Orange Pi Zero board has a SY8113B regulator, which is controlled via
GPIO and capable of outputing 1.1V when the PL6 GPIO is set to output 0
or 1.3V when the PL6 GPIO is set to input or output 1, and the output is
the power supply of the ARM cores in H2+ SoC.
Add the device tree node of this regulator and set the cpu's cpu-supply
property to it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
[wens@csie.org: rename regulator node name and label]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The mmc1_pins node with bias-pull-up attribute is already defined in
the sunxi-h3-h5.dtsi file. Thus, we can remove it from here.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There is only one pinctrl configuration for mmc0 and mmc1 so let's
drop the _a suffix from both of them.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Most of the boards use the mmc1 pins and their attributes defined in
mmc1_pins_a. Let's default to that by moving the pinctrl attributes to
the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Most of the boards use the mmc0 pins and their attributes defined in
mmc0_pins_a. Let's default to those by moving the pinctrl attributes
to the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore all boards DT about dwmac-sun8i
This reverts partially commit fe45174b72 ("arm: dts: sunxi: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This tag is about bringing the EMAC support to the H3 boards.
-----BEGIN PGP SIGNATURE-----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=1g1O
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-h3-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3 changes for 4.13
This tag is about bringing the EMAC support to the H3 boards.
* tag 'sunxi-dt-h3-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sun8i: h3: Enable EMAC with external PHY on Orange Pi Plus 2E
arm: sun8i: orangepi-zero: Enable dwmac-sun8i
ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i
ARM: sun8i: orangepi-plus: Enable dwmac-sun8i
arm: sun8i: nanopi-neo: Enable dwmac-sun8i
arm: sun8i: orangepi-pc-plus: Set EMAC activity LEDs to active high
arm: sun8i: orangepi-2: Enable dwmac-sun8i
arm: sun8i: orangepi-one: Enable dwmac-sun8i
arm: sun8i: orangepi-pc: Enable dwmac-sun8i
arm: sun8i: sunxi-h3-h5: add dwmac-sun8i ethernet driver
arm: sun8i: sunxi-h3-h5: Add dt node for the syscon control module
ARM: sunxi: h3-h5: Convert R_CCU raw numbers to macros
Signed-off-by: Olof Johansson <olof@lixom.net>
The dwmac-sun8i hardware is present on the Orange PI Zero.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add node for SPI NOR flash on orange-pi-zero board. Disable this node
by default and leave it to users to enable it if their board has
SPI NOR flash chip populated.
SPI NOR flash was optional in the first production batch in Dec 2016.
In later batches flash chip was pre-populated. However there should
be quite a few boards around which do not have flash chip.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
H3 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We also have some new device addition (USB, mostly) that would conflict
otherwise.
-----BEGIN PGP SIGNATURE-----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=zcf9
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-h3-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3 DT changes for 4.12
H3 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We also have some new device addition (USB, mostly) that would conflict
otherwise.
* tag 'sunxi-dt-h3-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sun8i: h2+: enable USB OTG for Orange Pi Zero board
ARM: sun8i: h3: enable USB OTG on Orange Pi One
ARM: sunxi: h3/h5: add usb_otg and OHCI/EHCI for usbc0 on H3/H5
arm: sun8i: h3: split Allwinner H3 .dtsi
arm: sun8i: h3: correct the GIC compatible in H3 to gic-400
arm: sun8i: h3: drop pinctrl-a10.h inclusion for H3 DTSI
arm: sun8i: h3: drop skeleton.dtsi inclusion in H3 DTSI
Signed-off-by: Olof Johansson <olof@lixom.net>
Orange Pi Zero board features a USB OTG port, which has a ID pin, and
can be used to power up the board. However, even if the board is powered
via +5V pin in GPIO/expansion headers, the VBUS in the OTG port cannot
be powered up, thus it's impossible to use it in host mode with simple
OTG cables.
Add support for it in peripheral mode.
If someone really want to use it in host mode, the mode of PHY can be
switch via sysfs, then use a powered USB OTG cable or powered USB HUB to
power up external USB devices.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
XR819 seems to need a delay after its reset line to be deasserted,
otherwise it may not respond MMC commands correctly, and fail to
initialize.
Add a 200ms delay in the mmc-pwrseq.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orange Pi Zero is a board that came with the new Allwinner H2+ SoC and a
SDIO Wi-Fi chip by Allwinner (XR819).
Add a device tree file for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
