Mark of the Unicorn released 896 mk3 FireWire in 2008 as part of the third
generation of its FireWire series. In 2011, 896 mk3 hybrid was released to
support USB protocol.
It supports sampling transfer frequency up to 192.0 kHz. The packet
format differs depending on both of current sampling transfer frequency
and the type of signal in optical interfaces. The model supports
transmission of PCM frames as well as MIDI messages.
The 896 mk3 FireWire consists of below ICs:
* Texas Instruments TSB41AB2
* Xilinx Spartan-3A FPGA, XC3S500E
* Texas Instruments TMS320C6722
* Microchip (Atmel) AT91SAM SAM7S256
It supports sampling transfer frequency up to 192.0 kHz. The packet
format differs depending on both of current sampling transfer frequency
and the type of signal in two pairs of optical interfaces. The model
supports transmission of PCM frames, while has no port for MIDi messages.
The model supports command mechanism to configure internal DSP. Hardware
meter information is available in the first 2 chunks of each data block
of tx packet.
This commit adds support for it. The 896 mk3 FireWire is just tested, but
the 896 mk3 Hybrid is not yet.
$ config-rom-pretty-printer < motu-896mk3fw.img
ROM header and bus information block
-----------------------------------------------------------------
1024 04100ce1 bus_info_length 4, crc_length 16, crc 3297
1028 31333934 bus_name "1394"
1032 20ff7000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 7 (256)
1036 0001f200 company_id 0001f2 |
1040 00093add device_id 0000604893 | EUI-64 0547556791237341
root directory
-----------------------------------------------------------------
1044 0004ef04 directory_length 4, crc 61188
1048 030001f2 vendor
1052 0c0083c0 node capabilities: per IEEE 1394
1056 d1000002 --> unit directory at 1064
1060 8d000005 --> eui-64 leaf at 1080
unit directory at 1064
-----------------------------------------------------------------
1064 0003998d directory_length 3, crc 39309
1068 120001f2 specifier id
1072 13000017 version
1076 17101800 model
eui-64 leaf at 1080
-----------------------------------------------------------------
1080 0002cc82 leaf_length 2, crc 52354
1084 0001f200 company_id 0001f2 |
1088 00093add device_id 0000604893 | EUI-64 0547556791237341
$ config-rom-pretty-printer < motu-896mk3hybrid.img
ROM header and bus information block
-----------------------------------------------------------------
1024 04103cbe bus_info_length 4, crc_length 16, crc 15550
1028 31333934 bus_name "1394"
1032 20ff7000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 7 (256)
1036 0001f200 company_id 0001f2 |
1040 000ae601 device_id 0000714241 | EUI-64 0547556791346689
root directory
-----------------------------------------------------------------
1044 0004ef04 directory_length 4, crc 61188
1048 030001f2 vendor
1052 0c0083c0 node capabilities: per IEEE 1394
1056 d1000002 --> unit directory at 1064
1060 8d000005 --> eui-64 leaf at 1080
unit directory at 1064
-----------------------------------------------------------------
1064 000394ac directory_length 3, crc 38060
1068 120001f2 specifier id
1072 13000037 version
1076 17102800 model
eui-64 leaf at 1080
-----------------------------------------------------------------
1080 0002cf69 leaf_length 2, crc 53097
1084 0001f200 company_id 0001f2 |
1088 000ae601 device_id 0000714241 | EUI-64 0547556791346689
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20240129022711.254383-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark of the Unicorn designed Track 16 2011 as one of models in third
generation of its FireWire series. The model is already discontinued.
It consists of below ICs:
* Texas Instruments TSB41AB1
* Microchip (SMSC) USB3300
* Xilinx Spartan-3A FPGA, XC3S700A
* Texas Instruments TMS320C6722
* Microchip (Atmel) AT91SAM SAM7S512
It supports sampling transfer frequency up to 192.0 kHz. The packet
format differs depending on both of current sampling transfer frequency
and the type of signal in optical interfaces. The model supports
transmission of PCM frames as well as MIDI messages.
The model supports command mechanism to configure internal DSP. Hardware
meter information is available in the first 2 chunks of each data block
of tx packet.
This commit adds support for it.
$ cd linux-firewire-tools/src
$ python crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04107d95 bus_info_length 4, crc_length 16, crc 32149
404 31333934 bus_name "1394"
408 20ff7000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 7 (256)
40c 0001f200 company_id 0001f2 |
410 000a83c4 device_id 00000a83c4 | EUI-64 0001f200000a83c4
root directory
-----------------------------------------------------------------
414 0004ef04 directory_length 4, crc 61188
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 d1000002 --> unit directory at 428
424 8d000005 --> eui-64 leaf at 438
unit directory at 428
-----------------------------------------------------------------
428 00035b04 directory_length 3, crc 23300
42c 120001f2 specifier id
430 13000039 version
434 17102800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 0002b25f leaf_length 2, crc 45663
43c 0001f200 company_id 0001f2 |
440 000a83c4 device_id 00000a83c4 | EUI-64 0001f200000a83c4
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20211107110644.23511-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A user of FFADO project reported the issue of ToneWeal FW66. As a result,
the device is identified as one of applications of BeBoB solution.
I note that in the report the device returns contradictory result in plug
discovery process for audio subunit. Fortunately ALSA BeBoB driver doesn't
perform it thus it's likely to handle the device without issues.
I receive no reaction to test request for this patch yet, however it would
be worth to add support for it.
daniel@gibbonmoon:/sys/bus/firewire/devices/fw1$ grep -r . *
Binary file config_rom matches
dev:244:1
guid:0x0023270002000000
hardware_version:0x000002
is_local:0
model:0x020002
model_name:FW66
power/runtime_active_time:0
power/runtime_active_kids:0
power/runtime_usage:0
power/runtime_status:unsupported
power/async:disabled
power/runtime_suspended_time:0
power/runtime_enabled:disabled
power/control:auto
subsystem/drivers_autoprobe:1
uevent:MAJOR=244
uevent:MINOR=1
uevent:DEVNAME=fw1
units:0x00a02d:0x010001
vendor:0x002327
vendor_name:ToneWeal
fw1.0/uevent:MODALIAS=ieee1394:ven00002327mo00020002sp0000A02Dver00010001
fw1.0/power/runtime_active_time:0
fw1.0/power/runtime_active_kids:0
fw1.0/power/runtime_usage:0
fw1.0/power/runtime_status:unsupported
fw1.0/power/async:disabled
fw1.0/power/runtime_suspended_time:0
fw1.0/power/runtime_enabled:disabled
fw1.0/power/control:auto
fw1.0/model:0x020002
fw1.0/rom_index:15
fw1.0/specifier_id:0x00a02d
fw1.0/model_name:FW66
fw1.0/version:0x010001
fw1.0/modalias:ieee1394:ven00002327mo00020002sp0000A02Dver00010001
Cc: Daniel Jozsef <daniel.jozsef@gmail.com>
Reference: https://lore.kernel.org/alsa-devel/20200119164335.GA11974@workstation/
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210619083922.16060-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU 896 is a second model in MOTU FireWire series, produced in 2001. This
model consists of three chips:
* Texas Instruments TSB41AB2 (Physical layer for IEEE 1394 bus)
* Philips Semiconductors PDI 1394L21BE (Link layer for IEEE 1394 bus and
packet processing layer)
* QuickLogic QuickRAM QL4016 (Data block processing layer and digital
signal processing)
This commit adds a support for the model, with its unique protocol as
version 1. The features of this protocol are:
* no MIDI support.
* Rx packets have no data chunks for control and status messages.
* Tx packets have 2 bytes for control and status messages in the end of
each data block.
* The most of settings are represented in bit flag in one quadlet address
(0x'ffff'f000'0b14).
* It's selectable to use signal on optical interface, however the device
has no register specific to it. The state has effect just to whether
to exclude differed data chunks.
* The internal multiplexer is not configured by software.
Just after powering on, the device has a quirk to fail handling
transaction. I recommend users to connect the device enough after powering
on.
$ python3 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04102814 bus_info_length 4, crc_length 16, crc 10260
404 31333934 bus_name "1394"
408 20001000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 1 (4)
40c 0001f200 company_id 0001f2 |
410 0000d645 device_id 000000d645 | EUI-64 0001f2000000d645
root directory
-----------------------------------------------------------------
414 0004c65c directory_length 4, crc 50780
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 0003ab34 directory_length 3, crc 43828
42c 120001f2 specifier id
430 13000002 version
434 17102801 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 0002057d leaf_length 2, crc 1405
43c 0001f200 company_id 0001f2 |
440 0000d645 device_id 000000d645 | EUI-64 0001f2000000d645
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210616082847.124688-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU 828 is a first model in MOTU FireWire series, produced in 2001. This
model consists of three chips:
* Texas Instruments TSB41AB1 (Physical layer for IEEE 1394 bus)
* Philips Semiconductors 1394L21BE (Link layer for IEEE 1394 bus and
packet processing layer)
* QuickLogic QuickRAM QL4016 (Data block processing layer and digital
signal processing)
This commit adds a support for this model, with its unique protocol as
version 1. The features of this protocol are:
* no MIDI support.
* Rx packets have no data chunks for control and status messages.
* Tx packets have 2 data chunks for control and status messages in the
end of each data block. The chunks consist of data block counter
(4 byte) and message (2 byte).
* All of settings are represented in bit flag in one quadlet address
(0x'ffff'f000'0b00).
* When optical interface is configured as S/PDIF, signals of the interface
is multiplexed for packets, instead of signals of coaxial interface.
* The internal multiplexer is not configured by software.
I note that the device has a quirk to mute output voluntarily during
receiving batch of packets in the beginning of packet streaming. The
operation to unmute should be done by software enough after the device
shifts the state, however it's not deterministic. Furthermore, just
after switching rate of sampling clock, the device keeps the state longer.
This patch manages to sleep 100 msec before unmute operation, but it may
fail to release the mute in the case that the rate is changed. As a
workaround, users can restart packet streaming at the same rate, or write
to specific register from userspace.
$ python3 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04105c54 bus_info_length 4, crc_length 16, crc 23636
404 31333934 bus_name "1394"
408 20001000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 1 (4)
40c 0001f200 company_id 0001f2 |
410 00005015 device_id 0000005015 | EUI-64 0001f20000005015
root directory
-----------------------------------------------------------------
414 0004c65c directory_length 4, crc 50780
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 00035052 directory_length 3, crc 20562
42c 120001f2 specifier id
430 13000001 version
434 17101800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 0002eeb6 leaf_length 2, crc 61110
43c 0001f200 company_id 0001f2 |
440 00005015 device_id 0000005015 | EUI-64 0001f20000005015
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210616082847.124688-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nowadays a lot of devices are supported by ALSA dice driver. This commit
fills Kconfig with entries for them.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210613082621.10900-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds support for the hybrid model of MOTU Ultralite mk3 with
alpha connector, which is already discontinued. The hardware specification
of the model is the same as the one of FireWire-only model.
$ cd linux-firewire-utils
$ python3 src/crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04101573 bus_info_length 4, crc_length 16, crc 5491
404 31333934 bus_name "1394"
408 20ff7000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 7 (256)
40c 0001f200 company_id 0001f2 |
410 000a059c device_id 00000a059c | EUI-64 0001f200000a059c
root directory
-----------------------------------------------------------------
414 0004ef04 directory_length 4, crc 61188
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 d1000002 --> unit directory at 428
424 8d000005 --> eui-64 leaf at 438
unit directory at 428
-----------------------------------------------------------------
428 0003f00b directory_length 3, crc 61451
42c 120001f2 specifier id
430 13000030 version
434 17103800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 0002d89c leaf_length 2, crc 55452
43c 0001f200 company_id 0001f2 |
440 000a059c device_id 00000a059c | EUI-64 0001f200000a059c
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210606043409.40019-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 0edabdfe89.
I've explained that optional FireWire card for d.2 is also built-in to
d.2 Pro, however it's wrong. The optional card uses DM1000 ASIC and has
'Mackie DJ Mixer' in its model name of configuration ROM. On the other
hand, built-in FireWire card for d.2 Pro and d.4 Pro uses OXFW971 ASIC
and has 'd.Pro' in its model name according to manuals and user
experiences. The former card is not the card for d.2 Pro. They are similar
in appearance but different internally.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210518084557.102681-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mackie d.2 has an extension card for IEEE 1394 communication, which uses
BridgeCo DM1000 ASIC. On the other hand, Mackie d.4 Pro has built-in
function for IEEE 1394 communication by Oxford Semiconductor OXFW971,
according to schematic diagram available in Mackie website. Although I
misunderstood that Mackie d.2 Pro would be also a model with OXFW971,
it's wrong. Mackie d.2 Pro is a model which includes the extension card
as factory settings.
This commit fixes entries in Kconfig and comment in ALSA OXFW driver.
Cc: <stable@vger.kernel.org>
Fixes: fd6f4b0dc1 ("ALSA: bebob: Add skelton for BeBoB based devices")
Fixes: ec4dba5053 ("ALSA: oxfw: Add support for Behringer/Mackie devices")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210513125652.110249-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is trivial commit but fulfill missing entries in Kconfig for devices
supported by ALSA firewire-motu driver.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200511022540.161363-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface UFX was shipped by RME GmbH in 2010, and now discontinued.
Although this model has some enhanced feature which Fireface 802
doesn't have (e.g. on-board USB mass storage device class, configuration
interface with color display), the functionality relevant to
packet communication on IEEE 1394 bus seems to be the same as
Fireface 802 (e.g. available number of channels for PCM frame in
each sampling transfer frequency).
With the assumption, this commit adds support for Fireface UFX. In ALSA
fireface driver, these two models are handled as the same one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200510074301.116224-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface 802 was shipped by RME GmbH in 2014. This model supports later
protocol for management of isochronous communication and synchronization
of sampling transmission frequency.
This model consists of below ICs:
* TI TSB41AB2
* Xilinx Spartan-6 FPGA XC6SLX16
* TI TMS320 C6747
* SMSC USB3250
Especially, this model just supports IEEE 1394a, against its name which
evokes Fireface 800.
This commit adds support for Fireface 802 (tested). Userspace applications
can transfer PCM frames and MIDI messages via ALSA PCM/Rawmidi interface.
I note that 4 channels for ADAt1 and ADAT2 are disabled at higher sampling
transfer frequency since isochronous resources reservation fails due to
bandwidth limitation of IEEE 1394a.
The value read from LATTER_SYNC_STATUS register is slightly different
from the one of Fireface UCX. The higher 4 bits and lower 4 bits are
swapped within the same byte.
Without any assist of userspace application, transmitted MIDI messages
from the device are not going to be processed. For detail, please refer
to my comment in code of latter protocol.
$ python crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 0404ffff bus_info_length 4, crc_length 4, crc 65535 (should be 26805)
404 31333934 bus_name "1394"
408 20008000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 8 (512)
40c 000a3504 company_id 000a35 |
410 38077423 device_id 0438077423 | EUI-64 000a350438077423
root directory
-----------------------------------------------------------------
414 0005ffff directory_length 5, crc 65535 (should be 9514)
418 0c0083c0 node capabilities per IEEE 1394
41c 03000a35 vendor
420 8100000b --> descriptor leaf at 44c
424 8d000007 --> eui-64 leaf at 440
428 d1000001 --> unit directory at 42c
unit directory at 42c
-----------------------------------------------------------------
42c 0004ffff directory_length 4, crc 65535 (should be 45134)
430 12000a35 specifier id
434 13000005 version
438 17101800 model
43c 81000008 --> descriptor leaf at 45c
eui-64 leaf at 440
-----------------------------------------------------------------
440 0002ffff leaf_length 2, crc 65535 (should be 60131)
444 000a3504 company_id 000a35 |
448 38077423 device_id 0438077423 | EUI-64 000a350438077423
descriptor leaf at 44c
-----------------------------------------------------------------
44c 0003ffff leaf_length 3, crc 65535 (should be 469)
450 00000000 textual descriptor
454 00000000 minimal ASCII
458 524d4521 "RME!"
descriptor leaf at 45c
-----------------------------------------------------------------
45c 0005ffff leaf_length 5, crc 65535 (should be 10561)
460 00000000 textual descriptor
464 00000000 minimal ASCII
468 46697265 "Fire"
46c 66616365 "face"
470 20383032 " 802"
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200510074301.116224-6-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20191004144931.3851-1-krzk@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fireface UFX was shipped by RME GmbH in 2012. This model supports later
protocol for management of isochronous communication and synchronization
of sampling transmission frequency.
This commit adds support for the model. At present, it's not clear how
to encode MIDI messages and decide destination address for asynchronous
transaction, thus this commit adds support for isochronous communication
for PCM frames only.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface 800 is a flagship model of RME GmbH for audio and music units
on IEEE 1394 bus, shipped 2004. This model consists of four chips:
- TI TSB81BA3D for physical layer on cable environment of EEE 1394 bus
- TI TSB82AA2 for link layer for 1394 OHCI bus bridge to PCI bus
- Xilinx Spartan-3 FPGA XC3S400
- Xilinx High-Performance CPLD XC9572XL
This commit adds support Fireface 800. In this time, the support is
restricted to its MIDI functionality, thus this commit adds some
condition statements to avoid touching streaming functionality.
Unlike Fireface 400, Fireface 800 has no functionality to suppress
asynchronous transactions for MIDI messages except for unregister of
listen address in controller side, thus the feature is available as is.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface 400 is a second model of RME Fireface series, released in 2006.
This commit adds support for this model.
This model supports 8 analog channels, 2 S/PDIF channels and 8 ADAT
channels in both of tx/rx packet. The number of ADAT channels differs
depending on each mode of sampling transmission frequency.
$ python2 linux-firewire-utils/src/crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04107768 bus_info_length 4, crc_length 16, crc 30568 (should be 61311)
404 31333934 bus_name "1394"
408 20009002 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 9 (1024)
40c 000a3501 company_id 000a35 |
410 1bd0862a device_id 011bd0862a | EUI-64 000a35011bd0862a
root directory
-----------------------------------------------------------------
414 000485ec directory_length 4, crc 34284
418 03000a35 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 000314c4 directory_length 3, crc 5316
42c 12000a35 specifier id
430 13000002 version
434 17101800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 000261a8 leaf_length 2, crc 25000
43c 000a3501 company_id 000a35 |
440 1bd0862a device_id 011bd0862a | EUI-64 000a35011bd0862a
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other drivers for audio and
music units on IEEE 1394 have.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for RME Fireface series. This commit just
creates/removes card instance according to IEEE 1394 bus event. More
functions will be added in following commits.
Three types of firmware have released by RME GmbH; for Fireface 400, for
Fireface 800 and for UCX/802/UFX. It's reasonable that these models use
different protocol for communication. Currently, I've investigated
Fireface 400 and nothing others.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU 828mk3 (FireWire/Hybrid) is one of third generation in MOTU FireWire
series, produced in 2008/2014. This model consists of three chips for
functionality on IEEE 1394 bus:
* TI TSB41AB2 (Physical layer for IEEE 1394 bus)
* Xilinx Spartan-3E FPGA Family (Link layer for IEEE 1394 bus, packet
processing and data block processing layer)
* TI TMS320C6722 (Digital signal processing)
This commit adds a support for this model, with its unique protocol as
version 3. This protocol has some additional features to protocol
version 2.
* Support several optical interfaces.
* Support a data chunk for return of reverb effect.
* Have a quirk of tx packets.
* Support heartbeat asynchronous transaction.
In this protocol, series of transferred packets has some quirks. Below
fields in CIP headers of the packets are out of IEC 61883-1:
- SID (source node id): always 0x0d
- DBS (data block size): always 0x04
- DBC (data block counter): always 0x00
- EOH (End of header): always 0x00
Below is an actual sample of transferred packets.
quads CIP1 CIP2
520 0x0D040400 0x22FFFFFF
8 0x0D040400 0x22FFFFFF
520 0x0D040400 0x22FFFFFF
520 0x0D040400 0x22FFFFFF
8 0x0D040400 0x22FFFFFF
Status of clock is configured by write transactions to 0x'ffff'f000'0b14,
as well as version 2, while meanings of fields are different from the
former protocols. Modes of optical interfaces are configured by write
transactions to 0x'ffff'f000'0c94.
Drivers can register its address to receive heatbeat transactions from the
unit. 0x'ffff'f000'0b0c is for the higher part and 0x'ffff'f000'0b10 is
for the lower part. Nevertheless, this feature is not useless for this
driver and this commit omits it.
Each data block consists of two parts in a point of the number of included
data chunks. In both of 'fixed' and 'differed' parts, the number of
included data blocks are a multiple of 4, thus depending on models there's
some empty data chunks. For example, 828mk3 includes one pair of empty
data chunks in its fixed part. When optical interface is configured to
S/PDIF, 828mk3 includes one pair of empty data chunks in its differed part.
To reduce consumption of CPU cycles with additional conditions/loops, this
commit just exposes these empty chunks to user space as PCM channels.
Additionally, 828mk3 has a non-negligible overhead to change its sampling
transfer frequency. When softwares send asynchronous transaction to
perform it, LED on the unit starts to blink. In a worst case, it continues
blink during several seconds; e.g. 10 seconds. When stopping blinking,
the unit seems to be prepared for the requested sampling transfer
frequency. To wait for the preparation, this commit forces the driver
to call task scheduler and applications sleeps for 4 seconds.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU 828mk2 is one of second generation in MOTU FireWire series, produced in
2003. This model consists of four chips:
* TI TSB41AB2 (Physical layer for IEEE 1394 bus)
* PDI 1394L40BE (Link layer for IEEE 1394 bus and packet processing layer)
* ALTERA ACEX 1K EP1K30 Series FPGA (Data block processing layer)
* TI TMS320VC5402 (Digital signal processing)
This commit adds a support for this model, with its unique protocol as
version 2. The features of this protocol are:
* Support data chunks for status and control messages for both
directions.
* Support a pair of MIDI input/output.
* Support a data chunk for mic/instrument independent of analog line in.
* Support a data chunk for playback return.
* Support independent data chunks for S/PDIF of both optical/coaxial
interfaces.
* Support independent data chunks for each of main out and phone out.
Status of clock is configured by write transactions to 0x'ffff'f000'0b14.
Modes of optical interfaces are configured by write transactions to
0x'ffff'f000'0c04.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds an new driver for MOTU FireWire series. In this commit,
this driver just creates/removes card instance according to bus event.
More functionalities will be added in following commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I forgot it.
Fixes: 3e78e1518e12('ALSA: firewire-tascam: add support for FW-1804')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now ALSA oxfw driver gains functionalities which scs1x module has.
This commit obsoletes the scs1x module, and adds a line of MODULE_ALIAS
to load oxfw module instead of scs1x module.
In scs1x module, the name of 'shortname' field is fixed as 'SCS1x'. This
field is used to name MIDI ports for both of SCS.1m and SCS.1d. This is
not good because typically some SCS.1m and SCS.1d are used in the same
system. It's better to distinguish them according to name of the ports.
This commit applies model name in config ROM to the 'shortname'.
For the name of 'driver' and 'longname', this commit uses the same way
applied to the other models. This change may not bring disadvantages to
users because userspace applications use ALSA rawmidi or seq interface
and these interfaces are not influenced by them directly.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A commit to add support for this model should have added a comment
about this model to Kconfig.
Fixes: 759a2f40c9fa('ALSA: oxfw: add an entry for TASCAM FireOne')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other IEEE 1394 sound devices
has.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for TASCAM FireWire series. In this commit,
this driver just creates/removes card instance according to bus event.
More functionalities will be added in following commits.
TASCAM FireWire series consists of:
* PDI 1394P23 for IEEE 1394 PHY layer
* PDI 1394L40 for IEEE 1394 LINK layer and IEC 61883 interface
* XILINX XC9536XL
* XILINX Spartan-II XC2S100
* ATMEL AT91M42800A
Ilya Zimnovich had investigated TASCAM FireWire series in 2011, and
discover some features of his FW-1804. You can see a part of his research
in FFADO project.
http://subversion.ffado.org/wiki/Tascam
A part of my work are based on Ilya's investigation, while this series
doesn't support the FW-1804, because of a lack of config ROM
information and its protocol detail, especially for PCM channels.
I observed that FW-1884 and FW-1082 don't work properly with 1394 OHCI
controller based on VT6315. The controller can actually communicate packets
to these models, while these models generate no sounds. It may be due to
the PHY/LINK layer issues. Using 1394 OHCI controller produced by the other
vendors such as Texas Instruments may work. Or adding another node on the
bus.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other sound drivers for units
on IEEE 1394 bus have.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for Digidesign 002/003 family. This commit
just creates/removes card instance according to bus event. More functions
will be added in following commits.
Digidesign 002/003 family consists of:
* Agere FW802B for IEEE 1394 PHY layer
* PDI 1394L40 for IEEE 1394 LINK layer and IEC 61883 interface
* ALTERA ACEX EP1K50 for IEC 61883 layer and DSP controller
* ADSP-21065L for signal processing
[minor cleanup using skip_spaces() by tiwai]
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This device is based on DM1000E, and BeBoB version 1 firmware is
installed.
$ cat /proc/asound/cards
0 [Pro ]: BeBoB - Mbox 2 Pro
DIGIDESIGN Mbox 2 Pro (id:1, rev:1),
GUID 00a07e0100a90000 at fw1.0, S400
$ cat /proc/asound/Pro/firewire/firmware
Manufacturer: bridgeCo
Protocol Ver: 1
Build Ver: 0
GUID: 0x00A07E0100A90000
Model ID: 0x01
Model Rev: 1
Firmware Date: 20071031
Firmware Time: 034402
Firmware ID: 0xA9
Firmware Ver: 16777215
Base Addr: 0x20080000
Max Size: 1572864
Loader Date: 20051207
Loader Time: 205554
With this patch, ALSA BeBoB driver can start packet streaming to/from
this model, while as a default, internal multiplexer of this model is
not initialized and generates no sound even if the driver transfers
any packets with PCM samples. To hear any sounds from this model,
userspace applications should be developed to set parameters to the
internal multiplexer. You can see raw information in FFADO website:
http://subversion.ffado.org/wiki/AvcModels/DigiDesignMboxPro2
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This interface is designed for mixer/control application. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some devices produced by Behringer/Mackie are based on OXFW970/971. This
commit adds support for them. Additionally, this commit changes the way to
name card with some information in config rom.
Ids of some Mackie(Loud) models are not identified, therefore this commit
applies name detection for these models.
The devices support capture/playback of PCM-samples and some of them
supports capture/playback of MIDI messages. These functionalities are
implemented by followed commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a support for capturing PCM samples.
When opposite PCM substream is already running, available sampling rate is
limited at current one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit renames 'firewire-speakers' to 'oxfw' to enhance support for
devices which based on OXFW970/971. A line for MODULE_ALIAS is added.
Additionally, to help for works in followed paches, some members
in private structure are renamed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some developers test this driver, thus it's better to remove its
experimental state.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now snd-firewire-lib supports rawmidi in addition to PCM, thus we need
to give a proper dependency. For fixing and simplification, move the
selections of SND_PCM and SND_RAWMIDI into SND_FIREWIRE_LIB section.
Then each driver doesn't have to select them but only
SND_FIREWIRE_LIB.
Reported-by: Jim Davis <jim.epost@gmail.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to support some models which M-Audio produces
with DM1000 but its firmware is special. They are:
- Firewire 1814
- ProjectMix I/O
They have heavily customized firmware. The usual operations can't be applied to
them. For this reason, this commit adds a model specific member to 'struct
snd_bebob' and some model specific functions. Some parameters are write-only so
this commit also adds control interface for applications to set them.
M-Audio special firmware quirks:
- Just after powering on, they wait to download firmware. This state is
changed when receiving cue. Then bus reset is generated and the device is
recognized as a different model with the uploaded firmware.
- They don't respond against BridgeCo AV/C extension commands. So drivers
can't get their stream formations and so on.
- They do not start to transmit packets only by establishing connection but
also by receiving SIGNAL FORMAT command.
- After booting up, they often fail to send response against driver's request
due to mismatch of gap_count.
This module don't support to upload firmware.
Tested-by: Darren Anderson <darrena092@gmail.com> (ProjectMix I/O)
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to support some models which M-Audio produces
with DM1000/DM1000E with usual firmware. They are:
- Firewire 410
- Firewire AudioPhile
- Firewire Solo
- Ozonic
- NRV10
- FirewireLightBridge
According to a person who worked in BridgeCo, some models are produced with
'Pre-BeBoB'. This means that these products were released before BeBoB was
officially produced, and later BeBoB specification was formed. So these models
have some quirks.
M-Audio usual firmware quirks:
- Just after powering on, 'Firewire 410' waits to download firmware. This
state is changed when receiving cue. Then bus reset is generated and the
device is recognized as a different model with the uploaded firmware.
- 'Firewire Audiophile' also waits to download firmware but its
vendor id/model id is the same as the one after loading firmware.
- The information of channel mapping for MIDI conformant data channel is
invalid against BridgeCo specification.
This commit adds some codes for these quirks but don't support to upload
firmware.
This commit also adds specific operations to get metering information. The
metering information also includes status of clock synchronization if the model
supports to switch source of clock.
The specification of FirewireLightBridge is unknown. So in this time, normal
operations are applied for this model.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to support all of models which Focusrite
produces with DM1000/BeBoB. They are:
- Saffire
- Saffire LE
- SaffirePro 10 I/O
- SaffirePro 26 I/O
This commit adds Focusrite specific operations:
1. Get source of clock
2. Get/Set sampling frequency
3. Get metering information
The driver uses these functionalities to read/write specific address by async
transaction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to support all of models which Yamaha produced
with DM1000/BeBoB. They are:
- GO44
- GO46
This commit adds Yamaha specific operations. To get source of clock, AV/C Audio
Subunit command is used.
I note that their appearances are similar to some models of TerraTec; 'Go44' is
similar to 'PHASE 24 FW' and 'GO46' is similar to 'PHASE X24 FW'. But their
combination of Audio/Music subunits is a bit different.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to support all of models which Terratec produced
with DM1000/BeBoB. They are:
- PHASE 24 FW
- PHASE X24 FW
- PHASE 88 Rack FW
- EWS MIC2
- EWS MIC4
- Aureon 7.1 Firewire
For Phase series, this commit adds a Terratec specific operation. To get source
of clock. AV/C Audio Subunit command is used.
For EWS series and Aureon, this module uses normal operations.
Tested-by: Maximilian Engelhardt <maxi@daemonizer.de> (PHASE 24 FW)
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This interface is designed for mixer/control application. By using hwdep
interface, the application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to capture/playback PCM samples.
When AMDTP stream is already running for PCM or the source of clock is not
internal, available sampling rate is limited at current one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to capture/playback MIDI messages.
When no AMDTP streams are running, this module starts AMDTP stream at current
sampling rate for MIDI substream.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
