Both QSPI and GPMC-NAND share the same Pin (A8) from the SoC for Chip Select
functionality. So both can't be enabled simultaneously.
Disable QSPI node to prevent the pin conflict as well as
be similar to 3.12 release.
CC: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For NAND read & write wait pin monitoring must be kept disabled as the
wait pin is only used to indicate NAND device ready status and not to
extend each read/write cycle.
So don't print a warning if wait pin is specified while read/write
monitoring is not in the device tree.
Sanity check wait pin number irrespective if read/write monitoring is
set or not.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
Add gpmc wait pin information as the NAND uses wait pin 0
for device ready indication.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
This patch also gets rid of the below warning when NAND is
accessed for the first time.
omap_l3_noc 44000000.ocp: L3 application error: target 13 mod:1 (unclearable)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am437x-gp-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am43x-epos-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On the GP EVM, the ambient light sensor is limited to 100KHz on the
I2C bus.
So use 100kHz for I2C on the GP EVM due to this limitation on the
ambient light sensor.
Reported-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The 8th NAND partition should be named "NAND.u-boot-env.backup1"
instead of "NAND.u-boot-env". This is to be consistent with other
TI boards as well as u-boot.
CC: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C3 pins are taken from pads E21 (GPIO6_14) and
F20 (GPIO6_15). Use the right pinmux register and mode.
Also set the I2C3 bus frequency to a safer 400KHz than
3.4Mhz.
CC: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The arm64 interrupt migration code on cpu offline calls
irqchip.irq_set_affinity() with the argument force=true. Originally
this argument had no effect because it was not used by any interrupt
chip driver and there was no semantics defined.
This changed with commit 01f8fa4f01 ("genirq: Allow forcing cpu
affinity of interrupts") which made the force argument useful to route
interrupts to not yet online cpus without checking the target cpu
against the cpu online mask. The following commit ffde1de640
("irqchip: gic: Support forced affinity setting") implemented this for
the GIC interrupt controller.
As a consequence the cpu offline irq migration fails if CPU0 is
offlined, because CPU0 is still set in the affinity mask and the
validation against cpu online mask is skipped to the force argument
being true. The following first_cpu(mask) selection always selects
CPU0 as the target.
Commit 601c942176d8("arm64: use cpu_online_mask when using forced
irq_set_affinity") intended to fix the above mentioned issue but
introduced another issue where affinity can be migrated to a wrong
CPU due to unconditional copy of cpu_online_mask.
As with for arm, solve the issue by calling irq_set_affinity() with
force=false from the CPU offline irq migration code so the GIC driver
validates the affinity mask against CPU online mask and therefore
removes CPU0 from the possible target candidates. Also revert the
changes done in the commit 601c942176 as it's no longer needed.
Tested on Juno platform.
Fixes: 601c942176d8("arm64: use cpu_online_mask when using forced
irq_set_affinity")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> # 3.10.x
Signed-off-by: Will Deacon <will.deacon@arm.com>
Another handful of arm64 fixes here:
- A few fixes for real issues found by smatch (after Dan's talk at KS)
- Revert the /proc/cpuinfo changes merged during the merge window.
We've opened a can of worms here, so we need to find out where we
stand before we change this interface.
- Implement KSTK_ESP for compat tasks, otherwise 32-bit Android gets
confused wondering where its [stack] has gone
- Misc fixes (fpsimd context handling, crypto, ...)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ibHT
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 fixes from Will Deacon:
"Another handful of arm64 fixes here. They address some issues found
by running smatch on the arch code (ignoring the false positives) and
also stop 32-bit Android from losing track of its stack.
There's one additional irq migration fix in the pipeline, but it came
in after I'd tagged and tested this set.
- a few fixes for real issues found by smatch (after Dan's talk at KS)
- revert the /proc/cpuinfo changes merged during the merge window.
We've opened a can of worms here, so we need to find out where we
stand before we change this interface.
- implement KSTK_ESP for compat tasks, otherwise 32-bit Android gets
confused wondering where its [stack] has gone
- misc fixes (fpsimd context handling, crypto, ...)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Revert "arm64: cpuinfo: print info for all CPUs"
arm64: fix bug for reloading FPSIMD state after cpu power off
arm64: report correct stack pointer in KSTK_ESP for compat tasks
arm64: Add brackets around user_stack_pointer()
arm64: perf: don't rely on layout of pt_regs when grabbing sp or pc
arm64: ptrace: fix compat reg getter/setter return values
arm64: ptrace: fix compat hardware watchpoint reporting
arm64: Remove unused variable in head.S
arm64/crypto: remove redundant update of data
fc95ca7284 introduces a memset in
kvmppc_alloc_hpt since the general CMA doesn't clear the memory it
allocates.
However, the size argument passed to memset is computed from a signed value
and its signed bit is extended by the cast the compiler is doing. This lead
to extremely large size value when dealing with order value >= 31, and
almost all the memory following the allocated space is cleaned. As a
consequence, the system is panicing and may even fail spawning the kdump
kernel.
This fix makes use of an unsigned value for the memset's size argument to
avoid sign extension. Among this fix, another shift operation which may
lead to signed extended value too is also fixed.
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The quite-recently-added analog-tv-connector bindings say that the
compatible string for composite video connector is
"composite-connector". That string is also used in the omap3-n900.dts
file. However, the connector driver uses "composite-video-connector", so
this has never worked.
While changing the driver's compatible string to "composite-connector"
would be safer, as published DT bindings should not be changed, I'd
rather fix the bindings in this case for two reasons:
* composite-connector is a bit too generic name, as it doesn't even hint
at video.
* it's clear that this has never worked, which means no one has used
those bindings, which should make it safe to change this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Analogous to commit 8858d88a25
that fixed commit 70b41abc15
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.
For some reason I forgot to fix this on the Snowball. Fix
this up by marking the node disabled again.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
commit 0944fe3f4a ("s390/mm: implement software referenced bits")
triggered another paging/storage key corruption. There is an
unhandled invalid->valid pte change where we have to set the real
storage key from the pgste.
When doing paging a guest page might be swapcache or swap and when
faulted in it might be read-only and due to a parallel scan old.
An do_wp_page will make it writeable and young. Due to software
reference tracking this page was invalid and now becomes valid.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@vger.kernel.org # v3.12+
Since 3.12 or more precisely commit 0944fe3f4a ("s390/mm:
implement software referenced bits") guest storage keys get
corrupted during paging. This commit added another valid->invalid
translation for page tables - namely ptep_test_and_clear_young.
We have to transfer the storage key into the pgste in that case.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@vger.kernel.org # v3.12+
It turns out that vendors are relying on the format of /proc/cpuinfo,
and we've even spotted out-of-tree hacks attempting to make it look
identical to the format used by arch/arm/. That means we can't afford to
churn this interface in mainline, so revert the recent reformatting of
the file for arm64 pending discussions on the list to find out what
people actually want.
This reverts commit d7a49086f2.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now arm64 defers reloading FPSIMD state, but this optimization also
introduces the bug after cpu resume back from low power mode.
The reason is after the cpu has been powered off, s/w need set the
cpu's fpsimd_last_state to NULL so that it will force to reload
FPSIMD state for the thread, otherwise there has the chance to meet
the condition for both the task's fpsimd_state.cpu field contains the
id of the current cpu, and the cpu's fpsimd_last_state per-cpu variable
points to the task's fpsimd_state, so finally kernel will skip to reload
the context during it return back to userland.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Leo Yan <leoy@marvell.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 9eabc99a63 causes following build error when
IOAPIC is disabled.
arch/x86/pci/irq.c: In function 'pirq_disable_irq':
>> arch/x86/pci/irq.c:1259:2: error: implicit declaration of function 'mp_should_keep_irq' [-Werror=implicit-function-declaration]
if (io_apic_assign_pci_irqs && !mp_should_keep_irq(&dev->dev) &&
^
cc1: some warnings being treated as errors
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1409382916-10649-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The explicit NULL pointer check on the timespec argument is only
required for clock_getres but not for clock_gettime.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the loadparm is only supported for CCW IPL. But also for SCSI
IPL it can be specified either on the HMC load panel respectively
z/VM console or via diagnose 308.
So fix this for SCSI and add the required sysfs attributes for reading the
IPL loadparm and for setting the loadparm for re-IPL.
With this patch the following two sysfs attributes are introduced:
- /sys/firmware/ipl/loadparm (for system that have been IPLed from SCSI)
- /sys/firmware/reipl/fcp/loadparm
Because the loadparm is now available for SCSI and CCW it is moved
now from "struct ipl_block_ccw" to the generic "struct ipl_list_hdr".
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- support highmem on cores with aliasing data cache. Enable highmem on kc705
by default;
- simplify addition of new core variants (no need to modify Kconfig /
Makefiles);
- improve robustness of unaligned access handler and its interaction with
window overflow/underflow exception handlers;
- deprecate atomic and spill registers syscalls;
- clean up Kconfig: remove orphan MATH_EMULATION, sort 'select' statements;
- wire up renameat2 syscall.
Various fixes:
- fix address checks in dma_{alloc,free}_coherent (runtime BUG);
- fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage);
- fix TLBTEMP_BASE_2 region handling in fast_second_level_miss (runtime
unrecoverable exception);
- fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace register
clobbering);
- fix kernel/user jump out of fast_unaligned (potential runtime unrecoverabl
exception);
- replace termios IOCTL code definitions with constants (userspace build
breakage).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mAYX
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux
Pull Xtensa updates from Chris Zankel:
"Xtensa improvements for 3.17:
- support highmem on cores with aliasing data cache. Enable highmem
on kc705 by default
- simplify addition of new core variants (no need to modify Kconfig /
Makefiles)
- improve robustness of unaligned access handler and its interaction
with window overflow/underflow exception handlers
- deprecate atomic and spill registers syscalls
- clean up Kconfig: remove orphan MATH_EMULATION, sort 'select'
statements
- wire up renameat2 syscall.
Various fixes:
- fix address checks in dma_{alloc,free}_coherent (runtime BUG)
- fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage)
- fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
(runtime unrecoverable exception)
- fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace
register clobbering)
- fix kernel/user jump out of fast_unaligned (potential runtime
unrecoverabl exception)
- replace termios IOCTL code definitions with constants (userspace
build breakage)"
* tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux: (25 commits)
xtensa: deprecate fast_xtensa and fast_spill_registers syscalls
xtensa: don't allow overflow/underflow on unaligned stack
xtensa: fix a6 and a7 handling in fast_syscall_xtensa
xtensa: allow single-stepping through unaligned load/store
xtensa: move invalid unaligned instruction handler closer to its users
xtensa: make fast_unaligned store restartable
xtensa: add double exception fixup handler for fast_unaligned
xtensa: fix kernel/user jump out of fast_unaligned
xtensa: configure kc705 for highmem
xtensa: support highmem in aliasing cache flushing code
xtensa: support aliasing cache in kmap
xtensa: support aliasing cache in k[un]map_atomic
xtensa: implement clear_user_highpage and copy_user_highpage
xtensa: fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
xtensa: allow fixmap and kmap span more than one page table
xtensa: make fixmap region addressing grow with index
xtensa: fix access to THREAD_RA/THREAD_SP/THREAD_DS
xtensa: add renameat2 syscall
xtensa: fix address checks in dma_{alloc,free}_coherent
xtensa: replace IOCTL code definitions with constants
...
unicore32 builds fail with
arch/unicore32/kernel/signal.c: In function ‘setup_frame’:
arch/unicore32/kernel/signal.c:257: error: ‘usig’ undeclared (first use in this function)
arch/unicore32/kernel/signal.c:279: error: ‘usig’ undeclared (first use in this function)
arch/unicore32/kernel/signal.c: In function ‘handle_signal’:
arch/unicore32/kernel/signal.c:306: warning: unused variable ‘tsk’
arch/unicore32/kernel/signal.c: In function ‘do_signal’:
arch/unicore32/kernel/signal.c:376: error: implicit declaration of function ‘get_signsl’
make[1]: *** [arch/unicore32/kernel/signal.o] Error 1
make: *** [arch/unicore32/kernel/signal.o] Error 2
Bisect points to commit 649671c90e ("unicore32: Use get_signal()
signal_setup_done()").
This code never even compiled. Reverting the patch does not work, since
previously used functions no longer exist, so try to fix it up. Compile
tested only.
Fixes: 649671c90e ("unicore32: Use get_signal() signal_setup_done()")
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM fixes from Russell King:
"Various assorted fixes:
- a couple of patches from Mark Rutland to resolve an errata with
Cortex-A15 CPUs.
- fix cpuidle for the CPU part ID changes in the last merge window
- add support for a relocation which ARM binutils is generating in
some circumstances"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8130/1: cpuidle/cpuidle-big_little: fix reading cpu id part number
ARM: 8129/1: errata: work around Cortex-A15 erratum 830321 using dummy strex
ARM: 8128/1: abort: don't clear the exclusive monitors
ARM: 8127/1: module: add support for R_ARM_TARGET1 relocations
Here's the weekly batch of fixes from arm-soc.
The delta is a largeish negative delta, due to revert of SMP support for Broadcom's
STB SoC -- it was accidentally merged before some issues had been addressed, so they
will make a new attempt for 3.18. I didn't see a need for a full revert of the whole
platform due to this, we're keeping the rest enabled.
The rest is mostly:
* A handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
* Some MTD/NAND fixes for OMAP
* Minor DT fixes for shmobile
* Warning fix for UP builds on vexpress/spc
There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
so it can boot. Drivers and the rest had landed for 3.17, and it's small
and isolated so it made sense to pick up now even if it's not a bugfix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/AD8
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's the weekly batch of fixes from arm-soc.
The delta is a largeish negative delta, due to revert of SMP support
for Broadcom's STB SoC -- it was accidentally merged before some
issues had been addressed, so they will make a new attempt for 3.18.
I didn't see a need for a full revert of the whole platform due to
this, we're keeping the rest enabled.
The rest is mostly:
- a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
- some MTD/NAND fixes for OMAP
- minor DT fixes for shmobile
- warning fix for UP builds on vexpress/spc
There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
so it can boot. Drivers and the rest had landed for 3.17, and it's
small and isolated so it made sense to pick up now even if it's not a
bugfix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
vexpress/spc: fix a build warning on array bounds
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
MAINTAINERS: catch special Rockchip code locations
ARM: dts: microsom-ar8035: MDIO pad must be set open drain
ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
ARM: brcmstb: revert SMP support
ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
ARM: dts: Enable UART wake-up events for beagleboard
ARM: dts: Remove twl6030 clk32g "regulator"
ARM: OMAP2+: omap_device: remove warning that clk alias already exists
ARM: OMAP: fix %d confusingly prefixed with 0x in format string
ARM: dts: DRA7: fix interrupt-cells for GPIO
mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
mtd: nand: omap: Revert to using software ECC by default
ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
...
With ARCH_VEXPRESS_SPC option, kernel build has the following
warning:
arch/arm/mach-vexpress/spc.c: In function ‘ve_spc_clk_init’:
arch/arm/mach-vexpress/spc.c:431:38: warning: array subscript is below array bounds [-Warray-bounds]
struct ve_spc_opp *opps = info->opps[cluster];
^
since 'cluster' maybe '-1' in UP system. This patch does a active
checking to fix this issue.
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
are OMAP2+ derivative SoCs. This should be low-risk to existing OMAP
platforms.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5ZS8
-----END PGP SIGNATURE-----
Merge tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
Pull "ARM: OMAP2+: DRA72x/DRA74x basic support" from Tony Lindgren:
Add basic subarchitecture support for the DRA72x and DRA74x. These
are OMAP2+ derivative SoCs. This should be low-risk to existing OMAP
platforms.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/
* tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull x86 fixes from Peter Anvin:
"One patch to avoid assigning interrupts we don't actually have on
non-PC platforms, and two patches that addresses bugs in the new
IOAPIC assignment code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, irq, PCI: Keep IRQ assignment for runtime power management
x86: irq: Fix bug in setting IOAPIC pin attributes
x86: Fix non-PC platform kernel crash on boot due to NULL dereference
Merge patches from Andrew Morton:
"22 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
kexec: purgatory: add clean-up for purgatory directory
Documentation/kdump/kdump.txt: add ARM description
flush_icache_range: export symbol to fix build errors
tools: selftests: fix build issue with make kselftests target
ocfs2: quorum: add a log for node not fenced
ocfs2: o2net: set tcp user timeout to max value
ocfs2: o2net: don't shutdown connection when idle timeout
ocfs2: do not write error flag to user structure we cannot copy from/to
x86/purgatory: use approprate -m64/-32 build flag for arch/x86/purgatory
drivers/rtc/rtc-s5m.c: re-add support for devices without irq specified
xattr: fix check for simultaneous glibc header inclusion
kexec: remove CONFIG_KEXEC dependency on crypto
kexec: create a new config option CONFIG_KEXEC_FILE for new syscall
x86,mm: fix pte_special versus pte_numa
hugetlb_cgroup: use lockdep_assert_held rather than spin_is_locked
mm/zpool: use prefixed module loading
zram: fix incorrect stat with failed_reads
lib: turn CONFIG_STACKTRACE into an actual option.
mm: actually clear pmd_numa before invalidating
memblock, memhotplug: fix wrong type in memblock_find_in_range_node().
...
Without this patch the kexec-purgatory.c and purgatory.ro files are not
removed after make mrproper.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas reported that build of x86_64 kernel was failing for him. He is
using 32bit tool chain.
Problem is that while compiling purgatory, I have not specified -m64
flag. And 32bit tool chain must be assuming -m32 by default.
Following is error message.
(mini) [~/work/linux-2.6] make
scripts/kconfig/conf --silentoldconfig Kconfig
CHK include/config/kernel.release
UPD include/config/kernel.release
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
UPD include/generated/utsrelease.h
CC arch/x86/purgatory/purgatory.o
arch/x86/purgatory/purgatory.c:1:0: error: code model 'large' not supported in
the 32 bit mode
Fix it by explicitly passing appropriate -m64/-m32 build flag for
purgatory.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New system call depends on crypto. As it did not have a separate config
option, CONFIG_KEXEC was modified to select CRYPTO and CRYPTO_SHA256.
But now previous patch introduced a new config option for new syscall.
So CONFIG_KEXEC does not require crypto. Remove that dependency.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently new system call kexec_file_load() and all the associated code
compiles if CONFIG_KEXEC=y. But new syscall also compiles purgatory
code which currently uses gcc option -mcmodel=large. This option seems
to be available only gcc 4.4 onwards.
Hiding new functionality behind a new config option will not break
existing users of old gcc. Those who wish to enable new functionality
will require new gcc. Having said that, I am trying to figure out how
can I move away from using -mcmodel=large but that can take a while.
I think there are other advantages of introducing this new config
option. As this option will be enabled only on x86_64, other arches
don't have to compile generic kexec code which will never be used. This
new code selects CRYPTO=y and CRYPTO_SHA256=y. And all other arches had
to do this for CONFIG_KEXEC. Now with introduction of new config
option, we can remove crypto dependency from other arches.
Now CONFIG_KEXEC_FILE is available only on x86_64. So whereever I had
CONFIG_X86_64 defined, I got rid of that.
For CONFIG_KEXEC_FILE, instead of doing select CRYPTO=y, I changed it to
"depends on CRYPTO=y". This should be safer as "select" is not
recursive.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Tested-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sasha Levin has shown oopses on ffffea0003480048 and ffffea0003480008 at
mm/memory.c:1132, running Trinity on different 3.16-rc-next kernels:
where zap_pte_range() checks page->mapping to see if PageAnon(page).
Those addresses fit struct pages for pfns d2001 and d2000, and in each
dump a register or a stack slot showed d2001730 or d2000730: pte flags
0x730 are PCD ACCESSED PROTNONE SPECIAL IOMAP; and Sasha's e820 map has
a hole between cfffffff and 100000000, which would need special access.
Commit c46a7c817e ("x86: define _PAGE_NUMA by reusing software bits on
the PMD and PTE levels") has broken vm_normal_page(): a PROTNONE SPECIAL
pte no longer passes the pte_special() test, so zap_pte_range() goes on
to try to access a non-existent struct page.
Fix this by refining pte_special() (SPECIAL with PRESENT or PROTNONE) to
complement pte_numa() (SPECIAL with neither PRESENT nor PROTNONE). A
hint that this was a problem was that c46a7c817e added pte_numa() test
to vm_normal_page(), and moved its is_zero_pfn() test from slow to fast
path: This was papering over a pte_special() snag when the zero page was
encountered during zap. This patch reverts vm_normal_page() to how it
was before, relying on pte_special().
It still appears that this patch may be incomplete: aren't there other
places which need to be handling PROTNONE along with PRESENT? For
example, pte_mknuma() clears _PAGE_PRESENT and sets _PAGE_NUMA, but on a
PROT_NONE area, that would make it pte_special(). This is side-stepped
by the fact that NUMA hinting faults skipped PROT_NONE VMAs and there
are no grounds where a NUMA hinting fault on a PROT_NONE VMA would be
interesting.
Fixes: c46a7c817e ("x86: define _PAGE_NUMA by reusing software bits on the PMD and PTE levels")
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: <stable@vger.kernel.org> [3.16]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
write{b,w,l,q}_relaxed are implemented by some architectures in order to
permit memory-mapped I/O writes with weaker barrier semantics than the
non-relaxed variants.
This patch implements these write macros for Alpha, in the same vein as
the relaxed read macros, which are already implemented.
Acked-by: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The KSTK_ESP macro is used to determine the user stack pointer for a
given task. In particular, this is used to to report the '[stack]' VMA
in /proc/self/maps, which is used by Android to determine the stack
location for children of the main thread.
This patch fixes the macro to use user_stack_pointer instead of directly
returning sp. This means that we report w13 instead of sp, since the
former is used as the stack pointer when executing in AArch32 state.
Cc: <stable@vger.kernel.org>
Reported-by: Serban Constantinescu <Serban.Constantinescu@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 5f888a1d33 (ARM64: perf: support dwarf unwinding in compat mode)
changes user_stack_pointer() to return the compat SP for 32-bit tasks
but without brackets around the whole definition, with possible issues
on the call sites (noticed with a subsequent fix for KSTK_ESP).
Fixes: 5f888a1d33 (ARM64: perf: support dwarf unwinding in compat mode)
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now IOAPIC driver dynamically allocates IRQ numbers for IOAPIC pins.
We need to keep IRQ assignment for PCI devices during runtime power
management, otherwise it may cause failure of device wakeups.
Commit 3eec595235 "x86, irq, PCI: Keep IRQ assignment for PCI
devices during suspend/hibernation" has fixed the issue for suspend/
hibernation, we also need the same fix for runtime device sleep too.
Fix: https://bugzilla.kernel.org/show_bug.cgi?id=83271
Reported-and-Tested-by: EmanueL Czirai <amanual@openmailbox.org>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: EmanueL Czirai <amanual@openmailbox.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1409304383-18806-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The architecture specifies that when the processor wakes up from a WFE
or WFI instruction, the instruction is considered complete, however we
currrently return to EL1 (or EL0) at the WFI/WFE instruction itself.
While most guests may not be affected by this because their local
exception handler performs an exception returning setting the event bit
or with an interrupt pending, some guests like UEFI will get wedged due
this little mishap.
Simply skip the instruction when we have completed the emulation.
Cc: <stable@vger.kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
X-Gene u-boot runs in EL2 mode with MMU enabled hence we might
have stale EL2 tlb enteris when we enable EL2 MMU on each host CPU.
This can happen on any ARM/ARM64 board running bootloader in
Hyp-mode (or EL2-mode) with MMU enabled.
This patch ensures that we flush all Hyp-mode (or EL2-mode) TLBs
on each host CPU before enabling Hyp-mode (or EL2-mode) MMU.
Cc: <stable@vger.kernel.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The current perf_regs code relies on sp and pc sitting just off the end
of the pt_regs->regs array. This is ugly and fragile, so this patch
checks for these register explicitly and returns the appropriate field.
Acked-by: Jean Pihet <jean.pihet@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
copy_{to,from}_user return the number of bytes remaining on failure, not
an error code.
This patch returns -EFAULT when the copy operation didn't complete,
rather than expose the number of bytes not copied directly to userspace.
Signed-off-by: Will Deacon <will.deacon@arm.com>
I'm not sure what I was on when I wrote this, but when iterating over
the hardware watchpoint array (hbp_watch_array), our index is off by
ARM_MAX_BRP, so we walk off the end of our thread_struct...
... except, a dodgy condition in the loop means that it never executes
at all (bp cannot be NULL).
This patch fixes the code so that we remove the bp check and use the
correct index for accessing the watchpoint structures.
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
(and a sneaky document addition that slipped from the previous pull-request)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DaB2
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd fixes from Lee Jones:
"Couple of simple fixes due for the 3.17 rcs
(and a sneaky document addition that slipped from the previous
pull-request)"
* tag 'mfd-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: twl4030-power: Fix PM idle pin configuration to not conflict with regulators
mfd: tc3589x: Add device tree bindings
mfd: ab8500-core: Use 'ifdef' for config options
mfd: htc-i2cpld: Fix %d confusingly prefixed with 0x in format string
mfd: omap-usb-host: Fix %d confusingly prefixed with 0x in format string
Commit 43fef47f94 (mfd: twl4030-power: Add a configuration to turn
off oscillator during off-idle) added support for configuring the PMIC
to cut off resources during deeper idle states to save power.
This however caused regression for n900 display power that needed the
PMIC configuration to be disabled with commit d937678ab6 (ARM: dts:
Revert enabling of twl configuration for n900).
Turns out the root cause of the problem is that we must use
TWL4030_RESCONFIG_UNDEF instead of DEV_GRP_NULL to avoid disabling
regulators that may have been enabled before the init function
for twl4030-power.c runs. With TWL4030_RESCONFIG_UNDEF we let the
regulator framework control the regulators like it should. Here we
need to only configure the sys_clken and sys_off_mode triggers for
the regulators that cannot be done by the regulator framework as
it's not running at that point.
This allows us to enable the PMIC configuration for n900.
Fixes: 43fef47f94 (mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle)
Cc: stable@vger.kernel.org # v3.16
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To deal with IPs which are specific to dra74x and dra72x, maintain seperate
ocp interface lists, while keeping the common list for all common IPs.
Move USB OTG SS4 to dra74x only list since its unavailable in
dra72x and is giving an abort during boot. The dra72x only list
is empty for now and a placeholder for future hwmod additions which
are specific to dra72x.
Fixes: d904b38df0 ("ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss")
Reported-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
[paul@pwsan.com: fixed comment style to conform with CodingStyle]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 4bfb358b1d
("ARM: shmobile: Add r8a7791 legacy SDHI clocks")
which was included in v3.15.
This fix does not have any run-time affect at this time.
* ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 9f13ee6f83
("ARM: shmobile: r8a7790: add div4 clocks")
which was included in v3.11.
This fix does not have any run-time affect at this time.
* ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name
This resolves a problem introduced by a0f7e7496d
("ARM: shmobile: sh73a0: add CMT1 clock support for DT")
which was included in v3.17-rc1.
This fix does not have any run-time affect at this time as the clock in
question is used by a SCIF device that is not enabled by default.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT+oE/AAoJENfPZGlqN0++6eYQAK8LStttSbAjBHONrCQpj1/n
fBu+S9RjzYOKLtG4L7pVXOJSFuIiPB03y4IeiFRflIS6TQyopl7DmTZvN/AztIjE
dOamQ+Z2ePrLcNUG1ZNfpEUSxfImOqtcm38R58HRDOnMYTszLOaVxtU0Dre9Y3Me
cYHEN/17PUQWdQ7j5tcaDwXtl4oVjS+1RmzkODKpP2N+1w4l0rcXHEXuNJC6NpW8
1i2CWnlb64hQ0L1tOBVabmUXmlwbasV5dBnysupn3IZHOMO+liNSb9T2RHpvtKSw
U4hu4cZXSGNWoFlWzrs7SoJf1uFF0h5GlrgUm5TGPA1oUPsRzJKRS6D70daElmpi
e5OszD89bs/LftHY4wpcwQ3ic/PSCqMGdF4aFAzVtfseND9tzrK+8aa8GX18bb9R
hGfEeiXzp2EnIEtBMUmrrk0cV9thx1zuwaGoai0P2E82SXbMglrKYVAm0xN3yxRc
77u47S479o7xGSdT2/EBX+EIWnFrGZheT10iPc+aEWRRTxWFf5e10j1i3F1Lw7cL
5P3PNrMUv3s1Vf82gHKfdtlaYZZoMuF3r03ezt2EScg9MDxhytBDHxiokfw7NRdA
OA8IaXuoU4MSXArgkdJ89kzV1AnK8aMGlQY/BXfjPqgPUGRQ8TK/sEDp2I5poMeZ
t2xCtxUvCA39NM/xBDyS
=jurT
-----END PGP SIGNATURE-----
Merge tag 'renesas-clock-fixes-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Renesas ARM Based SoC Clock Fixes For v3.17" from Simon Horman:
* ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 4bfb358b1d
("ARM: shmobile: Add r8a7791 legacy SDHI clocks")
which was included in v3.15.
This fix does not have any run-time affect at this time.
* ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 9f13ee6f83
("ARM: shmobile: r8a7790: add div4 clocks")
which was included in v3.11.
This fix does not have any run-time affect at this time.
* ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name
This resolves a problem introduced by a0f7e7496d
("ARM: shmobile: sh73a0: add CMT1 clock support for DT")
which was included in v3.17-rc1.
This fix does not have any run-time affect at this time as the clock in
question is used by a SCIF device that is not enabled by default.
* tag 'renesas-clock-fixes-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fixes suspend/resume issue on imx53-qsrb due to PMIC IRQ pin
configuration missing
- A couple small SolidRun board fixes/correction from Rabeeh
and Russell
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT/XBJAAoJEFBXWFqHsHzOuqgH/3XqY4n0kL7lZQGRl8sBA/1m
bLtlKYaGjtn5ITXYONuWyxk9MrkCUaVUEEkcM3Gty6kHbCZ9F8nqSa5NiYs4MyGR
FiBX1GANmz96t61i90jlNNxHdPfnmgj3ZXEDTEj9g2brwGceUgQZv4/D59qSy41H
VlyIIOREQbrIoFlln1cEaKf2UXOpmSpB835QHROwy9K4aK0kZKAR4v5eqM2aQaIl
9VpvR5Xfsmr5vH/srlkY+Vc2ODVF1nQZsa3ikleAh2rzFQ4thwSKqpSxF7HL6EAo
zafJuI67ctyzIFk1PlsUuqCM2NimzACnpgrNG6Vn2KDq/JavNIsuyna0KgzzXqE=
=jOFz
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.17, 2nd take" from Shawn Guo:
i.MX fixes for 3.17, 2nd take:
- Fixes suspend/resume issue on imx53-qsrb due to PMIC IRQ pin
configuration missing
- A couple small SolidRun board fixes/correction from Rabeeh
and Russell
* tag 'imx-fixes-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: microsom-ar8035: MDIO pad must be set open drain
ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
ARM: dts: imx53-qsrb: Fix suspend/resume
Signed-off-by: Olof Johansson <olof@lixom.net>
by default as that's what many boards expect. Also fixes for omap5
clocks, PM wake-up events, GPIO interrupt cells for dra7, and few
other minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i+aY
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.17/fixes-against-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.17-rc2" from Tony Lindgren:
Fixes for omaps, mostly to revert NAND back to using software ECC
by default as that's what many boards expect. Also fixes for omap5
clocks, PM wake-up events, GPIO interrupt cells for dra7, and few
other minor fixes.
* tag 'omap-for-v3.17/fixes-against-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
ARM: dts: Enable UART wake-up events for beagleboard
ARM: dts: Remove twl6030 clk32g "regulator"
ARM: OMAP2+: omap_device: remove warning that clk alias already exists
ARM: OMAP: fix %d confusingly prefixed with 0x in format string
ARM: dts: DRA7: fix interrupt-cells for GPIO
mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
mtd: nand: omap: Revert to using software ECC by default
This patch frees the 'optinsn' slot when we get a range check error,
to prevent memory leaks.
Before this patch, cache entry in kprobe_insn_cache() won't be freed
if kprobe optimizing fails due to range check failure.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Pei Feiyue <peifeiyue@huawei.com>
Link: http://lkml.kernel.org/r/1406550019-70935-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit af040ffc9b ("ARM: make it easier to check the CPU part number
correctly") changed ARM_CPU_PART_X masks, and the way they are returned and
checked against. Usage of read_cpuid_part_number() is now deprecated, and
calling places updated accordingly. This actually broke cpuidle-big_little
initialization, as bl_idle_driver_init() performs a check using an hardcoded
mask on cpu_id.
Create an interface to perform the check (that is now even easier to read).
Define also a proper mask (ARM_CPU_PART_MASK) that makes this kind of checks
cleaner and helps preventing bugs in the future. Update usage accordingly.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On revisions of Cortex-A15 prior to r3p3, a CLREX instruction at PL1 may
falsely trigger a watchpoint exception, leading to potential data aborts
during exception return and/or livelock.
This patch resolves the issue in the following ways:
- Replacing our uses of CLREX with a dummy STREX sequence instead (as
we did for v6 CPUs).
- Removing the clrex code from v7_exit_coherency_flush and derivatives,
since this only exists as a minor performance improvement when
non-cached exclusives are in use (Linux doesn't use these).
Benchmarking on a variety of ARM cores revealed no measurable
performance difference with this change applied, so the change is
performed unconditionally and no new Kconfig entry is added.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARMv6 and ARMv7 early abort handlers clear the exclusive monitors
upon entry to the kernel, but this is redundant:
- We clear the monitors on every exception return since commit
200b812d00 ("Clear the exclusive monitor when returning from an
exception"), so this is not necessary to ensure the monitors are
cleared before returning from a fault handler.
- Any dummy STREX will target a temporary scratch area in memory, and
may succeed or fail without corrupting useful data. Its status value
will not be used.
- Any other STREX in the kernel must be preceded by an LDREX, which
will initialise the monitors consistently and will not depend on the
earlier state of the monitors.
Therefore we have no reason to care about the initial state of the
exclusive monitors when a data abort is taken, and clearing the monitors
prior to exception return (as we already do) is sufficient.
This patch removes the redundant clearing of the exclusive monitors from
the early abort handlers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kernel module build with GCOV profiling fails to load with the
following error:
$ insmod test_module.ko
test_module: unknown relocation: 38
insmod: can't insert 'test_module.ko': invalid module format
This happens because constructor pointers in the .init_array section
have not supported R_ARM_TARGET1 relocation type.
Documentation (ELF for the ARM Architecture) says:
"The relocation must be processed either in the same way as R_ARM_REL32 or
as R_ARM_ABS32: a virtual platform must specify which method is used."
Since kernel expects to see absolute addresses in .init_array R_ARM_TARGET1
relocation type should be treated the same way as R_ARM_ABS32.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We allocate "len" number of chars so we should put the NUL at "len - 1"
to avoid corrupting memory. Btw, strlen_user() is different from the
normal strlen() function because it includes NUL terminator in the
count.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Helge Deller <deller@gmx.de>
The correct position is topology.h, and this fix macros redefinition
problems for Netlogic.
[ralf@linux-mips.org: Fix build - the original patch broke most
configurations.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Jayachandran C. <jchandra@broadcom.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7575/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 15a3c7cc91 "x86, irq: Introduce two helper functions
to support irqdomain map operation" breaks LPSS ACPI enumerated
devices.
On startup, IOAPIC driver preallocates IRQ descriptors and programs
IOAPIC pins with default level and polarity attributes for all legacy
IRQs. Later legacy IRQ users may fail to set IOAPIC pin attributes
if the requested attributes conflicts with the default IOAPIC pin
attributes. So change mp_irqdomain_map() to allow the first legacy IRQ
user to reprogram IOAPIC pin with different attributes.
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1409118795-17046-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch is important for the MicroSOM implementation due to the
following details -
1. VIH of the Atheros phy is 1.7V.
2. NVCC_ENET which is the power domain of the MDIO pad is driven by the
PHY's LDO (i.e. either 1.8v or 2.5v).
3. The MicroSOM implements an onbouard 1.6kohm pull up to 3.3v (R3000).
In the case the PHY's LDO was 1.8v then there would be only a 100mV
margin for the signal to be acknowledged as high (1.8v-1.7v).
Due to that setting the pad as an open drain will let the 1.6kohm pull
that signal high to 3.3 that assures enough margins to the PHY to be
acked as '1' logic.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Pull s390 updates from Martin Schwidefsky:
- wire up the system calls seccomp, getrandom and memfd_create
- use static system information as input to add_device_randomness
- .. and three bug fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/sclp: remove unnecessary XTABS flag
s390/3215: fix tty output containing tabs
s390: wire up memfd_create syscall
s390: add system information as device randomness
s390/kdump: Clear subchannel ID to signal non-CCW/SCSI IPL
s390: wire up seccomp and getrandom syscalls
Similarly to DRA7, OMAP5 has l3 and l4 clock rates incorrectly calculated.
Fixed by using proper divider clock types for the clock nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove an unused local variable from head.S. It seems this was never
used even from the initial commit
9703d9d7f7 (arm64: Kernel booting and
initialisation), and is a left over from a previous implementation
of __calc_phys_offset.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Originally found by cppcheck:
[arch/arm64/crypto/sha2-ce-glue.c:153]: (warning) Assignment of
function parameter has no effect outside the function. Did you
forget dereferencing it?
Updating data by blocks * SHA256_BLOCK_SIZE at the end of
sha2_finup is redundant code and can be removed.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The edma_setup_from_hw() should know about the CC number when parsing the
CCCFG register - when it reads the register to be precise. The base
addresses for CCs stored in an array and we need to provide the correct id
to edma_read() in order to read the correct register.
Cc: <stable@vger.kernel.org> # 3.16
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There were several issues (of varying degree of importance) pointed out
with this code late in the review cycle, yet the code was still merged.
Let's rip it out for now and look at resubmitting at a later time.
This reverts most of commit 4fbe66d990.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Compiling mm/highmem.c gives a warning: passing argument 1 of
'virt_to_phys' makes pointer from integer without a cast
Fixed by casting to void*
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Don't pass things to macros that couldn't be dereferences if that
macro was actually a function.
- Don't use empty function-like macros.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CMP is an SMP implementation, and as a result of which, it needs
to select the SYS_SUPPORTS_SMP and SMP symbols. This fixes the
following build problem when CMP is enabled but SMP is not.
In file included from arch/mips/kernel/smp-cmp.c:34:0:
./arch/mips/include/asm/smp.h:26:0: error: "raw_smp_processor_id" redefined
[-Werror]
#define raw_smp_processor_id() (current_thread_info()->cpu)
[...]
In file included from arch/mips/kernel/smp-cmp.c:34:0:
./arch/mips/include/asm/smp.h:59:20: error: redefinition of
'smp_send_reschedule'
[...]
./arch/mips/include/asm/smp.h: In function 'smp_send_reschedule':
./arch/mips/include/asm/smp.h:63:8: error: dereferencing pointer to incomplete
type
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7436/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit dc4d7b37 (MIPS: ZBOOT: gather string functions into string.c)
moved the string related functions into a separate file, which might
cause the following build error, depending on the configuration:
| CC arch/mips/boot/compressed/decompress.o
| In file included from linux/arch/mips/boot/compressed/../../../../lib/decompress_unxz.c:234:0,
| from linux/arch/mips/boot/compressed/decompress.c:67:
| linux/arch/mips/boot/compressed/../../../../lib/xz/xz_dec_stream.c: In function 'fill_temp':
| linux/arch/mips/boot/compressed/../../../../lib/xz/xz_dec_stream.c:162:2: error: implicit declaration of function 'memcpy' [-Werror=implicit-function-declaration]
| cc1: some warnings being treated as errors
| linux/scripts/Makefile.build:308: recipe for target 'arch/mips/boot/compressed/decompress.o' failed
| make[6]: *** [arch/mips/boot/compressed/decompress.o] Error 1
| linux/arch/mips/Makefile:308: recipe for target 'vmlinuz' failed
It does not fail with the standard configuration, as when
CONFIG_DYNAMIC_DEBUG is not enabled <linux/string.h> gets included in
include/linux/dynamic_debug.h. There might be other ways for it to
get indirectly included.
We can't add the include directly in xz_dec_stream.c as some
architectures might want to use a different version for the boot/
directory (see for example arch/x86/boot/string.h).
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7420/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Broken values for UNCAC_BASE/IO_BASE caused complete breakage of IP28
builds. Only set special PHY_OFFSET and take everything else from
generic spaces.h
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7549/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit 81832d7e7962a40d08d9fe2e7e71b7887bc30097)
get_system_type() is not thread-safe on OCTEON. It uses static data,
also more dangerous issue is that it's calling cvmx_fuse_read_byte()
every time without any synchronization. Currently it's possible to get
processes stuck looping forever in kernel simply by launching multiple
readers of /proc/cpuinfo:
(while true; do cat /proc/cpuinfo > /dev/null; done) &
(while true; do cat /proc/cpuinfo > /dev/null; done) &
...
Fix by initializing the system type string only once during the early
boot.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Cc: stable@vger.kernel.org
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/7437/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
The CPS code is doing several memory loads when configuring the VPEs
from secondary cores, so the segmentation control registers must be
initialized in time otherwise the kernel will crash with strange
TLB exceptions.
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/7424/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Rename 'eva_entry' to 'platform_eva_init' as required by the new
'eva_init' macro in the eva.h header. Since this macro is now used
in a platform dependent way, it must not depend on its caller so move
the t1 register initialization inside this macro. Also set the .reorder
assembler option in case the caller may have previously set .noreorder.
This may allow a few assembler optimizations. Finally include missing
headers and document the register usage for this macro.
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/7423/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Generic code may need to perform certain operations when EVA is
enabled, for example, configure the segmentation registers during
boot. In order to avoid using more CONFIG_EVA ifdefs in the arch code,
such functions will be added in this header instead.
Initially this header contains a macro which will be used by generic
code later on during VPEs configuration on secondary cores.
All it does is to call the platform specific EVA init code in case
EVA is enabled.
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/7422/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Commit 4c21b8fd8f (MIPS: seccomp: Handle indirect system calls (o32))
added indirect syscall detection for O32 processes running on MIPS64
but it did not work as expected. The reason is the the scall64-o32
implementation differs compared to scall32-o32. In the former, the v0
(syscall number) register contains the absolute syscall number
(4000 + X) whereas in the latter it contains the relative syscall
number (X). Fix the code to avoid doing an extra addition, and load
the v0 register directly to the first argument for syscall_trace_enter.
Moreover, set the .reorder assembler option in order to have better
control on this part of the assembly code.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/7481/
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: James Hogan <james.hogan@imgtec.com>
On MIPS64, O32 processes set both TIF_32BIT_ADDR and
TIF_32BIT_REGS so the previous condition treated O32 applications
as N32 when evaluating seccomp filters. Fix the condition to check
both TIF_32BIT_{REGS, ADDR} for the N32 AUDIT flag.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/7480/
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: James Hogan <james.hogan@imgtec.com>
In preemptible kernel, only TIF_USEDFPU flag is reliable to distinguish
whether _init_fpu()/_restore_fp() is needed. Because the value of the
CP0_Status.CU1 isn't changed during preemption.
V2: Fix coding style.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/7515/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The nlm_xlp_defconfig build fails with
./arch/mips/include/asm/mach-netlogic/topology.h:15:0:
error: "topology_core_id" redefined [-Werror]
In file included from include/linux/smp.h:59:0,
[ ...]
from arch/mips/mm/dma-default.c:12:
./arch/mips/include/asm/smp.h:41:0:
note: this is the location of the previous definition
and similar errors.
This is caused by commit bda4584cd9 ("MIPS: Support CPU topology files
in sysfs") which adds the defines to arch/mips/include/asm/smp.h.
Remove the defines from arch/mips/include/asm/mach-netlogic/topology.h
as no longer necessary.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7513/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Multicore MIPSes without I/D hardware coherency suffered from a race
condition in the page fault handler. The page table entry was
published before any pending lazy D-cache flush was committed, hence
it allowed execution of stale page cache data by other VPEs in the
system.
To make the cache handling safe we need to perform flushing already in
the set_pte_at function. MIPSes without coherent I-caches can get a
small increase in flushes due to the unavailability of the execute
flag in set_pte_at.
[ralf@linux-mips.org: outlining set_pte_at() saves a good k in a test
build, so I moved its definition from pgtable.h to cache.c.]
Signed-off-by: Lars Persson <larper@axis.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7511/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Using kstrtol to parse the "{e,}memsize" variables was wrong because this
parses signed long numbers. In case of '{e,}memsize' >= 2G, the top bit
is set, resulting to -ERANGE errors and possibly random system memory
boundaries. We fix this by replacing "kstrtol" with "kstrtoul".
We also improve the code to check the kstrtoul return value and
print a warning if an error was returned.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7543/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
The previous commit was 316cad5c1d [MIPS:
BCM47XX: make reboot more relaiable]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: jogo@openwrt.org
Cc: zajec5@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7545/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add common declaration to get rid of following sparse warning: "symbol
'plat_irq_dispatch' was not declared. Should it be static?"
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7539/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove unused argument to make the plat_irq_dispatch() function
declaration similar to the realization of other platforms.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7538/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
