Add a SSYNC() into bfin_serial_dma_tx_chars() to ensure DMA registers are
written with new data otherwise we might miss a byte or two when the
system is under load. PIO mode is OK though.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we already setup the early console UART in
arch/blackfin/kernel/early_printk.c, and common functions which are
enabled from the .setup will override the proper settings later, don't
fill in these structures. Otherwise we get mangled baudrate settings when
using early_printk.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ignore receiving data if new position is in the same line of current
buffer tail and is small. This should decrease overruns.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hopefuly the new version is easier to read, but in the process it declares
proper clobber lists and better constraints so that GCC can do a better
job at allocating free registers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPORT transmit frame sync (TFS) isn't used as an electrical signal during
normal SPORT UART emulation. However, it is useful in EIA RS-485
emulation as RS-485 Transceiver Driver Enable DE strobe.
This patch configures:
TFS to be active high in order to drive an DE strobe of
an eventually connected RS-485 Transceiver.
Late frame sync mode (LATFS) gating the entire TX shift cycle.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the TI AR7 internal UART.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As it is, defining ICOM_TRACE produces some compile errors, as
"parameter name omitted" and "redefinition of ‘trace’"
This patch removes the wrong trace definition.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
And tidy up a few bits coding style detectors missed
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael's patch fixed some of the coding style so the style is now
inconsistent. Sort the rest out
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes array subscription bugs in the parport_pc driver.
drivers/parport/parport_pc.c: In function ‘parport_irq_probe’:
drivers/parport/parport_pc.c:1589: warning: array subscript is above array bounds
drivers/parport/parport_pc.c: In function ‘parport_pc_probe_port’:
drivers/parport/parport_pc.c:1579: warning: array subscript is above array bounds
The patch also fixes a few other array bugs, which the compiler was
unable to find. Coding style violations are also fixed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Having cleaned up the allocators we might as well remove the inline helpers
for some of it
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Long long ago a 4K kmalloc allocated two pages so the tty layer used the
page allocator, except on some machines where the page size was huge. This was
removed from the core tty layer with the tty buffer re-implementation but not
from tty_audit or the n_tty ldisc.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
adapter->version can only be ADAPTER_V2 or ADAPTER_V1. So,
that OR operand in the "if" clause is non-sense and can be removed.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If there are more then one 4/8-port board jsm_uart_port_init
allocate a line numbers of the second and further boards
from range of previous one.
This patch fixed the problem.
Signed-off-by: Alexander Y. Fomichev <git.user@gmail.com>
[printks fixed to add jsm: ]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
set_termios can now be used for setting the parity and the stopbits. This is
needed to use with cards which use a different parity then the parity used at
start (even).
If the iuu_uart_baud function return an error, we will return the old_termios
instead of the new one.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
This was then revamped to use the various helpers, not copy non-hardware
bits any to add mark/space parity and csize reporting
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring in the relevant bits of the 0.9 vendor driver.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have a tty_ldisc file now so put tty_ldisc_flush in the right place
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are several pretty much unfixable races in the old ldisc code, especially
with respect to pty behaviour and also to hangup. It's easier to rewrite the
code than simply try and patch it up.
This patch
- splits the ldisc from the tty (so we will be able to refcount it more cleanly
later)
- introduces a mutex lock for ldisc changing on an active device
- fixes the complete mess that hangup caused
- implements hopefully correct setldisc/close/hangup locking
There are still some problems around pty pairs that have always been there but
at least it is now possible to understand the code and fix further problems.
This fixes the following known bugs
- hang up can leak ldisc references
- hang up may not call open/close on ldisc in a matched way
- pty/tty pairs can deadlock during an ldisc change
- reading the ldisc proc files can cause every ldisc to be loaded
and probably a few other of the mysterious ldisc race reports.
I'm sure it also adds the odd new one.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before trying to tackle the ldisc bugs the code needs to be a good deal
more readable, so do the simple extractions of routines first.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Costantino Leandro found a bug in tty_find_polling_driver and provided a
patch that fixed the crash but not the underlying bug. This fixes the
underlying bug where the list walk corrupts the values it is using on a
match but then reuses them if the open fails.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We fixed the globals, so now fix the comment
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty throttling code can race due to the lock drops. It takes very high
loads but this has been observed and verified by Rob Duncan.
The basic problem is that on an SMP box we can go
CPU #1 CPU #2
need to throttle ?
suppose we should buffer space cleared
are we throttled
yes ? - unthrottle
call throttle method
This changeet take the termios lock to protect against this. The termios
lock isn't the initial obvious candidate but many implementations of throttle
methods already need to poke around their own termios structures (and nobody
really locks them against a racing change of flow control).
This does mean that anyone who is setting tty->low_latency = 1 and then
calling tty_flip_buffer_push from their unthrottle method is going to end up
collapsing in a pile of locks. However we've removed all the known bogus
users of low_latency = 1 and such use isn't safe anyway for other reasons so
catching it would be an improvement.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for the following serial controller chip:
Oxford Semiconductor OXCB950 for PCI Cardbus interface
http://www.transdimension.com/products/serial/OXCB950.html
on this card:
ExSys EX-1370 1 port high-speed serial card for ExpressCard/34 slot
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch from ASYNC_* to ASYNCB_*, because test_bit expects
bit number, not mask.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch from ASYNC_* to ASYNCB_*, because {test,set}_bit expect
bit number, not mask.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Or at least most of it. There are further clean ups possible and there are
are also thing checkpatch moans about that would be silly to "fix".
Also note some FIXME points found as the cleanup was done.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now we have a port structure begin using the fields and kref counts
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set up ports right after FW load so that we won't allocate maximal
(64) ports when we use few.
Also remove reading of nports in irq context, since we know it from
initialisation now.
This also fixes a tty ports unregistration on some fail paths and for
Ze which registered 64 and unregistered real port count.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove ugly macros and add inlines instead of them. This improves
readability and type checking a much.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Store HW version locally to not read it all the time in interrupts
and alike.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove ugly all-over-the-code casts of ctl_addr to 9060 space.
Add an union to the cyclades_card structure, which contains
a pointer to both 9050 and 9060 spaces.
The 9050 space layout is unknown, so let it still as a void
__iomem pointer.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add receive programmed IO mode to reduce receive latency
when using low data rates. The receive FIFO trigger
level of 128 bytes used in DMA mode creates excessive latency
when operating at low data rates. PIO mode is selected when user
application requests data in blocks of less than 128 bytes.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CDC ACM driver uses the tty layer correctly so needs conversion. Start by
adding and initializing the port structures.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to clean stuff up, but is probably also going to cause
some app breakage with buggy apps as we now implement proper POSIX behaviour
for USB ports matching all the other ports. This does also mean other apps
that break on USB will now work properly.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need this for devices that cannot flush and wait, but which do not order
data and modem events. Without it we will hang up before all the data
clears the hardware. Needed for the USB changes.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers implement this internally, others miss it out. Push the
behaviour into the core code as that way everyone will do it consistently.
Update the dtr rts method to raise or lower depending upon flags. Having a
single method in this style fits most of the implementations more cleanly than
two funtions.
We need this in place before we tackle the USB side
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No need to check if dev_id is NULL, it never is.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't reset the PLX chip after FW load, which effectively kills
the FW, so that user had to boot manually.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ze needs firmware to be loaded as well as Zo. Move cyz_load_fw one
level upper to achieve that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's a bug in the mxser kernel module that still appears in the
2.6.29.4 kernel.
mxser_get_ISA_conf takes a ioaddress as its first argument, by passing the
not of the ioaddr, you're effectively passing 0 which means it won't be
able to talk to an ISA card. I have tested this, and removing the !
fixes the problem.
Cc: "Peter Botha" <peterb@goldcircle.co.za>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
cls_cgroup: Fix oops when user send improperly 'tc filter add' request
r8169: fix crash when large packets are received
* 'for-linus' of git://neil.brown.name/md:
md/raid5: fix bug in reshape code when chunk_size decreases.
md/raid5 - avoid deadlocks in get_active_stripe during reshape
md/raid5: use conf->raid_disks in preference to mddev->raid_disk
These are defined as static cpumask_var_t so if MAXSMP is not used,
they are cleared already. Avoid surprises when MAXSMP is enabled.
Signed-off-by: Yinghai Lu <yinghai.lu@kernel.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Michael Tokarev reported receiving a large packet could crash
a machine with RTL8169 NIC.
( original thread at http://lkml.org/lkml/2009/6/8/192 )
Problem is this driver tells that NIC frames up to 16383 bytes
can be received but provides skb to rx ring allocated with
smaller sizes (1536 bytes in case standard 1500 bytes MTU is used)
When a frame larger than what was allocated by driver is received,
dma transfert can occurs past the end of buffer and corrupt
kernel memory.
Fix is to tell to NIC what is the maximum size a frame can be.
This bug is very old, (before git introduction, linux-2.6.10), and
should be backported to stable versions.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
