Some drivers may be performing most of Tx/Rx
aggregation on their own (e.g. in firmware)
including AddBa/DelBa negotiations but may
otherwise require Rx reordering assistance.
The patch exports 2 new functions for establishing
Rx aggregation sessions in assumption device
driver has taken care of the necessary
negotiations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[fix endian bug]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (e.g. ath10k) report A-MSDU subframes
individually with identical seqno. The A-MPDU Rx
reorder code did not account for that which made
it practically unusable with drivers using
RX_FLAG_AMSDU_MORE because it would end up
dropping a lot of frames resulting in confusion in
upper network transport layers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The csa_active flag was added in sdata a while ago and made
IEEE80211_STA_CSA_RECEIVED redundant. The new flag is also used to
mark when CSA is ongoing on other iftypes and took over the old one as
the preferred method for checking whether we're in the middle of a
channel switch. Remove the old, redundant flag.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can only be a station for TDLS connections. Also fix a bug where
a delayed work could be left scheduled if the station interface was
brought down during TDLS setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If QoS is supported by the card, add an appropriate IE to TDLS setup-
request and setup-response frames.
Consolidate the setting of the WMM info IE across mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel switch finalization is now 2-step. First
step is when driver calls chswitch_done(), the
other is when reservation is actually finalized
(which be defered for in-place reservation).
It is now safe to call ieee80211_chswitch_done()
more than once.
Also remove the ieee80211_vif_change_channel()
because it is no longer used.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Multi-vif in-place reservations happen when
it is impossible to allocate more channel contexts
as indicated by interface combinations.
Such reservations are not finalized until all
assigned interfaces are ready.
This still doesn't handle all possible cases
(i.e. degradation of number of channels) properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (such as iwlmvm) can handle multiple bands in a single
HW scan request. Add a HW flag to indicate that the driver support
this. To hold the required data, create a separate structure for
HW scan request that holds cfg scan request and data about
different parts of the scan IEs.
As this changes the mac80211 API, update all drivers using it to
use the correct new function type/argument.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the spec mandates, flush data in the AP path before transmitting the
first setup frame. Data packets transmitted during setup are already
dropped in the Tx path.
For the teardown flow, flush all packets in the direct path before
transmitting the teardown frame. Un-authorize the peer sta after teardown
is sent, forcing all subsequent Tx to the peer through the AP.
Make sure to flush the queues when disabling the link to get the
teardown packet out.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
[adjust to Luca's new quuee API and stop only vif queues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Fix dependent drivers - mwifiex and mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When setting up a TDLS session, register a delayed work to remove
the peer if setup times out. Prevent concurrent setups to support this
capacity.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of stopping all the hardware queues during channel switch,
which is especially bad when we have large CSA counts, stop only the
queues that are assigned to the vif that is performing the channel
switch.
Additionally, check for (sdata->csa_block_tx) instead of calling
ieee80211_csa_needs_block_tx(), which can now be removed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases we may want to stop the queues of a single vif (for
instance during a channel-switch). Add a function that stops all the
queues that are assigned to a vif. If a queue is assigned to more
than one vif, the corresponding netdev subqueue of the other vif(s)
will also be stopped. If the HW doesn't set the
IEEE80211_HW_QUEUE_CONTROL flag, then all queues are stopped.
Also add a corresponding function to wake the queues of a vif back.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes different vifs may be stopping the queues for the same
reason (e.g. when several interfaces are performing a channel switch).
Instead of using a bitmask for the reasons, use an integer that holds
a refcount instead. In order to keep it backwards compatible,
introduce a boolean in some functions that tell us whether the queue
stopping should be refcounted or not. For now, use not refcounted for
all calls to keep it functionally the same as before.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having csa counters part of beacon and probe_resp
structures makes it easier to get rid of possible
races between setting a beacon and updating
counters on SMP systems by guaranteeing counters
are always consistent against given beacon struct.
While at it relax WARN_ON into WARN_ON_ONCE to
prevent spamming logs and racing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[remove pointless array check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, cfg80211 tries to implement ethtool, but that doesn't
really scale well, with all the different operations. Make the
lower-level driver responsible for it, which currently only has
an effect on mac80211. It will similarly not scale well at that
level though, since mac80211 also has many drivers.
To cleanly implement this in mac80211, introduce a new file and
move some code to appropriate places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the beacon CSA counters part of ieee80211_mutable_offsets and don't
decrement CSA counters when generating a beacon template. This permits the
driver to offload the CSA counters handling. Since mac80211 updates the probe
responses with the correct counter, the driver should sync the counter's value
with mac80211 using ieee80211_csa_update_counter function.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support up to IEEE80211_MAX_CSA_COUNTERS_NUM csa counters.
This is defined to be 2 now, to support both CSA and eCSA
counters.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Track current csa counter value and use it
to update mgmt frames at the provided offsets.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni reported that if a remain-on-channel was active on the
same channel as the current operating channel, then the ROC
would start, but any frames transmitted using mgmt-tx on the
same channel would get delayed until after the ROC.
The reason for this is that the ROC starts, but doesn't have
any handling for "remain on the same channel", so it stops
the interface queues. The later mgmt-tx then puts the frame
on the interface queues (since it's on the current operating
channel) and thus they get delayed until after the ROC.
To fix this, add some logic to handle remaining on the same
channel specially and not stop the queues etc. in this case.
This not only fixes the bug but also improves behaviour in
this case as data frames etc. can continue to flow.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Tested-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver fails during HW restart or resume, the whole
stack goes into a very confused state with interfaces being
up while the hardware is down etc.
Address this by shutting down everything; we'll run into a
lot of warnings in the process but that's better than having
the whole stack get messed up.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible for tx queues to be stuck stopped
if AP CSA finalization failed. In that case
neither stop_ap nor do_stop woke the queues up.
This means it was impossible to perform tx at all
until driver was reloaded or a successful CSA was
performed later.
It was possible to solve this in a simpler manner
however this is more robust and future proof
(having multi-vif CSA in mind).
New sdata->csa_block_tx is introduced to keep
track of which interfaces requested tx to be
blocked for CSA. This is required because mac80211
stops all tx queues for that purpose. This means
queues must be awoken only when last tx-blocking
CSA interface is finished.
It is still possible to have tx queues stopped
after CSA failure but as soon as offending
interfaces are stopped from userspace (stop_ap or
ifdown) tx queues are woken up properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With new additions planned, this code is getting too big for cfg.c.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It doesn't make much sense to store refcount in
the chanctx structure. One still needs to hold
chanctx_mtx to get the value safely. Besides,
refcount isn't on performance critical paths.
This will make implementing chanctx reservation
refcounting a little easier.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be useful. Provides a more straghtforward
way to iterate over interfaces taking part in
chanctx reservation and allows tracking chanctx
usage explicitly.
The structure is protected by local->chanctx_mtx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be useful. Provides a more straghtforward
way to iterate over interfaces bound to a given
chanctx and allows tracking chanctx usage
explicitly.
The structure is protected by local->chanctx_mtx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Initial chanctx reservation code wasn't aware of
radar detection requirements. This is necessary
for chanctx reservations to be used for channel
switching in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The utility function has no uses yet. It is aimed
at future chanctx reservation management and
channel switching.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support channel switch with multiple vifs and multiple
contexts, we implement a concept of channel context reservation. This
allows us to reserve a channel context to be used later.
The reservation functionality is not tied directly to channel switch
and may be used in other situations (eg. reserving a channel context
during IBSS join).
We first check if an existing compatible context exists and if it
does, we reserve it. If there is no compatible context we create a
new one and reserve it.
Additionally, split ieee80211_vif_copy_chanctx_to_vlans() so we can
call it while already holding the chanctx mutex.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was impossible to change chanctx of master AP
for AP VLANs because the copy function requires
RTNL which can't be simply taken in mac80211 code
due to possible deadlocks.
This is required for future chanctx reservation
that re-bind vifs to new chanctx. This requires
safe AP VLAN iteration without RTNL.
Now VLANs can be iterated while holding either
RTNL or local->mtx because the list is modified
while holding both of these locks.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the counting part of the interface combination check from
cfg80211 to mac80211.
This is needed to simplify locking when the driver has to perform a
combination check by itself (eg. with channel-switch).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since Stanislaw's patch removing the quiescing code, mac80211 had
a race regarding suspend vs. authentication: as cfg80211 doesn't
track authentication attempts, it can't abort them. Therefore the
attempts may be kept running while suspending, which can lead to
all kinds of issues, in at least some cases causing an error in
iwlmvm firmware.
Fix this by aborting the authentication attempt when suspending.
Cc: stable@vger.kernel.org
Fixes: 12e7f51702 ("mac80211: cleanup generic suspend/resume procedures")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Consider the following (relatively unlikely) scenario:
1) station goes to sleep while frames are buffered in driver
2) driver blocks wakeup (until no more frames are buffered)
3) station wakes up again
4) driver unblocks wakeup
In this case, the current mac80211 code will do the following:
1) WLAN_STA_PS_STA set
2) WLAN_STA_PS_DRIVER set
3) - nothing -
4) WLAN_STA_PS_DRIVER cleared
As a result, no frames will be delivered to the client, even
though it is awake, until it sends another frame to us that
triggers ieee80211_sta_ps_deliver_wakeup() in sta_ps_end().
Since we now take the PS spinlock, we can fix this while at
the same time removing the complexity with the pending skb
queue function. This was broken since my commit 50a9432dae
("mac80211: fix powersaving clients races") due to removing
the clearing of WLAN_STA_PS_STA in the RX path.
While at it, fix a cleanup path issue when a station is
removed while the driver is still blocking its wakeup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NAPI was originally added to mac80211 a long time ago (by John in
commit 4e6cbfd09c in July 2010), but then removed years later
(by Stanislaw in commit 30c97120c6 in February 2013). No driver
ever used it, so that was fine.
Now I'm adding support for NAPI to our driver, so add some code
to mac80211 again to support NAPI. John was originally wrapping
some (but not nearly all NAPI-related functions), but that doesn't
scale very well with the number of functions that are there, some
of which are even only inlines. Thus, instead of doing that, let
the drivers manage the NAPI struct, except for napi_add() which is
needed so mac80211 knows how to call napi_gro_receive().
Also remove some no longer needed definitions that were left when
NAPI support was removed.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update the operating mode field is needed when an association
request contains the operating mode notification element and
it's not just changed later on the fly.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
[clarify commit log, comments & fix whitespace]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wiphy privid (to identify wiphys) and the cfg80211
ops should both be const, so change them to be.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A beacon should never have a Channel Switch Announcement information
element with a count of 0, because a count of 1 means switch just
before the next beacon. So, if a count of 0 was valid in a beacon, it
would have been transmitted in the next channel already, which is
useless. A CSA count equal to zero is only meaningful in action
frames or probe_responses.
Fix the ieee80211_csa_is_complete() and ieee80211_update_csa()
functions accordingly.
With a CSA count of 0, we won't transmit any CSA beacons, because the
switch will happen before the next TBTT. To avoid extra work and
potential confusion in the drivers, complete the CSA immediately,
instead of waiting for the driver to call ieee80211_csa_finish().
To keep things simpler, we also switch immediately when the CSA count
is 1, while in theory we should delay the switch until just before the
next TBTT.
Additionally, move the ieee80211_csa_finish() function to cfg.c,
where it makes more sense.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor ieee80211_mesh_process_chanswitch() to use
ieee80211_channel_switch() and avoid code duplication.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On starting a mesh or AP BSS, the interface dtim_count
countdown should match that of the driver TSF.
Signed-off-by: Thomas Pedersen <twpedersen@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Its address is used as an unsigned long *, so make sure
that the tim u8 array is properly aligned.
Signed-off-by: Joe Perches <joe@perches.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function is only used in one file, so move it up a
bit to avoid forward declarations and make it static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor ieee80211_ibss_process_chanswitch() to use
ieee80211_channel_switch() and avoid code duplication.
Tested by: Simon Wunderlich <sw@simonwunderlich.de>
Acked by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This regression was introduced in "mac80211: cache mesh
beacon".
mesh_sync_offset_adjust_tbtt() was assuming that the
beacon would be rebuilt in every single pre-tbtt
interrupt, but now the beacon update happens on the
workqueue, and it must be ready for immediate delivery to
the driver.
Save a pointer to the meshconf IE in the beacon_data (this
works because both the IE pointer and beacon buffer are
protected by the same rcu_{dereference,assign_pointer}())
for quick updates during pre-tbtt. This is faster and a
little prettier than iterating over the elements to find
the meshconf IE every time.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Keep the sched scan req when starting sched scan, and reschedule
it in case of HW restart during sched scan.
The upper layer don't have to know about the restart.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function is not used anywhere else than in cfg.c, so there's no
need to export it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
