SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clearing of mrq via a memset at the top of the for loop in
mmc_wait_for_app_cmd() is not required as mrq is not used and there is
another clearing of mrq just below. We remove the first memset since if
the initial tests in the for loop fail the memset is not required.
Signed-off-by: Mark Asselstine <asselsm@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Teach the MMC/SD/SDIO core about using SPI mode.
- Use mmc_host_is_spi() so enumeration works through SPI signaling
and protocols, not just the native versions.
- Provide the SPI response type flags with each request issued,
including requests from the new lock/unlock code.
- Understand that cmd->resp[0] and mmc_get_status() results for SPI
return different values than for "native" MMC/SD protocol; this
affects resetting, checking card lock status, and some others.
- Understand that some commands act a bit differently ... notably:
* OP_COND command doesn't return the OCR
* APP_CMD status doesn't have an R1_APP_CMD analogue
Those changes required some new and updated primitives:
- Provide utilities to access two SPI-only requests, and one
request that wasn't previously needed:
* mmc_spi_read_ocr() ... SPI only
* mmc_spi_set_crc() ... SPI only (override by module parm)
* mmc_send_cid() ... for use without broadcast mode
- Updated internal routines:
* Previous mmc_send_csd() modified into mmc_send_cxd_native();
it uses native "R2" responses, which include 16 bytes of data.
* Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
helper for command-and-data access
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
- Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper
- Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
those helper routines based on whether they're native or SPI
The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The write parameter in mmc_set_data_timeout() is redundant as the
data structure contains information about the direction of the
transfer.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch makes the following needlessly global functions static:
- sd_ops.c: mmc_app_cmd()
- core.c: __mmc_release_bus()
- core.c: mmc_start_request()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Move protocol operations and definitions into their own files
in an effort to separate protocol handling and bus
arbitration more clearly.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
