DROM for USB4 host/device has a shorter header than Thunderbolt DROM
header. This patch addresses host/device with USB4 DROM (According to spec:
Universal Serial Bus 4 (USB4) Device ROM Specification, Rev 1.0, Feb-2021).
While there correct the data_len field to be 12 bits and rename
__unknown1 to reserved following the spec.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 router DROM differs sligthly from Thunderbolt 1-3 DROM. For
instance it does not include UID and CRC8 in the header section, and it
has product descriptor genereric entry to describe the product IDs and
related information. If the "Version" field in the DROM header section
reads 3 it means the router only has USB4 DROM and if it reads 1 it
means the router supports TBT3 compatible DROM.
For this reason, update the DROM parsing code to support "pure" USB4
DROMs too.
While there drop the extra empty line at the end of tb_drom_read().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Fix kernel-doc descriptions of the two non-static functions. This also
gets rid of the rest of the warnings on W=1 build.
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Fixes the following W=1 kernel build warning(s):
drivers/thunderbolt/eeprom.c:19: warning: Function parameter or member 'sw' not described in 'tb_eeprom_ctl_write'
drivers/thunderbolt/eeprom.c:19: warning: Function parameter or member 'ctl' not described in 'tb_eeprom_ctl_write'
drivers/thunderbolt/eeprom.c:27: warning: Function parameter or member 'sw' not described in 'tb_eeprom_ctl_read'
drivers/thunderbolt/eeprom.c:27: warning: Function parameter or member 'ctl' not described in 'tb_eeprom_ctl_read'
drivers/thunderbolt/eeprom.c:27: warning: expecting prototype for tb_eeprom_ctl_write(). Prototype was for tb_eeprom_ctl_read() instead
drivers/thunderbolt/eeprom.c:43: warning: Function parameter or member 'sw' not described in 'tb_eeprom_active'
drivers/thunderbolt/eeprom.c:43: warning: Function parameter or member 'enable' not described in 'tb_eeprom_active'
drivers/thunderbolt/eeprom.c:73: warning: Function parameter or member 'sw' not described in 'tb_eeprom_transfer'
drivers/thunderbolt/eeprom.c:73: warning: Function parameter or member 'ctl' not described in 'tb_eeprom_transfer'
drivers/thunderbolt/eeprom.c:73: warning: Function parameter or member 'direction' not described in 'tb_eeprom_transfer'
drivers/thunderbolt/eeprom.c:97: warning: Function parameter or member 'sw' not described in 'tb_eeprom_out'
drivers/thunderbolt/eeprom.c:97: warning: Function parameter or member 'val' not described in 'tb_eeprom_out'
drivers/thunderbolt/eeprom.c:117: warning: Function parameter or member 'sw' not described in 'tb_eeprom_in'
drivers/thunderbolt/eeprom.c:117: warning: Function parameter or member 'val' not described in 'tb_eeprom_in'
drivers/thunderbolt/eeprom.c:138: warning: Function parameter or member 'sw' not described in 'tb_eeprom_get_drom_offset'
drivers/thunderbolt/eeprom.c:138: warning: Function parameter or member 'offset' not described in 'tb_eeprom_get_drom_offset'
drivers/thunderbolt/eeprom.c:170: warning: Function parameter or member 'sw' not described in 'tb_eeprom_read_n'
drivers/thunderbolt/eeprom.c:170: warning: Function parameter or member 'offset' not described in 'tb_eeprom_read_n'
drivers/thunderbolt/eeprom.c:170: warning: Function parameter or member 'val' not described in 'tb_eeprom_read_n'
drivers/thunderbolt/eeprom.c:170: warning: Function parameter or member 'count' not described in 'tb_eeprom_read_n'
drivers/thunderbolt/eeprom.c:383: warning: Function parameter or member 'sw' not described in 'tb_drom_parse_entries'
drivers/thunderbolt/eeprom.c:417: warning: Function parameter or member 'sw' not described in 'tb_drom_copy_efi'
drivers/thunderbolt/eeprom.c:417: warning: Function parameter or member 'size' not described in 'tb_drom_copy_efi'
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[ mw: Demote only static functions ]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Kai-Heng reported that sometimes DROM parsing of ASUS PA27AC Thunderbolt 3
monitor fails. This makes the driver to fail to add the device so only
DisplayPort tunneling is functional.
It is not clear what exactly happens but waiting for 100 ms and retrying
the read seems to work this around so we do that here.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206493
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Some external devices can support completing thunderbolt authentication
when they are unplugged. For this to work though, the link controller must
remain operational.
The only device known to support this right now is the Dell WD19TB, so add
a quirk for this.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 is the public specification based on Thunderbolt 3 protocol. There
are some differences in register layouts and flows. In addition to PCIe
and DP tunneling, USB4 supports tunneling of USB 3.x. USB4 is also
backward compatible with Thunderbolt 3 (and older generations but the
spec only talks about 3rd generation). USB4 compliant devices can be
identified by checking USB4 version field in router configuration space.
This patch adds initial support for USB4 compliant hosts and devices
which enables following features provided by the existing functionality
in the driver:
- PCIe tunneling
- Display Port tunneling
- Host and device NVM firmware upgrade
- P2P networking
This brings the USB4 support to the same level that we already have for
Thunderbolt 1, 2 and 3 devices.
Note the spec talks about host and device "routers" but in the driver we
still use term "switch" in most places. Both can be used interchangeably.
Co-developed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-5-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are going to re-use tb_drom_read() for USB4 DROM reading as well.
USB4 has separate router operations for this which does not need the
drom_offset. Therefore we move call to tb_eeprom_get_drom_offset() into
tb_eeprom_read_n() where it is needed.
While there change return -ENOSYS to -ENODEV because the former is only
supposed to be used with system calls (invalid syscall nr).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-3-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently read how sibling lane adapter ports relate each other from
DROM (Device ROM). If the two lane adapter ports go through the same
physical connector these lanes can then be bonded together. However,
some cases DROM does not provide this information or it is missing
completely (host routers typically do not have DROM). In this case we
have hard-coded the relationship.
Expand this to work with both legacy devices where lane adapter ports 1
and 2, and 3 and 4 are always linked together, and with USB4 devices
where lane adapter 1 is always following lane adapter 0 or is disabled
completely (see USB4 section 5.2.1 for more information).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There are two ways to mark a port as unimplemented. Typical way is to
return port type as TB_TYPE_INACTIVE when its config space is read.
Alternatively if the port is not physically present (such as ports 10
and 11 in ICL) reading from port config space returns
TB_CFG_ERROR_INVALID_CONFIG_SPACE instead. Currently the driver bails
out from adding the switch if it receives any error during port
inititialization which is wrong.
Handle this properly and just leave the port as TB_TYPE_INACTIVE before
continuing to the next port.
This also allows us to get rid of special casing for Light Ridge port 5
in eeprom.c.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Use device_property_count_uXX() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel has done pretty major changes to the driver and we continue to do
so in the future as well. Add Intel as copyright holder of the files we
have done changes.
While there drop "Cactus Ridge" from the headers because this driver
works also with other Thunderbolt controllers.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the driver logs quite a lot to the system message buffer even
when doing normal operations. This information is not useful for
ordinary users and might even annoy some.
For this reason convert most of the logs at info level to happen at
debug level instead. The nice output formatting is untouched.
Logging can be easily re-enabled by passing "thunderbolt.dyndbg" in the
kernel command line (or using the corresponding control file runtime).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in tb_sw_warn warning message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA (NHI) port of a switch provides access to the NVM of the host
controller (and devices starting from Intel Alpine Ridge). The NVM
contains also more complete DROM for the root switch including vendor
and device identification strings.
This will look for the DMA port capability for each switch and if found
populates sw->dma_port. We then teach tb_drom_read() to read the DROM
information from NVM if available for the root switch.
The DMA port capability also supports upgrading the NVM for both host
controller and devices which will be added in subsequent patches.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device DROM contains name of the vendor and device among other
things. Extract this information and expose it to the userspace via two
new attributes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently tb_drom_parse_entry() is only able to parse drom entries of
type TB_DROM_ENTRY_PORT. Rename it to tb_drom_parse_entry_port().
Fold tb_drom_parse_port_entry() into it.
Its return value is currently ignored. Evaluate it and abort parsing on
error.
Change tb_drom_parse_entries() to accommodate for parsing of other entry
types than TB_DROM_ENTRY_PORT.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are devices out there where CRC32 of the DROM is not correct. One
reason for this is that the ICM firmware does not validate it and it
seems that neither does the Apple driver. To be able to support such
devices we continue parsing the DROM contents regardless of whether
CRC32 failed or not. We still keep the warning there.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt domain consists of switches that are connected to each
other, forming a bus. This will convert each switch into a real Linux
device structure and adds them to the domain. The advantage here is
that we get all the goodies from the driver core, like reference
counting and sysfs hierarchy for free.
Also expose device identification information to the userspace via new
sysfs attributes.
In order to support internal connection manager (ICM) we separate switch
configuration into its own function (tb_switch_configure()) which is
only called by the existing native connection manager implementation
used on Macs.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DROM version 2 is compatible with the previous generation so no need to
warn about that.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least Falcon Ridge when in host mode does not have any kind of DROM
available and reading DROM offset returns 0 for these. Do not try to
read DROM any further in that case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Macs with Thunderbolt 1 do not have a unit-specific DROM: The DROM is
empty with uid 0x1000000000000. (Apple started factory-burning a unit-
specific DROM with Thunderbolt 2.)
Instead, the NHI EFI driver supplies a DROM in a device property. Use
it if available. It's only available when booting with the efistub.
If it's not available, silently fall back to our hardcoded DROM.
The size of the DROM is always 256 bytes. The number is hardcoded into
the NHI EFI driver. This commit can deal with an arbitrary size however,
just in case they ever change that.
Background information: The EFI firmware volume contains ROM files for
the NHI, GMUX and several other chips as well as key material. This
strategy allows Apple to deploy ROM or key updates by simply publishing
an EFI firmware update on their website. Drivers do not access those
files directly but rather through a file server via EFI protocol
AC5E4829-A8FD-440B-AF33-9FFE013B12D8. Files are identified by GUID, the
NHI DROM has 339370BD-CFC6-4454-8EF7-704653120818.
The NHI EFI driver amends that file with a unit-specific uid. The uid
has 64 bit but its entropy is much lower: 24 bit represent the model,
24 bit are taken from a serial number, 16 bit are fixed. The NHI EFI
driver obtains the serial number via the DataHub protocol, copies it
into the DROM, calculates the CRC and submits the result as a device
property.
A modification is needed in the resume code where we currently read the
uid of all switches in the hierarchy to detect plug events that occurred
during sleep. On Thunderbolt 1 root switches this will now lead to a
mismatch between the uid of the empty DROM and the EFI DROM. Exempt the
root switch from this check: It's built in, so the uid should never
change. However we continue to *read* the uid of the root switch, this
seems like a good way to test its reachability after resume.
Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1]
Tested-by: Pierre Moreau <pierre.morrow@free.fr> [MacBookPro11,3]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pedro Vilaça <reverser@put.as>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112213237.8804-10-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If tb_drom_read() fails, sw->drom is freed but not set to NULL. sw->drom
is then freed again in the error path of tb_switch_alloc().
The bug can be triggered by unplugging a thunderbolt device shortly after
it is detected by the thunderbolt driver.
Clear sw->drom if tb_drom_read() fails.
[bhelgaas: add Fixes:, stable versions of interest]
Fixes: 343fcb8c70 ("thunderbolt: Fix nontrivial endpoint devices.")
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.17+
CC: Lukas Wunner <lukas@wunner.de>
Add support for the 1st gen Light Ridge controller, which is built into
these systems:
iMac12,1 2011 21.5"
iMac12,2 2011 27"
Macmini5,1 2011 i5 2.3 GHz
Macmini5,2 2011 i5 2.5 GHz
Macmini5,3 2011 i7 2.0 GHz
MacBookPro8,1 2011 13"
MacBookPro8,2 2011 15"
MacBookPro8,3 2011 17"
MacBookPro9,1 2012 15"
MacBookPro9,2 2012 13"
Light Ridge (CV82524) was the very first copper Thunderbolt controller,
introduced 2010 alongside its fiber-optic cousin Light Peak (CVL2510).
Consequently the chip suffers from some teething troubles:
- MSI is broken for hotplug signaling on the downstream bridges: The chip
just never sends an interrupt. It requests 32 MSIs for each of its six
bridges and the pcieport driver only allocates one per bridge. However
I've verified that even if 32 MSIs are allocated there's no interrupt
on hotplug. The only option is thus to disable MSI, which is also what
OS X does. Apparently all Thunderbolt chips up to revision 1 of Cactus
Ridge 4C are plagued by this issue so quirk those as well.
- The chip supports a maximum hop_count of 32, unlike its successors
which support only 12. Fixup ring_interrupt_active() to cope with
values >= 32.
- Another peculiarity is that the chip supports a maximum of 13 ports
whereas its successors support 12. However the additional port (#5)
seems to be unusable as reading its TB_CFG_PORT config space results in
TB_CFG_ERROR_INVALID_CONFIG_SPACE. Add a quirk to mark the port
disabled on the root switch, assuming that's necessary on all Macs
using this chip.
Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1]
Tested-by: William Brown <william@blackhats.net.au> [MacBookPro8,2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Fix typo in tb_cfg_print_error() message. Fix bytecount in struct
tb_drom_entry_port comment. Replace magic number in tb_switch_alloc().
Rename tb_sw_set_unpplugged() and TB_CAL_IECS to fix typos.
[bhelgaas: no functional change intended]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
tb_eeprom_get_drom_offset is local to this file.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Force enum tb_drom_entry_type to unsigned to fix the following error:
drivers/thunderbolt/eeprom.c:202:39: error: dubious one-bit signed bitfield
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The result of "sizeof(struct tb_drom_entry_port)" is a size_t, which
is not necessarily the same as 'long', so we should use the appropriate
%z format string instead of %l.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All Thunderbolt switches (except the root switch) contain a drom which
contains information about the device. Right now we only read the UID.
Add code to read and parse this drom. For now we are only interested in
which ports are disabled and which ports are "dual link ports" (a
physical thunderbolt port/socket contains two such ports).
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add eeprom access code and read the uid during switch initialization.
The UID will be used to check device identity after suspend.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
