Fix the following warnings from dtc by adding the unit name to memory
nodes:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Converted using the following command:
perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`
The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
UDOO board has a possibility to disable most of imx6 SoC power supplies via
"EN_5V" signal, which is connected to "NANDF_D4" pad.
This reduces current consumption after shutdown from ~350 mA to ~40 mA and
prevents a SoC watchdog from starting it again on its own after the
watchdog timeout expires (previously it was not possible to shut down the
SoC permanently if its watchdog was ever enabled since it was still ticking
after the shutdown).
Unfortunately, this does not extinguish the "Power" LED (as it is powered
from an always-on voltage regulator).
To power the SoC up again press the power button (SW2, the one with a long
shaft).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
AC'97 interface RXD and TXC pins are only used as SoC inputs, let's disable
pad drivers for them so we will be protected if, for example, TCLKDIR is
set by mistake in AUDMUX and causes TXC pin to be configured as an output.
This also changes pull direction on these pins from pull-up to pull-down
to match what the board AC'97 CODEC chip (VT1613) has on these pins.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Several dts files set a bit in the SPEED field for pads
RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there
doesn't have an effect and the bit reads as zero.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using "IMX6QDL_CLK_CKO" for the clock is easier to read instead of
the hardcoded clock number.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The official UDOO board kit has 7 and 15.6 inch touchscreen LCD panels
as options.
This patch adds support for 7 inch panel only, but the 15.6 inch one
should be easy to add using the same regulator, backlight device and
LVDS channel.
Since this panel is an option for UDOO board it is disabled by default
and can be enabled (for example) by the following U-Boot commands:
fdt set backlight status okay
fdt set panelchan status okay
fdt set panel7 status okay
fdt set touchscreenp7 status okay
The LVDS channels is also disabled by default to avoid warning from its
driver.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add sound support in UDOO board DT file.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For more information about the Udoo boards:
http://www.udoo.org/
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
