A kernel page fault oops with the callstack below was observed
when a read syscall was made to a pmem device after a huge amount
(>512GB) of vmalloc ranges was allocated by ioremap() on a x86_64
system:
BUG: unable to handle kernel paging request at ffff880840000ff8
IP: vmalloc_fault+0x1be/0x300
PGD c7f03a067 PUD 0
Oops: 0000 [#1] SM
Call Trace:
__do_page_fault+0x285/0x3e0
do_page_fault+0x2f/0x80
? put_prev_entity+0x35/0x7a0
page_fault+0x28/0x30
? memcpy_erms+0x6/0x10
? schedule+0x35/0x80
? pmem_rw_bytes+0x6a/0x190 [nd_pmem]
? schedule_timeout+0x183/0x240
btt_log_read+0x63/0x140 [nd_btt]
:
? __symbol_put+0x60/0x60
? kernel_read+0x50/0x80
SyS_finit_module+0xb9/0xf0
entry_SYSCALL_64_fastpath+0x1a/0xa4
Since v4.1, ioremap() supports large page (pud/pmd) mappings in
x86_64 and PAE. vmalloc_fault() however assumes that the vmalloc
range is limited to pte mappings.
vmalloc faults do not normally happen in ioremap'd ranges since
ioremap() sets up the kernel page tables, which are shared by
user processes. pgd_ctor() sets the kernel's PGD entries to
user's during fork(). When allocation of the vmalloc ranges
crosses a 512GB boundary, ioremap() allocates a new pud table
and updates the kernel PGD entry to point it. If user process's
PGD entry does not have this update yet, a read/write syscall
to the range will cause a vmalloc fault, which hits the Oops
above as it does not handle a large page properly.
Following changes are made to vmalloc_fault().
64-bit:
- No change for the PGD sync operation as it handles large
pages already.
- Add pud_huge() and pmd_huge() to the validation code to
handle large pages.
- Change pud_page_vaddr() to pud_pfn() since an ioremap range
is not directly mapped (while the if-statement still works
with a bogus addr).
- Change pmd_page() to pmd_pfn() since an ioremap range is not
backed by struct page (while the if-statement still works
with a bogus addr).
32-bit:
- No change for the sync operation since the index3 PGD entry
covers the entire vmalloc range, which is always valid.
(A separate change to sync PGD entry is necessary if this
memory layout is changed regardless of the page size.)
- Add pmd_huge() to the validation code to handle large pages.
This is for completeness since vmalloc_fault() won't happen
in ioremap'd ranges as its PGD entry is always valid.
Reported-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: <stable@vger.kernel.org> # 4.1+
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: linux-mm@kvack.org
Cc: linux-nvdimm@lists.01.org
Link: http://lkml.kernel.org/r/1455758214-24623-1-git-send-email-toshi.kani@hpe.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Looks like the HPET spec at intel.com got moved.
It isn't hard to find so drop the link, just mention
the revision assumed.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-doc@vger.kernel.org
Link: http://lkml.kernel.org/r/1455145462-3877-1-git-send-email-mst@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Data corruption issues were observed in tests which initiated
a system crash/reset while accessing BTT devices. This problem
is reproducible.
The BTT driver calls pmem_rw_bytes() to update data in pmem
devices. This interface calls __copy_user_nocache(), which
uses non-temporal stores so that the stores to pmem are
persistent.
__copy_user_nocache() uses non-temporal stores when a request
size is 8 bytes or larger (and is aligned by 8 bytes). The
BTT driver updates the BTT map table, which entry size is
4 bytes. Therefore, updates to the map table entries remain
cached, and are not written to pmem after a crash.
Change __copy_user_nocache() to use non-temporal store when
a request size is 4 bytes. The change extends the current
byte-copy path for a less-than-8-bytes request, and does not
add any overhead to the regular path.
Reported-and-tested-by: Micah Parrish <micah.parrish@hpe.com>
Reported-and-tested-by: Brian Boylston <brian.boylston@hpe.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: <stable@vger.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: linux-nvdimm@lists.01.org
Link: http://lkml.kernel.org/r/1455225857-12039-3-git-send-email-toshi.kani@hpe.com
[ Small readability edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull irqchip fixes from Thomas Gleixner:
"Another set of ARM SoC related irqchip fixes:
- Plug a memory leak in gicv3-its
- Limit features to the root gic interrupt controller
- Add a missing barrier in the gic-v3 IAR access
- Another compile test fix for sun4i"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Make sure read from ICC_IAR1_EL1 is visible on redestributor
irqchip/gic: Only set the EOImodeNS bit for the root controller
irqchip/gic: Only populate set_affinity for the root controller
irqchip/gicv3-its: Fix memory leak in its_free_tables()
irqchip/sun4i: Fix compilation outside of arch/arm
Pull x86 fixes from Thomas Gleixner:
"Two small fixlets for x86:
- Prevent a KASAN false positive in thread_saved_pc()
- Fix a 32-bit truncation problem in the x86 numa code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/numa: Fix 32-bit memblock range truncation bug on 32-bit NUMA kernels
x86: Fix KASAN false positives in thread_saved_pc()
Pull MIPS fixes from Ralf Baechle:
"Here's the first round of MIPS fixes after the merge window:
- Detect Octeon III's PCI correctly.
- Fix return value of the MT7620 probing function.
- Wire up the copy_file_range syscall.
- Fix 64k page support on 32 bit kernels.
- Fix the early Coherency Manager probe.
- Allow only hardware-supported page sizes to be selected for R6000.
- Fix corner cases for the RDHWR nstruction emulation on old hardware.
- Fix FPU handling corner cases.
- Remove stale entry for BCM33xx from the MAINTAINERS file.
- 32 and 64 bit ELF headers are different, handle them correctly"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
mips: Differentiate between 32 and 64 bit ELF header
MIPS: Octeon: Update OCTEON_FEATURE_PCIE for Octeon III
MIPS: pci-mt7620: Fix return value check in mt7620_pci_probe()
MIPS: Fix early CM probing
MIPS: Wire up copy_file_range syscall.
MIPS: Fix 64k page support for 32 bit kernels.
MIPS: R6000: Don't allow 64k pages for R6000.
MIPS: traps.c: Correct microMIPS RDHWR emulation
MIPS: traps.c: Don't emulate RDHWR in the CpU #0 exception handler
MAINTAINERS: Remove stale entry for BCM33xx chips
MIPS: Fix FPU disable with preemption
MIPS: Properly disable FPU in start_thread()
MIPS: Fix buffer overflow in syscall_get_arguments()
Pull ARM fixes from Russell King:
"A couple of ARM fixes from Linus for the ICST clock generator code"
[ "Linus" here is Linus Walleij. Name-stealer.
Linus "there can be only one" Torvalds ]
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8519/1: ICST: try other dividends than 1
ARM: 8517/1: ICST: avoid arithmetic overflow in icst_hz()
- Corner case of returning to delay slot from interrupt
- Changing default interrupt prioiry level
- Kconfig'ize support for super pages
- Other minor fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FNDd
-----END PGP SIGNATURE-----
Merge tag 'arc-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"I've been sitting on some of these fixes for a while.
- Corner case of returning to delay slot from interrupt
- Changing default interrupt prioiry level
- Kconfig'ize support for super pages
- Other minor fixes"
* tag 'arc-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: Introduce explicit super page size support
ARCv2: intc: Allow interruption by lowest priority interrupt
ARCv2: Check for LL-SC livelock only if LLSC is enabled
ARC: shrink cpuinfo by not saving full timer BCR
ARCv2: clocksource: Rename GRTC -> GFRC ...
ARCv2: STAR 9000950267: Handle return from intr to Delay Slot #2
Merge fixes from Andrew Morton:
"10 fixes"
The lockdep hlist conversion is in the locking tree too, waiting for the
next merge window. Andrew thought it should go in now. I'll take it,
since it fixes a real problem and looks trivially correct (famous last
words).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
arch/x86/Kconfig: CONFIG_X86_UV should depend on CONFIG_EFI
mm: fix pfn_t vs highmem
kernel/locking/lockdep.c: convert hash tables to hlists
mm,thp: fix spellos in describing __HAVE_ARCH_FLUSH_PMD_TLB_RANGE
mm,thp: khugepaged: call pte flush at the time of collapse
mm/backing-dev.c: fix error path in wb_init()
mm, dax: check for pmd_none() after split_huge_pmd()
vsprintf: kptr_restrict is okay in IRQ when 2
mm: fix filemap.c kernel doc warning
ubsan: cosmetic fix to Kconfig text
* fix omap2plus_defconfig to enable omapfb as it was in v4.4
* ocfb: fix timings for margins
* s6e8ax0, da8xx-fb: fix compile warnings
* mmp: fix build failure caused by bad printk parameters
* imxfb: fix clock issue which kept the display off
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kfw6
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- fix omap2plus_defconfig to enable omapfb as it was in v4.4
- ocfb: fix timings for margins
- s6e8ax0, da8xx-fb: fix compile warnings
- mmp: fix build failure caused by bad printk parameters
- imxfb: fix clock issue which kept the display off
* tag 'fbdev-fixes-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: fbdev: imxfb: Provide a reset mechanism
fbdev: mmp: print IRQ resource using %pR format string
fbdev: da8xx-fb: remove incorrect type cast
fbdev: s6e8ax0: avoid unused function warnings
ocfb: fix tgdel and tvdel timing parameters
ARM: omap2plus_defconfig: update display configs
MMUv4 supports 2 concurrent page sizes: Normal and Super [4K to 16M]
So far Linux supported a single super page size for a given Normal page,
depending on the software page walking address split.
e.g. we had 11:8:13 address split for 8K page, which meant super page
was 2 ^(8+13) = 2M (given that THP size has to be PMD_SHIFT)
Now we turn this around, by allowing multiple Super Pages in Kconfig
(currently 2M and 16M only) and forcing page walker address split to
PGDIR_SHIFT and PAGE_SHIFT
For configs without Super page, things are same as before and
PGDIR_SHIFT can be hacked to get non default address split
The motivation for this change is a customer who needs 16M super page
and a 8K Normal page combo.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
arch/x86/built-in.o: In function `uv_bios_call':
(.text+0xeba00): undefined reference to `efi_call'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Suggested-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Alex Thorlton <athorlton@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the dawn of time the ICST code has only supported divide
by one or hang in an eternal loop. Luckily we were always dividing
by one because the reference frequency for the systems using
the ICSTs is 24MHz and the [min,max] values for the PLL input
if [10,320] MHz for ICST307 and [6,200] for ICST525, so the loop
will always terminate immediately without assigning any divisor
for the reference frequency.
But for the code to make sense, let's insert the missing i++
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Depending on the configuration either the 32 or 64 bit version of
elf_check_arch() is defined. parse_crash_elf{32|64}_headers() does
some basic verification of the ELF header via
vmcore_elf{32|64}_check_arch() which happen to map to elf_check_arch().
Since the implementation 32 and 64 bit version of elf_check_arch()
differ, we use the wrong type:
In file included from include/linux/elf.h:4:0,
from fs/proc/vmcore.c:13:
fs/proc/vmcore.c: In function 'parse_crash_elf64_headers':
>> arch/mips/include/asm/elf.h:228:23: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
struct elfhdr *__h = (hdr); \
^
include/linux/crash_dump.h:41:37: note: in expansion of macro 'elf_check_arch'
#define vmcore_elf64_check_arch(x) (elf_check_arch(x) || vmcore_elf_check_arch_cross(x))
^
fs/proc/vmcore.c:1015:4: note: in expansion of macro 'vmcore_elf64_check_arch'
!vmcore_elf64_check_arch(&ehdr) ||
^
Therefore, we rather define vmcore_elf{32|64}_check_arch() as a
basic machine check and use it also in binfm_elf?32.c as well.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Suggested-by: Maciej W. Rozycki <macro@imgtec.com>
Reviewed-by: Maciej W. Rozycki <macro@imgtec.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12529/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ARM GICv3 specification mentions the need for dsb after a read
from the ICC_IAR1_EL1 register:
4.1.1 Physical CPU Interface:
The effects of reading ICC_IAR0_EL1 and ICC_IAR1_EL1
on the state of a returned INTID are not guaranteed
to be visible until after the execution of a DSB.
Not having this could result in missed interrupts, so let's add the
required barrier.
[Marc: fixed commit message]
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In case of error, the function devm_ioremap_resource() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12451/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
ARC HS Cores support configurable multiple interrupt priorities of upto
16 levels.
There is processor "interrupt preemption threshhold" in STATUS32.E[4:1]
And several places need to set this up:
1. seed value as kernel is booting
2. seed value for user space programs
3. Arg to SLEEP instruction in idle task (what interrupt prio can wake)
4. Per-IRQ line prioirty (i.e. what is the priority of interrupt
raised by a peripheral or timer or perf counter...
Currently above sites use the highest priority 0. This can be potential
problem when multiple priorities are supported. e.g. user space could
only be interrupted by P0 interrupt, not others...
So turn this over and instead make default interruption level to be
the lowest priority possible 15. This should be fine even if there are
fewer priority levels configured (say two: P0 HIGH, P1 LOW)
This feature also effectively disables FIRQ feature if present in
hardware config. With old code, a P0 interrupt would be FIRQ, needing
special handling (ISR or Register Banks) which is NOT supported yet.
Now it not be P0 (P15 or whatever is lowest prio) so FIRQ is not
triggered.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Commit c014d164f2 ("MIPS: Add platform callback before initializing
the L2 cache") added a platform_early_l2_init function in order to allow
platforms to probe for the CM before L2 initialisation is performed, so
that CM GCRs are available to mips_sc_probe.
That commit actually fails to do anything useful, since it checks
mips_cm_revision to determine whether it should call mips_cm_probe but
the result of mips_cm_revision will always be 0 until mips_cm_probe has
been called. Thus the "early" mips_cm_probe call never occurs.
Fix this & drop the useless weak platform_early_l2_init function by
simply calling mips_cm_probe from setup_arch. For platforms that don't
select CONFIG_MIPS_CM this will be a no-op, and for those that do it
removes the requirement for them to call mips_cm_probe manually
(although doing so isn't harmful for now).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12475/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 29bb45f25f (regmap-mmio: Use native endianness for read/write)
attempted to fix some long standing bugs in the MMIO implementation for
big endian systems caused by duplicate byte swapping in both regmap and
readl()/writel() which affected MIPS systems as when they are in big
endian mode they flip the endianness of all registers in the system, not
just the CPU. MIPS systems had worked around this by declaring regmap
using IPs as little endian which is inaccurate, unfortunately the issue
had not been reported.
Sadly the fix makes things worse rather than better. By changing the
behaviour to match the documentation it caused behaviour changes for
other IPs which broke them and by using the __raw I/O accessors to avoid
the endianness swapping in readl()/writel() it removed some memory
ordering guarantees and could potentially generate unvirtualisable
instructions on some architectures.
Unfortunately sorting out all this mess in any half way sensible fashion
was far too invasive to go in during an -rc cycle so instead let's go
back to the old broken behaviour for v4.5, the better fixes are already
queued for v4.6. This does mean that we keep the broken MIPS DTs for
another release but that seems the least bad way of handling the
situation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWtIjbAAoJECTWi3JdVIfQs8QH/jNpfio4klDkdlH/KpPZXlrp
FzASbGePNtLqZXFL5WcG//ni3EYdbaiXZIdLBKDx9K4F2ca9FAF8aAnZAZ5uefGx
bnloYpV34DqQwS5f9FrrNsm+YVTTuUIt0dx4ZRGCEdMTzW7i3efs/9eVEITUixK6
U1obTJovAl33bihadsC9hzJVwfOq3H4aFFWc/EFZzbQaU2/so2eiA1dhPr/YErRJ
dMR8drWxpYXuBsrk5T647R0sUw7pA4Zw+WAF032TPQf/1Fy9Vk1/yXbTyccZzFzo
bfupRA/HpeLNZ9cN9z9y3Fa0je4UNbBZh0poB5B773af84NnhX7Ytenjo+peVxI=
=+Q6E
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-v4.5-big-endian' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"A single revert back to v4.4 endianness handling.
Commit 29bb45f25f ("regmap-mmio: Use native endianness for
read/write") attempted to fix some long standing bugs in the MMIO
implementation for big endian systems caused by duplicate byte
swapping in both regmap and readl()/writel(). Sadly the fix makes
things worse rather than better, so revert it for now"
* tag 'regmap-fix-v4.5-big-endian' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: mmio: Revert to v4.4 endianness handling
When trying to set the ICST 307 clock to 25174000 Hz I ran into
this arithmetic error: the icst_hz_to_vco() correctly figure out
DIVIDE=2, RDW=100 and VDW=99 yielding a frequency of
25174000 Hz out of the VCO. (I replicated the icst_hz() function
in a spreadsheet to verify this.)
However, when I called icst_hz() on these VCO settings it would
instead return 4122709 Hz. This causes an error in the common
clock driver for ICST as the common clock framework will call
.round_rate() on the clock which will utilize icst_hz_to_vco()
followed by icst_hz() suggesting the erroneous frequency, and
then the clock gets set to this.
The error did not manifest in the old clock framework since
this high frequency was only used by the CLCD, which calls
clk_set_rate() without first calling clk_round_rate() and since
the old clock framework would not call clk_round_rate() before
setting the frequency, the correct values propagated into
the VCO.
After some experimenting I figured out that it was due to a simple
arithmetic overflow: the divisor for 24Mhz reference frequency
as reference becomes 24000000*2*(99+8)=0x132212400 and the "1"
in bit 32 overflows and is lost.
But introducing an explicit 64-by-32 bit do_div() and casting
the divisor into (u64) we get the right frequency back, and the
right frequency gets set.
Tested on the ARM Versatile.
Cc: stable@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A few random fixes, mostly coming from the PMU work by Shannon:
- fix for injecting faults coming from the guest's userspace
- cleanup for our CPTR_EL2 accessors (reserved bits)
- fix for a bug impacting perf (user/kernel discrimination)
- fix for a 32bit sysreg handling bug
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=36kx
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/ARM fixes for v4.5-rc2
A few random fixes, mostly coming from the PMU work by Shannon:
- fix for injecting faults coming from the guest's userspace
- cleanup for our CPTR_EL2 accessors (reserved bits)
- fix for a bug impacting perf (user/kernel discrimination)
- fix for a 32bit sysreg handling bug
The following commit:
a0acda9172 ("acpi, numa, mem_hotplug: mark all nodes the kernel resides un-hotpluggable")
Introduced numa_clear_kernel_node_hotplug(), which function is executed
during early bootup, and which marks all currently reserved memblock
regions as hot-memory-unswappable as well.
y14sg1 <y14sg1@comcast.net> reported that when running 32-bit NUMA kernels,
the grsecurity/PAX kernel patch flagged a size overflow in this function:
PAX: size overflow detected in function x86_numa_init arch/x86/mm/numa.c:691 [...]
... the reason for the overflow is that memblock_clear_hotplug() takes physical
addresses as arguments, while the start/end variables used by
numa_clear_kernel_node_hotplug() are 'unsigned long', which is 32-bit on PAE
kernels, but which has 64-bit physical addresses.
So on 32-bit PAE kernels that have physical memory above the 4GB boundary,
we truncate a 64-bit physical address range to 32 bits and pass it to
memblock_clear_hotplug(), which at minimum prevents the original memory-hotplug
bugfix from working, but might have other side effects as well.
The fix is to use the proper type to handle physical addresses, phys_addr_t.
Reported-by: y14sg1 <y14sg1@comcast.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Chen Tang <imtangchen@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: PaX Team <pageexec@freemail.hu>
Cc: Taku Izumi <izumi.taku@jp.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The first real batch of fixes for this release cycle, so there are a few more
than usual.
Most of these are fixes and tweaks to board support (DT bugfixes, etc). I've
also picked up a couple of small cleanups that seemed innocent enough that
there was little reason to wait (const/__initconst and Kconfig deps).
Quite a bit of the changes on OMAP were due to fixes to no longer write to
rodata from assembly when ARM_KERNMEM_PERMS was enabled, but there were also
other fixes.
Kirkwood had a bunch of gpio fixes for some boards. OMAP had RTC fixes
on OMAP5, and Nomadik had changes to MMC parameters in DT.
All in all, mostly the usual mix of various fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1iBu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"The first real batch of fixes for this release cycle, so there are a
few more than usual.
Most of these are fixes and tweaks to board support (DT bugfixes,
etc). I've also picked up a couple of small cleanups that seemed
innocent enough that there was little reason to wait (const/
__initconst and Kconfig deps).
Quite a bit of the changes on OMAP were due to fixes to no longer
write to rodata from assembly when ARM_KERNMEM_PERMS was enabled, but
there were also other fixes.
Kirkwood had a bunch of gpio fixes for some boards. OMAP had RTC
fixes on OMAP5, and Nomadik had changes to MMC parameters in DT.
All in all, mostly the usual mix of various fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
ARM: multi_v7_defconfig: enable DW_WATCHDOG
ARM: nomadik: fix up SD/MMC DT settings
ARM64: tegra: Add chosen node for tegra132 norrin
ARM: realview: use "depends on" instead of "if" after prompt
ARM: tango: use "depends on" instead of "if" after prompt
ARM: tango: use const and __initconst for smp_operations
ARM: realview: use const and __initconst for smp_operations
bus: uniphier-system-bus: revive tristate prompt
arm64: dts: Add missing DMA Abort interrupt to Juno
bus: vexpress-config: Add missing of_node_put
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
...
Commit 16da306849 ("um: kill pfn_t") introduced a compile warning for
defconfig (SUBARCH=i386):
arch/um/kernel/skas/mmu.c:38:206:
warning: right shift count >= width of type [-Wshift-count-overflow]
Aforementioned patch changes the definition of the phys_to_pfn() macro
from
((pfn_t) ((p) >> PAGE_SHIFT))
to
((p) >> PAGE_SHIFT)
This effectively changes the phys_to_pfn() expansion's type from
unsigned long long to unsigned long.
Through the callchain init_stub_pte() => mk_pte(), the expansion of
phys_to_pfn() is (indirectly) fed into the 'phys' argument of the
pte_set_val(pte, phys, prot) macro, eventually leading to
(pte).pte_high = (phys) >> 32;
This results in the warning from above.
Since UML only deals with 32 bit addresses, the upper 32 bits from
'phys' used to be always zero anyway. Also, all page protection flags
defined by UML don't use any bits beyond bit 9. Since the contents of a
PTE are defined within architecture scope only, the ->pte_high member
can be safely removed.
Remove the ->pte_high member from struct pte_t.
Rename ->pte_low to ->pte.
Adapt the pte helper macros in arch/um/include/asm/page.h.
Noteworthy is the pte_copy() macro where a smp_wmb() gets dropped. This
write barrier doesn't seem to be paired with any read barrier though and
thus, was useless anyway.
Fixes: 16da306849 ("um: kill pfn_t")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 944d9fec8d ("hugetlb: add support for gigantic page allocation
at runtime") has added the runtime gigantic page allocation via
alloc_contig_range(), making this support available only when CONFIG_CMA
is enabled. Because it doesn't depend on MIGRATE_CMA pageblocks and the
associated infrastructure, it is possible with few simple adjustments to
require only CONFIG_MEMORY_ISOLATION instead of full CONFIG_CMA.
After this patch, alloc_contig_range() and related functions are
available and used for gigantic pages with just CONFIG_MEMORY_ISOLATION
enabled. Note CONFIG_CMA selects CONFIG_MEMORY_ISOLATION. This allows
supporting runtime gigantic pages without the CMA-specific checks in
page allocator fastpaths.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the randconfig build failed with the error:
arch/m32r/kernel/smp.c: In function 'smp_flush_tlb_mm':
arch/m32r/kernel/smp.c:283:20: error: subscripted value is neither array nor pointer nor vector
mmc = &mm->context[cpu_id];
^
arch/m32r/kernel/smp.c: In function 'smp_flush_tlb_page':
arch/m32r/kernel/smp.c:353:20: error: subscripted value is neither array nor pointer nor vector
mmc = &mm->context[cpu_id];
^
arch/m32r/kernel/smp.c: In function 'smp_invalidate_interrupt':
arch/m32r/kernel/smp.c:479:41: error: subscripted value is neither array nor pointer nor vector
unsigned long *mmc = &flush_mm->context[cpu_id];
It turned out that CONFIG_SMP was defined but CONFIG_MMU was not
defined. But arch/m32r/include/asm/mmu.h only defines mm_context_t as
an array when both CONFIG_SMP and CONFIG_MMU are defined. And
arch/m32r/kernel/smp.c is always using context as an array. So without
MMU SMP can not work.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 29bb45f25f (regmap-mmio: Use native endianness for read/write)
attempted to fix some long standing bugs in the MMIO implementation for
big endian systems caused by duplicate byte swapping in both regmap and
readl()/writel() which affected MIPS systems as when they are in big
endian mode they flip the endianness of all registers in the system, not
just the CPU. MIPS systems had worked around this by declaring regmap
using IPs as little endian which is inaccurate, unfortunately the issue
had not been reported.
Sadly the fix makes things worse rather than better. By changing the
behaviour to match the documentation it caused behaviour changes for
other IPs which broke them and by using the __raw I/O accessors to avoid
the endianness swapping in readl()/writel() it removed some memory
ordering guarantees and could potentially generate unvirtualisable
instructions on some architectures.
Unfortunately sorting out all this mess in any half way sensible fashion
was far too invasive to go in during an -rc cycle so instead let's go
back to the old broken behaviour for v4.5, the better fixes are already
queued for v4.6. This does mean that we keep the broken MIPS DTs for
another release but that seems the least bad way of handling the
situation.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
thread_saved_pc() reads stack of a potentially running task.
This can cause false KASAN stack-out-of-bounds reports,
because the running task concurrently poisons and unpoisons
own stack.
The same happens in get_wchan(), and get get_wchan() was fixed
by using READ_ONCE_NOCHECK(). Do the same here.
Example KASAN report triggered by sysrq-t:
BUG: KASAN: out-of-bounds in sched_show_task+0x306/0x3b0 at addr ffff880043c97c18
Read of size 8 by task syz-executor/23839
[...]
page dumped because: kasan: bad access detected
[...]
Call Trace:
[<ffffffff8175ea0e>] __asan_report_load8_noabort+0x3e/0x40
[<ffffffff813e7a26>] sched_show_task+0x306/0x3b0
[<ffffffff813e7bf4>] show_state_filter+0x124/0x1a0
[<ffffffff82d2ca00>] fn_show_state+0x10/0x20
[<ffffffff82d2cf98>] k_spec+0xa8/0xe0
[<ffffffff82d3354f>] kbd_event+0xb9f/0x4000
[<ffffffff843ca8a7>] input_to_handler+0x3a7/0x4b0
[<ffffffff843d1954>] input_pass_values.part.5+0x554/0x6b0
[<ffffffff843d29bc>] input_handle_event+0x2ac/0x1070
[<ffffffff843d3a47>] input_inject_event+0x237/0x280
[<ffffffff843e8c28>] evdev_write+0x478/0x680
[<ffffffff817ac653>] __vfs_write+0x113/0x480
[<ffffffff817ae0e7>] vfs_write+0x167/0x4a0
[<ffffffff817b13d1>] SyS_write+0x111/0x220
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: glider@google.com
Cc: kasan-dev@googlegroups.com
Cc: kcc@google.com
Cc: linux-kernel@vger.kernel.org
Cc: ryabinin.a.a@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Add missing PAN toggling in the futex code
- Fix missing #include that briefly caused issues in -next
- Allow changing of vmalloc permissions with set_memory_* (used by bpf)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJWs2KkAAoJELescNyEwWM0kn4H+gIGvX7Dk792AJlLj8u1hIb6
m+Z4hgLcNIFZCWEGEEWOjHAJ1n2+SgRPdJgDmhN4KP+5Oh9+Qkqhj3wDy7RB05Bf
q3B/dZzr/rASRpycOyNL4CoyqScS7YsP9+X+7tNC8dAMr8UeYahvVKYVwzMlXfDh
4hh3gZkhBQ/hIUse02VtE+OR6lbZAwMYahrM2T9YHslNKanQkpezqBVD4Ic0J5ic
Jkpep8tBdTBLrFm4WERoO6vv8YCrXDP+6DutAO/nOmvHTr07LgkRwiOn+HmoCxiv
Ir5j01SV2SNlr7AfLBWBLN/NluoRByzmQ6SeEsQ3thN35fIsVndStKcAQAAu1nU=
=pr2h
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Nothing particularly interesting here, but all important fixes
nonetheless:
- Add missing PAN toggling in the futex code
- Fix missing #include that briefly caused issues in -next
- Allow changing of vmalloc permissions with set_memory_* (used by
bpf)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: asm: Explicitly include linux/personality.h in asm/page.h
arm64: futex.h: Add missing PAN toggling
arm64: allow vmalloc regions to be set with set_memory_*
The watchdog timer on the SoCFPGA platform is the Synopsys Designware watchdog.
Enable CONFIG_DW_WATCHDOG for the driver to get built.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.
Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.
The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
TASK_SIZE was defined as 0x7fff8000UL which for 64k pages is not a
multiple of the page size. Somewhere further down the math fails
such that executing an ELF binary fails.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tested-by: Joshua Henderson <joshua.henderson@microchip.com>
asm/page.h uses READ_IMPLIES_EXEC from linux/personality.h but does not
explicitly include it causing build failures in -next where whatever was
causing it to be implicitly included has changed to remove that
inclusion. Add an explicit inclusion to fix this.
Signed-off-by: Mark Brown <broonie@kernel.org>
[will: moved #include inside #ifndef __ASSEMBLY__ block]
Signed-off-by: Will Deacon <will.deacon@arm.com>
futex.h's futex_atomic_cmpxchg_inatomic() does not use the
__futex_atomic_op() macro and needs its own PAN toggling. This was missed
when the feature was implemented.
Fixes: 338d4f49d6 ("arm64: kernel: Add support for Privileged Access Never")
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The range of set_memory_* is currently restricted to the module address
range because of difficulties in breaking down larger block sizes.
vmalloc maps PAGE_SIZE pages so it is safe to use as well. Update the
function ranges and add a comment explaining why the range is restricted
the way it is.
Suggested-by: Laura Abbott <labbott@fedoraproject.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Fix the code to fetch and decode the whole 32-bit instruction. This
only really matters with the `noulri' kernel parameter as all microMIPS
processors are supposed to have all the hardware registers we support.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12281/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the regular MIPS instruction set RDHWR is encoded with the SPECIAL3
(011111) major opcode. Therefore it cannot trigger the CpU (Coprocessor
Unusable) exception, and certainly not for coprocessor 0, as the opcode
does not overlap with any of the older ISA reservations, i.e. LWC0
(110000), SWC0 (111000), LDC0 (110100) or SDC0 (111100). The closest
match might be SDC3 (111111), possibly causing a CpU #3 exception,
however our code does not handle it anyway. A quick check with a MIPS I
and a MIPS III processor:
CPU0 revision is: 00000220 (R3000)
CPU0 revision is: 00000440 (R4400SC)
indeed indicates that the RI (Reserved Instruction) exception is
triggered. It's only LL and SC that require emulation in the CpU #0
exception handler as they reuse the LWC0 and SWC0 opcodes respectively.
In the microMIPS instruction set RDHWR is mandatory and triggering the
RI exception is required on unimplemented or disabled register accesses.
Therefore emulating the microMIPS instruction in the CpU #0 exception
handler is not required either.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12280/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
The FPU should not be left enabled after a task context switch. This
isn't usually a problem as the FPU enable bit is updated before
returning to userland, however it can potentially mask kernel bugs, and
in fact KVM assumes it won't happen and won't clear the FPU enable bit
before returning to the guest, which allows the guest to use stale FPU
context.
Interrupts and exceptions save and restore most bits of the CP0 Status
register which contains the FPU enable bit (CU1). When the kernel needs
to enable or disable the FPU (for example due to attempted FPU use by
userland, or the scheduler being invoked) both the actual Status
register and the saved value in the userland context are updated.
However this doesn't work correctly with full kernel preemption enabled,
since the FPU enable bit can be cleared from within an interrupt when
the scheduler is invoked, and only the userland context is updated, not
the interrupt context.
For example:
1) Enter kernel with FPU already enabled, TIF_USEDFPU=1, Status.CU1=1
saved.
2) Take a timer interrupt while in kernel mode, Status.CU1=1 saved.
3) Timer interrupt invokes scheduler to preempt the task, which clears
TIF_USEDFPU, disables the FPU in Status register (Status.CU1=0), and
the value stored in user context from step (1), but not the interrupt
context from step (2).
4) When the process is scheduled back in again Status.CU1=0.
5) The interrupt context from step (2) is restored, which sets
Status.CU1=1. So from user context point of view, preemption has
re-enabled FPU!
6) If the scheduler is invoked again (via preemption or voluntarily)
before returning to userland, TIF_USEDFPU=0 so the FPU is not
disabled before the task context switch.
7) The next task resumes from the context switch with FPU enabled!
The restoring of the Status register on return from interrupt/exception
is already selective about which bits to restore, leaving the interrupt
mask bits alone so enabling/disabling of CPU interrupt lines can
persist. Extend this to also leave both the CU1 bit (FPU enable) and the
FR bit (which specifies the FPU mode and gets changed with CU1). This
prevents a stale Status value being restored in step (5) above and
persisting through subsequent context switches.
Also switch to the use of definitions from asm/mipsregs.h while we're at
it.
Since this change also affects the restoration of Status register on the
path back to userland, it increases the sensitivity of the kernel to the
problem of the FPU being left enabled, allowing it to propagate to
userland, therefore a warning is also added to lose_fpu_inatomic() to
point out any future reoccurances before they do any damage.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12303/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
start_thread() (called for execve(2)) clears the TIF_USEDFPU flag
without atomically disabling the FPU. With a preemptive kernel, an
unfortunately timed preemption after this could result in another
task (or KVM guest) being scheduled in with the FPU still enabled, since
lose_fpu_inatomic() only turns it off if TIF_USEDFPU is set.
Use lose_fpu(0) instead of the separate FPU / MSA management, which
should do the right thing (drop FPU properly and atomically without
saving state) and will be more future proof.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12302/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit 4c21b8fd8f ("MIPS: seccomp: Handle indirect system calls
(o32)"), syscall_get_arguments() attempts to handle o32 indirect syscall
arguments by incrementing both the start argument number and the number
of arguments to fetch. However only the start argument number needs to
be incremented. The number of arguments does not change, they're just
shifted up by one, and in fact the output array is provided by the
caller and is likely only n entries long, so reading more arguments
overflows the output buffer.
In the case of seccomp, this results in it fetching 7 arguments starting
at the 2nd one, which overflows the unsigned long args[6] in
populate_seccomp_data(). This clobbers the $s0 register from
syscall_trace_enter() which __seccomp_phase1_filter() saved onto the
stack, into which syscall_trace_enter() had placed its syscall number
argument. This caused Chromium to crash.
Credit goes to Milko for tracking it down as far as $s0 being clobbered.
Fixes: 4c21b8fd8f ("MIPS: seccomp: Handle indirect system calls (o32)")
Reported-by: Milko Leporis <milko.leporis@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.15-
Patchwork: https://patchwork.linux-mips.org/patch/12213/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NqvQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps with the most intrusive stuff being read-only data
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
* tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: Fix wl12xx missing clocks that cause hangs
ARM: OMAP: Add PWM dmtimer platform data quirks
ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modules
ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodata
ARM: OMAP2+: Fix l2_inv_api_params for rodata
ARM: OMAP2+: Fix save_secure_ram_context for rodata
ARM: OMAP2+: Fix l2dis_3630 for rodata
ARM: OMAP2+: Fix wait_dll_lock_timed for rodata
ARM: OMAP2+: Remove legacy mailbox device instantiation
ARM: dts: AM4372: Add ti,mbox-send-noirq to wkup_m3 mailbox
ARM: dts: AM33xx: Add ti,mbox-send-noirq to wkup_m3 mailbox
...
Signed-off-by: Olof Johansson <olof@lixom.net>
