-core: simplify the standard fixup
[media] tuner-core/v4l2-subdev: document that the type field has to be filled in
[media] v4l2-subdev.h: remove unused s_mode tuner op
[media] feature-removal-schedule: change in how radio device nodes are handled
[media] bttv: fix s_tuner for radio
[media] pvrusb2: fix g/s_tuner support
[media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
[media] tuner-core: fix tuner_resume: use t->mode instead of t->type
[media] tuner-core: fix s_std and s_tuner
The vt->type field determines how the msp3400 should fill in the
tuner data, not whether the msp3400 is in radio mode or not.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner core should not silently change the type field in g_tuner and
g_frequency. If the tuner is in a different mode than the one that was
requested, then just fill in what you can and don't attempt to read afc,
signal or rxsubchans values.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver shouldn't override vt->type, and the tuner name should be
based on vt->type as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers must be able to rely on s_power to power up subdevices.
Note that at this moment no driver attempts to power up tuners. This probably
isn't surprising since s_power(1) was never implemented in tuner-core.c until
now.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prohibit attempts to change the tuner to a type that is different
from the device node the ioctl is called from. I.e. the type must
be RADIO for a radio node and ANALOG_TV for a video/vbi node.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of a number of unnecessary tuner_dbg messages by simplifying
the std fixup function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner ops g_frequency, g_tuner and s_tuner require that the tuner type
field is filled in. Document this.
The tuner-core doc is based on a patch from Mauro Carvalho Chehab <mchehab@redhat.com>.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix typo: g_tuner should have been s_tuner.
Tested with a bttv card.
Cc: stable@kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner-core subdev requires that the type field of v4l2_tuner is
filled in correctly. This is done in v4l2-ioctl.c, but pvrusb2 doesn't
use that yet, so we have to do it manually based on whether the current
input is radio or not.
Tested with my pvrusb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Mike Isely <isely@pobox.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The subdevs are supposed to receive a valid tuner type for the g_frequency
and g/s_tuner subdev ops. Some drivers do this, others don't. So prefill
this in v4l2-ioctl.c based on whether the device node from which this is
called is a radio node or not.
The spec does not require applications to fill in the type, and if they
leave it at 0 then the 'check_mode' call in tuner-core.c will return
an error and the ioctl does nothing.
Cc: stable@kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
set_mode is called with t->type, which is the tuner type. Instead, use
t->mode which is the actual tuner mode (i.e. radio vs tv).
Cc: stable@kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both s_std and s_tuner are broken because set_mode_freq is called before the
new std (for s_std) and audmode (for s_tuner) are set.
This patch splits set_mode_freq in a set_mode and a set_freq and in s_std/s_tuner
first calls set_mode, and if that returns 0 (i.e. the mode is supported)
then they set t->std/t->audmode and call set_freq.
This fixes a bug where changing std or audmode would actually change it to
the previous value.
Discovered while testing analog TV standards for cx18 with a tda18271 tuner.
Cc: stable@kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (46 commits)
[media] rc: call input_sync after scancode reports
[media] imon: allow either proto on unknown 0xffdc
[media] imon: auto-config ffdc 7e device
[media] saa7134: fix raw IR timeout value
[media] rc: fix ghost keypresses with certain hw
[media] [staging] lirc_serial: allocate irq at init time
[media] lirc_zilog: fix spinning rx thread
[media] keymaps: fix table for pinnacle pctv hd devices
[media] ite-cir: 8709 needs to use pnp resource 2
[media] V4L: mx1-camera: fix uninitialized variable
[media] omap_vout: Added check in reqbuf & mmap for buf_size allocation
[media] OMAP_VOUT: Change hardcoded device node number to -1
[media] OMAP_VOUTLIB: Fix wrong resizer calculation
[media] uvcvideo: Disable the queue when failing to start
[media] uvcvideo: Remove buffers from the queues when freeing
[media] uvcvideo: Ignore entities for terminals with no supported format
[media] v4l: Don't access media entity after is has been destroyed
[media] media: omap3isp: fix a potential NULL deref
[media] media: vb2: fix allocation failure check
[media] media: vb2: reset queued_count value during queue reinitialization
...
Fix up trivial conflict in MAINTAINERS as per Mauro
The comment says "wait 15ms", but the code says jiffies_to_msecs(15)
instead of msecs_to_jiffies(15). Fix that. Tested, works fine with both
rc5 and rc6 decode, in-kernel and via lirc userspace, with an HVR-1150.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mx1_camera_add_device() can return an uninitialized value of ret.
Signed-off-by: Andre Bartke <andre.bartke@gmail.com>
[g.liakhovetski@gmx.de: modified the fix to remove "ret" completely]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The usecase where, user allocates small size of buffer
through bootargs (video1_bufsize/video2_bufsize) and later from application
tries to set the format which requires larger buffer size, driver doesn't
check for insufficient buffer size and allows application to map extra buffer.
This leads to kernel crash, when user application tries to access memory
beyond the allocation size.
Added check in both mmap and reqbuf call back function,
and return error if the size of the buffer allocated by user through
bootargs is less than the S_FMT size.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With addition of media-controller framework, now we have various
device nodes (/dev/videoX) getting created, so hardcoding
minor number in video_register_device() is not recommended.
So let V4L2 framework choose free minor number for the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The omap_vout_new_crop() function has possible bug, uses uninitialized
variable "crop.width/height" which is actually output of the function.
Instead we should be using "try_crop.width/height" to calculate the
resizer value.
Signed-off-by: Vladimir Pantelic <vladoman@gmail.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When failing to start the camera we should disable the queue again, to
rollback into the same initial state. Otherwise re-trying will always
hit -EBUSY
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When freeing memory for the video buffers also remove them from the
irq & main queues.
This fixes an oops when doing the following:
open ("/dev/video", ..)
VIDIOC_REQBUFS
VIDIOC_QBUF
VIDIOC_REQBUFS
close ()
As the second VIDIOC_REQBUFS will cause the list entries of the buffers
to be cleared while they still hang around on the main and irc queues
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If a streaming interface has no supported format, the driver won't
create a video device for the associated terminal. Fix an oops by
ignoring that terminal when creating links between entities.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Entities associated with video device nodes are unregistered in
video_unregister_device(). This destroys the entity even though it can
still be accessed through open video device nodes.
Move the media_device_unregister_entity() call from
video_unregister_device() to v4l2_device_release() to ensure that the
entity isn't unregistered until the last reference to the video device
is released.
Also remove the media_entity_get()/put() calls from v4l2-dev.c. Those
functions were designed for subdevs, to avoid a parent module from being
removed while still accessible through board code. They're not currently
needed for video device nodes, and will oops when a hotpluggable device
is disconnected during streaming, as media_entity_put() called in
v4l2_device_release() tries to access entity->parent->dev->driver which
is set to NULL when the device is disconnected.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a potential NULL pointer dereference by skipping registration of
external entities in case none are provided.
This is useful at least when testing mere memory-to-memory scenarios.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
__vb2_queue_alloc function returns the number of successfully allocated
buffers. There is no point in checking if the returned value is negative.
If this function returns 0, videobuf2 should just return -ENOMEM to
userspace, because no driver can work without memory buffers.
Reported-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
queued_count variable was left untouched during the queue reinitialization
in __vb2_queue_cancel, what might lead to mismatch between the real number
of queued buffers and queued_count variable.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 31901a078a.
Queue should be reinitialized on each REQBUFS() call even if the memory
access method and buffer count have not been changed. The user might have
changed the format and if we go the short path introduced in that commit,
the memory buffer will not be reallocated to fit with new format.
The previous patch was just over-engineered optimization, which just
introduced a bug to videobuf2.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add __GFP_NOWARN parameter to videobuf2 dma-sg allocator to prevent
kernel warning and stack dump if there is not enough memory available.
Videobuf2 and drivers should correctly handle no memory case, so there
is no need for stack dump and extensive log.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Unplugging a pwc cam while an app has the /dev/video# node open leads
to an oops in pwc_video_close when the app closes the node, because
the disconnect handler has free-ed the pdev struct pwc_video_close
tries to use. Instead of adding some sort of bandaid for this.
fix it properly using the v4l2 core's new(ish) behavior of keeping the
v4l2_dev structure around until both unregister has been called, and
all file handles referring to it have been closed:
Embed the v4l2_dev structure in the pdev structure and define a v4l2 dev
release callback releasing the pdev structure (and thus also the embedded
v4l2 dev structure.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove union version in the m5mols_get_version(), and read version information
directly. Also remove VERSION_SIZE.
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For now, the m5mols_read() share in case of I2C packet 1, 2, 4 byte(s) width.
So, this commit adds 3 functions - m5mols_read_u8/u16/u32() according to byte
width of I2C packet. And, the u32 variables in spite of u8 or u16 for fitting
to m5mols_read() having no choice, is replaced to have original byte width
like u8, u16, u32 as same reason.
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The main capture and the thumbnail image size registers were
erroneously defined to have 1 byte width, resulting in wrong
reported image size. Fix this by changing the registers width
to correct value.
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With multi-planar formats fmt.pix_mp member of struct v4l2_format
should be used rather than fmt.pix. Fix find_fmt() function to do
the right thing.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The buf_init buffer queue operation is optional and
buffer_init() does nothing, remove it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Avoid dereferencing of NULL f->fmt. Correct size of the allocated
buffer in case the crop rectangle is smaller than the bounds
rectangle (configured with S_FMT). Also remove redundant check
for *num_buffer == 0 as this case is handled in videobuf2.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
staging: iio: max517: Fix iio_info changes
Staging: mei: fix debug code
Staging: cx23885: fix include of altera.h
staging: iio: error case memory leak fix
staging: ath6kl: Fix a kernel panic during suspend/resume
staging: gma500: get control from firmware framebuffer if conflicts
staging: gma500: Skip bogus LVDS VBT mode and check for LVDS before adding backlight
staging: usbip: bugfix prevent driver unbind
staging: iio: industrialio-trigger: set iio_poll_func private_data
staging: rts_pstor: use bitwise operator instead of logical one
staging: fix ath6kl build when CFG80211 is not enabled
staging: brcm80211: fix for 'multiple definition of wl_msg_level' build err
staging: fix olpc_dcon build, needs BACKLIGHT_CLASS_DEVICE
Staging: remove STAGING_EXCLUDE_BUILD option
Staging: altera: move .h file to proper place
The cx23885 driver was including staging/altera.h, but that file has
moved back into the driver directory.
Why a non-staging driver was including a staging driver is beyond me,
but this fixes the build so everything is happy for now.
For the record, it's not ok for a non-staging driver to depend on a
staging one, as that implies that the non-staging one should also be in
the staging tree if that's needed.
Cc: Igor M. Liplianin <liplianin@netup.ru>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/media/video/soc_camera.c: In function ‘soc_camera_video_start’:
drivers/media/video/soc_camera.c:1515: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/uvc/uvc_entity.c: In function ‘uvc_mc_register_entities’:
drivers/media/video/uvc/uvc_entity.c:33: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Internally separates the setting of the broadcast standard for the encoder &
decoder. Externally there's no change in functionality.
[awalls@md.metrocast.net: Edited to fix a checkpatch gripe about multiple
assignment and to remove a now unused DEFINE_WAIT() due to this patch]
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add sanity check to ivtvfb_pan_display() to ensure only valid values are used
to pan the display. Invalid values are rejected with -EINVAL
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it. Also use the
aligned fix.line_length and not the (possible) unaligned xres_virtual.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Two ivtv_msleep_timeout() calls are incorrectly flagged as interruptable. The
first is in the init sequence for a capture and is required for stable
hardware setup. The second is at the end of the capture and used to handle the
last data transfer. Failure to wait for this last transfer can result in stale
data being read at the start of the next capture.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The frame rate variable was not initialized, so, the lowest frame rate was
used for most webcams.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many users said that the default gain value (128) was giving white images.
The value which was in the original qc-usb driver (50) is better.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This file is replaced by autogain_functions.h.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'normal' bulk transfer size did not work for 800x600.
By git commit c42cedbb65, this 'normal' size was used for 1600x1200 only.
It will now be used back again for all resolutions but 800x600.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By git commit c42cedbb65, the bulk transfer size was changed to a lower
value for resolutions != 1600x1200, but the image extraction routine still
worked with the previous value, giving bad truncated images.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] v1.88 DM04/QQBOX Move remote to use rc_core dvb-usb-remote
[media] Add missing include guard to header file
[media] Inlined functions should be static
[media] Remove invalid parameter description
[media] cpia2: fix warning about invalid trigraph sequence
[media] s5p-csis: Add missing dependency on PLAT_S5P
[media] gspca/kinect: wrap gspca_debug with GSPCA_DEBUG
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function
[media] uvcvideo: Connect video devices to media entities
[media] uvcvideo: Register subdevices for each entity
[media] uvcvideo: Register a v4l2_device
[media] add V4L2-PIX-FMT-SRGGB12 & friends to docbook
[media] Documentation/DocBook: Rename media fops xml files
[media] Media DocBook: fix validation errors
[media] wl12xx: g_volatile_ctrl fix: wrong field set
[media] fix kconfig dependency warning for VIDEO_TIMBERDALE
[media] dm1105: GPIO handling added, I2C on GPIO added, LNB control through GPIO reworked
[media] Add support for M-5MOLS 8 Mega Pixel camera ISP
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
gfs2: Drop __TIME__ usage
isdn/diva: Drop __TIME__ usage
atm: Drop __TIME__ usage
dlm: Drop __TIME__ usage
wan/pc300: Drop __TIME__ usage
parport: Drop __TIME__ usage
hdlcdrv: Drop __TIME__ usage
baycom: Drop __TIME__ usage
pmcraid: Drop __DATE__ usage
edac: Drop __DATE__ usage
rio: Drop __DATE__ usage
scsi/wd33c93: Drop __TIME__ usage
scsi/in2000: Drop __TIME__ usage
aacraid: Drop __TIME__ usage
media/cx231xx: Drop __TIME__ usage
media/radio-maxiradio: Drop __TIME__ usage
nozomi: Drop __TIME__ usage
cyclades: Drop __TIME__ usage
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
s5p-csis is to be built only on S5P SoC platforms.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes media_build, and presumably certain other upstream kernel build
option combos.
Before:
CC [M] /home/jarod/src/media_build/v4l/kinect.o
/home/jarod/src/media_build/v4l/kinect.c:38:19: error: 'D_ERR' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:27: error: 'D_PROBE' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:37: error: 'D_CONF' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:46: error: 'D_STREAM' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:57: error: 'D_FRAM' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:38:66: error: 'D_PACK' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:39:2: error: 'D_USBI' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:39:11: error: 'D_USBO' undeclared here (not in a function)
/home/jarod/src/media_build/v4l/kinect.c:39:20: error: 'D_V4L2' undeclared here (not in a function)
make[3]: *** [/home/jarod/src/media_build/v4l/kinect.o] Error 1
After:
CC [M] /home/jarod/src/media_build/v4l/kinect.o
...
LD [M] /home/jarod/src/media_build/v4l/gspca_kinect.ko
...
profit
Reported-by: Nicolas Will <nico@youplala.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video devices associated to USB streaming terminals must be
connected to their associated terminal's media entity instead of being
standalone entities.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Userspace applications can now discover the UVC device topology using
the media controller API.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a first step to the media controller integration register a
v4l2_device for each UVC control interface and make the video_device a
child of the v4l2_device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (247 commits)
[media] gspca - sunplus: Fix some warnings and simplify code
[media] gspca: Fix some warnings tied to 'no debug'
[media] gspca: Unset debug by default
[media] gspca - cpia1: Remove a bad conditional compilation instruction
[media] gspca - main: Remove USB traces
[media] gspca - main: Version change to 2.13
[media] gspca - stk014 / t613: Accept the index 0 in querymenu
[media] gspca - kinect: Remove __devinitdata
[media] gspca - cpia1: Fix some warnings
[media] video/Kconfig: Fix mis-classified devices
[media] support for medion dvb stick 1660:1921
[media] tm6000: fix uninitialized field, change prink to dprintk
[media] cx231xx: Add support for Iconbit U100
[media] saa7134 add new TV cards
[media] Use a more consistent value for RC repeat period
[media] cx18: Move spinlock and vb_type initialisation into stream_init
[media] tm6000: remove tm6010 sif audio start and stop
[media] tm6000: remove unused exports
[media] tm6000: add pts logging
[media] tm6000: change from ioctl to unlocked_ioctl
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
This patch removes warnings due to GSPCA_DEBUG unsetting. It implied
a simplification of the code.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the warnings raised by unsetting the option GSPCA_DEBUG.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The output of possible hardware or software errors does not depend on the
option GSPCA_DEBUG. This one is useful only when working on the main driver
or on a subdriver (bug fix, enhancement, new webcam/bridge/sensor or bug fix).
It is enabled in the gspca test version which is available from my web site.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a compilation error when GSPCA_DEBUG is not set.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The USB traces are better done by usbmon which is enabled in most Linux/GNU
distributions and which permits easier comparison with the USB exchanges of
other drivers.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
__devinit* must not be used in USB drivers.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The helper chips are classified by their function. Unfortunaltely,
with time, developers added their stuff into the wrong places.
Fix it by moving itens to be at the right place. Also add a new
category for sensors and for misc devices that are found only on
a certain specific board.
While here, fix two bad whitespaces at Kconfig.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the "Iconbit Analog Stick U100 FM".
Only composite & s-video inputs, no tuner support now.
Signed-off-by: Igor Novgorodov <igor@novg.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new TV cards of Beholder Company. Just for autodetect.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initialisation of vb_type in serialized_open was preventing
REQBUFS from working reliably. Remove it, and move the spinlock into
stream_init for good measure - it's only used when we have a stream
that supports videobuf anyway.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure pdev is not dereferenced when it is null
Signed-off-by: Huzaifa Sidhpurwala <huzaifas@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable the IR support for the Hauppauge HVR-1150 and HVR-1120.
Thanks to Fernando Laudares Camargos for testing the patch.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Fernando Laudares Camargos <fernando.laudares.camargos@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The M420 format is used by the Microsoft LifeCam Studio HD.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[laurent.pinchart@ideasonboard.com: split into v4l/uvcvideo patches]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support to uvc driver for NOMMU arch including add function
uvc_queue_get_unmapped_area() and make some changes in uvc_queue_mmap().
So that uvc camera can be used on nommu arch like blackfin.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This camera driver supports only rising edge, which is the default
setting of the device. The function mt9m111_setup_pixfmt() overwrites
this setting. So the driver actually uses falling edge.
This patch corrects that.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
[g.liakhovetski@gmx.de: removed superfluous register write]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The setup of the pixel clock is done wrong in the mt9v022 driver.
The 'Invert Pixel Clock' bit has to be set to 1 for falling edge
and not for rising. This is not clearly described in the data
sheet.
Tested on pcm037 and pcm027/pcm990.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc_mbus_get_fmtdesc() returning NULL means only, that no standard
mediabus code -> fourcc conversion is known, this shouldn't be treated
as an error by drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new look-up entries for all mediabus codes, for which respective
fourcc codes exist.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
12-bit formats, similar to YUV 4:2:0 occupy 3 bytes for each two pixels
and cannot be described by any of the existing SOC_MBUS_PACKING_* macros.
This patch adds a new one SOC_MBUS_PACKING_1_5X8 to describe such
formats and extends soc_mbus_samples_per_pixel() to support it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since V4L2_MBUS_FMT_* codes have become large and sparse, they cannot
be used as array indices anymore.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Recently mediabus pixel format codes have become a part of the user-
space API, at which time their values also have been changed from
contiguous numbers, running from 0 to sparse numbers with values
around 0x1000, 0x2000, 0x3000... This made them unsuitable for the
use as array indices. This patch switches soc-camera internal format
look-ups to not depend on values of those macros.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an soc-camera host livecrop operation to implement live zoom. If
a host driver implements it, it should take care to preserve output
frame format, then live crop doesn't break streaming.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The .stop_streaming() videobuf2 operation has to be implemented to
guarantee, that video buffers are not written to after a STREAMOFF.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The .stop_streaming() videobuf2 operation has to be implemented to
guarantee, that video buffers are not written to after a STREAMOFF.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the subdev driver for the MIPI CSIS units available in S5P and
Exynos4 SoC series. This driver supports both CSIS0 and CSIS1
MIPI-CSI2 receivers.
The driver requires Runtime PM to be enabled for proper operation.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s5p-fimc now also implements a camera capture video node so move
it under the "Video capture devices" Kconfig menu. Also update
the entry to reflect the driver's coverage of EXYNOS4 SoCs and
separate the Makefile entry from the soc-camera drivers set.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the expression "video stream" instead of "color camera" which is
more correct as the driver supports the RGB and IR image on the same
endpoint.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move large communications buffers out of stack and into device
structure. This prevents the frame size from being >1kB and fixes a
compiler warning when CONFIG_FRAME_WARN=1024:
drivers/media/video/gspca/kinect.c: In function ‘send_cmd.clone.0’:
drivers/media/video/gspca/kinect.c:202: warning: the frame size of 1548 bytes is larger than 1024 bytes
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Drew Fisher <drew.m.fisher@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes autoloading of the module.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I misused the ktime API, and failed to remove some traces of the
in-kernel format conversion. Fix these, so the the driver builds
without warnings.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the public API definitions to include/linux/uvcvideo.h and bump the
version number to 1.1.0. Compatibility with the old API is kept,
application can still be compiled against the private header and will
not break.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of passing the value down to the device and getting an error
back (or worse, crashing the firmware), return -ERANGE when the
requested menu entry is not supported.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Supported menu entries are reported by the device in response to the
GET_RES query. Use the information to return -EINVAL to userspace for
unsupported values when enumerating menu entries.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set the FIX_BANDWIDTH quirk for the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the PROBE_MINMAX quirk. Add a corresponding entry
in the device IDs list
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The TomTom navigation system used in the Sony XNV 660BT and 770BT
reports an RGB565 (RGBP) format, support it in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes the public driver API more uniform, in preparation of moving
uvcvideo.h to include/linux. Keep the old names for backward
compatibility with existing applications.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those ioctls are deprecated, list them in the features removal schedule
for 2.6.42.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl extends UVCIOC_CTRL_GET/SET by not only allowing to get/set
XU controls but to also send arbitrary UVC commands to XU controls,
namely GET_CUR, SET_CUR, GET_MIN, GET_MAX, GET_RES, GET_LEN, GET_INFO
and GET_DEF. This is required for applications to work with XU controls,
so that they can properly query the size and allocate the necessary
buffers.
Signed-off-by: Martin Rubli <martin_rubli@logitech.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To simplify maintainer support of this driver, bump the version to
1.5.0 - this will be the first version that is expected to support
mmap() for raw video frames.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial version of this patch (commit
d5976931639176bb6777755d96b9f8d959f79e9e) had some issues:
* It didn't correctly calculate the size of the YUV buffer for 4:2:2,
resulting in capture sometimes being offset by 1/3rd of a picture.
* There were a lot of variables duplicating information the driver
already knew, which have been removed.
* There was an in-kernel format conversion - libv4l can do this one,
and is the right place to do format conversions anyway.
* Some magic numbers weren't properly explained.
Fix all these issues, leaving just the move from videobuf to videobuf2
to do.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently 'fh' initialises to whatever happens to be on stack. This
looks like a typo and this patch fixes that.
Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
EM28174 is very similar as already supported EM2874.
I am not sure what are differences, but it could be analog support.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register multiple FEs for same adapter. After that it is
possible to register two FEs for same adapter. For example
one for DVB-T and one for DVB-C.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently video capturing using streaming I/O method
doesn't work if capturing to overlay buffer took place
before.
When enabling the stream we have to check the overlay
enable driver flag and reset it so that the interrupt
handler won't execute the overlay interrupt path after
enabling DMA in streamon routine. Otherwise the capture
interrupt won't be handled correctly causing non working
VIDIOC_DQBUF ioctl.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently the driver enables overlay when running
VIDIOC_S_FMT ioctl with fmt type V4L2_BUF_TYPE_VIDEO_OVERLAY.
Actually, this is wrong. Add proper VIDIOC_OVERLAY support
instead of using VIDIOC_S_FMT for overlay enable.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_altnum_to_altsetting() may return NULL. If it does we'll dereference a
NULL pointer in
drivers/media/video/gspca/stv06xx/stv06xx_pb0100.c::pb0100_start().
As far as I can tell there's not really anything more sensible than
-ENODEV that we can return in that situation, but I'm not at all intimate
with this code so I'd like a bit of review/comments on this before it's
applied.
Anyway, here's a proposed patch.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Erik Andren <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MT9V032 is a parallel wide VGA sensor from Aptina (formerly Micron)
controlled through I2C.
The driver creates a V4L2 subdevice. It currently supports binning and
cropping, and the gain, auto gain, exposure, auto exposure and test
pattern controls.
Signed-off-by: Detlev Casanova <detlev.casanova@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the core-assisted locking in fsl-viu driver and switch
to .unlocked_ioctl.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
users is always read or written with core->lock held. A plain int is
simpler and faster.
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mpeg_users is always read or written with core->lock held except
in mpeg_release (where it looks like a bug). A plain int is simpler
and faster.
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It should not be possible to enter mpeg_open and acquire core->lock
without the blackbird driver being registered, so just error out if it
is not. This makes the code more readable and should prevent the bug
fixed by the patch "hold device lock during sub-driver initialization"
from resurfacing again.
Similarly, if we enter mpeg_release and acquire core->lock then either
the blackbird driver is registered (since open files keep it loaded)
or the sysadmin forced the driver's removal. In the latter case the
state will be inconsistent and this is worth a loud warning.
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add and use a mutex to protect the cx88-mpeg device list. Previously
the BKL prevented races.
Based on work by Ben Hutchings <ben@decadent.org.uk>.
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx8802_blackbird_probe makes a device node for the mpeg sub-device
before it has been added to dev->drvlist. If the device is opened
during that time, the open succeeds but request_acquire cannot be
called, so the reference count remains zero. Later, when the device
is closed, the reference count becomes negative --- uh oh.
Close the race by holding core->lock during probe and not releasing
until the device is in drvlist and initialization finished.
Previously the BKL prevented this race.
Reported-by: Andreas Huber <hobrom@gmx.at>
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Cc: stable@kernel.org
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The BKL conversion of this driver seems to have gone wrong.
Loading the cx88-blackbird driver deadlocks.
The cause: mpeg_ops::open in the cx2388x blackbird driver acquires the
device lock and calls the sub-driver's request_acquire, which tries to
acquire the lock again. Fix it by clarifying the semantics of
request_acquire, request_release, advise_acquire, and advise_release:
now all will rely on the caller to acquire the device lock.
Based on work by Ben Hutchings <ben@decadent.org.uk>.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=31962
Reported-by: Andi Huber <hobrom@gmx.at>
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Cc: stable@kernel.org
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The BKL conversion of this driver seems to have gone wrong. Various
uses of the sub-device and driver lists appear to be subject to race
conditions.
In particular, some functions access drvlist without a relevant lock
held, which will race against removal of drivers. Let's start with
that --- clean up by consistently protecting dev->drvlist with
dev->core->lock, noting driver functions that require the device lock
to be held or not to be held.
After this patch, there are still some races --- e.g.,
cx8802_blackbird_remove can run between the time the blackbird driver
is acquired and the time it is used in mpeg_release, and there's a
similar race in cx88_dvb_bus_ctrl. Later patches will address the
remaining known races and the deadlock noticed by Andi. This patch
just makes the semantics clearer in preparation for those later
changes.
Based on work by Ben Hutchings <ben@decadent.org.uk>.
Tested-by: Andi Huber <hobrom@gmx.at>
Tested-by: Marlon de Boer <marlon@hyves.nl>
Cc: stable@kernel.org
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enabling force_testpattern module parameter in usbvision causes kernel panic.
Things like that does not belong to the kernel anyway so the fix is easy.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add Nogatech USB MicroCam PAL (NV3001P) and NTSC (NV3000N) support to
usbvision driver.
PAL version is tested, NTSC untested.
Data captured using usbsnoop, init_values are listed in the INF file along
with image dimensions, offsets and frame rates.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We leak the memory allocated to 'fw' (the firmware) when the variable goes
out of scope.
Fix the leak by calling release_firmware(fw) before 'fw' goes out of
scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for mmap method streaming of raw YUV video on cx18-based
hardware, in addition to the existing support for read() streaming of
raw YUV and MPEG-2 encoded video.
[simon.farnsworth@onelan.co.uk: I forward-ported this from Steven's original work,
done under contract to ONELAN. The original code is at
http://www.kernellabs.com/hg/~stoth/cx18-videobuf]
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
An usb_submit_urb should be atomic in a completion handler. This fixes
"BUG: scheduling while atomic" messages.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The generic_standards_cnt define is only used in one place and it's
more readable to just call ARRAY_SIZE(generic_standards) directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function returns NULL on failure so lets do that if kzalloc()
fails. There is a separate problem that the caller for this function
doesn't check for errors...
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-By: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This card has a TD18271 silicon tuner, and uses TDA8290 and LGS8G75 to
demodulate analog and digital broadcast respectively. GPIO configurations
were derived using DScaler regspy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ability to force the encoder or decoder chip was broken by commit
0ab6e1c38d in February 2009. As nobody
complained for over 2 years, I take it that these parameters were no
longer used so we can simply drop them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Kinect sensor is a device used by Microsoft for its Kinect project,
which is a system for controller-less Human-Computer interaction
targeted for Xbox 360.
In the Kinect device, RGBD data is captured from two distinct sensors: a
regular RGB sensor and a monochrome sensor which, with the aid of a IR
structured light, captures what is finally exposed as a depth map; so
what we have is basically a Structured-light 3D scanner.
The Kinect gspca subdriver just supports the video stream for now,
exposing the output from the RGB sensor or the unprocessed output from
the monochrome sensor; it does not deal with the processed depth stream
yet, but it allows using the sensor as a Webcam or as an IR camera (an
external source of IR light might be needed for this use).
The low level implementation is based on code from the OpenKinect
project (http://openkinect.org).
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make a user visible driver version change, for the inevitable user support
questions about why newer model HVR-1600's do not work with (older
versions of) the cx18 driver.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A previous changes which added the newer model HVR-1600's and DTV support for
them, neglected to add RF analog TV for them. Fix RF analog TV for the newer
HVR-1600's which have a worldwide analog tuner assembly with a TDA18271 tuner
and TDA8295 demodulator.
Thanks go to Jeff Campbell and Mike Bradley for reproting the problem, and
also to Mike Bradley for doing a lot of the legwork to figure out the tuner
reset GPIO line, the demodulator I2C address, and that the GPIOs have to be
reinitialized after a cardtype switch.
Reported-by: Jeff Campbell <jac1dlists@gmail.com>
Tested-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the PCTV 330e remote control
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the flag indicating the 330e board is not validated, based on the half
dozen users who have reported today that everything is working.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the calls necessary to use the new drx-d driver for the PCTV 330e
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Given how PCTV has multiple products with the same model name, include the
model number in the description and #define to make it a little more clear.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx bridge strobes the reset pin on the drx-d on every ts_ctrl call.
This results in the state of the chip getting out of the sync with the
state of the driver (and hence all tuning requests after the first one fail).
Make sure the drx-d is not being held in reset, but don't actually perform a
hardware reset on the chip.
The GPIO block has been split out from the other HVR-9x0 variants to reduce
the risk of regression, although in theory they would not have any issues
since none of those cases have the frontend driver managing any internal
state.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the tuner is not actually behind an i2c gate, using the i2c gate control
function can wedge the i2c bus. Provide the ability to control on a per-board
basis whether it should be used.
Problem was noticed on the HVR-900 R2, where it resulted in the first tuning
attempt succeeding, and then all subsequent attempts to access the xc3028
being treated as failures (including the call to sleep the tuner).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pci_setup_device() has saved the PCI revision in the pci_dev
struct since Linux 2.6.23. Use it.
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] ngene: Fix CI data transfer regression Fix CI data transfer regression introduced by previous cleanup.
[media] v4l: make sure drivers supply a zeroed struct v4l2_subdev
[media] Missing frontend config for LME DM04/QQBOX
[media] rc_core: avoid kernel oops when rmmod saa7134
[media] imon: add conditional locking in change_protocol
[media] rc: show RC_TYPE_OTHER in sysfs
[media] ite-cir: modular build on ppc requires delay.h include
[media] mceusb: add Dell transceiver ID
A recent patch has given individual soc-camera host drivers a possibility
to calculate .sizeimage and .bytesperline pixel format fields internally,
however, some drivers relied on the core calculating these values for
them, following a default algorithm. This patch restores the default
calculation for such drivers.
Based on initial patch by Guennadi Liakhovetski, found here:
http://www.spinics.net/lists/linux-media/msg31282.html
Except that this covers try_fmt aswell.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2_subdev_* functions are meant for older V4L2 drivers that do not use
the control framework yet. These functions should not be used by subdev_do_ioctl.
Most of those backwards compatibility functions are just stubs, but commit
87a0c94ce6 actually changed the behavior of
v4l2_subdev_queryctrl, so calling that one from subdev_do_ioctl broke the
control enumeration in subdev nodes.
The fix is simply not to use those compatibility functions in v4l2-subdev.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the IR interrupt handler of cx88-input.c there's a 32-bit multiply
overflow which causes IR pulse durations to be incorrectly calculated.
This is a regression caused by commit 2997137be8.
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If v4l2_device_register_subdev() fails, the reference to the subdev
module taken by the function isn't released. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some v4l drivers currently don't initialize their struct v4l2_subdev
with zeros, and this is a problem since some of the v4l2 code expects
this. One example is the addition of internal_ops in commit 45f6f84,
after that we are at risk of random oopses with these drivers when code
in v4l2_device_register_subdev tries to dereference sd->internal_ops->*,
as can be shown by the report at http://bugs.launchpad.net/bugs/745213
and analysis of its crash at https://lkml.org/lkml/2011/4/1/168
Use kzalloc within problematic drivers to ensure we have a zeroed struct
v4l2_subdev.
BugLink: http://bugs.launchpad.net/bugs/745213
Cc: <stable@kernel.org>
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (42 commits)
[media] media: vb2: correct queue initialization order
[media] media: vb2: fix incorrect v4l2_buffer->flags handling
[media] s5p-fimc: Add support for the buffer timestamps and sequence
[media] s5p-fimc: Fix bytesperline and plane payload setup
[media] s5p-fimc: Do not allow changing format after REQBUFS
[media] s5p-fimc: Fix FIMC3 pixel limits on Exynos4
[media] tda18271: update tda18271c2_rf_cal as per NXP's rev.04 datasheet
[media] tda18271: update tda18271_rf_band as per NXP's rev.04 datasheet
[media] tda18271: fix bad calculation of main post divider byte
[media] tda18271: prog_cal and prog_tab variables should be s32, not u8
[media] tda18271: fix calculation bug in tda18271_rf_tracking_filters_init
[media] omap3isp: queue: Don't corrupt buf->npages when get_user_pages() fails
[media] v4l: Don't register media entities for subdev device nodes
[media] omap3isp: Don't increment node entity use count when poweron fails
[media] omap3isp: lane shifter support
[media] omap3isp: ccdc: support Y10/12, 8-bit bayer fmts
[media] media: add missing 8-bit bayer formats and Y12
[media] v4l: add V4L2_PIX_FMT_Y12 format
cx23885: Fix stv0367 Kconfig dependency
[media] omap3isp: Use isp xclk defines
...
Fix up trivial conflict (spelink errurs) in drivers/media/video/omap3isp/isp.c
Using C line continuation inside format strings is error prone.
Clean up the unintended whitespace introduced by misuse of \.
Neaten correctly used line continations as well for consistency.
drivers/scsi/arcmsr/arcmsr_hba.c has these errors as well,
but arcmsr needs a lot more work and the driver should likely be
moved to staging instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
