The last user of mmc_power_save|restore_host() APIs is gone, hence let's
drop them. Drop also the corresponding bus_ops callback,
->power_save|restore() as those becomes redundant.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Eyal Reizer <eyalreizer@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R1_STATUS(x) now is only used by ioctl_rpmb_card_status_poll(),
which checks all bits as possible. But according to the spec,
bit 17 and bit 18 should be ignored, as well bit 14 which is
reserved(must be set to 0) quoting from the spec and these rule
apply to all places checking the device status. So change
its checking from 0xFFFFE000 to 0xFFF9A000.
As a bonus, we reuse it for mmc_do_erase() as well as
mmc_switch_status_error().
(1) Currently mmc_switch_status_error() doesn't check bit 25, but
it means device is locked but not unlocked by CMD42 prior to any
operations which need check busy, which is also not allowed.
(2) mmc_do_erase() also forgot to to check bit 15, WP_ERASE_SKIP.
The spec says "Only partial address space was erased due to existing
write protected blocks.", which obviously means we should fail this I/O.
Otherwise, the partial erased data stored in nonvalatile flash violates
the data integrity from the view of I/O owner, which probably confuse
it when further used.
So reusing R1_STATUS for them not only improve the readability but also
slove real problems.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This drastically reduces the rate at which the MMC_SEND_STATUS cmd polls
for completion of the MMC Erase operation. The patch does this by adding
a backoff sleep that starts by sleeping for short intervals (128-256us),
and ramps up to sleeping for 32-64ms.
Even on very quickly completing erase operations, the loop iterates a few
times, so not too much extra latency is added to these commands.
For long running discard operarations, like a full-device secure discard,
this change drops the interrupt rates on my single-core NXP I.MX6UL from
45000/s to about 20/s, and greatly improves system responsiveness.
Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hard-coded 10ms delay in mmc_power_up came from
commit 79bccc5aef ("mmc: increase power up delay"), which said "The TI
controller on Toshiba Tecra M5 needs more time to power up or the cards
will init incorrectly or not at all." But it's too engineering solution
for a special board but force all platforms to wait for that long time,
especially painful for mmc_power_up for eMMC when booting.
However, it's added since 2009, and we can't tell if other platforms
benefit from it. But in practise, the modern hardware are most likely to
have a stable power supply with 1ms after setting it for no matter PMIC
or discrete power. And more importnatly, most regulators implement the
callback of ->set_voltage_time_sel() for regulator core to wait for
specific period of time for the power supply to be stable, which means
once regulator_set_voltage_* return, the power should reach the the
minimum voltage that works for initialization. Of course, if there
are some other ways for host to power the card, we should allow them
to argue a suitable delay as well.
With this patch, we could assign the delay from firmware, or we could
assigne it via ->set_ios() callback from host drivers.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the corresponding code for setting the initial signal voltage, from
mmc_power_up() into a new function, mmc_set_initial_signal_voltage().
Make the function internally available to the mmc core, as to allow the
following changes to make use of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
It's rather common that a firmware is loaded into an SDIO func device
memory, by the corresponding SDIO func driver during ->probe() time.
However, to actually start running the new firmware, sometimes a soft reset
(no power cycle) and a re-initialization of the card is needed. This is for
example the case with the Espressif ESP8089 WiFi chips, when connected to
an SDIO interface.
To cope with this scenario, let's add a new exported function,
mmc_sw_reset(), which may be called when a soft reset and re-initialization
of the card are needed.
The mmc_sw_reset() is implemented on top of a new bus ops callback, similar
to how the mmc_hw_reset() has been implemented.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The bus ops ->reset() executes a full HW reset of the card, as the calling
function mmc_hw_reset() also indicates by its name. Let's convert to follow
the similar names, for both the bus ops callback and for the corresponding
bus ops functions, as to clarify the purpose of code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Commit 03dbaa04a2 ("mmc: slot-gpio: Add support to enable irq wake on
cd_irq") enabled wakeup at initialization. However drivers may wish to
enable and disable based on different criteria. Add a helper function
mmc_gpio_set_cd_wake() to make it easy for drivers to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the max_discard value is zero, the conditional branch that checks the
trim capabilities will never update this value with max_trim.
Change the condition statement to also check the max_discard value in order
to avoid an unnecessary call to mmc_do_calc_max_discard.
Signed-off-by: Sergio Valverde <vlvrdv@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Weibu F3C MiniPC has an onboard AP6255 module, presenting
two SDIO functions on a single MMC host (Bluetooth/btsdio and
WiFi/brcmfmac), and the mmc layer correctly detects this as
non-removable.
After suspend/resume, the wifi and bluetooth interfaces disappear
and do not get probed again.
The conditions here are:
1. During suspend, we reach mmc_pm_notify()
2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can
suspend the SDIO host. However, mmc_sdio_pre_suspend() returns
-ENOSYS because btsdio_driver does not have a suspend method.
3. mmc_pm_notify() proceeds to remove the card
4. Upon resume, mmc_rescan() does nothing with this host, because of
the rescan_entered check which aims to only scan a non-removable
device a single time (i.e. during boot).
Fix the loss of functionality by detecting that we are unable to
suspend a non-removable host, so avoid the forced removal in that
case. The comment above this function already indicates that this
code was only intended for removable devices.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove config option MMC_MQ_DEFAULT and parameter mmc_use_blk_mq, so that
blk-mq must be used always.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_test now uses mmc_start_request() to test sending commands during
"ongoing" asynchronous transfers, i.e. tests:
Commands during non-blocking read - use Set Block Count (CMD23)
Commands during non-blocking write - use Set Block Count (CMD23)
mmc_start_request() was not initializing cmd_completion, but cmd_completion
is used by "ongoing" transfers, so move initialization of cmd_completion
into making mmc_start_request().
Fixes: cb39f61e9b ("mmc: core: Export a few functions needed for blkmq support")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Until mmc has blk-mq support fully implemented and tested, add a parameter
use_blk_mq, set to true if config option MMC_MQ_DEFAULT is selected, which
it is by default.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Make mmc_pre_req() and mmc_post_req() available to the card drivers. Later
patches will make use of this.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Especially, make clear what the return value means.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out mmc_host_set_uhs_voltage() so it can be reused.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following functions are needed by the mmc block device driver, once it
converts to blkmq, therefore let's export them.
mmc_start_bkops()
mmc_start_request()
mmc_retune_hold_now()
mmc_retune_release()
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add core support for handling CQE requests, including starting, completing
and recovering.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the host can be claimed by a task. Change this so that the host
can be claimed by a context that may or may not be a task. This provides
for the host to be claimed by a block driver queue to support blk-mq, while
maintaining compatibility with the existing use of mmc_claim_host().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CQE needs to be off for the host controller to accept non-CQ commands. Turn
off the CQE before sending commands, and ensure it is off in any reset or
power management paths, or re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the SD physical layer simplified specification V4.10,
section 4.6.2, CSD version 1.0 SD card should use taac, nsac
and r2w_factor for calculating the data access time. But the
taac and nsac for SDHC(CSD version 2.0) are always fixed and
the software should use the recommended value for timeout. When
parsing the CSD, we sanely set them to zero for SDHC(CSD version
2.0), all the calculation for timeout_ns and timeout_clk is zero
as well. So what we actually want to limit here is either SDHC
case or unreasonable timeout reported by the cards. In principle
we should at least be able to remove the bogus check for the
mmc_card_blockaddr.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the spec of JESD84-B51, section 7.3, replace tacc with taac to
fix the obvious typo.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Jan Glauber <jglauber@cavium.com>
Cc: David Daney <david.daney@cavium.com>
Cc: "Steven J. Hill" <Steven.Hill@cavium.com>
Cc: linux-mmc@vger.kernel.org
Acked-by: David Daney <david.daney@cavium.com>
Tested-by: Steven J. Hill <Steven.Hill@cavium.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are lots of debug message in core.c which use pr_debug
for better dynamic log level control. So it doesn't make sense
for those print to still keep working only under CONFIG_MMC_DEBUG.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the check within mmc_mrq_prep seems to be all-or-none
proposition, so it doesn't make sense to only check the
length of sglist only under the CONFIG_MMC_DEBUG context.
I'd prefer to always keep the check there unconditionally.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intention of this check was to prevent the conflict between
hotplug and removing driver for whatever reason. Currently it
doesn't improve anything and the following rescan process could
still saftly perform the scan flow. So these code seems pointless
now and let's remove them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add host capability MMC_CAP_CD_WAKE to enable irq wake on the card detect
irq.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_flush_cache() is a eMMC specific function, let's move it to
mmc_ops.c to make that clear.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_interrupt_hpi() is a eMMC specific function, let's move it to
mmc_ops.c to make that clear. The move also enables us to make
mmc_send_hpi_cmd() static, so let's do that change as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_start_bkops(), mmc_stop_bkops() and mmc_read_bkops_status()
functions are all specific to eMMCs. To make this clear, let's move them
from from core.c to mmc_ops.c and take the opportunity to make
mmc_read_bkops_status() static.
While moving them, get rid of MMC_BKOPS_MAX_TIMEOUT (4 min) and use the
common default timeout MMC_OPS_TIMEOUT_MS (10 min) instead, as there is no
need to have specific default timeout for bkops.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_start|stop_bkops(), mmc_read_bkops_status() and mmc_interrupt_hpi()
functions are all used from within the mmc core module, thus there are no
need to use EXPORT_SYMBOL() for them, so let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
In case if a pwrseq-emmc has been bound to the host, a call to
mmc_power_up() triggers an eMMC HW reset via the pwrseq_emmc's
->post_power_on() callback. This isn't really what we want, as
mmc_power_up() is called each time when resuming the card.
As a matter of fact, the current approach may also violate the eMMC spec,
as the involved delays managed in pwrseq_emmc assumes both VCC and VCCQ has
been turned on, which isn't the case for VCCQ, unless the regulator is
always on.
Fix this behaviour by aligning to the same procedure used when the mmc host
implements the ->hw_reset() callback and has the MMC_CAP_HW_RESET flag set.
In this way the eMMC HW reset is issued at card detection scan, to cope
with bogus bootloaders and in the error recovery path via the mmc specific
bus_ops->reset() callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Some hosts controllers, like Cavium, needs to know whether the card
operates in byte- or block-address mode. Therefore export a new API,
mmc_card_is_blockaddr(), which provides this information.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Steven J. Hill <Steven.Hill@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
The host may issue an I/O abort by writing to the CCCR at any time
during I/O read operation via CMD52. And host may need suspend
transcation during write busy stage in SDIO suspend/resume scenario.
>From other side, a card may accept CMD52 during data transfer phase.
Previous implement would block issuing above command in busy stage.
It cause function driver can't implement as proper way and has no
opportunity to do some coverage in error case via I/O abort etc.
We need bypass some necessary operation during busy check stage.
Signed-off-by: Jiajie Hao <jiajie.hao@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have this construction:
if (a && b && !c)
finalize;
else
block;
finalize;
Which is equivalent by boolean logic to:
if (!a || !b || c)
block;
finalize;
Which is simpler code.
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_wait_for_data_req_done() is called in exactly one place,
and having it spread out is making things hard to oversee.
Factor this function into mmc_finalize_areq().
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"previous" is a better name for the variable storing the previous
asynchronous request, better than the opaque name "data" atleast.
We see that we assign the return status to the returned variable
on all code paths, so we might as well just do that immediately
after calling mmc_finalize_areq().
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to reuse the code for CQE support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to reuse the code for CQE support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This function is doing to many clever things at the same time under
too many various conditions.
Start to make things clearer by refactoring: break out the
finalization of the previous asynchronous request to its own
function mmc_finalize_areq(). We can get rid of the default
assignment of status and let the call deal with this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With the coexisting __mmc_start_request(), mmc_start_request()
and __mmc_start_req() it is a bit confusing that mmc_start_req()
actually does not start a normal request, but an asynchronous
request.
Rename it to mmc_start_areq() to make it explicit what the
function is doing, also fix the kerneldoc for this function
while we're at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 64b12a68a9
"mmc: core: fix prepared requests while doing bkops"
is fixing a bug in the wrong way. A bug in the MMCI
device driver is fixed by amending the MMC core.
Thinking about it: what the pre- and post-callbacks
are doing is to essentially map and unmap SG lists
for DMA transfers. Why would we not be able to do that
just because a BKOPS command is sent inbetween?
Having to unprepare/prepare the next asynchronous
request for DMA seems wrong.
Looking the backtrace in that commit we can see what
the real problem actually is:
mmci_data_irq() is calling mmci_dma_unmap() twice
which is goung to call arm_dma_unmap_sg() twice
and v7_dma_inv_range() twice for the same sglist
and that will crash.
This happens because a request is prepared, then
a BKOPS is sent. The IRQ completing the BKOPS command
goes through mmci_data_irq() and thinks that a DMA
operation has just been completed because
dma_inprogress() reports true. It then proceeds to
unmap the sglist.
But that was wrong! dma_inprogress() should NOT be
true because no DMA was actually in progress! We had
just prepared the sglist, and the DMA channel
dma_current has been configured, but NOT started!
Because of this, the sglist is already unmapped when
we get our actual data completion IRQ, and we are
unmapping the sglist once more, and we get this crash.
Therefore, we need to revert this solution pushing
the problem to the core and causing problems, and
instead augment the implementation such that
dma_inprogress() only reports true if some DMA has
actually been started.
After this we can keep the request prepared during the
BKOPS and we need not unprepare/reprepare it.
Fixes: 64b12a68a9 ("mmc: core: fix prepared requests while doing bkops")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Earlier the mmc_set_signal_voltage() existed, but since it has been renamed
to mmc_set_uhs_voltage(), we can now use that name instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
The mmc_set_signal_voltage() function is used for SD/SDIO when switching to
1.8V for UHS mode. To clarify this let's do the following changes.
- We are always providing MMC_SIGNAL_VOLTAGE_180 as the signal_voltage
parameter to the function. Then, let's just remove the parameter as it
serves no purpose.
- Rename the function to mmc_set_uhs_voltage().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
The mmc_set_signal_voltage() function is used for SD/SDIO when switching to
1.8V for UHS mode. Therefore let's remove the redundant code dealing with
MMC_SIGNAL_VOLTAGE_330.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
A significant amount of functions and other definitions are available
through the public mmc card.h header file. Let's slim down this public mmc
interface, as to prevent users from abusing it, by moving some of the
functions/definitions to private mmc header files.
This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
In the MMC subsystem, we see such initializers that only clears the
first member explicitly.
For example,
struct mmc_request mrq = {NULL};
sets the first member (.sbc) to NULL explicitly. However, this is
an unstable form because we may insert a non-pointer member at the
top of the struct mmc_request in the future. (if we do so, the
compiler will spit warnings.)
So, using a designated initializer is preferred coding style. The
expression above is equivalent to:
struct mmc_request mrq = { .sbc = NULL };
Of course, this does not express our intention. We want to fill
all struct members with zeros. Please note struct members are
implicitly zero-cleared unless otherwise specified in the initializer.
After all, the most reasonable (and stable) form is:
struct mmc_request mrq = {};
Do likewise for mmc_command, mmc_data as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e0097cf5f2 ("mmc: queue: Fix queue thread wake-up") did not go far
enough. mmc_wait_for_data_req_done() still contains some problems and can
be further simplified. First it should not touch
context_info->is_waiting_last_req because that is a wake-up control used by
the owner of the context. Secondly, it should always return when one of its
wake-up conditions is met because, again, that is contolled by the owner of
the context.
While the current block driver does not have an issue, these problems were
exposed during testing of the Software Command Queue patches.
Fixes: e0097cf5f2 ("mmc: queue: Fix queue thread wake-up")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Harjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
