With the introduction of a dynamic ZONE_DMA range based on DT or IORT
information, there's no need for CMA allocations from the wider
ZONE_DMA32 since on most platforms ZONE_DMA will cover the 32-bit
addressable range. Remove the arm64_dma32_phys_limit and set
arm64_dma_phys_limit to cover the smallest DMA range required on the
platform. CMA allocation and crashkernel reservation now go in the
dynamically sized ZONE_DMA, allowing correct functionality on RPi4.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> # On RPi4B
Commit 49b3cf035e ("kasan: arm64: set TCR_EL1.TBID1 when enabled") set
the TBID1 bit for the KASAN_SW_TAGS configuration, freeing up 8 bits to
be used by PAC. With in-kernel MTE now in mainline, also set this bit
for the KASAN_HW_TAGS configuration.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Peter Collingbourne <pcc@google.com>
Acked-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Systems configured with CONFIG_ZONE_DMA32, CONFIG_ZONE_NORMAL and
!CONFIG_ZONE_DMA will fail to properly setup ARCH_LOW_ADDRESS_LIMIT. The
limit will default to ~0ULL, effectively spanning the whole memory,
which is too high for a configuration that expects low memory to be
capped at 4GB.
Fix ARCH_LOW_ADDRESS_LIMIT by falling back to arm64_dma32_phys_limit
when arm64_dma_phys_limit isn't set. arm64_dma32_phys_limit will honour
CONFIG_ZONE_DMA32, or span the entire memory when not enabled.
Fixes: 1a8e1cef76 ("arm64: use both ZONE_DMA and ZONE_DMA32")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20201218163307.10150-1-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add error reporting for hardware tag-based KASAN. When
CONFIG_KASAN_HW_TAGS is enabled, print KASAN report from the arm64 tag
fault handler.
SAS bits aren't set in ESR for all faults reported in EL1, so it's
impossible to find out the size of the access the caused the fault. Adapt
KASAN reporting code to handle this case.
Link: https://lkml.kernel.org/r/b559c82b6a969afedf53b4694b475f0234067a1a.1606161801.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Co-developed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Branislav Rankov <Branislav.Rankov@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Marco Elver <elver@google.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hardware tag-based KASAN relies on Memory Tagging Extension (MTE) feature
and requires it to be enabled. MTE supports
This patch adds a new mte_enable_kernel() helper, that enables MTE in
Synchronous mode in EL1 and is intended to be called from KASAN runtime
during initialization.
The Tag Checking operation causes a synchronous data abort as a
consequence of a tag check fault when MTE is configured in synchronous
mode.
As part of this change enable match-all tag for EL1 to allow the kernel to
access user pages without faulting. This is required because the kernel
does not have knowledge of the tags set by the user in a page.
Note: For MTE, the TCF bit field in SCTLR_EL1 affects only EL1 in a
similar way as TCF0 affects EL0.
MTE that is built on top of the Top Byte Ignore (TBI) feature hence we
enable it as part of this patch as well.
Link: https://lkml.kernel.org/r/7352b0a0899af65c2785416c8ca6bf3845b66fa1.1606161801.git.andreyknvl@google.com
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Co-developed-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Branislav Rankov <Branislav.Rankov@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Marco Elver <elver@google.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the implementation of the in-kernel fault handler.
When a tag fault happens on a kernel address:
* MTE is disabled on the current CPU,
* the execution continues.
When a tag fault happens on a user address:
* the kernel executes do_bad_area() and panics.
The tag fault handler for kernel addresses is currently empty and will be
filled in by a future commit.
Link: https://lkml.kernel.org/r/20201203102628.GB2224@gaia
Link: https://lkml.kernel.org/r/ad31529b073e22840b7a2246172c2b67747ed7c4.1606161801.git.andreyknvl@google.com
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Co-developed-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Branislav Rankov <Branislav.Rankov@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Marco Elver <elver@google.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will.deacon@arm.com>
[catalin.marinas@arm.com: ensure CONFIG_ARM64_PAN is enabled with MTE]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hardware tag-based KASAN for compatibility with the other modes stores
the tag associated to a page in page->flags. Due to this the kernel
faults on access when it allocates a page with an initial tag and the user
changes the tags.
Reset the tag associated by the kernel to a page in all the meaningful
places to prevent kernel faults on access.
Note: An alternative to this approach could be to modify page_to_virt().
This though could end up being racy, in fact if a CPU checks the
PG_mte_tagged bit and decides that the page is not tagged but another CPU
maps the same with PROT_MTE and becomes tagged the subsequent kernel
access would fail.
Link: https://lkml.kernel.org/r/9073d4e973747a6f78d5bdd7ebe17f290d087096.1606161801.git.andreyknvl@google.com
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Branislav Rankov <Branislav.Rankov@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Marco Elver <elver@google.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Software tag-based KASAN mode is fully initialized with kasan_init_tags(),
while the generic mode only requires kasan_init(). Move the
initialization message for tag-based mode into kasan_init_tags().
Also fix pr_fmt() usage for KASAN code: generic.c doesn't need it as it
doesn't use any printing functions; tag-based mode should use "kasan:"
instead of KBUILD_MODNAME (which stands for file name).
Link: https://lkml.kernel.org/r/29a30ea4e1750450dd1f693d25b7b6cb05913ecf.1606161801.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Branislav Rankov <Branislav.Rankov@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Marco Elver <elver@google.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a preparatory commit for the upcoming addition of a new hardware
tag-based (MTE-based) KASAN mode.
Hardware tag-based KASAN won't use kasan_depth. Only define and use it
when one of the software KASAN modes are enabled.
No functional changes for software modes.
Link: https://lkml.kernel.org/r/e16f15aeda90bc7fb4dfc2e243a14b74cc5c8219.1606161801.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Branislav Rankov <Branislav.Rankov@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Marco Elver <elver@google.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a preparatory commit for the upcoming addition of a new hardware
tag-based (MTE-based) KASAN mode.
Hardware tag-based KASAN won't be using shadow memory. Only initialize it
when one of the software KASAN modes are enabled.
No functional changes for software modes.
Link: https://lkml.kernel.org/r/d1742eea2cd728d150d49b144e49b6433405c7ba.1606161801.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Branislav Rankov <Branislav.Rankov@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Marco Elver <elver@google.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Work around broken GCC 4.9 handling of "S" asm constraint.
- Suppress W=1 missing prototype warnings.
- Warn the user when a small VA_BITS value cannot map the available
memory.
- Drop the useless update to per-cpu cycles.
-----BEGIN PGP SIGNATURE-----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=DKWC
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
"These are some some trivial updates that mostly fix/clean-up code
pushed during the merging window:
- Work around broken GCC 4.9 handling of "S" asm constraint
- Suppress W=1 missing prototype warnings
- Warn the user when a small VA_BITS value cannot map the available
memory
- Drop the useless update to per-cpu cycles"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Work around broken GCC 4.9 handling of "S" constraint
arm64: Warn the user when a small VA_BITS value wastes memory
arm64: entry: suppress W=1 prototype warnings
arm64: topology: Drop the useless update to per-cpu cycles
We have a handful of new kernel features for 5.11:
* Support for the contiguous memory allocator.
* Support for IRQ Time Accounting
* Support for stack tracing
* Support for strict /dev/mem
* Support for kernel section protection
I'm being a bit conservative on the cutoff for this round due to the
timing, so this is all the new development I'm going to take for this
cycle (even if some of it probably normally would have been OK). There
are, however, some fixes on the list that I will likely be sending along
either later this week or early next week.
There is one issue in here: one of my test configurations
(PREEMPT{,_DEBUG}=y) fails to boot on QEMU 5.0.0 (from April) as of the
.text.init alignment patch. With any luck we'll sort out the issue, but
given how many bugs get fixed all over the place and how unrelated those
features seem my guess is that we're just running into something that's
been lurking for a while and has already been fixed in the newer QEMU
(though I wouldn't be surprised if it's one of these implicit
assumptions we have in the boot flow). If it was hardware I'd be
strongly inclined to look more closely, but given that users can upgrade
their simulators I'm less worried about it.
There are two merge conflicts, both in build files. They're both a bit
clunky: arch/riscv/Kconfig is out of order (I have a script that's
supposed to keep them in order, I'll fix it) and lib/Makefile is out of
order (though GENERIC_LIB here doesn't mean quite what it does above).
-----BEGIN PGP SIGNATURE-----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=GWIH
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.11-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
"We have a handful of new kernel features for 5.11:
- Support for the contiguous memory allocator.
- Support for IRQ Time Accounting
- Support for stack tracing
- Support for strict /dev/mem
- Support for kernel section protection
I'm being a bit conservative on the cutoff for this round due to the
timing, so this is all the new development I'm going to take for this
cycle (even if some of it probably normally would have been OK). There
are, however, some fixes on the list that I will likely be sending
along either later this week or early next week.
There is one issue in here: one of my test configurations
(PREEMPT{,_DEBUG}=y) fails to boot on QEMU 5.0.0 (from April) as of
the .text.init alignment patch.
With any luck we'll sort out the issue, but given how many bugs get
fixed all over the place and how unrelated those features seem my
guess is that we're just running into something that's been lurking
for a while and has already been fixed in the newer QEMU (though I
wouldn't be surprised if it's one of these implicit assumptions we
have in the boot flow). If it was hardware I'd be strongly inclined to
look more closely, but given that users can upgrade their simulators
I'm less worried about it"
* tag 'riscv-for-linus-5.11-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
arm64: Use the generic devmem_is_allowed()
arm: Use the generic devmem_is_allowed()
RISC-V: Use the new generic devmem_is_allowed()
lib: Add a generic version of devmem_is_allowed()
riscv: Fixed kernel test robot warning
riscv: kernel: Drop unused clean rule
riscv: provide memmove implementation
RISC-V: Move dynamic relocation section under __init
RISC-V: Protect all kernel sections including init early
RISC-V: Align the .init.text section
RISC-V: Initialize SBI early
riscv: Enable ARCH_STACKWALK
riscv: Make stack walk callback consistent with generic code
riscv: Cleanup stacktrace
riscv: Add HAVE_IRQ_TIME_ACCOUNTING
riscv: Enable CMA support
riscv: Ignore Image.* and loader.bin
riscv: Clean up boot dir
riscv: Fix compressed Image formats build
RISC-V: Add kernel image sections to the resource tree
Merge misc updates from Andrew Morton:
- a few random little subsystems
- almost all of the MM patches which are staged ahead of linux-next
material. I'll trickle to post-linux-next work in as the dependents
get merged up.
Subsystems affected by this patch series: kthread, kbuild, ide, ntfs,
ocfs2, arch, and mm (slab-generic, slab, slub, dax, debug, pagecache,
gup, swap, shmem, memcg, pagemap, mremap, hmm, vmalloc, documentation,
kasan, pagealloc, memory-failure, hugetlb, vmscan, z3fold, compaction,
oom-kill, migration, cma, page-poison, userfaultfd, zswap, zsmalloc,
uaccess, zram, and cleanups).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (200 commits)
mm: cleanup kstrto*() usage
mm: fix fall-through warnings for Clang
mm: slub: convert sysfs sprintf family to sysfs_emit/sysfs_emit_at
mm: shmem: convert shmem_enabled_show to use sysfs_emit_at
mm:backing-dev: use sysfs_emit in macro defining functions
mm: huge_memory: convert remaining use of sprintf to sysfs_emit and neatening
mm: use sysfs_emit for struct kobject * uses
mm: fix kernel-doc markups
zram: break the strict dependency from lzo
zram: add stat to gather incompressible pages since zram set up
zram: support page writeback
mm/process_vm_access: remove redundant initialization of iov_r
mm/zsmalloc.c: rework the list_add code in insert_zspage()
mm/zswap: move to use crypto_acomp API for hardware acceleration
mm/zswap: fix passing zero to 'PTR_ERR' warning
mm/zswap: make struct kernel_param_ops definitions const
userfaultfd/selftests: hint the test runner on required privilege
userfaultfd/selftests: fix retval check for userfaultfd_open()
userfaultfd/selftests: always dump something in modes
userfaultfd: selftests: make __{s,u}64 format specifiers portable
...
For architectures that enable ARCH_HAS_SET_MEMORY having the ability to
verify that a page is mapped in the kernel direct map can be useful
regardless of hibernation.
Add RISC-V implementation of kernel_page_present(), update its forward
declarations and stubs to be a part of set_memory API and remove ugly
ifdefery in inlcude/linux/mm.h around current declarations of
kernel_page_present().
Link: https://lkml.kernel.org/r/20201109192128.960-5-rppt@kernel.org
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Edgecombe, Rick P" <rick.p.edgecombe@intel.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The design of DEBUG_PAGEALLOC presumes that __kernel_map_pages() must
never fail. With this assumption is wouldn't be safe to allow general
usage of this function.
Moreover, some architectures that implement __kernel_map_pages() have this
function guarded by #ifdef DEBUG_PAGEALLOC and some refuse to map/unmap
pages when page allocation debugging is disabled at runtime.
As all the users of __kernel_map_pages() were converted to use
debug_pagealloc_map_pages() it is safe to make it available only when
DEBUG_PAGEALLOC is set.
Link: https://lkml.kernel.org/r/20201109192128.960-4-rppt@kernel.org
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Edgecombe, Rick P" <rick.p.edgecombe@intel.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ARM and ARM64 free unused parts of the memory map just before the
initialization of the page allocator. To allow holes in the memory map both
architectures overload pfn_valid() and define HAVE_ARCH_PFN_VALID.
Allowing holes in the memory map for FLATMEM may be useful for small
machines, such as ARC and m68k and will enable those architectures to cease
using DISCONTIGMEM and still support more than one memory bank.
Move the functions that free unused memory map to generic mm and enable
them in case HAVE_ARCH_PFN_VALID=y.
Link: https://lkml.kernel.org/r/20201101170454.9567-10-rppt@kernel.org
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Meelis Roos <mroos@linux.ee>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The memblock code ignores any memory that doesn't fit in the
linear mapping. In order to preserve the distance between two physical
memory locations and their mappings in the linear map, any hole between
two memory regions occupies the same space in the linear map.
On most systems, this is hardly a problem (the memory banks are close
together, and VA_BITS represents a large space compared to the available
memory *and* the potential gaps).
On NUMA systems, things are quite different: the gaps between the
memory nodes can be pretty large compared to the memory size itself,
and the range from memblock_start_of_DRAM() to memblock_end_of_DRAM()
can exceed the space described by VA_BITS.
Unfortunately, we're not very good at making this obvious to the user,
and on a D05 system (two sockets and 4 nodes with 64GB each)
accidentally configured with 39bit VA, we display something like this:
[ 0.000000] NUMA: NODE_DATA [mem 0x1ffbffe100-0x1ffbffffff]
[ 0.000000] NUMA: NODE_DATA [mem 0x2febfc1100-0x2febfc2fff]
[ 0.000000] NUMA: Initmem setup node 2 [<memory-less node>]
[ 0.000000] NUMA: NODE_DATA [mem 0x2febfbf200-0x2febfc10ff]
[ 0.000000] NUMA: NODE_DATA(2) on node 1
[ 0.000000] NUMA: Initmem setup node 3 [<memory-less node>]
[ 0.000000] NUMA: NODE_DATA [mem 0x2febfbd300-0x2febfbf1ff]
[ 0.000000] NUMA: NODE_DATA(3) on node 1
which isn't very explicit, and doesn't tell the user why 128GB
have suddently disappeared.
Let's add a warning message telling the user that memory has been
truncated, and offer a potential solution (bumping VA_BITS up).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20201215152918.1511108-1-maz@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As part of adding STRICT_DEVMEM support to the RISC-V port, Zong provided an
implementation of devmem_is_allowed() that's exactly the same as the version in
a handful of other ports. Rather than duplicate code, I've put a generic
version of this in lib/ and used it for the RISC-V port.
* palmer/generic-devmem:
arm64: Use the generic devmem_is_allowed()
arm: Use the generic devmem_is_allowed()
RISC-V: Use the new generic devmem_is_allowed()
lib: Add a generic version of devmem_is_allowed()
I recently copied this into lib/ for use by the RISC-V port.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
* for-next/kvm-build-fix:
: Fix KVM build issues with 64K pages
KVM: arm64: Fix build error in user_mem_abort()
* for-next/va-refactor:
: VA layout changes
arm64: mm: don't assume struct page is always 64 bytes
Documentation/arm64: fix RST layout of memory.rst
arm64: mm: tidy up top of kernel VA space
arm64: mm: make vmemmap region a projection of the linear region
arm64: mm: extend linear region for 52-bit VA configurations
* for-next/lto:
: Upgrade READ_ONCE() to RCpc acquire on arm64 with LTO
arm64: lto: Strengthen READ_ONCE() to acquire when CONFIG_LTO=y
arm64: alternatives: Remove READ_ONCE() usage during patch operation
arm64: cpufeatures: Add capability for LDAPR instruction
arm64: alternatives: Split up alternative.h
arm64: uaccess: move uao_* alternatives to asm-uaccess.h
* for-next/mem-hotplug:
: Memory hotplug improvements
arm64/mm/hotplug: Ensure early memory sections are all online
arm64/mm/hotplug: Enable MEM_OFFLINE event handling
arm64/mm/hotplug: Register boot memory hot remove notifier earlier
arm64: mm: account for hotplug memory when randomizing the linear region
* for-next/cppc-ffh:
: Add CPPC FFH support using arm64 AMU counters
arm64: abort counter_read_on_cpu() when irqs_disabled()
arm64: implement CPPC FFH support using AMUs
arm64: split counter validation function
arm64: wrap and generalise counter read functions
* for-next/pad-image-header:
: Pad Image header to 64KB and unmap it
arm64: head: tidy up the Image header definition
arm64/head: avoid symbol names pointing into first 64 KB of kernel image
arm64: omit [_text, _stext) from permanent kernel mapping
* for-next/zone-dma-default-32-bit:
: Default to 32-bit wide ZONE_DMA (previously reduced to 1GB for RPi4)
of: unittest: Fix build on architectures without CONFIG_OF_ADDRESS
mm: Remove examples from enum zone_type comment
arm64: mm: Set ZONE_DMA size based on early IORT scan
arm64: mm: Set ZONE_DMA size based on devicetree's dma-ranges
of: unittest: Add test for of_dma_get_max_cpu_address()
of/address: Introduce of_dma_get_max_cpu_address()
arm64: mm: Move zone_dma_bits initialization into zone_sizes_init()
arm64: mm: Move reserve_crashkernel() into mem_init()
arm64: Force NO_BLOCK_MAPPINGS if crashkernel reservation is required
arm64: Ignore any DMA offsets in the max_zone_phys() calculation
* for-next/signal-tag-bits:
: Expose the FAR_EL1 tag bits in siginfo
arm64: expose FAR_EL1 tag bits in siginfo
signal: define the SA_EXPOSE_TAGBITS bit in sa_flags
signal: define the SA_UNSUPPORTED bit in sa_flags
arch: provide better documentation for the arch-specific SA_* flags
signal: clear non-uapi flag bits when passing/returning sa_flags
arch: move SA_* definitions to generic headers
parisc: start using signal-defs.h
parisc: Drop parisc special case for __sighandler_t
* for-next/cmdline-extended:
: Add support for CONFIG_CMDLINE_EXTENDED
arm64: Extend the kernel command line from the bootloader
arm64: kaslr: Refactor early init command line parsing
Now that the uaccess primitives dont take addr_limit into account, we
have no need to manipulate this via set_fs() and get_fs(). Remove
support for these, along with some infrastructure this renders
redundant.
We no longer need to flip UAO to access kernel memory under KERNEL_DS,
and head.S unconditionally clears UAO for all kernel configurations via
an ERET in init_kernel_el. Thus, we don't need to dynamically flip UAO,
nor do we need to context-switch it. However, we still need to adjust
PAN during SDEI entry.
Masking of __user pointers no longer needs to use the dynamic value of
addr_limit, and can use a constant derived from the maximum possible
userspace task size. A new TASK_SIZE_MAX constant is introduced for
this, which is also used by core code. In configurations supporting
52-bit VAs, this may include a region of unusable VA space above a
48-bit TTBR0 limit, but never includes any portion of TTBR1.
Note that TASK_SIZE_MAX is an exclusive limit, while USER_DS and
KERNEL_DS were inclusive limits, and is converted to a mask by
subtracting one.
As the SDEI entry code repurposes the otherwise unnecessary
pt_regs::orig_addr_limit field to store the TTBR1 of the interrupted
context, for now we rename that to pt_regs::sdei_ttbr1. In future we can
consider factoring that out.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201202131558.39270-10-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Let's make SCTLR_ELx initialization a bit clearer by using meaningful
names for the initialization values, following the same scheme for
SCTLR_EL1 and SCTLR_EL2.
These definitions will be used more widely in subsequent patches.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201113124937.20574-5-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In debug_exception_enter() and debug_exception_exit() we trace hardirqs
on/off while RCU isn't guaranteed to be watching, and we don't save and
restore the hardirq state, and so may return with this having changed.
Handle this appropriately with new entry/exit helpers which do the bare
minimum to ensure this is appropriately maintained, without marking
debug exceptions as NMIs. These are placed in entry-common.c with the
other entry/exit helpers.
In future we'll want to reconsider whether some debug exceptions should
be NMIs, but this will require a significant refactoring, and for now
this should prevent issues with lockdep and RCU.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marins <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201130115950.22492-12-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
When built with PROVE_LOCKING, NO_HZ_FULL, and CONTEXT_TRACKING_FORCE
will WARN() at boot time that interrupts are enabled when we call
context_tracking_user_enter(), despite the DAIF flags indicating that
IRQs are masked.
The problem is that we're not tracking IRQ flag changes accurately, and
so lockdep believes interrupts are enabled when they are not (and
vice-versa). We can shuffle things so to make this more accurate. For
kernel->user transitions there are a number of constraints we need to
consider:
1) When we call __context_tracking_user_enter() HW IRQs must be disabled
and lockdep must be up-to-date with this.
2) Userspace should be treated as having IRQs enabled from the PoV of
both lockdep and tracing.
3) As context_tracking_user_enter() stops RCU from watching, we cannot
use RCU after calling it.
4) IRQ flag tracing and lockdep have state that must be manipulated
before RCU is disabled.
... with similar constraints applying for user->kernel transitions, with
the ordering reversed.
The generic entry code has enter_from_user_mode() and
exit_to_user_mode() helpers to handle this. We can't use those directly,
so we add arm64 copies for now (without the instrumentation markers
which aren't used on arm64). These replace the existing user_exit() and
user_exit_irqoff() calls spread throughout handlers, and the exception
unmasking is left as-is.
Note that:
* The accounting for debug exceptions from userspace now happens in
el0_dbg() and ret_to_user(), so this is removed from
debug_exception_enter() and debug_exception_exit(). As
user_exit_irqoff() wakes RCU, the userspace-specific check is removed.
* The accounting for syscalls now happens in el0_svc(),
el0_svc_compat(), and ret_to_user(), so this is removed from
el0_svc_common(). This does not adversely affect the workaround for
erratum 1463225, as this does not depend on any of the state tracking.
* In ret_to_user() we mask interrupts with local_daif_mask(), and so we
need to inform lockdep and tracing. Here a trace_hardirqs_off() is
sufficient and safe as we have not yet exited kernel context and RCU
is usable.
* As PROVE_LOCKING selects TRACE_IRQFLAGS, the ifdeferry in entry.S only
needs to check for the latter.
* EL0 SError handling will be dealt with in a subsequent patch, as this
needs to be treated as an NMI.
Prior to this patch, booting an appropriately-configured kernel would
result in spats as below:
| DEBUG_LOCKS_WARN_ON(lockdep_hardirqs_enabled())
| WARNING: CPU: 2 PID: 1 at kernel/locking/lockdep.c:5280 check_flags.part.54+0x1dc/0x1f0
| Modules linked in:
| CPU: 2 PID: 1 Comm: init Not tainted 5.10.0-rc3 #3
| Hardware name: linux,dummy-virt (DT)
| pstate: 804003c5 (Nzcv DAIF +PAN -UAO -TCO BTYPE=--)
| pc : check_flags.part.54+0x1dc/0x1f0
| lr : check_flags.part.54+0x1dc/0x1f0
| sp : ffff80001003bd80
| x29: ffff80001003bd80 x28: ffff66ce801e0000
| x27: 00000000ffffffff x26: 00000000000003c0
| x25: 0000000000000000 x24: ffffc31842527258
| x23: ffffc31842491368 x22: ffffc3184282d000
| x21: 0000000000000000 x20: 0000000000000001
| x19: ffffc318432ce000 x18: 0080000000000000
| x17: 0000000000000000 x16: ffffc31840f18a78
| x15: 0000000000000001 x14: ffffc3184285c810
| x13: 0000000000000001 x12: 0000000000000000
| x11: ffffc318415857a0 x10: ffffc318406614c0
| x9 : ffffc318415857a0 x8 : ffffc31841f1d000
| x7 : 647261685f706564 x6 : ffffc3183ff7c66c
| x5 : ffff66ce801e0000 x4 : 0000000000000000
| x3 : ffffc3183fe00000 x2 : ffffc31841500000
| x1 : e956dc24146b3500 x0 : 0000000000000000
| Call trace:
| check_flags.part.54+0x1dc/0x1f0
| lock_is_held_type+0x10c/0x188
| rcu_read_lock_sched_held+0x70/0x98
| __context_tracking_enter+0x310/0x350
| context_tracking_enter.part.3+0x5c/0xc8
| context_tracking_user_enter+0x6c/0x80
| finish_ret_to_user+0x2c/0x13cr
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201130115950.22492-8-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
We recently introduced a 1 GB sized ZONE_DMA to cater for platforms
incorporating masters that can address less than 32 bits of DMA, in
particular the Raspberry Pi 4, which has 4 or 8 GB of DRAM, but has
peripherals that can only address up to 1 GB (and its PCIe host
bridge can only access the bottom 3 GB)
Instructing the DMA layer about these limitations is straight-forward,
even though we had to fix some issues regarding memory limits set in
the IORT for named components, and regarding the handling of ACPI _DMA
methods. However, the DMA layer also needs to be able to allocate
memory that is guaranteed to meet those DMA constraints, for bounce
buffering as well as allocating the backing for consistent mappings.
This is why the 1 GB ZONE_DMA was introduced recently. Unfortunately,
it turns out the having a 1 GB ZONE_DMA as well as a ZONE_DMA32 causes
problems with kdump, and potentially in other places where allocations
cannot cross zone boundaries. Therefore, we should avoid having two
separate DMA zones when possible.
So let's do an early scan of the IORT, and only create the ZONE_DMA
if we encounter any devices that need it. This puts the burden on
the firmware to describe such limitations in the IORT, which may be
redundant (and less precise) if _DMA methods are also being provided.
However, it should be noted that this situation is highly unusual for
arm64 ACPI machines. Also, the DMA subsystem still gives precedence to
the _DMA method if implemented, and so we will not lose the ability to
perform streaming DMA outside the ZONE_DMA if the _DMA method permits
it.
[nsaenz: unified implementation with DT's counterpart]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20201119175400.9995-7-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We recently introduced a 1 GB sized ZONE_DMA to cater for platforms
incorporating masters that can address less than 32 bits of DMA, in
particular the Raspberry Pi 4, which has 4 or 8 GB of DRAM, but has
peripherals that can only address up to 1 GB (and its PCIe host
bridge can only access the bottom 3 GB)
The DMA layer also needs to be able to allocate memory that is
guaranteed to meet those DMA constraints, for bounce buffering as well
as allocating the backing for consistent mappings. This is why the 1 GB
ZONE_DMA was introduced recently. Unfortunately, it turns out the having
a 1 GB ZONE_DMA as well as a ZONE_DMA32 causes problems with kdump, and
potentially in other places where allocations cannot cross zone
boundaries. Therefore, we should avoid having two separate DMA zones
when possible.
So, with the help of of_dma_get_max_cpu_address() get the topmost
physical address accessible to all DMA masters in system and use that
information to fine-tune ZONE_DMA's size. In the absence of addressing
limited masters ZONE_DMA will span the whole 32-bit address space,
otherwise, in the case of the Raspberry Pi 4 it'll only span the 30-bit
address space, and have ZONE_DMA32 cover the rest of the 32-bit address
space.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20201119175400.9995-6-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
zone_dma_bits's initialization happens earlier that it's actually
needed, in arm64_memblock_init(). So move it into the more suitable
zone_sizes_init().
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/r/20201119175400.9995-3-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
crashkernel might reserve memory located in ZONE_DMA. We plan to delay
ZONE_DMA's initialization after unflattening the devicetree and ACPI's
boot table initialization, so move it later in the boot process.
Specifically into bootmem_init() since request_standard_resources()
depends on it.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/r/20201119175400.9995-2-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
mem_init() currently relies on knowing the boundaries of the crashkernel
reservation to map such region with page granularity for later
unmapping via set_memory_valid(..., 0). If the crashkernel reservation
is deferred, such boundaries are not known when the linear mapping is
created. Simply parse the command line for "crashkernel" and, if found,
create the linear map with NO_BLOCK_MAPPINGS.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: James Morse <james.morse@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20201119175556.18681-1-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently, the kernel assumes that if RAM starts above 32-bit (or
zone_bits), there is still a ZONE_DMA/DMA32 at the bottom of the RAM and
such constrained devices have a hardwired DMA offset. In practice, we
haven't noticed any such hardware so let's assume that we can expand
ZONE_DMA32 to the available memory if no RAM below 4GB. Similarly,
ZONE_DMA is expanded to the 4GB limit if no RAM addressable by
zone_bits.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20201118185809.1078362-1-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When section mappings are enabled, we allocate vmemmap pages from
physically continuous memory of size PMD_SIZE using
vmemmap_alloc_block_buf(). Section mappings are good to reduce TLB
pressure. But when system is highly fragmented and memory blocks are
being hot-added at runtime, its possible that such physically continuous
memory allocations can fail. Rather than failing the memory hot-add
procedure, add a fallback option to allocate vmemmap pages from
discontinuous pages using vmemmap_populate_basepages().
Signed-off-by: Sudarshan Rajagopalan <sudaraja@codeaurora.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/d6c06f2ef39bbe6c715b2f6db76eb16155fdcee6.1602722808.git.sudaraja@codeaurora.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In a previous patch, we increased the size of the EFI PE/COFF header
to 64 KB, which resulted in the _stext symbol to appear at a fixed
offset of 64 KB into the image.
Since 64 KB is also the largest page size we support, this completely
removes the need to map the first 64 KB of the kernel image, given that
it only contains the arm64 Image header and the EFI header, neither of
which we ever access again after booting the kernel. More importantly,
we should avoid an executable mapping of non-executable and not entirely
predictable data, to deal with the unlikely event that we inadvertently
emitted something that looks like an opcode that could be used as a
gadget for speculative execution.
So let's limit the kernel mapping of .text to the [_stext, _etext)
region, which matches the view of generic code (such as kallsyms) when
it reasons about the boundaries of the kernel's .text section.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201117124729.12642-2-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
During memory hotplug process, the linear mapping should not be created for
a given memory range if that would fall outside the maximum allowed linear
range. Else it might cause memory corruption in the kernel virtual space.
Maximum linear mapping region is [PAGE_OFFSET..(PAGE_END -1)] accommodating
both its ends but excluding PAGE_END. Max physical range that can be mapped
inside this linear mapping range, must also be derived from its end points.
This ensures that arch_add_memory() validates memory hot add range for its
potential linear mapping requirements, before creating it with
__create_pgd_mapping().
Fixes: 4ab2150615 ("arm64: Add memory hotplug support")
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Steven Price <steven.price@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1605252614-761-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Commit 8c96400d6a simplified the page-to-virt and virt-to-page
conversions, based on the assumption that struct page is always 64
bytes in size, in which case we can use a single signed shift to
perform the conversion (provided that the vmemmap array is placed
appropriately in the kernel VA space)
Unfortunately, this assumption turns out not to hold, and so we need
to revert part of this commit, and go back to an affine transformation.
Given that all the quantities involved are compile time constants,
this should not make any practical difference.
Fixes: 8c96400d6a ("arm64: mm: make vmemmap region a projection of the linear region")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20201110180511.29083-1-ardb@kernel.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This adds a validation function that scans the entire boot memory and makes
sure that all early memory sections are online. This check is essential for
the memory notifier to work properly, as it cannot prevent any boot memory
from offlining, if all sections are not online to begin with. Although the
boot section scanning is selectively enabled with DEBUG_VM.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1604896137-16644-4-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This enables MEM_OFFLINE memory event handling. It will help intercept any
possible error condition such as if boot memory some how still got offlined
even after an explicit notifier failure, potentially by a future change in
generic hot plug framework. This would help detect such scenarios and help
debug further. While here, also call out the first section being attempted
for offline or got offlined.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1604896137-16644-3-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This moves memory notifier registration earlier in the boot process from
device_initcall() to early_initcall() which will help in guarding against
potential early boot memory offline requests. Even though there should not
be any actual offlinig requests till memory block devices are initialized
with memory_dev_init() but then generic init sequence might just change in
future. Hence an early registration for the memory event notifier would be
helpful. While here, just skip the registration if CONFIG_MEMORY_HOTREMOVE
is not enabled and also call out when memory notifier registration fails.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1604896137-16644-2-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As a hardening measure, we currently randomize the placement of
physical memory inside the linear region when KASLR is in effect.
Since the random offset at which to place the available physical
memory inside the linear region is chosen early at boot, it is
based on the memblock description of memory, which does not cover
hotplug memory. The consequence of this is that the randomization
offset may be chosen such that any hotplugged memory located above
memblock_end_of_DRAM() that appears later is pushed off the end of
the linear region, where it cannot be accessed.
So let's limit this randomization of the linear region to ensure
that this can no longer happen, by using the CPU's addressable PA
range instead. As it is guaranteed that no hotpluggable memory will
appear that falls outside of that range, we can safely put this PA
range sized window anywhere in the linear region.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Steven Price <steven.price@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20201014081857.3288-1-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Depending on configuration options and specific code paths, we either
use the empty_zero_page or the configuration-dependent reserved_ttbr0
as a reserved value for TTBR{0,1}_EL1.
To simplify this code, let's always allocate and use the same
reserved_pg_dir, replacing reserved_ttbr0. Note that this is allocated
(and hence pre-zeroed), and is also marked as read-only in the kernel
Image mapping.
Keeping this separate from the empty_zero_page potentially helps with
robustness as the empty_zero_page is used in a number of cases where a
failure to map it read-only could allow it to become corrupted.
The (presently unused) swapper_pg_end symbol is also removed, and
comments are added wherever we rely on the offsets between the
pre-allocated pg_dirs to keep these cases easily identifiable.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201103102229.8542-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that we have reverted the introduction of the vmemmap struct page
pointer and the separate physvirt_offset, we can simplify things further,
and place the vmemmap region in the VA space in such a way that virtual
to page translations and vice versa can be implemented using a single
arithmetic shift.
One happy coincidence resulting from this is that the 48-bit/4k and
52-bit/64k configurations (which are assumed to be the two most
prevalent) end up with the same placement of the vmemmap region. In
a subsequent patch, we will take advantage of this, and unify the
memory maps even more.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Link: https://lore.kernel.org/r/20201008153602.9467-4-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For historical reasons, the arm64 kernel VA space is configured as two
equally sized halves, i.e., on a 48-bit VA build, the VA space is split
into a 47-bit vmalloc region and a 47-bit linear region.
When support for 52-bit virtual addressing was added, this equal split
was kept, resulting in a substantial waste of virtual address space in
the linear region:
48-bit VA 52-bit VA
0xffff_ffff_ffff_ffff +-------------+ +-------------+
| vmalloc | | vmalloc |
0xffff_8000_0000_0000 +-------------+ _PAGE_END(48) +-------------+
| linear | : :
0xffff_0000_0000_0000 +-------------+ : :
: : : :
: : : :
: : : :
: : : currently :
: unusable : : :
: : : unused :
: by : : :
: : : :
: hardware : : :
: : : :
0xfff8_0000_0000_0000 : : _PAGE_END(52) +-------------+
: : | |
: : | |
: : | |
: : | |
: : | |
: unusable : | |
: : | linear |
: by : | |
: : | region |
: hardware : | |
: : | |
: : | |
: : | |
: : | |
: : | |
: : | |
0xfff0_0000_0000_0000 +-------------+ PAGE_OFFSET +-------------+
As illustrated above, the 52-bit VA kernel uses 47 bits for the vmalloc
space (as before), to ensure that a single 64k granule kernel image can
support any 64k granule capable system, regardless of whether it supports
the 52-bit virtual addressing extension. However, due to the fact that
the VA space is still split in equal halves, the linear region is only
2^51 bytes in size, wasting almost half of the 52-bit VA space.
Let's fix this, by abandoning the equal split, and simply assigning all
VA space outside of the vmalloc region to the linear region.
The KASAN shadow region is reconfigured so that it ends at the start of
the vmalloc region, and grows downwards. That way, the arrangement of
the vmalloc space (which contains kernel mappings, modules, BPF region,
the vmemmap array etc) is identical between non-KASAN and KASAN builds,
which aids debugging.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Link: https://lore.kernel.org/r/20201008153602.9467-3-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
On Cortex-A77 r0p0 and r1p0, a sequence of a non-cacheable or device load
and a store exclusive or PAR_EL1 read can cause a deadlock.
The workaround requires a DMB SY before and after a PAR_EL1 register
read. In addition, it's possible an interrupt (doing a device read) or
KVM guest exit could be taken between the DMB and PAR read, so we
also need a DMB before returning from interrupt and before returning to
a guest.
A deadlock is still possible with the workaround as KVM guests must also
have the workaround. IOW, a malicious guest can deadlock an affected
systems.
This workaround also depends on a firmware counterpart to enable the h/w
to insert DMB SY after load and store exclusive instructions. See the
errata document SDEN-1152370 v10 [1] for more information.
[1] https://static.docs.arm.com/101992/0010/Arm_Cortex_A77_MP074_Software_Developer_Errata_Notice_v10.pdf
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Cc: kvmarm@lists.cs.columbia.edu
Link: https://lore.kernel.org/r/20201028182839.166037-2-robh@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
