Limit the acceptance of component name passed to cmd_flash_update() to
match one of the versions returned by info_get(), marked by version type.
This makes things clearer and enforces 1:1 mapping between exposed
version and accepted flash component.
Check VERSION_TYPE_COMPONENT version type during cmd_flash_update()
execution by calling info_get() with different "req" context.
That causes info_get() to lookup the component name instead of
filling-up the netlink message.
Remove "UPDATE_COMPONENT" flag which becomes used.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the only component user which is netdevsim. It uses component named
"fw.mgmt" in selftests. So add this version to info_get() output with
version type component.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever the driver is called by his info_get() op, it may put multiple
version names and values to the netlink message. Extend by additional
helper devlink_info_version_running/stored_put_ext() that allows to
specify a version type that indicates when particular version name
represents a flash component.
This is going to be used in follow-up patch calling info_get() during
flash update command checking if version with this the version type
exists.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
qdisc_reset() is clearing qdisc->q.qlen and qdisc->qstats.backlog
_after_ calling qdisc->ops->reset. There is no need to clear them
again in the specific reset function.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20220824005231.345727-1-shaozhengchao@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
is_post_ct_flow() function will process only ct_state ESTABLISHED,
then offload_pre_check() function will check FLOW_DISSECTOR_KEY_CT flag.
When config tc filter match ct_state(0/0x3f), dissector->used_keys
with FLOW_DISSECTOR_KEY_CT bit, function offload_pre_check() will
return false, so not offload. This is a special case that can be handled
safely.
Therefore, modify to let initial packet which won't go through conntrack
can be offloaded, as long as the cared ct fields are all zero.
Signed-off-by: Wenjuan Geng <wenjuan.geng@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220823090122.403631-1-simon.horman@corigine.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce a simple helper function to replace a common pattern.
When accessing the GRO header, we fetch the pointer from frag0,
then test its validity and fetch it from the skb when necessary.
This leads to the pattern
skb_gro_header_fast -> skb_gro_header_hard -> skb_gro_header_slow
recurring many times throughout GRO code.
This patch replaces these patterns with a single inlined function
call, improving code readability.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220823071034.GA56142@debian
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As all callbacks are converted now, fix the text reflecting that change.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20220823070213.1008956-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Joanne Koong says:
====================
Add a second bind table hashed by port and address
Currently, there is one bind hashtable (bhash) that hashes by port only.
This patchset adds a second bind table (bhash2) that hashes by port and
address.
The motivation for adding bhash2 is to expedite bind requests in situations
where the port has many sockets in its bhash table entry (eg a large number
of sockets bound to different addresses on the same port), which makes checking
bind conflicts costly especially given that we acquire the table entry spinlock
while doing so, which can cause softirq cpu lockups and can prevent new tcp
connections.
We ran into this problem at Meta where the traffic team binds a large number
of IPs to port 443 and the bind() call took a significant amount of time
which led to cpu softirq lockups, which caused packet drops and other failures
on the machine.
When experimentally testing this on a local server for ~24k sockets bound to
the port, the results seen were:
ipv4:
before - 0.002317 seconds
with bhash2 - 0.000020 seconds
ipv6:
before - 0.002431 seconds
with bhash2 - 0.000021 seconds
The additions to the initial bhash2 submission [0] are:
* Updating bhash2 in the cases where a socket's rcv saddr changes after it has
* been bound
* Adding locks for bhash2 hashbuckets
[0] https://lore.kernel.org/netdev/20220520001834.2247810-1-kuba@kernel.org/
v3: https://lore.kernel.org/netdev/20220722195406.1304948-2-joannelkoong@gmail.com/
v2: https://lore.kernel.org/netdev/20220712235310.1935121-1-joannelkoong@gmail.com/
v1: https://lore.kernel.org/netdev/20220623234242.2083895-2-joannelkoong@gmail.com/
====================
Link: https://lore.kernel.org/r/20220822181023.3979645-1-joannelkoong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds 2 new tests: sk_bind_sendto_listen and
sk_connect_zero_addr.
The sk_bind_sendto_listen test exercises the path where a socket's
rcv saddr changes after it has been added to the binding tables,
and then a listen() on the socket is invoked. The listen() should
succeed.
The sk_bind_sendto_listen test is copied over from one of syzbot's
tests: https://syzkaller.appspot.com/x/repro.c?x=1673a38df00000
The sk_connect_zero_addr test exercises the path where the socket was
never previously added to the binding tables and it gets assigned a
saddr upon a connect() to address 0.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This test populates the bhash table for a given port with
MAX_THREADS * MAX_CONNECTIONS sockets, and then times how long
a bind request on the port takes.
When populating the bhash table, we create the sockets and then bind
the sockets to the same address and port (SO_REUSEADDR and SO_REUSEPORT
are set). When timing how long a bind on the port takes, we bind on a
different address without SO_REUSEPORT set. We do not set SO_REUSEPORT
because we are interested in the case where the bind request does not
go through the tb->fastreuseport path, which is fragile (eg
tb->fastreuseport path does not work if binding with a different uid).
To run the script:
Usage: ./bind_bhash.sh [-6 | -4] [-p port] [-a address]
6: use ipv6
4: use ipv4
port: Port number
address: ip address
Without any arguments, ./bind_bhash.sh defaults to ipv6 using ip address
"2001:0db8:0:f101::1" on port 443.
On my local machine, I see:
ipv4:
before - 0.002317 seconds
with bhash2 - 0.000020 seconds
ipv6:
before - 0.002431 seconds
with bhash2 - 0.000021 seconds
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current bind hashtable (bhash) is hashed by port only.
In the socket bind path, we have to check for bind conflicts by
traversing the specified port's inet_bind_bucket while holding the
hashbucket's spinlock (see inet_csk_get_port() and
inet_csk_bind_conflict()). In instances where there are tons of
sockets hashed to the same port at different addresses, the bind
conflict check is time-intensive and can cause softirq cpu lockups,
as well as stops new tcp connections since __inet_inherit_port()
also contests for the spinlock.
This patch adds a second bind table, bhash2, that hashes by
port and sk->sk_rcv_saddr (ipv4) and sk->sk_v6_rcv_saddr (ipv6).
Searching the bhash2 table leads to significantly faster conflict
resolution and less time holding the hashbucket spinlock.
Please note a few things:
* There can be the case where the a socket's address changes after it
has been bound. There are two cases where this happens:
1) The case where there is a bind() call on INADDR_ANY (ipv4) or
IPV6_ADDR_ANY (ipv6) and then a connect() call. The kernel will
assign the socket an address when it handles the connect()
2) In inet_sk_reselect_saddr(), which is called when rebuilding the
sk header and a few pre-conditions are met (eg rerouting fails).
In these two cases, we need to update the bhash2 table by removing the
entry for the old address, and add a new entry reflecting the updated
address.
* The bhash2 table must have its own lock, even though concurrent
accesses on the same port are protected by the bhash lock. Bhash2 must
have its own lock to protect against cases where sockets on different
ports hash to different bhash hashbuckets but to the same bhash2
hashbucket.
This brings up a few stipulations:
1) When acquiring both the bhash and the bhash2 lock, the bhash2 lock
will always be acquired after the bhash lock and released before the
bhash lock is released.
2) There are no nested bhash2 hashbucket locks. A bhash2 lock is always
acquired+released before another bhash2 lock is acquired+released.
* The bhash table cannot be superseded by the bhash2 table because for
bind requests on INADDR_ANY (ipv4) or IPV6_ADDR_ANY (ipv6), every socket
bound to that port must be checked for a potential conflict. The bhash
table is the only source of port->socket associations.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
davinci_mdio.c uses mdio bitbang APIs, so it should select
MDIO_BITBANG to prevent build errors.
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdio_remove':
drivers/net/ethernet/ti/davinci_mdio.c:649: undefined reference to `free_mdio_bitbang'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdio_probe':
drivers/net/ethernet/ti/davinci_mdio.c:545: undefined reference to `alloc_mdio_bitbang'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdiobb_read':
drivers/net/ethernet/ti/davinci_mdio.c:236: undefined reference to `mdiobb_read'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdiobb_write':
drivers/net/ethernet/ti/davinci_mdio.c:253: undefined reference to `mdiobb_write'
Fixes: d04807b806 ("net: ethernet: ti: davinci_mdio: Add workaround for errata i2329")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ravi Gunasekaran <r-gunasekaran@ti.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Sudip Mukherjee (Codethink) <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20220824024216.4939-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stephen Rothwell reported htmldocs warning when merging net-next tree:
Documentation/admin-guide/sysctl/net.rst:37: WARNING: Malformed table.
Text in column margin in table line 4.
========= =================== = ========== ==================
Directory Content Directory Content
========= =================== = ========== ==================
802 E802 protocol mptcp Multipath TCP
appletalk Appletalk protocol netfilter Network Filter
ax25 AX25 netrom NET/ROM
bridge Bridging rose X.25 PLP layer
core General parameter tipc TIPC
ethernet Ethernet protocol unix Unix domain sockets
ipv4 IP version 4 x25 X.25 protocol
ipv6 IP version 6
========= =================== = ========== ==================
The warning above is caused by cells in second "Content" column of
/proc/sys/net subdirectory table which are in column margin.
Align these cells against the column header to fix the warning.
Link: https://lore.kernel.org/linux-next/20220823134905.57ed08d5@canb.auug.org.au/
Fixes: 1202cdd665 ("Remove DECnet support from kernel")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://lore.kernel.org/r/20220824035804.204322-1-bagasdotme@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit says:
====================
r8169: remove support for few unused chip versions
There's a number of chip versions that apparently never made it to the
mass market. Detection of these chip versions has been disabled for
few kernel versions now and nobody complained. Therefore remove
support for these chip versions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
v3:
- rebase patch
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
v2:
- fix a typo: RTL_GIGA_MAC_VER_40 -> RTL_GIGA_MAC_VER_50
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of these chip versions has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roi Dayan Says:
===============
Add support for SF tunnel offload
Mlx5 driver only supports VF tunnel offload.
To add support for SF tunnel offload the driver needs to:
1. Add send-to-vport metadata matching rules like done for VFs.
2. Set an indirect table for SF vport, same as VF vport.
info smaller sub functions for better maintainability.
rules from esw init phase to representor load phase.
SFs could be created after esw initialized and thus the send-to-vport
meta rules would not be created for those SFs.
By moving the creation of the rules to representor load phase
we ensure creating the rules also for SFs created later.
===============
Lama Kayal Says:
================
Make flow steering API loosely coupled from mlx5e_priv, in a manner to
introduce more readable and maintainable modules.
Make TC's private, let mlx5e_flow_steering struct be dynamically allocated,
and introduce its API to maintain the code via setters and getters
instead of publicly exposing it.
Introduce flow steering debug macros to provide an elegant finish to the
decoupled flow steering API, where errors related to flow steering shall
be reported via them.
All flow steering related files will drop any coupling to mlx5e_priv,
instead they will get the relevant members as input. Among these,
fs_tt_redirect, fs_tc, and arfs.
================
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmMEaToACgkQSD+KveBX
+j7H1wf8DPInwK4MsgilUZFXNd03RJprlptami+Feev2wmuzOIOwyTxOc+VvowFM
G6r0Yuqahg0z5oE7zgxMNNdtKevjqmaNLWuDtbvv4UQKt7hwJz28Y0Ezuz3L9sQS
JVEQpII/FhUFzHoeDTbbJojKGTO7N8hS4D7ZB9wGeQc7M8PmLiUq19PURKwGDxUq
EhNwEgxOzbd6S5OMGfD0bDOOK+TpntKctkXUpYh7rr6JlLQpor03cBfYrOx9DcST
M3Yk9ianx4fmeOeyZAAZOEzUpBkwMt74SxelIcwAAei9bcNRRI3FoNLc+PcKJjz1
c567AeSzx/HYnaoydtGFOroq8lAwnw==
=pgqu
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2022-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2022-08-22
Roi Dayan Says:
===============
Add support for SF tunnel offload
Mlx5 driver only supports VF tunnel offload.
To add support for SF tunnel offload the driver needs to:
1. Add send-to-vport metadata matching rules like done for VFs.
2. Set an indirect table for SF vport, same as VF vport.
info smaller sub functions for better maintainability.
rules from esw init phase to representor load phase.
SFs could be created after esw initialized and thus the send-to-vport
meta rules would not be created for those SFs.
By moving the creation of the rules to representor load phase
we ensure creating the rules also for SFs created later.
===============
Lama Kayal Says:
================
Make flow steering API loosely coupled from mlx5e_priv, in a manner to
introduce more readable and maintainable modules.
Make TC's private, let mlx5e_flow_steering struct be dynamically allocated,
and introduce its API to maintain the code via setters and getters
instead of publicly exposing it.
Introduce flow steering debug macros to provide an elegant finish to the
decoupled flow steering API, where errors related to flow steering shall
be reported via them.
All flow steering related files will drop any coupling to mlx5e_priv,
instead they will get the relevant members as input. Among these,
fs_tt_redirect, fs_tc, and arfs.
================
Issue found during code review. This bug has no impact as long as the
ks8851_net structure is the first element of the ks8851_net_spi structure.
As long as the offset to the ks8851_net struct is zero, the container_of()
macro is subtracting 0 and therefore no damage done. But if the
ks8851_net_spi struct is ever modified such that the ks8851_net struct
within it is no longer the first element of the struct, then the bug would
manifest itself and cause problems.
struct ks8851_net is contained within ks8851_net_spi.
ks is contained within kss.
kss is the priv_data of the netdev structure.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_md5sig_pool_populated can be read while another thread
changes its value.
The race has no consequence because allocations
are protected with tcp_md5sig_mutex.
This patch adds READ_ONCE() and WRITE_ONCE() to document
the race and silence KCSAN.
Reported-by: Abhishek Shah <abhishek.shah@columbia.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both <port> br_port_locked and <lag> interfaces's flag
offloading is supported. No new ABI is being added,
rather existing (port_param_set) API call gets extended.
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
V2:
add missing receipents (linux-kernel, netdev)
Signed-off-by: David S. Miller <davem@davemloft.net>
Siddharth Vadapalli says:
====================
J7200: CPSW5G: Add support for QSGMII mode to am65-cpsw driver
Add support for QSGMII mode to am65-cpsw driver.
Change log:
v4-> v5:
1. Move ti,j7200-cpswxg-nuss compatible to the line above the
ti,j721e-cpsw-nuss compatible.
2. Add allOf and move if-then statements within it to allow future if-then
statements to be added easily.
v3 -> v4:
1. Update bindings to disallow ports based on compatible, instead of
adding a new if/then statement for the new compatible.
2. Add Else-If condition for RMII mode in the set of supported interfaces.
Support for RMII mode is already present in the driver and I had
missed out adding a condition for RMII mode in the previous patches.
v2 -> v3:
1. In ti,k3-am654-cpsw-nuss.yaml, restrict if/then statement to port
nodes.
v1 -> v2:
1. Add new compatible for CPSW5G in ti,k3-am654-cpsw-nuss.yaml and extend
properties for new compatible.
2. Add extra_modes member to struct am65_cpsw_pdata to be used for QSGMII
mode by new compatible.
3. Add check for phylink supported modes to ensure that only one phy mode
is advertised as supported.
4. Check if extra_modes supports QSGMII mode in am65_cpsw_nuss_mac_config()
for register write.
5. Add check for assigning port->sgmii_base only when extra_modes is valid.
v4: https://lore.kernel.org/r/20220816060139.111934-1-s-vadapalli@ti.com/
v3: https://lore.kernel.org/r/20220606110443.30362-1-s-vadapalli@ti.com/
v2: https://lore.kernel.org/r/20220602114558.6204-1-s-vadapalli@ti.com/
v1: https://lore.kernel.org/r/20220531113058.23708-1-s-vadapalli@ti.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In TI's J7200 SoC CPSW5G ports, each of the 4 ports can be configured
as a QSGMII main or QSGMII-SUB port. This configuration is performed
by phy-gmii-sel driver on invoking the phy_set_mode_ext() function.
It is necessary for the QSGMII main port to be configured before any of
the QSGMII-SUB interfaces are brought up. Currently, the QSGMII-SUB
interfaces come up before the QSGMII main port is configured.
Fix this by moving the call to phy_set_mode_ext() from
am65_cpsw_nuss_ndo_slave_open() to am65_cpsw_nuss_init_slave_ports(),
thereby ensuring that the QSGMII main port is configured before any of
the QSGMII-SUB ports are brought up.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW5G in J7200 supports additional modes like QSGMII and SGMII.
Add new compatible for J7200 and enable QSGMII mode in am65-cpsw driver.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bindings for TI K3 J7200 SoC which contains 5 ports (4 external
ports) CPSW5G module and add compatible for it.
Changes made:
- Add new compatible ti,j7200-cpswxg-nuss for CPSW5G.
- Extend pattern properties for new compatible.
- Change maximum number of CPSW ports to 4 for new compatible.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes, gcc will optimize the function by spliting it to two or
more functions. In this case, kfree_skb_reason() is splited to
kfree_skb_reason and kfree_skb_reason.part.0. However, the
function/tracepoint trace_kfree_skb() in it needs the return address
of kfree_skb_reason().
This split makes the call chains becomes:
kfree_skb_reason() -> kfree_skb_reason.part.0 -> trace_kfree_skb()
which makes the return address that passed to trace_kfree_skb() be
kfree_skb().
Therefore, introduce '__fix_address', which is the combination of
'__noclone' and 'noinline', and apply it to kfree_skb_reason() to
prevent to from being splited or made inline.
(Is it better to simply apply '__noclone oninline' to kfree_skb_reason?
I'm thinking maybe other functions have the same problems)
Meanwhile, wrap 'skb_unref()' with 'unlikely()', as the compiler thinks
it is likely return true and splits kfree_skb_reason().
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Fang says:
====================
add interface mode select and RMII
From: Wei Fang <wei.fang@nxp.com>
The patches add the below feature support for both TJA1100 and
TJA1101 PHYs cards:
- Add MII and RMII mode support.
- Add REF_CLK input/output support for RMII mode.
====================
Link: https://lore.kernel.org/r/20220822015949.1569969-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add below features support for both TJA1100 and TJA1101 cards:
- Add MII and RMII mode support.
- Add REF_CLK input/output support for RMII mode.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TJA110x REF_CLK can be configured as interface reference clock
intput or output when the RMII mode enabled. This patch add the
property to make the REF_CLK can be configurable.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata says:
====================
mlxsw: Introduce modular system support by minimal driver
Vadim Pasternak writes:
This patchset adds line cards support in mlxsw_minimal, which is used
for monitoring purposes on BMC systems. The BMC is connected to the
ASIC over I2C bus, unlike the host CPU that is connected to the ASIC
via PCI bus.
The BMC system needs to be notified whenever line cards become active
or inactive, so that, for example, netdevs will be registered /
unregistered by mlxsw_minimal. However, traps cannot be generated
towards the BMC over the I2C bus. To overcome that, the I2C bus driver
(i.e., mlxsw_i2c) registers an handler for an IRQ that is fired upon
specific system wide changes, like line card activation and
deactivation.
The generated event is handled by mlxsw_core, which checks whether
anything changed in the state of available line cards. If a line card
becomes active or inactive, interested parties such as mlxsw_minimal
are notified via their registered line card event callback.
Patch set overview:
Patches #1 is preparations.
Patches #2-#3 extend mlxsw_core with an infrastructure to handle the
previously mentioned system events.
Patch #4 extends the I2C bus driver to register an handler for the IRQ
fired upon specific system wide changes.
Patches #5-#8 gradually add line cards support in mlxsw_minimal by
dynamically registering / unregistering netdevs for ports found on
line cards, whenever a line card becomes active / inactive.
====================
Link: https://lore.kernel.org/r/cover.1661093502.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement line card operation callbacks got_active() / got_inactive().
The purpose of these callback to create / remove line card ports after
line card is getting active / inactive.
Implement line ports_remove_selected() callback to support line card
un-provisioning flow through 'devlink'.
Add line card operation registration and de-registration APIs.
Add module offset for line card. Offset for main board iz zero.
For line card in slot #n offset is calculated as (#n - 1) multiplied by
maximum modules number.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The interfaces for ports found on line card are created and removed
dynamically after line card is getting active or inactive.
Introduce per line card array with module to port mapping.
For each port get 'slot_index' through PMLP register and set port
mapping for the relevant [slot_index][module] entry.
Split module and port allocation into separate routines.
Split per line card port creation and removing into separate routines.
Motivation to re-use these routines for line card operations.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Perform ports allocation in a separate routine.
Motivation is to re-use this routine for ports found on line cards.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add 'slot_index' field to port structure.
Replace zero slot_index argument with 'slot_index' in 'ethtool'
related APIs.
Add 'slot_index' argument to port initialization and
de-initialization related APIs.
Motivation is to prepare minimal driver for modular system support.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend i2c bus driver with interrupt handler to support system specific
hotplug events, related to line card state change.
Provide system IRQ line for interrupt handler. IRQ line Id could be
provided through the platform data if available, or could be set to the
default value.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add line card system event handler. Register it with core. It is
triggered by system interrupts raised from chassis programmable logic
devices to CPU. The purpose is to handle line card state changes over
I2C bus.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The purpose of system event handler is to handle system interrupts.
Such interrupts are raised to CPU from system programmable logic
devices, upon specific system wide changes, like line card activation
and deactivation.
The purpose is to create an alternative to trap mechanism, which
delivers these events to driver over PCI bus, but not available for
the driver working over I2C bus.
Mechanism is system dependent and applicable only for the systems
equipped with programmable devices with custom logic.
Add APIs for event handler registration and un-registration and API
which should be invoked from the registered callbacks when system
interrupt is raised to CPU.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, each line card is initialized using the following steps:
1. Initializing its various fields (e.g., slot index).
2. Creating the corresponding devlink object.
3. Enabling events (i.e., traps) for changes in line card status.
4. Querying and processing line card status.
Unlike traps, the IRQ that notifies the CPU about line card status
changes cannot be enabled / disabled on a per line card basis.
If a handler is registered before the line cards are initialized, the
handler risks accessing uninitialized memory.
On the other hand, if the handler is registered after initialization,
we risk missing events. For example, in step 4, the driver might see
that a line card is in ready state and will tell the device to enable
it. When enablement is done, the line card will be activated and the
IRQ will be triggered. Since a handler was not registered, the event
will be missed.
Solve this by splitting the initialization sequence into two steps
(1-2 and 3-4). In a subsequent patch, the handler will be registered
between both steps.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide a bit of a brain dump of netlink related information
as documentation. Hopefully this will be useful to people
trying to navigate implementing YAML based parsing in languages
we won't be able to help with.
I started writing this doc while trying to figure out what
it'd take to widen the applicability of YAML to good old rtnl,
but the doc grew beyond that as it usually happens.
In all honesty a lot of this information is new to me as I usually
follow the "copy an existing example, drink to forget" process
of writing netlink user space, so reviews will be much appreciated.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20220819200221.422801-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Subsequent patch will render the kdoc from
include/uapi/linux/netlink.h into Documentation.
We need to fix the warnings. While at it move
the comments on struct nlmsghdr to a proper
kdoc comment.
Link: https://lore.kernel.org/r/20220819200221.422801-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case ftmac100 is used with a DSA switch, Linux wants to set MTU
to 1504 to accommodate for DSA overhead. With the default max_mtu
it leads to the error message:
ftmac100 92000000.mac eth0: error -22 setting MTU to 1504 to include DSA overhead
ftmac100 supports packet length 1518 (MAX_PKT_SIZE constant), so it is
safe to report it in max_mtu.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220821160844.474277-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
DSA changes for multiple CPU ports (part 3)
Those who have been following part 1:
https://patchwork.kernel.org/project/netdevbpf/cover/20220511095020.562461-1-vladimir.oltean@nxp.com/
and part 2:
https://patchwork.kernel.org/project/netdevbpf/cover/20220521213743.2735445-1-vladimir.oltean@nxp.com/
will know that I am trying to enable the second internal port pair from
the NXP LS1028A Felix switch for DSA-tagged traffic via "ocelot-8021q".
This series represents part 3 of that effort.
Covered here are some preparations in DSA for handling multiple DSA
masters:
- when changing the tagging protocol via sysfs
- when the masters go down
as well as preparation for monitoring the upper devices of a DSA master
(to support DSA masters under a LAG).
There are also 2 small preparations for the ocelot driver, for the case
where multiple tag_8021q CPU ports are used in a LAG. Both those changes
have to do with PGID forwarding domains.
Compared to v1, the patches were trimmed down to just another
preparation stage, and the UAPI changes were pushed further out to part 4.
https://patchwork.kernel.org/project/netdevbpf/cover/20220523104256.3556016-1-olteanv@gmail.com/
Compared to v2, I had to export a symbol I forgot to
(ocelot_port_teardown_dsa_8021q_cpu), to avoid a build breakage when the
felix and seville drivers are built as modules.
====================
Link: https://lore.kernel.org/r/20220819174820.3585002-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently when we have 2 CPU ports configured for DSA tag_8021q mode and
we put them in a LAG, a PGID dump looks like this:
PGID_SRC[0] = ports 4,
PGID_SRC[1] = ports 4,
PGID_SRC[2] = ports 4,
PGID_SRC[3] = ports 4,
PGID_SRC[4] = ports 0, 1, 2, 3, 4, 5,
PGID_SRC[5] = no ports
(ports 0-3 are user ports, ports 4 and 5 are CPU ports)
There are 2 problems with the configuration above:
- user ports should enable forwarding towards both CPU ports, not just 4,
and the aggregation PGIDs should prune one CPU port or the other from
the destination port mask, based on a hash computed from packet headers.
- CPU ports should not be allowed to forward towards themselves and also
not towards other ports in the same LAG as themselves
The first problem requires fixing up the PGID_SRC of user ports, when
ocelot_port_assigned_dsa_8021q_cpu_mask() is called. We need to say that
when a user port is assigned to a tag_8021q CPU port and that port is in
a LAG, it should forward towards all ports in that LAG.
The second problem requires fixing up the PGID_SRC of port 4, to remove
ports 4 and 5 (in a LAG) from the allowed destinations.
After this change, the PGID source masks look as follows:
PGID_SRC[0] = ports 4, 5,
PGID_SRC[1] = ports 4, 5,
PGID_SRC[2] = ports 4, 5,
PGID_SRC[3] = ports 4, 5,
PGID_SRC[4] = ports 0, 1, 2, 3,
PGID_SRC[5] = no ports
Note that PGID_SRC[5] still looks weird (it should say "0, 1, 2, 3" just
like PGID_SRC[4] does), but I've tested forwarding through this CPU port
and it doesn't seem like anything is affected (it appears that PGID_SRC[4]
is being looked up on forwarding from the CPU, since both ports 4 and 5
have logical port ID 4). The reason why it looks weird is because
we've never called ocelot_port_assign_dsa_8021q_cpu() for any user port
towards port 5 (all user ports are assigned to port 4 which is in a LAG
with 5).
Since things aren't broken, I'm willing to leave it like that for now
and just document the oddity.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This is a partial revert of commit c295f9831f ("net: mscc: ocelot:
switch from {,un}set to {,un}assign for tag_8021q CPU ports"), because
as it turns out, this isn't how tag_8021q CPU ports under a LAG are
supposed to work.
Under that scenario, all user ports are "assigned" to the single
tag_8021q CPU port represented by the logical port corresponding to the
bonding interface. So one CPU port in a LAG would have is_dsa_8021q_cpu
set to true (the one whose physical port ID is equal to the logical port
ID), and the other one to false.
In turn, this makes 2 undesirable things happen:
(1) PGID_CPU contains only the first physical CPU port, rather than both
(2) only the first CPU port will be added to the private VLANs used by
ocelot for VLAN-unaware bridging
To make the driver behave in the same way for both bonded CPU ports, we
need to bring back the old concept of setting up a port as a tag_8021q
CPU port, and this is what deals with VLAN membership and PGID_CPU
updating. But we also need the CPU port "assignment" (the user to CPU
port affinity), and this is what updates the PGID_SRC forwarding rules.
All DSA CPU ports are statically configured for tag_8021q mode when the
tagging protocol is changed to ocelot-8021q. User ports are "assigned"
to one CPU port or the other dynamically (this will be handled by a
future change).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
More logic will be added to dsa_tree_setup_master() and
dsa_tree_teardown_master() in upcoming changes.
Reduce the indentation by one level in these functions by introducing
and using a dedicated iterator for CPU ports of a tree.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The fact that the tagging protocol is set and queried from the
/sys/class/net/<dsa-master>/dsa/tagging file is a bit of a quirk from
the single CPU port days which isn't aging very well now that DSA can
have more than a single CPU port. This is because the tagging protocol
is a switch property, yet in the presence of multiple CPU ports it can
be queried and set from multiple sysfs files, all of which are handled
by the same implementation.
The current logic ensures that the net device whose sysfs file we're
changing the tagging protocol through must be down. That net device is
the DSA master, and this is fine for single DSA master / CPU port setups.
But exactly because the tagging protocol is per switch [ tree, in fact ]
and not per DSA master, this isn't fine any longer with multiple CPU
ports, and we must iterate through the tree and find all DSA masters,
and make sure that all of them are down.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
