Enable support for system wakeup, by setting the wakeup capability for the
slot corresponding to the SDIO card. Users need to enable the wakeup
through the sysfs interface.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1623326486-25275-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'mmc_abort_tuning()' made me think tuning gets completely aborted.
However, it sends only a STOP cmd to cancel the current tuning cmd.
Tuning process may still continue after that. So, rename the function to
'mmc_send_abort_tuning()' to better reflect all this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210608180620.40059-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The card timing and the bus frequency are not changed atomically with
respect to calls to the set_clock() callback in the driver. The result
is the driver sees a transient state where there's a mismatch between
the two and thus the inputs to the phase correction calculation
formula are garbage.
Switch from dev_warn() to dev_dbg() to avoid noise in the normal case,
though the change does make bad configurations less likely to be
noticed.
Reported-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210607013020.85885-1-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_sprd_writew() was defined by never used in sdhci_ops:
drivers/mmc/host/sdhci-sprd.c:134:20: warning: unused function 'sdhci_sprd_writew'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210601095403.236007-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While initializing an UHS-I SD card, the mmc core first tries to switch to
1.8V I/O voltage, before it continues to change the settings for the bus
speed mode.
However, the current behaviour in the mmc core is inconsistent and doesn't
conform to the SD spec. More precisely, an SD card that supports UHS-I must
set both the SD_OCR_CCS bit and the SD_OCR_S18R bit in the OCR register
response. When switching to 1.8V I/O the mmc core correctly checks both of
the bits, but only the SD_OCR_S18R bit when changing the settings for bus
speed mode.
Rather than actually fixing the code to confirm to the SD spec, let's
deliberately deviate from it by requiring only the SD_OCR_S18R bit for both
parts. This enables us to support UHS-I for SDSC cards (outside spec),
which is actually being supported by some existing SDSC cards. Moreover,
this fixes the inconsistent behaviour.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Link: https://lore.kernel.org/r/CWXP265MB26803AE79E0AD5ED083BF2A6C4529@CWXP265MB2680.GBRP265.PROD.OUTLOOK.COM
Cc: stable@vger.kernel.org
[Ulf: Rewrote commit message and comments to clarify the changes]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since we don't use structure field layout randomization
the manual shuffling can affect some macros, in particular
container_of() against struct of_mmc_spi, which becomes
a no-op when pdata member is the first one in the structure.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210528112127.71738-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dev_dbg() in any case prints the device and driver name, no need
to repeat this in (some) messages. Drop duplicates for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210528112127.71738-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As of commit 4cdc2ec1da ("mmc: dw_mmc: move rockchip related code
to a separate file"), dw_mmc-pltfm.c no longer uses the clock API.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210527194226.1705607-1-geert@linux-m68k.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hardware provides capability configuration registers for each SDHCI
in the global configuration space for the SD controller. Writes to the
global capability registers are mirrored to the capability registers in
the associated SDHCI. Configuration of the capabilities must be written
through the mirror registers prior to initialisation of the SDHCI.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210524073308.9328-5-steven_lee@aspeedtech.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the SET_ROM_WAIT_STATES request which erroneously used
usb_rcvctrlpipe().
Fixes: 88095e7b47 ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Cc: stable@vger.kernel.org # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210521133026.17296-1-johan@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. this change is just to simplify the code, no
actual functional changes.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1621558965-34077-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. this change is just to simplify the code, no
actual functional changes.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1621558775-31185-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. this change is just to simplify the code, no
actual functional changes
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1621513304-27824-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The same calculation to get transfer descriptor offset is already used
at 3 different locations. Let's create a new helper to simplify code.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210521034432.2321-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We already have 'mrq->data' before calling these two functions, no
need to find it again via 'mrq->data' internally. Also remove local
data variable accordingly.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210517100900.1620-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some boards the data strobe line isn't wired up, rendering HS400
support broken, even if both the controller and the eMMC claim to
support it. Allow to disable HS400 mode via DT.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Link: https://lore.kernel.org/r/20210510190400.105162-3-l.stach@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of having an indirection through the SDHCI layer and emulating
a capability bit, that isn't there in hardware, do the same same thing
as with HS400_ES and advertise the support for HS400 directly through
the MMC caps.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20210510190400.105162-2-l.stach@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In SD spec v6.x the SD function extension registers for performance
enhancements were introduced. As a part of this an optional internal cache
on the SD card, can be used to improve performance.
The let the SD card use the cache, the host needs to enable it and manage
flushing of the cache, so let's add support for this.
Note that for an SD card supporting the cache it's mandatory for it, to
also support the poweroff notification feature. According to the SD spec,
if the cache has been enabled and a poweroff notification is sent to the
card, that implicitly also means that the card should flush its internal
cache. Therefore, dealing with cache flushing for REQ_OP_FLUSH block
requests is sufficient.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210511101359.83521-1-ulf.hansson@linaro.org
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210511093329.4670-1-thunder.leizhen@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Fixes: 75fa9ea6e3 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210508020321.1677-1-thunder.leizhen@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To prepare to add internal cache management for SD cards, let's start by
moving the eMMC specific code into a new ->flush_cache() bus_ops callback.
In this way, it becomes straight forward to add the SD specific parts,
as subsequent changes are about to show.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210506145829.198823-2-ulf.hansson@linaro.org
According to the eMMC Spec:
"When command queuing is enabled (CMDQ Mode En bit in CMDQ_MODE_EN
field is set to ‘1’) class 11 commands are the only method through
which data transfer tasks can be issued. Existing data transfer
commands, namely CMD18/CMD17 and CMD25/CMD24, are not supported when
command queuing is enabled."
which means if CMDQ is enabled, the FFU commands will not be supported.
To fix this issue, just simply disable CMDQ on the ioctl path, and
re-enable CMDQ once ioctl request is completed.
Tested-by: Michael Brunner <Michael.Brunner@kontron.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 1e8e55b670 (mmc: block: Add CQE support)
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210504203209.361597-1-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rather than only deselecting the SD card via a CMD7, before we cut power to
it at system suspend, at runtime suspend or at shutdown, let's add support
for a graceful power off sequence via enabling the SD Power Off
Notification feature.
Note that, the Power Off Notification feature was added in the SD spec
v4.x, which is several years ago. However, it's still a bit unclear how
often the SD card vendors decides to implement support for it. To validate
these changes a Sandisk Extreme PRO A2 64GB has been used, which seems to
work nicely.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210504161222.101536-12-ulf.hansson@linaro.org
In SD spec v6.x the SD function extension registers for performance
enhancements were introduced. These registers let the SD card announce
supports for various performance related features, like "self-maintenance",
"cache" and "command queuing".
Let's extend the parsing of SD function extension registers and store the
information in the struct mmc_card. This prepares for subsequent changes to
implement the complete support for new the performance enhancement
features.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210504161222.101536-11-ulf.hansson@linaro.org
In the SD spec v4.0 the CMD48/49 and CMD58/59 were introduced as optional
commands. In the SD spec v4.1 the SD function extension registers were
introduced, which requires support for CMD48/49/58/59 to be read/written
from/to.
Moreover, a specific function extension register were added to let the card
announce support for optional features in regards to power management. The
features that were added are "Power Off Notification", "Power Down Mode"
and "Power Sustenance".
As a first step to support this, let's read and parse the register for
power management during the SD card initialization and store the
information about the supported features in the struct mmc_card. In this
way, we prepare for subsequent changes to implement the complete support
for the new features.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-10-ulf.hansson@linaro.org
In SD spec v4.x the support for CMD48/49 and CMD58/59 were introduced as
optional features. To let the card announce whether it supports the
commands, the SCR register has been extended with corresponding support
bits. Let's parse and store this information for later use.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-9-ulf.hansson@linaro.org
The SD_SWITCH (CMD6) is an ADTC type of command with an R1 response, which
can be sent by using the mmc_send_adtc_data(). Let's do that and drop the
open coding in mmc_sd_switch().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-8-ulf.hansson@linaro.org
The function mmc_send_cxd_data() sends a data read command of ADTC type and
prepares to receive an R1 response. To make it even more re-usable, let's
extend it with another in-parameter for the command argument. While at it,
let's also rename the function to mmc_send_adtc_data() as it better
describes its purpose.
Note that, this change doesn't add any new users of the function. Instead
that is done from subsequent changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-7-ulf.hansson@linaro.org
After the eMMC sleep command (CMD5) has been sent, the card start signals
busy on the DAT0 line, which can be monitored to understand when it's
allowed to proceed to power off the VCC regulator.
When MMC_CAP_WAIT_WHILE_BUSY isn't supported by the host the DAT0 line
isn't being monitored for busy completion, but instead we are waiting a
fixed period of time. The time corresponds to the sleep timeout that is
specified in the EXT_CSD register of the eMMC card. This is many cases
suboptimal, as the timeout corresponds to the worst case scenario.
To improve the situation add support for HW busy polling through the
->card_busy() host ops, when the host supports this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-6-ulf.hansson@linaro.org
Via __mmc_poll_for_busy() we end up polling with the ->card_busy() host ops
or by sending the CMD13. To allow polling of different types, which is
needed to support a few new SD card features, let's rework the code around
__mmc_poll_for_busy() to make it more generic.
More precisely, let __mmc_poll_for_busy() take a pointer to a callback
function as in-parameter, which it calls to poll for busy state completion.
Additionally, let's share __mmc_poll_for_busy() to allow it to be re-used
outside of mmc_ops.c. Subsequent changes will make use of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-5-ulf.hansson@linaro.org
To make the code a bit more understandable, let's move the check about
whether polling is allowed or not, out to the caller instead. In this way,
we can also drop the send_status in-parameter, so let's do that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-4-ulf.hansson@linaro.org
In mmc_send_hpi_cmd() the host->max_busy_timeout is being validated towards
the timeout for the eMMC HPI command, as to decide whether an R1 or R1B
response should be used.
Although, it has turned out the some host can't cope with that conversion,
but needs R1B, which means MMC_CAP_NEED_RSP_BUSY is set for them. Let's
take this into account, via using the common mmc_prepare_busy_cmd() when
doing the validation, which also avoids some open coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-3-ulf.hansson@linaro.org
Similar code for validating the host->max_busy_timeout towards the current
command's busy timeout, exists in mmc_do_erase(), mmc_sleep() and
__mmc_switch(). Let's move the common code into a helper function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210504161222.101536-2-ulf.hansson@linaro.org
On the Toshiba Encore 2 WT8-B the microSD slot always reports the card
being write-protected even though microSD cards do not have a write-protect
switch at all.
Add a new DMI_QUIRK_SD_NO_WRITE_PROTECT quirk entry to sdhci-acpi.c's
DMI quirk table for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210503092157.5689-1-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable@vger.kernel.org
disable_irq() after request_irq() still has a time gap in which interrupts
can come. request_irq() with IRQF_NO_AUTOEN flag will disable IRQ
auto-enable because of requesting.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1617765339-28946-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R-Car M3-W ES3.0 is marketed as R-Car M3-W+ (R8A77961), and has its own
compatible value "renesas,r8a77961".
Hence using soc_device_match() with soc_id = "r8a7796" and revision =
"ES3.*" does not actually match running on an R-Car M3-W+ SoC.
Fix this by matching with soc_id = "r8a77961" instead.
Fixes: a38c078fea ("mmc: renesas_sdhi: Avoid bad TAP in HS400")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/ee8af5d631f5331139ffea714539030d97352e93.1622811525.git.geert+renesas@glider.be
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have to bring the eMMC from sending-data state back to transfer state
once we detected a CRC error (timeout) during tuning. So, send a stop
command via mmc_abort_tuning().
Fixes: 4f11997773 ("mmc: tmio: Add tuning support")
Reported-by Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210602073435.5955-1-wsa+renesas@sang-engineering.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Inserting an SD-card on an Intel NUC10i3FNK4 (which contains a GL9755)
results in the message:
mmc0: 1.8V regulator output did not become stable
Following this message, some cards work (sometimes), but most cards fail
with EILSEQ. This behaviour is observed on Debian 10 running kernel
4.19.188, but also with 5.8.18 and 5.11.15.
The driver currently waits 5ms after switching on the 1.8V regulator for
it to become stable. Increasing this to 10ms gets rid of the warning
about stability, but most cards still fail. Increasing it to 20ms gets
some cards working (a 32GB Samsung micro SD works, a 128GB ADATA
doesn't). At 50ms, the ADATA works most of the time, and at 100ms both
cards work reliably.
Signed-off-by: Daniel Beer <dlbeer@gmail.com>
Acked-by: Ben Chuang <benchuanggli@gmail.com>
Fixes: e51df6ce66 ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210424081652.GA16047@nyquist.nev
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The brcmfmac driver can generate a scatterlist from a skb with each packets
not aligned to the block size. This is not supported by the Amlogic Descriptor
dma engine where each descriptor must match a multiple of the block size.
The sg list is valid, since the sum of the sg buffers is a multiple of the
block size, but we must discard those when in SD_IO_RW_EXTENDED mode since
SDIO block mode can be used under the hood even with data->blocks == 1.
Those transfers are very rare, thus can be replaced by a bounce buffer
without real performance loss.
Fixes: 7412dee9f1 ("mmc: meson-gx: replace WARN_ONCE with dev_warn_once about scatterlist size alignment in block mode")
Cc: stable@vger.kernel.org
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210426175559.3110575-2-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some drivers like ath10k can sometimg give an sg buffer with an offset whose alignment
is not compatible with the Amlogic DMA descriptor engine requirements.
Simply replace with dev_warn_once() to inform user this should be fixed to avoid
degraded performance.
This should be ultimately fixed in ath10k, but since it's only a performance issue
the warning should be removed.
Fixes: 79ed05e329 ("mmc: meson-gx: add support for descriptor chain mode")
Cc: stable@vger.kernel.org
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210426175559.3110575-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Fix hanging on I/O during system suspend for removable cards
- Set read only for SD cards with permanent write protect bit
- Power cycle the SD/SDIO card if CMD11 fails for UHS voltage
- Issue a cache flush for eMMC only when it's enabled
- Adopt to updated cache ctrl settings for eMMC from MMC ioctls
- Use use device property API when parsing voltages
- Don't retry eMMC sanitize cmds
- Use the timeout from the MMC ioctl for eMMC santize cmds
MMC host:
- mmc_spi: Make of_mmc_spi.c resource provider agnostic
- mmc_spi: Use polling for card detect even without voltage-ranges
- sdhci: Check for reset prior to DMA address unmap
- sdhci-acpi: Add support for the AMDI0041 eMMC controller variant
- sdhci-esdhc-imx: Depending on OF Kconfig and cleanup code
- sdhci-pci: Add PCI IDs for Intel LKF
- sdhci-pci: Fix initialization of some SD cards for Intel BYT
- sdhci-pci-gli: Various improvements for GL97xx variants
- sdhci-of-dwcmshc: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- sdhci-of-dwcmshc: Add ACPI support for BlueField-3 SoC
- sdhci-of-dwcmshc: Add Rockchip platform support
- tmio/renesas_sdhi: Extend support for reset and use a reset controller
- tmio/renesas_sdhi: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- tmio/renesas_sdhi: Various improvements
MEMSTICK:
- Minor improvements/cleanups.
-----BEGIN PGP SIGNATURE-----
iQJLBAABCgA1FiEEugLDXPmKSktSkQsV/iaEJXNYjCkFAmCJIGkXHHVsZi5oYW5z
c29uQGxpbmFyby5vcmcACgkQ/iaEJXNYjCnX+w//fvTbFsekv/bYZQoiDDGngbg0
LGUfTZPOLWuzHpiQSY5RjRHvt9CFOc07N96RAqxeqgJ3LS2WzIQSn9asK+5EupXH
CVnWKcYBs+1KthMCRsXjduXILztSQFJGbgO8DYrqvwu9mg6SU3ExfqNhX0O+D0ed
GhzQ55yJTitRpa8S2FYQcirl+clV/5+o3uC82nvaoVR1baE1+catNJ028k/Nd0XE
dFboEE6IJ4qndLWAyBnijYMXbLq/HKmqjeNsR5tooAA/QcXf9tQKqHtdim1N1Cac
THF3hGHMskw7bM4PoupzeJYHzYmL6UINkw192BLMNsGCHidflWTarjUR/5Y2OEz1
eKG5GX+Ww+fdsupN8h448rI1h3EcKJlQFvit9/OIcHS8r7ZeouWNXElH3WUpc3i4
pb3yHBBNMQ3rn0wUfjZh2sggyy+/pRAY1OPfeDud1wggRjg/xVMY3nxpqQmFRKZM
C2/mPUMxaY7zHb9AzCOYCjhgjTPh4HrzIRZeqnZ1FRGuv0yLDG46hc1ufLggCx5P
v1RGB2vJ2hGyWIqvBXw1nF8RwiOCXYXPyZjehWU0K6zryGQPq275/6ziFvL+Nh4U
8liwwHeeIQNvPs7HNzSQ1rXo8elNRvWkqZpvCqTWgJCX4/NFYQTj+Lq2T2EiTxWt
dlr9RLlARJEeutA07rM=
=WL87
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC and MEMSTICK updates from Ulf Hansson:
"MMC core:
- Fix hanging on I/O during system suspend for removable cards
- Set read only for SD cards with permanent write protect bit
- Power cycle the SD/SDIO card if CMD11 fails for UHS voltage
- Issue a cache flush for eMMC only when it's enabled
- Adopt to updated cache ctrl settings for eMMC from MMC ioctls
- Use use device property API when parsing voltages
- Don't retry eMMC sanitize cmds
- Use the timeout from the MMC ioctl for eMMC santize cmds
MMC host:
- mmc_spi: Make of_mmc_spi.c resource provider agnostic
- mmc_spi: Use polling for card detect even without voltage-ranges
- sdhci: Check for reset prior to DMA address unmap
- sdhci-acpi: Add support for the AMDI0041 eMMC controller variant
- sdhci-esdhc-imx: Depending on OF Kconfig and cleanup code
- sdhci-pci: Add PCI IDs for Intel LKF
- sdhci-pci: Fix initialization of some SD cards for Intel BYT
- sdhci-pci-gli: Various improvements for GL97xx variants
- sdhci-of-dwcmshc: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- sdhci-of-dwcmshc: Add ACPI support for BlueField-3 SoC
- sdhci-of-dwcmshc: Add Rockchip platform support
- tmio/renesas_sdhi: Extend support for reset and use a reset controller
- tmio/renesas_sdhi: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- tmio/renesas_sdhi: Various improvements
MEMSTICK:
- Minor improvements/cleanups"
* tag 'mmc-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (79 commits)
mmc: block: Issue a cache flush only when it's enabled
memstick: r592: ignore kfifo_out() return code again
mmc: block: Update ext_csd.cache_ctrl if it was written
mmc: mmc_spi: Make of_mmc_spi.c resource provider agnostic
mmc: mmc_spi: Use already parsed IRQ
mmc: mmc_spi: Drop unused NO_IRQ definition
mmc: mmc_spi: Set up polling even if voltage-ranges is not present
mmc: core: Convert mmc_of_parse_voltage() to use device property API
mmc: core: Correct descriptions in mmc_of_parse()
mmc: dw_mmc-rockchip: Just set default sample value for legacy mode
mmc: sdhci-s3c: constify uses of driver/match data
mmc: sdhci-s3c: correct kerneldoc of sdhci_s3c_drv_data
mmc: sdhci-s3c: simplify getting of_device_id match data
mmc: tmio: always restore irq register
mmc: sdhci-pci-gli: Enlarge ASPM L1 entry delay of GL975x
mmc: core: Let eMMC sanitize not retry in case of timeout/failure
mmc: core: Add a retries parameter to __mmc_switch function
memstick: r592: remove unused variable
mmc: sdhci-st: Remove unnecessary error log
mmc: sdhci-msm: Remove unnecessary error log
...
- Add idle states table for IceLake-D to the intel_idle driver and
update IceLake-X C6 data in it (Artem Bityutskiy).
- Fix the C7 idle state on Tegra114 in the tegra cpuidle driver and
drop the unused do_idle() firmware call from it (Dmitry Osipenko).
- Fix cpuidle-qcom-spm Kconfig entry (He Ying).
- Fix handling of possible negative tick_nohz_get_next_hrtimer()
return values of in cpuidle governors (Rafael Wysocki).
- Add support for frequency-invariance to the ACPI CPPC cpufreq
driver and update the frequency-invariance engine (FIE) to use it
as needed (Viresh Kumar).
- Simplify the default delay_us setting in the ACPI CPPC cpufreq
driver (Tom Saeger).
- Clean up frequency-related computations in the intel_pstate
cpufreq driver (Rafael Wysocki).
- Fix TBG parent setting for load levels in the armada-37xx
cpufreq driver and drop the CPU PM clock .set_parent method for
armada-37xx (Marek Behún).
- Fix multiple issues in the armada-37xx cpufreq driver (Pali Rohár).
- Fix handling of dev_pm_opp_of_cpumask_add_table() return values
in cpufreq-dt to take the -EPROBE_DEFER one into acconut as
appropriate (Quanyang Wang).
- Fix format string in ia64-acpi-cpufreq (Sergei Trofimovich).
- Drop the unused for_each_policy() macro from cpufreq (Shaokun
Zhang).
- Simplify computations in the schedutil cpufreq governor to avoid
unnecessary overhead (Yue Hu).
- Fix typos in the s5pv210 cpufreq driver (Bhaskar Chowdhury).
- Fix cpufreq documentation links in Kconfig (Alexander Monakov).
- Fix PCI device power state handling in pci_enable_device_flags()
to avoid issuse in some cases when the device depends on an ACPI
power resource (Rafael Wysocki).
- Add missing documentation of pm_runtime_resume_and_get() (Alan
Stern).
- Add missing static inline stub for pm_runtime_has_no_callbacks()
to pm_runtime.h and drop the unused try_to_freeze_nowarn()
definition (YueHaibing).
- Drop duplicate struct device declaration from pm.h and fix a
structure type declaration in intel_rapl.h (Wan Jiabing).
- Use dev_set_name() instead of an open-coded equivalent of it in
the wakeup sources code and drop a redundant local variable
initialization from it (Andy Shevchenko, Colin Ian King).
- Use crc32 instead of md5 for e820 memory map integrity check
during resume from hibernation on x86 (Chris von Recklinghausen).
- Fix typos in comments in the system-wide and hibernation support
code (Lu Jialin).
- Modify the generic power domains (genpd) code to avoid resuming
devices in the "prepare" phase of system-wide suspend and
hibernation (Ulf Hansson).
- Add Hygon Fam18h RAPL support to the intel_rapl power capping
driver (Pu Wen).
- Add MAINTAINERS entry for the dynamic thermal power management
(DTPM) code (Daniel Lezcano).
- Add devm variants of operating performance points (OPP) API
functions and switch over some users of the OPP framework to
the new resource-managed API (Yangtao Li and Dmitry Osipenko).
- Update devfreq core:
* Register devfreq devices as cooling devices on demand (Daniel
Lezcano).
* Add missing unlock opeation in devfreq_add_device() (Lukasz
Luba).
* Use the next frequency as resume_freq instead of the previous
frequency when using the opp-suspend property (Dong Aisheng).
* Check get_dev_status in devfreq_update_stats() (Dong Aisheng).
* Fix set_freq path for the userspace governor in Kconfig (Dong
Aisheng).
* Remove invalid description of get_target_freq() (Dong Aisheng).
- Update devfreq drivers:
* imx8m-ddrc: Remove imx8m_ddrc_get_dev_status() and unneeded
of_match_ptr() (Dong Aisheng, Fabio Estevam).
* rk3399_dmc: dt-bindings: Add rockchip,pmu phandle and drop
references to undefined symbols (Enric Balletbo i Serra, Gaël
PORTAY).
* rk3399_dmc: Use dev_err_probe() to simplify the code (Krzysztof
Kozlowski).
* imx-bus: Remove unneeded of_match_ptr() (Fabio Estevam).
- Fix kernel-doc warnings in three places (Pierre-Louis Bossart).
- Fix typo in the pm-graph utility code (Ricardo Ribalda).
-----BEGIN PGP SIGNATURE-----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=t+SG
-----END PGP SIGNATURE-----
Merge tag 'pm-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add some new hardware support (for example, IceLake-D idle
states in intel_idle), fix some issues (for example, the handling of
negative "sleep length" values in cpuidle governors), add new
functionality to the existing drivers (for example, scale-invariance
support in the ACPI CPPC cpufreq driver) and clean up code all over.
Specifics:
- Add idle states table for IceLake-D to the intel_idle driver and
update IceLake-X C6 data in it (Artem Bityutskiy).
- Fix the C7 idle state on Tegra114 in the tegra cpuidle driver and
drop the unused do_idle() firmware call from it (Dmitry Osipenko).
- Fix cpuidle-qcom-spm Kconfig entry (He Ying).
- Fix handling of possible negative tick_nohz_get_next_hrtimer()
return values of in cpuidle governors (Rafael Wysocki).
- Add support for frequency-invariance to the ACPI CPPC cpufreq
driver and update the frequency-invariance engine (FIE) to use it
as needed (Viresh Kumar).
- Simplify the default delay_us setting in the ACPI CPPC cpufreq
driver (Tom Saeger).
- Clean up frequency-related computations in the intel_pstate cpufreq
driver (Rafael Wysocki).
- Fix TBG parent setting for load levels in the armada-37xx cpufreq
driver and drop the CPU PM clock .set_parent method for armada-37xx
(Marek Behún).
- Fix multiple issues in the armada-37xx cpufreq driver (Pali Rohár).
- Fix handling of dev_pm_opp_of_cpumask_add_table() return values in
cpufreq-dt to take the -EPROBE_DEFER one into acconut as
appropriate (Quanyang Wang).
- Fix format string in ia64-acpi-cpufreq (Sergei Trofimovich).
- Drop the unused for_each_policy() macro from cpufreq (Shaokun
Zhang).
- Simplify computations in the schedutil cpufreq governor to avoid
unnecessary overhead (Yue Hu).
- Fix typos in the s5pv210 cpufreq driver (Bhaskar Chowdhury).
- Fix cpufreq documentation links in Kconfig (Alexander Monakov).
- Fix PCI device power state handling in pci_enable_device_flags() to
avoid issuse in some cases when the device depends on an ACPI power
resource (Rafael Wysocki).
- Add missing documentation of pm_runtime_resume_and_get() (Alan
Stern).
- Add missing static inline stub for pm_runtime_has_no_callbacks() to
pm_runtime.h and drop the unused try_to_freeze_nowarn() definition
(YueHaibing).
- Drop duplicate struct device declaration from pm.h and fix a
structure type declaration in intel_rapl.h (Wan Jiabing).
- Use dev_set_name() instead of an open-coded equivalent of it in the
wakeup sources code and drop a redundant local variable
initialization from it (Andy Shevchenko, Colin Ian King).
- Use crc32 instead of md5 for e820 memory map integrity check during
resume from hibernation on x86 (Chris von Recklinghausen).
- Fix typos in comments in the system-wide and hibernation support
code (Lu Jialin).
- Modify the generic power domains (genpd) code to avoid resuming
devices in the "prepare" phase of system-wide suspend and
hibernation (Ulf Hansson).
- Add Hygon Fam18h RAPL support to the intel_rapl power capping
driver (Pu Wen).
- Add MAINTAINERS entry for the dynamic thermal power management
(DTPM) code (Daniel Lezcano).
- Add devm variants of operating performance points (OPP) API
functions and switch over some users of the OPP framework to the
new resource-managed API (Yangtao Li and Dmitry Osipenko).
- Update devfreq core:
* Register devfreq devices as cooling devices on demand (Daniel
Lezcano).
* Add missing unlock opeation in devfreq_add_device() (Lukasz
Luba).
* Use the next frequency as resume_freq instead of the previous
frequency when using the opp-suspend property (Dong Aisheng).
* Check get_dev_status in devfreq_update_stats() (Dong Aisheng).
* Fix set_freq path for the userspace governor in Kconfig (Dong
Aisheng).
* Remove invalid description of get_target_freq() (Dong Aisheng).
- Update devfreq drivers:
* imx8m-ddrc: Remove imx8m_ddrc_get_dev_status() and unneeded
of_match_ptr() (Dong Aisheng, Fabio Estevam).
* rk3399_dmc: dt-bindings: Add rockchip,pmu phandle and drop
references to undefined symbols (Enric Balletbo i Serra, Gaël
PORTAY).
* rk3399_dmc: Use dev_err_probe() to simplify the code (Krzysztof
Kozlowski).
* imx-bus: Remove unneeded of_match_ptr() (Fabio Estevam).
- Fix kernel-doc warnings in three places (Pierre-Louis Bossart).
- Fix typo in the pm-graph utility code (Ricardo Ribalda)"
* tag 'pm-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
PM: wakeup: remove redundant assignment to variable retval
PM: hibernate: x86: Use crc32 instead of md5 for hibernation e820 integrity check
cpufreq: Kconfig: fix documentation links
PM: wakeup: use dev_set_name() directly
PM: runtime: Add documentation for pm_runtime_resume_and_get()
cpufreq: intel_pstate: Simplify intel_pstate_update_perf_limits()
cpufreq: armada-37xx: Fix module unloading
cpufreq: armada-37xx: Remove cur_frequency variable
cpufreq: armada-37xx: Fix determining base CPU frequency
cpufreq: armada-37xx: Fix driver cleanup when registration failed
clk: mvebu: armada-37xx-periph: Fix workaround for switching from L1 to L0
clk: mvebu: armada-37xx-periph: Fix switching CPU freq from 250 Mhz to 1 GHz
cpufreq: armada-37xx: Fix the AVS value for load L1
clk: mvebu: armada-37xx-periph: remove .set_parent method for CPU PM clock
cpufreq: armada-37xx: Fix setting TBG parent for load levels
cpuidle: Fix ARM_QCOM_SPM_CPUIDLE configuration
cpuidle: tegra: Remove do_idle firmware call
cpuidle: tegra: Fix C7 idling state on Tegra114
PM: sleep: fix typos in comments
cpufreq: Remove unused for_each_policy macro
...
In command queueing mode, the cache isn't flushed via the mmc_flush_cache()
function, but instead by issuing a CMDQ_TASK_MGMT (CMD48) with a
FLUSH_CACHE opcode. In this path, we need to check if cache has been
enabled, before deciding to flush the cache, along the lines of what's
being done in mmc_flush_cache().
To fix this problem, let's add a new bus ops callback ->cache_enabled() and
implement it for the mmc bus type. In this way, the mmc block device driver
can call it to know whether cache flushing should be done.
Fixes: 1e8e55b670 (mmc: block: Add CQE support)
Cc: stable@vger.kernel.org
Reported-by: Brendan Peter <bpeter@lytx.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Tested-by: Brendan Peter <bpeter@lytx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210425060207.2591-2-avri.altman@wdc.com
Link: https://lore.kernel.org/r/20210425060207.2591-3-avri.altman@wdc.com
[Ulf: Squashed the two patches and made some minor updates]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
