o Use D3 reset context deletion for NX2031, it cleans up
more resources in the firmware.
o Release rx buffers after hardware context has been reset.
o Delete tx context after rx context, some firmware control
commands are sent on tx context, so it should be the last
to go.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network driver for the SPI version of the Micrel KS8851
network chip.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the TCP connection handshake completes on the passive
side, a variety of state must be set up in the "child" sock,
including the key if MD5 authentication is being used. Fix TCP
for both address families to label the key with the peer's
destination address, rather than the address from the listening
sock, which is usually the wildcard.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix MD5 signature checking so that an IPv4 active open
to an IPv6 socket can succeed. In particular, use the
correct address family's signature generation function
for the SYN/ACK.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mac driver support for evaluation board based on w90p910.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel has used a stale email address of Andreas for a few years.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The web server does no longer exist, it's not on archive.org nor does there
seem to be any mirror.
MAINTAINERS | 1 -
1 files changed, 0 insertions(+), 1 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver received an EEM packet with CRC option enabled, driver must
compute and check the CRC of the Ethernet data. Previous version computes CRC
on Ethernet data plus the original CRC value. Skbuff is correctly trimed but
the old length is used when CRC is computed.
Signed-off-by: Vincent CUISSARD <vincent.cuissard@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove debug DPRINTK in DCB mode netlink interface.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change clears the address data block memory space, which is needed for
the 82598 which does not have a SAN MAC.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit changes to shutdown path broke startup on some systems.
revert commit c0bad0f2e4
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e912b1142b
(net: sk_prot_alloc() should not blindly overwrite memory)
took care of not zeroing whole new socket at allocation time.
sock_copy() is another spot where we should be very careful.
We should not set refcnt to a non null value, until
we are sure other fields are correctly setup, or
a lockless reader could catch this socket by mistake,
while not fully (re)initialized.
This patch puts sk_node & sk_refcnt to the very beginning
of struct sock to ease sock_copy() & sk_prot_alloc() job.
We add appropriate smp_wmb() before sk_refcnt initializations
to match our RCU requirements (changes to sock keys should
be committed to memory before sk_refcnt setting)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E100 places it's RX packet descriptors inside skb->data and uses them
with bidirectional streaming DMA mapping. Unfortunately it fails to
transfer skb->data ownership to the device after it reads the
descriptor's status, breaking on non-coherent (e.g., ARM) platforms.
This have to be converted to use coherent memory for the descriptors.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bonding device forbids slave device of different types under the same
master.
However, it is possible for a bonding master to change type during its
lifetime. This can be either from ARPHRD_ETHER to ARPHRD_INFINIBAND
or the other way arround. The change of type requires device level
multicast address cleanup because device level multicast addresses
depend on the device type.
The patch adds a call to dev_close() before the bonding master changes
type and dev_open() just after that.
In the example below I enslaved an IPoIB device (ib0) under
bond0. Since each bonding master starts as device of type ARPHRD_ETHER
by default, a change of type occurs when ib0 is enslaved.
This is how /proc/net/dev_mcast looks like without the patch
5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05
5 bond0 1 0 01005e000116
5 bond0 1 0 01005e7ffffd
5 bond0 1 0 01005e000001
5 bond0 1 0 333300000001
6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05
6 ib0 1 0 333300000001
6 ib0 1 0 01005e000001
6 ib0 1 0 01005e7ffffd
6 ib0 1 0 01005e000116
6 ib0 1 0 00ffffffff12401bffff00000000000000000001
6 ib0 1 0 00ffffffff12601bffff00000000000000000001
and this is how it looks like after the patch.
5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05
5 bond0 1 0 00ffffffff12601bffff00000000000000000001
5 bond0 1 0 00ffffffff12401bffff0000000000000ffffffd
5 bond0 1 0 00ffffffff12401bffff00000000000000000116
5 bond0 1 0 00ffffffff12401bffff00000000000000000001
6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05
6 ib0 1 0 00ffffffff12401bffff00000000000000000116
6 ib0 1 0 00ffffffff12401bffff0000000000000ffffffd
6 ib0 2 0 00ffffffff12401bffff00000000000000000001
6 ib0 2 0 00ffffffff12601bffff00000000000000000001
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parentheses are required or the comparison occurs before the bitand.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a slab cache uses SLAB_DESTROY_BY_RCU, we must be careful when allocating
objects, since slab allocator could give a freed object still used by lockless
readers.
In particular, nf_conntrack RCU lookups rely on ct->tuplehash[xxx].hnnode.next
being always valid (ie containing a valid 'nulls' value, or a valid pointer to next
object in hash chain.)
kmem_cache_zalloc() setups object with NULL values, but a NULL value is not valid
for ct->tuplehash[xxx].hnnode.next.
Fix is to call kmem_cache_alloc() and do the zeroing ourself.
As spotted by Patrick, we also need to make sure lookup keys are committed to
memory before setting refcount to 1, or a lockless reader could get a reference
on the old version of the object. Its key re-check could then pass the barrier.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add appropriate MODULE_ALIAS() to facilitate autoloading of can protocol drivers
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Acked-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a use after free bug in can protocol drivers
The release functions of the can protocol drivers lack a call to
sock_orphan() which leads to referencing freed memory under certain
circumstances.
This patch fixes a bug reported here:
https://lists.berlios.de/pipermail/socketcan-users/2009-July/000985.html
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Acked-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit adeab1afb7.
As Alan Cox explained, the TTY layer changes that went recently
to get rid of the tty->low_latency stuff fixes this already,
and even for -stable it's the ->low_latency changes that should
go in to fix this, rather than this patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the correct function call for skb_reserve in the comment for
NET_IP_ALIGN.
Signed-off-by: Tobias Klauser <klto@zhaw.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
spin_unlock_irq() will enable interrupt in net_send_packet(),
this patch changes it to spin_lock_irqsave/spin_lock_irqrestore,
so that it doesn't enable interrupts when already disabled,
and netconsole would work properly over cs89x0/isa-skeleton.
Call trace:
netconsole write_msg()
{
...
-> spin_lock_irqsave();
-> netpoll_send_udp()
-> netpoll_send_skb()
-> net_send_packet()
->...
-> spin_unlock_irqrestore();
...
}
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't forget to unlock a mutex in phy_scan_fixups on a fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes two bugs:
- ToS/DiffServ inheritance was unintentionally activated when using impair fixed ToS values
- ECN bit was lost during ToS/DiffServ inheritance
Signed-off-by: Andreas Jaggi <aj@open.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
forward declaration of inline function should be avoided, or
old gcc cannot compile.
Reported-by: Teck Choon Giam <giamteckchoon@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix duplicate testing of MCAST flag
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guido Trentalancia reports:
I am trying to use the kiss driver in the Linux kernel that is being
shipped with Fedora 10 but unfortunately I get the following oops:
mkiss: AX.25 Multikiss, Hans Albas PE1AYX
mkiss: ax0: crc mode is auto.
ADDRCONF(NETDEV_CHANGE): ax0: link becomes ready
------------[ cut here ]------------
WARNING: at kernel/softirq.c:77 __local_bh_disable+0x2f/0x83() (Not
tainted)
[...]
unloaded: microcode]
Pid: 0, comm: swapper Not tainted 2.6.27.25-170.2.72.fc10.i686 #1
[<c042ddfb>] warn_on_slowpath+0x65/0x8b
[<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
[<c04228b4>] ? __enqueue_entity+0xe3/0xeb
[<c042431e>] ? enqueue_entity+0x203/0x20b
[<c0424361>] ? enqueue_task_fair+0x3b/0x3f
[<c041f88c>] ? resched_task+0x3a/0x6e
[<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
[<c06ab4e2>] ? _spin_lock_bh+0xb/0x16
[<c043255b>] __local_bh_disable+0x2f/0x83
[<c04325ba>] local_bh_disable+0xb/0xd
[<c06ab4e2>] _spin_lock_bh+0xb/0x16
[<f8b6f600>] mkiss_receive_buf+0x2fb/0x3a6 [mkiss]
[<c0572a30>] flush_to_ldisc+0xf7/0x198
[<c0572b12>] tty_flip_buffer_push+0x41/0x51
[<f89477f2>] ftdi_process_read+0x375/0x4ad [ftdi_sio]
[<f8947a5a>] ftdi_read_bulk_callback+0x130/0x138 [ftdi_sio]
[<c05d4bec>] usb_hcd_giveback_urb+0x63/0x93
[<c05ea290>] uhci_giveback_urb+0xe5/0x15f
[<c05eaabf>] uhci_scan_schedule+0x52e/0x767
[<c05f6288>] ? psmouse_handle_byte+0xc/0xe5
[<c054df78>] ? acpi_ev_gpe_detect+0xd6/0xe1
[<c05ec5b0>] uhci_irq+0x110/0x125
[<c05d4834>] usb_hcd_irq+0x40/0xa3
[<c0465313>] handle_IRQ_event+0x2f/0x64
[<c046642b>] handle_level_irq+0x74/0xbe
[<c04663b7>] ? handle_level_irq+0x0/0xbe
[<c0406e6e>] do_IRQ+0xc7/0xfe
[<c0405668>] common_interrupt+0x28/0x30
[<c056821a>] ? acpi_idle_enter_simple+0x162/0x19d
[<c0617f52>] cpuidle_idle_call+0x60/0x92
[<c0403c61>] cpu_idle+0x101/0x134
[<c069b1ba>] rest_init+0x4e/0x50
=======================
---[ end trace b7cc8076093467ad ]---
------------[ cut here ]------------
WARNING: at kernel/softirq.c:136 _local_bh_enable_ip+0x3d/0xc4()
[...]
Pid: 0, comm: swapper Tainted: G W 2.6.27.25-170.2.72.fc10.i686
[<c042ddfb>] warn_on_slowpath+0x65/0x8b
[<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
[<c04228b4>] ? __enqueue_entity+0xe3/0xeb
[<c042431e>] ? enqueue_entity+0x203/0x20b
[<c0424361>] ? enqueue_task_fair+0x3b/0x3f
[<c041f88c>] ? resched_task+0x3a/0x6e
[<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38
[<c06ab4e2>] ? _spin_lock_bh+0xb/0x16
[<f8b6f642>] ? mkiss_receive_buf+0x33d/0x3a6 [mkiss]
[<c04325f9>] _local_bh_enable_ip+0x3d/0xc4
[<c0432688>] local_bh_enable_ip+0x8/0xa
[<c06ab54d>] _spin_unlock_bh+0x11/0x13
[<f8b6f642>] mkiss_receive_buf+0x33d/0x3a6 [mkiss]
[<c0572a30>] flush_to_ldisc+0xf7/0x198
[<c0572b12>] tty_flip_buffer_push+0x41/0x51
[<f89477f2>] ftdi_process_read+0x375/0x4ad [ftdi_sio]
[<f8947a5a>] ftdi_read_bulk_callback+0x130/0x138 [ftdi_sio]
[<c05d4bec>] usb_hcd_giveback_urb+0x63/0x93
[<c05ea290>] uhci_giveback_urb+0xe5/0x15f
[<c05eaabf>] uhci_scan_schedule+0x52e/0x767
[<c05f6288>] ? psmouse_handle_byte+0xc/0xe5
[<c054df78>] ? acpi_ev_gpe_detect+0xd6/0xe1
[<c05ec5b0>] uhci_irq+0x110/0x125
[<c05d4834>] usb_hcd_irq+0x40/0xa3
[<c0465313>] handle_IRQ_event+0x2f/0x64
[<c046642b>] handle_level_irq+0x74/0xbe
[<c04663b7>] ? handle_level_irq+0x0/0xbe
[<c0406e6e>] do_IRQ+0xc7/0xfe
[<c0405668>] common_interrupt+0x28/0x30
[<c056821a>] ? acpi_idle_enter_simple+0x162/0x19d
[<c0617f52>] cpuidle_idle_call+0x60/0x92
[<c0403c61>] cpu_idle+0x101/0x134
[<c069b1ba>] rest_init+0x4e/0x50
=======================
---[ end trace b7cc8076093467ad ]---
mkiss: ax0: Trying crc-smack
mkiss: ax0: Trying crc-flexnet
The issue was, that the locking code in mkiss was assuming it was only
ever being called in process or bh context. Fixed by converting the
involved locking code to use irq-safe locks.
Review of other networking line disciplines shows that 6pack, both sync
and async PPP and STRIP have similar issues. The ppp_async one is the
most interesting one as it sorts out half of the issue as far back as
2004 in commit http://git.kernel.org/?p=linux/kernel/git/tglx/history.git;a=commitdiff;h=2996d8deaeddd01820691a872550dc0cfba0c37d
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Guido Trentalancia <guido@trentalancia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev() used to install a default implementation of this
operation, but it must now be explicitly installed in struct
net_device_ops.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev() used to install default implementations of these
operations, but they must now be explicitly installed in struct
net_device_ops.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sit module makes use of skb->dst in it's xmit function, so since
93f154b594 ("net: release dst entry in dev_hard_start_xmit()") sit
tunnels are broken, because the flag IFF_XMIT_DST_RELEASE is not
unset.
This patch unsets that flag for sit devices to fix this
regression.
Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 2b85a34e91
(net: No more expensive sock_hold()/sock_put() on each tx)
we do not take any more references on sk->sk_refcnt on outgoing packets.
I forgot to delete two __sock_put() from ip_push_pending_frames()
and ip6_push_pending_frames().
Reported-by: Emil S Tantilov <emils.tantilov@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Emil S Tantilov <emils.tantilov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some sockets use SLAB_DESTROY_BY_RCU, and our RCU code correctness
depends on sk->sk_nulls_node.next being always valid. A NULL
value is not allowed as it might fault a lockless reader.
Current sk_prot_alloc() implementation doesnt respect this hypothesis,
calling kmem_cache_alloc() with __GFP_ZERO. Just call memset() around
the forbidden field.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c3a8c5b6 ("cxgb3: move away from LLTX") exposed a bug in how
cxgb3 looks up the netdev_queue it stashes away in a qset during
initialization. For multiport devices, the TX queue index it uses is
offset by the first_qset index of each port. This leads to a crash
once LLTX is removed, since hard_start_xmit is called with one TX
queue lock held, while the TX reclaim timer task grabs a different
(wrong) TX queue lock when it frees skbs.
Fix this by removing the first_qset offset used to look up the TX
queue passed into t3_sge_alloc_qset() from setup_sge_qsets().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coexistence of Fiber Channel over Ethernet (FCoE) and Flow Director (FDIR)
in 82599 and remove the disabling of FDIR when FCoE is enabled.
Currently, FDIR is turned off when FCoE is enabled under the assumption that
FCoE is always enabled with DCB being turned on. However, FDIR does not have
to be turned off all the time when FCoE is enabled since FCoE can be enabled
without DCB being turned on, e.g., use link pause only. This patch makes sure
that when DCB is turned on or off, FDIR is turned on or off correspondingly;
and when FCoE is enabled, it does not disable FDIR, rather, it will have FDIR
set up properly so FCoE and FDIR can coexist regardless of DCB being on or off.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding smp_mb__after_lock define to be used as a smp_mb call after
a lock.
Making it nop for x86, since {read|write|spin}_lock() on x86 are
full memory barriers.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding memory barrier after the poll_wait function, paired with
receive callbacks. Adding fuctions sock_poll_wait and sk_has_sleeper
to wrap the memory barrier.
Without the memory barrier, following race can happen.
The race fires, when following code paths meet, and the tp->rcv_nxt
and __add_wait_queue updates stay in CPU caches.
CPU1 CPU2
sys_select receive packet
... ...
__add_wait_queue update tp->rcv_nxt
... ...
tp->rcv_nxt check sock_def_readable
... {
schedule ...
if (sk->sk_sleep && waitqueue_active(sk->sk_sleep))
wake_up_interruptible(sk->sk_sleep)
...
}
If there was no cache the code would work ok, since the wait_queue and
rcv_nxt are opposit to each other.
Meaning that once tp->rcv_nxt is updated by CPU2, the CPU1 either already
passed the tp->rcv_nxt check and sleeps, or will get the new value for
tp->rcv_nxt and will return with new data mask.
In both cases the process (CPU1) is being added to the wait queue, so the
waitqueue_active (CPU2) call cannot miss and will wake up CPU1.
The bad case is when the __add_wait_queue changes done by CPU1 stay in its
cache, and so does the tp->rcv_nxt update on CPU2 side. The CPU1 will then
endup calling schedule and sleep forever if there are no more data on the
socket.
Calls to poll_wait in following modules were ommited:
net/bluetooth/af_bluetooth.c
net/irda/af_irda.c
net/irda/irnet/irnet_ppp.c
net/mac80211/rc80211_pid_debugfs.c
net/phonet/socket.c
net/rds/af_rds.c
net/rfkill/core.c
net/sunrpc/cache.c
net/sunrpc/rpc_pipe.c
net/tipc/socket.c
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using early netconsole and gianfar driver this error pops up:
netconsole: timeout waiting for carrier
It appears that net/core/netpoll.c:netpoll_setup() is using
cond_resched() in a loop waiting for a carrier.
The thing is that cond_resched() is a no-op when system_state !=
SYSTEM_RUNNING, and so drivers/net/phy/phy.c's state_queue is never
scheduled, therefore link detection doesn't work.
I belive that the main problem is in cond_resched()[1], but despite
how the cond_resched() story ends, it might be a good idea to call
msleep(1) instead of cond_resched(), as suggested by Andrew Morton.
[1] http://lkml.org/lkml/2009/7/7/463
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix the following 'make includecheck' warning:
include/linux/rfkill.h: linux/types.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the mainline kernel, p54usb will fail because the TX queue length can
become < 0. This problem has been reported as Bugzilla #13725. The failure
is expressed by the following message in the logs:
WARNING: at net/mac80211/tx.c:1325 ieee80211_tx+0x23c/0x298 [mac80211]()
Hardware name: HP Pavilion dv2700 Notebook PC
tx refused but queue active
This problem has been recently observed in the wireless-testing tree, where
a full solution is being tested. That fix is too invasive for 2.6.31-rcX,
but the simple change supplied here will prevent the failure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Atheros top level menu needs a "depends WLAN_80211" to properly indent
within menuconfig and xconfig interfaces.
This is purely a visual issue but it effects all subsequent drivers.
The issue is the top level menu does not include a dependency on
WLAN_80211 so within the tree structure, Atheros is at the same level as
WLAN_80211 but when WLAN_80211 collapsed, the menu disappears along with
all subsequent drives, so it is really a subordinate.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These two functions no longer exist in mac80211,
so trying to insert them generates warnings in
the document.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a race condition -- started can be set to true
before channel is set due to the way mac80211 callbacks
currently work (->start should probably pass the channel
we would like to have initially). For now simply add a
check to hwsim to avoid dereferencing the NULL channel
pointer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: Clyde McPherson <ccmcphe@verizon.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: Clyde McPherson <ccmcphe@verizon.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yevgen Kotikov reported success on the sourceforge zd1211-devs list
with the following details:
Brand/retail: SONY IFU-WLM2
USB-IDs: Vendor: 0x054C Device: 0x0257
chip ID: zd1211b chip 054c:0257 v4802 high 00-0b-6b AL2230_RF pa0 -----
FCC ID: unknown
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Yevgen Kotikov <yevgen.kotikov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a shuttle machine here we got 07b8:6001 device, handled by zd1211rw, which does not work.
Scanning is OK but association does not work, we get "direct probe to AP xxx timed out"
It appears that this simple patch makes the device work perfectly.
This id was already there in initial import of the driver so I don't know if it has ever been
working as ZD1211 (which would mean they changed it and kept the id :( ).
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
