When RAID10 supports reshape it will need a 'previous' and a 'current'
geometry, so introduce that here.
Use the 'prev' geometry when before the reshape_position, and the
current 'geo' when beyond it. At other times, use both as
appropriate.
For now, both are identical (And reshape_position is never set).
When we use the 'prev' geometry, we must use the old data_offset.
When we use the current (And a reshape is happening) we must use
the new_data_offset.
Signed-off-by: NeilBrown <neilb@suse.de>
We will shortly be adding reshape support for RAID10 which will
require it having 2 concurrent geometries (before and after).
To make that easier, collect most geometry fields into 'struct geom'
and access them from there. Then we will more easily be able to add
a second set of fields.
Note that 'copies' is not in this struct and so cannot be changed.
There is little need to change this number and doing so is a lot
more difficult as it requires reallocating more things.
So leave it out for now.
Signed-off-by: NeilBrown <neilb@suse.de>
Allow each slot in the RAID10 to have 2 devices, the want_replacement
and the replacement.
Also an r10bio to have 2 bios, and for resync/recovery allocate the
second bio if there are any replacement devices.
Signed-off-by: NeilBrown <neilb@suse.de>
RAID1 and RAID10 handle write requests by queuing them for handling by
a separate thread. This is because when a write-intent-bitmap is
active we might need to update the bitmap first, so it is good to
queue a lot of writes, then do one big bitmap update for them all.
However writeback request devices to appear to be congested after a
while so it can make some guesstimate of throughput. The infinite
queue defeats that (note that RAID5 has already has a finite queue so
it doesn't suffer from this problem).
So impose a limit on the number of pending write requests. By default
it is 1024 which seems to be generally suitable. Make it configurable
via module option just in case someone finds a regression.
Signed-off-by: NeilBrown <neilb@suse.de>
The typedefs are just annoying. 'mdk' probably refers to 'md_k.h'
which used to be an include file that defined this thing.
Signed-off-by: NeilBrown <neilb@suse.de>
When we get a write error (in the data area, not in metadata),
update the badblock log rather than failing the whole device.
As the write may well be many blocks, we trying writing each
block individually and only log the ones which fail.
Signed-off-by: NeilBrown <neilb@suse.de>
If we succeed in writing to a block that was recorded as
being bad, we clear the bad-block record.
This requires some delayed handling as the bad-block-list update has
to happen in process-context.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch just covers the basic read path:
1/ read_balance needs to check for badblocks, and return not only
the chosen slot, but also how many good blocks are available
there.
2/ read submission must be ready to issue multiple reads to
different devices as different bad blocks on different devices
could mean that a single large read cannot be served by any one
device, but can still be served by the array.
This requires keeping count of the number of outstanding requests
per bio. This count is stored in 'bi_phys_segments'
On read error we currently just fail the request if another target
cannot handle the whole request. Next patch refines that a bit.
Signed-off-by: NeilBrown <neilb@suse.de>
When we get a read error during recovery, RAID10 previously
arranged for the recovering device to appear to fail so that
the recovery stops and doesn't restart. This is misleading and wrong.
Instead, make use of the new recovery_disabled handling and mark
the target device and having recovery disabled.
Add appropriate checks in add_disk and remove_disk so that devices
are removed and not re-added when recovery is disabled.
Signed-off-by: NeilBrown <neilb@suse.de>
Most array level changes leave the list of devices largely unchanged,
possibly causing one at the end to become redundant.
However conversions between RAID0 and RAID10 need to renumber
all devices (except 0).
This renumbering is currently being done in the ->run method when the
new personality takes over. However this is too late as the common
code in md.c might already have invalidated some of the devices if
they had a ->raid_disk number that appeared to high.
Moving it into the ->takeover method is too early as the array is
still active at that time and wrong ->raid_disk numbers could cause
confusion.
So add a ->new_raid_disk field to mdk_rdev_s and use it to communicate
the new raid_disk number.
Now the common code knows exactly which devices need to be renumbered,
and which can be invalidated, and can do it all at a convenient time
when the array is suspend.
It can also update some symlinks in sysfs which previously were not be
updated correctly.
Reported-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Having a macro just to cast a void* isn't really helpful.
I would must rather see that we are simply de-referencing ->private,
than have to know what the macro does.
So open code the macro everywhere and remove the pointless cast.
Signed-off-by: NeilBrown <neilb@suse.de>
This makes the includes more explicit, and is preparation for moving
md_k.h to drivers/md/md.h
Remove include/raid/md.h as its only remaining use was to #include
other files.
Signed-off-by: NeilBrown <neilb@suse.de>
Move the headers with the local structures for the disciplines and
bitmap.h into drivers/md/ so that they are more easily grepable for
hacking and not far away. md.h is left where it is for now as there
are some uses from the outside.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
