* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl3KwQYACgkQJWrqGEe9
VoTj1wf/Zvnk1u2vNVUaWDaHnUTAcMvjYNr1N1ppXquRXQTknZHxcgqavcwOA3yV
inHRdjQpvTPft3Pb0tddC2VBOMQTYWDGJs6JOLiPF5c4QdW/w4yHRrdnEIumbVP/
itXySbPj2QsXcRuIoEm165NTI8mdSzZFixZvCNS58r2mvMXvQbcUHsP9vjlUs9/S
XPqBlSBPKa6hC2ToIiXhgkGDQzVJ/OkCOSgG+37ATUrEqWUi9oN2KUPkbk4HSZe9
dntUIFSjeAqGjKGRGwAlt4axhnFWABfWa9xBwX9k5s4mt/FJ9QF24geemz/F1Ljp
7xd6MJu3JYoW8qBcXRRDgHuv5RNnHA==
=rpUJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.5' into mtd/next
Raw NAND core
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl3Kep8ACgkQS1VPR6WN
FOn9kgf/aKPgU6LR84YpwUKRZ4S+6K1H8SdDUt8v0FYSQ6oaTjF13fApg43WDja5
Zk0l5tlX7WIvlcRC6XKPhryZTXOKWojW1X8sguPYIZGzo7q82Eyda23jkw1QptWr
VO9L/tdK4yVUbdtp6VS/FUF31PC0DtDoCzsfBSUgrZP2srFF1BtOJNUgyuDceoxo
y3hEmINDnkaOvDDl/kbJjdEHG4PV8Vi4k0KE8deLpqlp8GDG1nkTeA1Sim7WjBPA
ZZOdg9fmGI8H8+umQEnn06H4O95T2+fX+kDMCYo4RbgWyWlGv5TidgRREmC/cSbl
YEPu6LCQoUZPVEvgolr/8Akf968ZiQ==
=i15M
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.5' into mtd/next
SPI NOR core changes:
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
* Code cleanups related useless initializers and coding style issues
* Fix for a possible double free problem in cfi_cmdset_0002
* Improved error reporting and handling in cfi_cmdset_0002 core for HyperFlash
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAl3GhtAQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW4/0NB/9LJZ7CQKjQOBpxypJ9LzFcXF7KHF+xaU4G
NRDJTeAng7c034tFj2tHfsICs1epidMC7OOdKZq+AJuN3M6Iq2JtqKb19r3pfQyo
S2HGQaHwrH3K8iF8ba5MBtax0xncipQgQgIAPgWZ80MdJWZKLh1F5hqhDyrO/LBR
vYG4TLmOJk5Chro5PtRytOQV/i+1VfSS7R7zleTDtCGH3pMbFOU9ySac1pDQfNmR
b36RRt119Vs6V80Sb+3L8AFfYCIcNwFySmzWJGPgmrdruTRUIeQ3II6M2HSMEYbO
oUTzxFDOTuBGrBLa3Rsq0Z9OhZk1WQqOC1f6mmfjRz/FdqiJBTXs
=K6bc
-----END PGP SIGNATURE-----
Merge CFI/Hyperbus tag 'for-v5.5-rc1' into mtd/next
CFI core changes:
* Code cleanups related useless initializers and coding style issues
* Fix for a possible double free problem in cfi_cmdset_0002
* Improved error reporting and handling in cfi_cmdset_0002 core for HyperFlash
Due to the use of sizeof(), command size set for the spi transfer
was wrong. Driver was sending and receiving always 1 byte less
and especially on write, it was hanging.
echo -n -e "\\x1\\x2\\x3\\x4" > /dev/mtd1
And read part too now works as expected.
hexdump -C -n16 /dev/mtd1
00000000 01 02 03 04 ab f3 ad c2 ab e3 f4 36 dd 38 04 15
00000010
Fixes: 4379075a87 ("mtd: mchp23k256: Add support for mchp23lcv1024")
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Set the default Quad Enable method for ISSI flashes. Used for
ISSI flashes (IS25WP256D-JMLE) that do not support SFDP tables
and can not determine the Quad Enable method by parsing BFPT.
Based on code originally written by Wesley Terpstra <wesley@sifive.com>
and/or Palmer Dabbelt <palmer@sifive.com>
c94e267766
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
[tudor.ambarus@microchip.com:
- rebase, split and adapt for latest spi-nor/next,
- use PMC CFI ID for ISSI. According to JEP106BA, "Programmable Micro Corp"
changed its name to Integrated Silicon Solution (ISSI)]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Update the spi_nor_id table for is25wp256 (32MB) device from ISSI,
present on HiFive Unleashed dev board (Rev: A00).
Use the post bfpt fixup hook for the is25wp256 device, as done for
the is25lp256 device to overwrite the wrong address width advertised
by BFPT.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
[tudor.ambarus@microchip.com: rebase, split and adapt for latest spi-nor/next]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Add MTD support for w25q256jw SPI NOR chip from Winbond. This chip
supports dual/quad I/O mode with 512 blocks of memory organized in
64KB sectors. In addition to this, there is also small 4KB sectors
available for flexibility. The device has been validated using Thor96
board.
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Darshak Patel <darshak.patel@einfochips.com>
[Mani: cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When the controller is not under the SPI-MEM interface it may implement
the optional controller_ops->erase() method.
nor->spimem and nor->controller_ops are mutually exclusive. Move the
nor->controller_ops->erase != NULL check as an 'else if' case to
nor->spimem, in order to avoid the nor->controller_ops != NULL
check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Expand the spi_nor_check() to make sure that nor->spimem and
nor->controller_ops are mutually exclusive.
Fixes: b35b9a1036 ("mtd: spi-nor: Move m25p80 code in spi-nor.c")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Rename macronix_quad_enable() to a generic name:
spi_nor_sr1_bit6_quad_enable().
Prepend "spi_nor_" to "sr2_bit7_quad_enable". All SPI NOR generic
methods should be prepended by "spi_nor_".
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Merge
spansion_no_read_cr_quad_enable()
spansion_read_cr_quad_enable()
into
spi_nor_sr2_bit1_quad_enable().
Reduce code duplication by introducing spi_nor_write_16bit_cr_and_check().
The Configuration Register contains bits that can be updated in future:
FREEZE, CMP. Provide a generic method that allows updating all bits
of the Configuration Register.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
JEDEC Basic Flash Parameter Table, 15th DWORD, bits 22:20,
refers to this bit as "bit 1 of the status register 2".
Rename the macro accordingly.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Test that all the bits from Status Register 1 and Status Register 2
were written correctly.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
spi_nor_unlock() unlocks blocks of memory or the entire flash memory
array, if requested. clear_sr_bp() unlocks the entire flash memory
array at boot time. This calls for some unification, clear_sr_bp() is
just an optimization for the case when the unlock request covers the
entire flash size.
Get rid of clear_sr_bp() and introduce spi_nor_unlock_all(), which is
just a call to spi_nor_unlock() for the entire flash memory array.
This fixes a bug that was present in spi_nor_spansion_clear_sr_bp().
When the QE bit was zero, we used the Write Status (01h) command with
one data byte, which might cleared the Status Register 2. We now always
use the Write Status (01h) command with two data bytes when
SNOR_F_HAS_16BIT_SR is set, to avoid clearing the Status Register 2.
The SNOR_F_NO_READ_CR case is treated as well. When the flash doesn't
support the CR Read command, we make an assumption about the value of
the QE bit. In spi_nor_init(), call spi_nor_quad_enable() first, then
spi_nor_unlock_all(), so that at the spi_nor_unlock_all() time we can
be sure the QE bit has value one, because of the previous call to
spi_nor_quad_enable().
Get rid of the MFR handling and implement specific manufacturer
default_init() fixup hooks.
Note that this changes a bit the logic for the SNOR_MFR_ATMEL,
SNOR_MFR_INTEL and SNOR_MFR_SST cases. Before this patch, the Atmel,
Intel and SST chips did not set the locking ops, but unlocked the entire
flash at boot time, while now they are setting the locking ops to
stm_locking_ops. This should work, since the disable of the block
protection at the boot time used the same Status Register bits to unlock
the flash, as in the stm_locking_ops case.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Make sure that when doing a lock() or an unlock() operation we don't clear
the QE bit from Status Register 2.
JESD216 revB or later offers information about the *default* Status
Register commands to use (see BFPT DWORDS[15], bits 22:20). In this
standard, Status Register 1 refers to the first data byte transferred on a
Read Status (05h) or Write Status (01h) command. Status register 2 refers
to the byte read using instruction 35h. Status register 2 is the second
byte transferred in a Write Status (01h) command.
Industry naming and definitions of these Status Registers may differ.
The definitions are described in JESD216B, BFPT DWORDS[15], bits 22:20.
There are cases in which writing only one byte to the Status Register 1
has the side-effect of clearing Status Register 2 and implicitly the Quad
Enable bit. This side-effect is hit just by the
BFPT_DWORD15_QER_SR2_BIT1_BUGGY and BFPT_DWORD15_QER_SR2_BIT1 cases.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
The commit 4844ef8030 ("mtd: cfi_cmdset_0002: Add support for polling
status register") added checking for the status register error bits into
chip_good() to only return 1 if these bits are 0s. Unfortunately, this
means that polling using chip_good() always reaches a timeout condition
when erase or program failure bits are set. Let's fully delegate the task
of determining the error conditions to cfi_check_err_status() and make
chip_good() only look for the Device Ready/Busy condition.
Fixes: 4844ef8030 ("mtd: cfi_cmdset_0002: Add support for polling status register")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Cypress S26K{L|S}P{128|256|512}S datasheet says that the error bits in
the status register are only valid when the "device ready" bit 7 is set.
Add the check for the device ready bit in cfi_check_err_status() as that
function isn't always called with this bit set.
Fixes: 4844ef8030 ("mtd: cfi_cmdset_0002: Add support for polling status register")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Else there may be a double-free problem, because cfi->cfiq will
be freed by mtd_do_chip_probe() if both the two invocations of
check_cmd_set() return failure.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The 'ret' local variables are typically initialized to 0 but this value is
often unused, thus we can kill those initializers.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Use DIV_ROUND_UP() in cfi_udelay() instead of open-coding it...
Doing this also helpfully gets rid of two complaints from
'scripts/checkpatch.pl --strict':
CHECK: spaces preferred around that '+' (ctx:VxV)
#29: FILE: drivers/mtd/chips/cfi_util.c:29:
+ msleep((us+999)/1000);
^
CHECK: spaces preferred around that '/' (ctx:VxV)
#29: FILE: drivers/mtd/chips/cfi_util.c:29:
+ msleep((us+999)/1000);
^
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Check that all the bits written in the write_sr_and_check() method
match the status_new received value. Failing to write the other bits
is dangerous too, extend the check.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
When the Read-Modify-Write-Read-Back Quad Enable methods failed on
the Read-Back, they returned -EINVAL. Since this is an I/O error,
return -EIO.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Drop the default spansion_quad_enable() method and replace it with
spansion_read_cr_quad_enable().
The function was buggy, it didn't care about the previous values
of the Status and Configuration Registers. spansion_read_cr_quad_enable()
is a Read-Modify-Write-Check function that keeps track of what were
the previous values of the Status and Configuration Registers.
In terms of instruction types sent to the flash, the only difference
between the spansion_quad_enable() and spansion_read_cr_quad_enable()
is that the later calls spi_nor_read_sr(). We can safely assume that all
flashes support spi_nor_read_sr(), because all flashes call it in
spi_nor_sr_ready(). The transition from spansion_quad_enable() to
spansion_read_cr_quad_enable() will not affect anybody, drop the buggy
code.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Merge
static int spi_nor_write_sr(struct spi_nor *nor, u8 val)
static int spi_nor_write_sr_cr(struct spi_nor *nor, const u8 *sr_cr)
into
static int spi_nor_write_sr(struct spi_nor *nor, const u8 *sr, size_t len)
The Status Register can be written with one or two bytes. Merge
the two functions to avoid code duplication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Avoid duplicating code by moving the calls to spi_nor_write_enable() and
spi_nor_wait_till_ready() inside the Write Status Register methods.
Move spi_nor_write_sr() to avoid forward declaration of
spi_nor_wait_till_ready().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
spi_nor_clear_sr() and spi_nor_clear_fsr() are called just in case
of errors. The callers didn't check their return value, make them
of type void.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Rename 'sst_write_err' label to 'out' as it is no longer generic for
all the errors in the sst_write() method, and may introduce confusion.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Check for the return vales of each Register Operation.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
What most users care about is "my dev is not working properly".
All low level information should be discovered when activating
the debug traces.
Keep error messages just for the following cases:
- when the SR/FSR report program or erase fails, or attempts of
modifying a protected sector,
- when the JEDEC ID is not recognized,
- when the resume() call fails,
- when the spi_nor_check() fails.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
spi_nor_read_raw() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.
Fixes: f384b352cb ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
spi_nor_read() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.
Fixes: 59451e1233 ("mtd: spi-nor: change return value of read/write")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Comet Lake-H PCH has the same SPI serial flash controller as Comet
Lake-LP. Add Comet Lake-H PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Print identifying information about struct device.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Constify the data to write to the Status Register.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
In case the write of the first byte failed, retlen was incorrectly
incremented to *retlen += actual; on the exit path. retlen should be
incremented when actual data was written to the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Drop the error messages from the callers, since the callees
already print an error message in case of failure.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Configuration Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Callers stop compare the return value of spi_nor_read_cr() with negative,
spi_nor_read_cr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Flag Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Caller stops compare the return value of spi_nor_read_fsr() with negative,
spi_nor_read_fsr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Callers stop compare the return value of spi_nor_read_sr() with negative,
spi_nor_read_sr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Do not overwrite the error numbers received the Register Operations
methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
spi_mem_exec_op()
nor->controller_ops->write_reg()
nor->controller_ops->read_reg()
spi_nor_wait_till_ready()
Return 0 on success, -errno otherwise.
Stop compare with negative and compare with zero in all the register
operations methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Group all register methods up in the file, to avoid forward
declarations.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Two new lines, one after another, drop one.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
All the core functions should begin with "spi_nor_".
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Remove unecessary checking if dmac is NULL.
If Cadence nand controller driver uses DMA engine then cdns_ctrl->dmac
cannot be NULL. It is verified during driver initialization.
If Cadence nand controller driver does not use DMA engine then
CPU IO read/write are executed instead of slave DMA transfer.
In that case cdns_ctrl->dmac is not used at all.
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
