Due to the fact that ic_dev->dev is kept open in ic_close_dev, I had
thought that ic_dev will not be freed either. But that is not the case,
but instead "everybody dies" when ipconfig cleans up, and just the
net_device behind ic_dev->dev remains allocated but not ic_dev itself.
This is a problem because in ic_close_devs, for every net device that
we're about to close, we compare it against the list of lower interfaces
of ic_dev, to figure out whether we should close it or not. But since
ic_dev itself is subject to freeing, this means that at some point in
the middle of the list of ipconfig interfaces, ic_dev will have been
freed, and we would be still attempting to iterate through its list of
lower interfaces while checking whether to bring down the remaining
ipconfig interfaces.
There are multiple ways to avoid the use-after-free: we could delay
freeing ic_dev until the very end (outside the while loop). Or an even
simpler one: we can observe that we don't need ic_dev when iterating
through its lowers, only ic_dev->dev, structure which isn't ever freed.
So, by keeping ic_dev->dev in a variable assigned prior to freeing
ic_dev, we can avoid all use-after-free issues.
Fixes: 46acf7bdbc ("Revert "net: ipv4: handle DSA enabled master network devices"")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even when implementing RFC 6056 3.3.4 (Algorithm 4: Double-Hash
Port Selection Algorithm), a patient attacker could still be able
to collect enough state from an otherwise idle host.
Idea of this patch is to inject some noise, in the
cases __inet_hash_connect() found a candidate in the first
attempt.
This noise should not significantly reduce the collision
avoidance, and should be zero if connection table
is already well used.
Note that this is not implementing RFC 6056 3.3.5
because we think Algorithm 5 could hurt typical
workloads.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Dworken <ddworken@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 6056 (Recommendations for Transport-Protocol Port Randomization)
provides good summary of why source selection needs extra care.
David Dworken reminded us that linux implements Algorithm 3
as described in RFC 6056 3.3.3
Quoting David :
In the context of the web, this creates an interesting info leak where
websites can count how many TCP connections a user's computer is
establishing over time. For example, this allows a website to count
exactly how many subresources a third party website loaded.
This also allows:
- Distinguishing between different users behind a VPN based on
distinct source port ranges.
- Tracking users over time across multiple networks.
- Covert communication channels between different browsers/browser
profiles running on the same computer
- Tracking what applications are running on a computer based on
the pattern of how fast source ports are getting incremented.
Section 3.3.4 describes an enhancement, that reduces
attackers ability to use the basic information currently
stored into the shared 'u32 hint'.
This change also decreases collision rate when
multiple applications need to connect() to
different destinations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Dworken <ddworken@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2021-02-09
1) Support TSO on xfrm interfaces.
From Eyal Birger.
2) Variable calculation simplifications in esp4/esp6.
From Jiapeng Chong / Jiapeng Zhong.
3) Fix a return code in xfrm_do_migrate.
From Zheng Yongjun.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the value '2' to 'fib_notify_on_flag_change' to allow sending
notifications only for failed route installation.
Separate value is added for such notifications because there are less of
them, so they do not impact performance and some users will find them more
important.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel, but not
necessarily in hardware.
The asynchronous nature of route installation in hardware can lead to a
routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
To avoid such cases, previous patch set added the ability to emit
RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed, this behavior is controlled by sysctl.
With the above mentioned behavior, it is possible to know from user-space
if the route was offloaded, but if the offload fails there is no indication
to user-space. Following a failure, a routing daemon will wait indefinitely
for a notification that will never come.
This patch adds an "offload_failed" indication to IPv4 routes, so that
users will have better visibility into the offload process.
'struct fib_alias', and 'struct fib_rt_info' are extended with new field
that indicates if route offload failed. Note that the new field is added
using unused bit and therefore there is no need to increase structs size.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
1) Remove indirection and use nf_ct_get() instead from nfnetlink_log
and nfnetlink_queue, from Florian Westphal.
2) Add weighted random twos choice least-connection scheduling for IPVS,
from Darby Payne.
3) Add a __hash placeholder in the flow tuple structure to identify
the field to be included in the rhashtable key hash calculation.
4) Add a new nft_parse_register_load() and nft_parse_register_store()
to consolidate register load and store in the core.
5) Statify nft_parse_register() since it has no more module clients.
6) Remove redundant assignment in nft_cmp, from Colin Ian King.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next:
netfilter: nftables: remove redundant assignment of variable err
netfilter: nftables: statify nft_parse_register()
netfilter: nftables: add nft_parse_register_store() and use it
netfilter: nftables: add nft_parse_register_load() and use it
netfilter: flowtable: add hash offset field to tuple
ipvs: add weighted random twos choice algorithm
netfilter: ctnetlink: remove get_ct indirection
====================
Link: https://lore.kernel.org/r/20210206015005.23037-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 728c02089a.
Since 2015 DSA has gained more integration with the network stack, we
can now have the same functionality without explicitly open-coding for
it:
- It now opens the DSA master netdevice automatically whenever a user
netdevice is opened.
- The master and switch interfaces are coupled in an upper/lower
hierarchy using the netdev adjacency lists.
In the nfsroot example below, the interface chosen by autoconfig was
swp3, and every interface except that and the DSA master, eth1, was
brought down afterwards:
[ 8.714215] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:10] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 8.978041] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:11] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 9.246134] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:12] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 9.486203] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:13] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 9.512827] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode
[ 9.521047] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control off
[ 9.530382] device eth1 entered promiscuous mode
[ 9.535452] DSA: tree 0 setup
[ 9.539777] printk: console [netcon0] enabled
[ 9.544504] netconsole: network logging started
[ 9.555047] fsl_enetc 0000:00:00.2 eth1: configuring for fixed/internal link mode
[ 9.562790] fsl_enetc 0000:00:00.2 eth1: Link is Up - 1Gbps/Full - flow control off
[ 9.564661] 8021q: adding VLAN 0 to HW filter on device bond0
[ 9.637681] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.0:02] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
[ 9.655679] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode
[ 9.666611] mscc_felix 0000:00:00.5 swp0: configuring for inband/qsgmii link mode
[ 9.676216] 8021q: adding VLAN 0 to HW filter on device swp0
[ 9.682086] mscc_felix 0000:00:00.5 swp1: configuring for inband/qsgmii link mode
[ 9.690700] 8021q: adding VLAN 0 to HW filter on device swp1
[ 9.696538] mscc_felix 0000:00:00.5 swp2: configuring for inband/qsgmii link mode
[ 9.705131] 8021q: adding VLAN 0 to HW filter on device swp2
[ 9.710964] mscc_felix 0000:00:00.5 swp3: configuring for inband/qsgmii link mode
[ 9.719548] 8021q: adding VLAN 0 to HW filter on device swp3
[ 9.747811] Sending DHCP requests ..
[ 12.742899] mscc_felix 0000:00:00.5 swp1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 12.743828] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control off
[ 12.747062] IPv6: ADDRCONF(NETDEV_CHANGE): swp1: link becomes ready
[ 12.755216] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 12.766603] IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready
[ 12.783188] mscc_felix 0000:00:00.5 swp2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 12.785354] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 12.799535] IPv6: ADDRCONF(NETDEV_CHANGE): swp2: link becomes ready
[ 13.803141] mscc_felix 0000:00:00.5 swp3: Link is Up - 1Gbps/Full - flow control rx/tx
[ 13.811646] IPv6: ADDRCONF(NETDEV_CHANGE): swp3: link becomes ready
[ 15.452018] ., OK
[ 15.470336] IP-Config: Got DHCP answer from 10.0.0.1, my address is 10.0.0.39
[ 15.477887] IP-Config: Complete:
[ 15.481330] device=swp3, hwaddr=00:04:9f:05:de:0a, ipaddr=10.0.0.39, mask=255.255.255.0, gw=10.0.0.1
[ 15.491846] host=10.0.0.39, domain=(none), nis-domain=(none)
[ 15.498429] bootserver=10.0.0.1, rootserver=10.0.0.1, rootpath=
[ 15.498481] nameserver0=8.8.8.8
[ 15.627542] fsl_enetc 0000:00:00.0 eth0: Link is Down
[ 15.690903] mscc_felix 0000:00:00.5 swp0: Link is Down
[ 15.745216] mscc_felix 0000:00:00.5 swp1: Link is Down
[ 15.800498] mscc_felix 0000:00:00.5 swp2: Link is Down
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When enabling encap for a ipv6 socket without udp_encap_needed_key
increased, UDP GRO won't work for v4 mapped v6 address packets as
sk will be NULL in udp4_gro_receive().
This patch is to enable it by increasing udp_encap_needed_key for
v6 sockets in udp_tunnel_encap_enable(), and correspondingly
decrease udp_encap_needed_key in udpv6_destroy_sock().
v1->v2:
- add udp_encap_disable() and export it.
v2->v3:
- add the change for rxrpc and bareudp into one patch, as Alex
suggested.
v3->v4:
- move rxrpc part to another patch.
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit fixes the errores reported when building for powerpc:
ERROR: modpost: "ip6_dst_check" [vmlinux] is a static EXPORT_SYMBOL
ERROR: modpost: "ipv4_dst_check" [vmlinux] is a static EXPORT_SYMBOL
ERROR: modpost: "ipv4_mtu" [vmlinux] is a static EXPORT_SYMBOL
ERROR: modpost: "ip6_mtu" [vmlinux] is a static EXPORT_SYMBOL
Fixes: f67fbeaebd ("net: use indirect call helpers for dst_mtu")
Fixes: bbd807dfbf ("net: indirect call helpers for ipv4/ipv6 dst_check functions")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Link: https://lore.kernel.org/r/20210204181839.558951-2-brianvv@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip6_dst_check and ipv4_dst_check
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip6_mtu and ipv4_mtu
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip6_output and ip_output
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip_local_deliver and ip6_input
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
inet_gro_receive() and inet_gro_complete() are part
of GRO engine which can not be modular.
Similarly, inet_gso_segment() does not need to be exported,
being part of GSO stack.
In other words, net/ipv6/ip6_offload.o is part of vmlinux,
regardless of CONFIG_IPV6.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20210202154145.1568451-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel,
but not necessarily in hardware.
The asynchronous nature of route installation in hardware can lead to a
routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
It is also possible for a route already installed in hardware to change
its action and therefore its flags. For example, a host route that is
trapping packets can be "promoted" to perform decapsulation following
the installation of an IPinIP/VXLAN tunnel.
Emit RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed. The aim is to provide an indication to user-space
(e.g., routing daemons) about the state of the route in hardware.
Introduce a sysctl that controls this behavior.
Keep the default value at 0 (i.e., do not emit notifications) for several
reasons:
- Multiple RTM_NEWROUTE notification per-route might confuse existing
routing daemons.
- Convergence reasons in routing daemons.
- The extra notifications will negatively impact the insertion rate.
- Not all users are interested in these notifications.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Publish fib_nlmsg_size() to allow it to be used later on from
fib_alias_hw_flags_set().
Remove the inline keyword since it shouldn't be used inside C files.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fib_dump_info() does not change 'fri', so pass it as 'const'.
It will later allow us to invoke fib_dump_info() from
fib_alias_hw_flags_set().
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
UDP/IP header of UDP GROed frag_skbs are not updated even after NAT
forwarding. Only the header of head_skb from ip_finish_output_gso ->
skb_gso_segment is updated but following frag_skbs are not updated.
A call path skb_mac_gso_segment -> inet_gso_segment ->
udp4_ufo_fragment -> __udp_gso_segment -> __udp_gso_segment_list
does not try to update UDP/IP header of the segment list but copy
only the MAC header.
Update port, addr and check of each skb of the segment list in
__udp_gso_segment_list. It covers both SNAT and DNAT.
Fixes: 9fd1ff5d2a (udp: Support UDP fraglist GRO/GSO.)
Signed-off-by: Dongseok Yi <dseok.yi@samsung.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Link: https://lore.kernel.org/r/1611962007-80092-1-git-send-email-dseok.yi@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev->hard_header_len for tunnel interface is set only when header_ops
are set too and already contains full overhead of any tunnel encapsulation.
That's why there is not need to use this overhead twice in mtu calc.
Fixes: fdafed4599 ("ip_gre: set dev->hard_header_len and dev->needed_headroom properly")
Reported-by: Slava Bacherikov <mail@slava.cc>
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Link: https://lore.kernel.org/r/1611959267-20536-1-git-send-email-vfedorenko@novek.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use cache friendly helpers to better use cpu caches
while reading /proc/net/netstat
Tested on a platform with 256 threads (AMD Rome)
Before: 305 usec spent in netstat_seq_show()
After: 130 usec spent in netstat_seq_show()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210128162145.1703601-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is to add csum offload support for gre header:
On the TX path in gre_build_header(), when CHECKSUM_PARTIAL's set
for inner proto, it will calculate the csum for outer proto, and
inner csum will be offloaded later. Otherwise, CHECKSUM_PARTIAL
and csum_start/offset will be set for outer proto, and the outer
csum will be offloaded later.
On the GSO path in gre_gso_segment(), when CHECKSUM_PARTIAL is
not set for inner proto and the hardware supports csum offload,
CHECKSUM_PARTIAL and csum_start/offset will be set for outer
proto, and outer csum will be offloaded later. Otherwise, it
will do csum for outer proto by calling gso_make_checksum().
Note that SCTP has to do the csum by itself for non GSO path in
sctp_packet_pack(), as gre_build_header() can't handle the csum
with CHECKSUM_PARTIAL set for SCTP CRC csum offload.
v1->v2:
- remove the SCTP part, as GRE dev doesn't support SCTP CRC CSUM
and it will always do checksum for SCTP in sctp_packet_pack()
when it's not a GSO packet.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Validation of messages for get / del of a next hop is the same as will be
validation of messages for get of a resilient next hop group bucket. The
difference is that policy for resilient next hop group buckets is a
superset of that used for next-hop get.
It is therefore possible to reuse the code that validates the nhmsg fields,
extracts the next-hop ID, and validates that. To that end, extract from
nh_valid_get_del_req() a helper __nh_valid_get_del_req() that does just
that.
Make the nlh argument const so that the function can be called from the
dump context, which only has a const nlh. Propagate the constness to
nh_valid_get_del_req().
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to allow different handling for next-hop tree dumper and for
bucket dumper, parameterize the next-hop tree walker with a callback. Add
rtm_dump_nexthop_cb() with just the bits relevant for next-hop tree
dumping.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extract from rtm_dump_nexthop() a helper to walk the next hop tree. A
separate function for this will be reusable from the bucket dumper.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dump operations need to keep state from one invocation to another. A
scratch area is dedicated for this purpose in the passed-in argument, cb,
namely via two aliased arrays, struct netlink_callback.args and .ctx.
Dumping of buckets will end up having to iterate over next hops as well,
and it would be nice to be able to reuse the iteration logic with the NH
dumper. The fact that the logic currently relies on fixed index to the
.args array, and the indices would have to be coordinated between the two
dumpers, makes this somewhat awkward.
To make the access patters clearer, introduce a helper struct with a NH
index, and instead of using the .args array directly, use it through this
structure.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Requests to dump nexthops have many attributes in common with those that
requests to dump buckets of resilient NH groups will have. However, they
have different policies. To allow reuse of this code, extract a
policy-agnostic wrapper out of nh_valid_dump_req(), and convert this
function into a thin wrapper around it.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Requests to dump nexthops have many attributes in common with those that
requests to dump buckets of resilient NH groups will have. In order to make
reuse of this code simpler, convert the code to use a single structure with
filtering configuration instead of passing around the parameters one by
one.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After there are several next-hop group types, initialization and
finalization of notifier type needs to reflect the actual type. Transform
nh_notifier_grp_info_init() and _fini() to make extending them easier.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently there are only two types of in-kernel nexthop notification.
The two are distinguished by the 'is_grp' boolean field in 'struct
nh_notifier_info'.
As more notification types are introduced for more next-hop group types, a
boolean is not an easily extensible interface. Instead, convert it to an
enum.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most of the code that deals with nexthop groups relies on the fact that the
group is of exactly one well-known type. Currently there is only one type,
"mpath", but as more next-hop group types come, it becomes desirable to
have a central place where the setting is validated. Introduce such place
into nexthop_create_group(), such that the check is done before the code
that relies on that invariant is invoked.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The values that a next-hop group needs to keep track of depend on the group
type. Introduce a union to separate fields specific to the mpath groups
from fields specific to other group types.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The logic for selecting path depends on the next-hop group type. Adapt the
nexthop_select_path() to dispatch according to the group type.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nexthop_free_mpath really should be nexthop_free_group. Rename it.
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This new function combines the netlink register attribute parser
and the load validation function.
This update requires to replace:
enum nft_registers sreg:8;
in many of the expression private areas otherwise compiler complains
with:
error: cannot take address of bit-field ‘sreg’
when passing the register field as reference.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix the following coccicheck warnings:
./net/ipv4/esp4_offload.c:288:32-34: WARNING !A || A && B is
equivalent to !A || B.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Upon receiving a cumulative ACK that changes the congestion state from
Disorder to Open, the TLP timer is not set. If the sender is app-limited,
it can only wait for the RTO timer to expire and retransmit.
The reason for this is that the TLP timer is set before the congestion
state changes in tcp_ack(), so we delay the time point of calling
tcp_set_xmit_timer() until after tcp_fastretrans_alert() returns and
remove the FLAG_SET_XMIT_TIMER from ack_flag when the RACK reorder timer
is set.
This commit has two additional benefits:
1) Make sure to reset RTO according to RFC6298 when receiving ACK, to
avoid spurious RTO caused by RTO timer early expires.
2) Reduce the xmit timer reschedule once per ACK when the RACK reorder
timer is set.
Fixes: df92c8394e ("tcp: fix xmit timer to only be reset if data ACKed/SACKed")
Link: https://lore.kernel.org/netdev/1611311242-6675-1-git-send-email-yangpc@wangsu.com
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/1611464834-23030-1-git-send-email-yangpc@wangsu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 9fd1ff5d2a ("udp: Support UDP fraglist GRO/GSO.") actually
not only added a support for fraglisted UDP GRO, but also tweaked
some logics the way that non-fraglisted UDP GRO started to work for
forwarding too.
Commit 2e4ef10f58 ("net: add GSO UDP L4 and GSO fraglists to the
list of software-backed types") added GSO UDP L4 to the list of
software GSO to allow virtual netdevs to forward them as is up to
the real drivers.
Tests showed that currently forwarding and NATing of plain UDP GRO
packets are performed fully correctly, regardless if the target
netdevice has a support for hardware/driver GSO UDP L4 or not.
Add the last element and allow to form plain UDP GRO packets if
we are on forwarding path, and the new NETIF_F_GRO_UDP_FWD is
enabled on a receiving netdevice.
If both NETIF_F_GRO_FRAGLIST and NETIF_F_GRO_UDP_FWD are set,
fraglisted GRO takes precedence. This keeps the current behaviour
and is generally more optimal for now, as the number of NICs with
hardware USO offload is relatively small.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TCP_USER_TIMEOUT is checked by the 0-window probe timer. As the
timer has backoff with a max interval of about two minutes, the
actual timeout for TCP_USER_TIMEOUT can be off by up to two minutes.
In this patch the TCP_USER_TIMEOUT is made more accurate by taking it
into account when computing the timer value for the 0-window probes.
This patch is similar to and builds on top of the one that made
TCP_USER_TIMEOUT accurate for RTOs in commit b701a99e43 ("tcp: Add
tcp_clamp_rto_to_user_timeout() helper to improve accuracy").
Fixes: 9721e709fa ("tcp: simplify window probe aborting on USER_TIMEOUT")
Signed-off-by: Enke Chen <enchen@paloaltonetworks.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210122191306.GA99540@localhost.localdomain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcp_recvmsg() uses the CMSG mechanism to receive control information
like packet receive timestamps. This patch adds CMSG fields to
struct tcp_zerocopy_receive, and provides receive timestamps
if available to the user.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At present, tcp_recvmsg() uses flags to track if any CMSGs are pending
and what those CMSGs are. These flags are currently magic numbers,
used only within tcp_recvmsg().
To prepare for receive timestamp support in tcp receive zerocopy,
gently refactor these magic numbers into enums.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds TCP_NLA_TTL to SCM_TIMESTAMPING_OPT_STATS that exports
the time-to-live or hop limit of the latest incoming packet with
SCM_TSTAMP_ACK. The value exported may not be from the packet that acks
the sequence when incoming packets are aggregated. Exporting the
time-to-live or hop limit value of incoming packets helps to estimate
the hop count of the path of the flow that may change over time.
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20210120204155.552275-1-ysseung@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is to let it always do CRC checksum in sctp_gso_segment()
by removing CRC flag from the dev features in gre_gso_segment() for
SCTP over GRE, just as it does in Commit 527beb8ef9 ("udp: support
sctp over udp in skb_udp_tunnel_segment") for SCTP over UDP.
It could set csum/csum_start in GSO CB properly in sctp_gso_segment()
after that commit, so it would do checksum with gso_make_checksum()
in gre_gso_segment(), and Commit 622e32b7d4 ("net: gre: recompute
gre csum for sctp over gre tunnels") can be reverted now.
Note that when need_csum is false, we can still leave CRC checksum
of SCTP to HW by not clearing this CRC flag if it's supported, as
Jakub and Alex noticed.
v1->v2:
- improve the changelog.
- fix "rev xmas tree" in varibles declaration.
v2->v3:
- remove CRC flag from dev features only when need_csum is true.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/00439f24d5f69e2c6fa2beadc681d056c15c258f.1610772251.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In __skb_udp_tunnel_segment(), when it's a SCTP over VxLAN/GENEVE
packet and need_csum is false, which means the outer udp checksum
doesn't need to be computed, csum_start and csum_offset could be
used by the inner SCTP CRC CSUM for SCTP HW CRC offload.
So this patch is to not remove the CRC flag from dev features when
need_csum is false.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/1e81b700642498546eaa3f298e023fd7ad394f85.1610776757.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This policy is currently only used for creation of new next hops and new
next hop groups. Rename it accordingly and remove the two attributes that
are not valid in that context: NHA_GROUPS and NHA_MASTER.
For consistency with other policies, do not mention policy array size in
the declarator, and replace NHA_MAX for ARRAY_SIZE as appropriate.
Note that with this commit, NHA_MAX and __NHA_MAX are not used anymore.
Leave them in purely as a user API.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This function uses the global nexthop policy, but only accepts four
particular attributes. Create a new policy that only includes the four
supported attributes, and use it. Convert the loop to a series of ifs.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This function uses the global nexthop policy only to then bounce all
arguments except for NHA_ID. Instead, just create a new policy that
only includes the one allowed attribute.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
