When a powered on dual-mode controller has been configured to operate
as LE only with secure connections, then the BR/EDR side of things can
not be switched back on. Do reconfigure the controller it first needs
to be powered down.
The secure connections feature is implemented in the BR/EDR controller
while for LE it is implemented in the host. So explicitly forbid such
a transaction to avoid inconsistent states.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BR/EDR Secure Connections feature should only be enabled when the
Secure Simple Pairing mode has been enabled first. However since secure
connections is feature that is valid for BR/EDR and LE, this needs
special handling.
When enabling secure connections on a LE only configured controller,
thent the BR/EDR side should not be enabled in the controller. This
patches makes the BR/EDR Secure Connections feature depending on
enabling Secure Simple Pairing mode first.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Start Discovery was reporting 0 RSSI for invalid RSSI only for
BR/EDR devices. LE devices were reported with RSSI 127.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.19+
When the controller gets powered on via the management interface, then
register the supported SMP channels. There is no point in registering
these channels earlier since it is not know what identity address the
controller is going to operate with.
When powering down a controller unregister all SMP channels. This is
required since a powered down controller is allowed to change its
identity address.
In addition the SMP channels are only available when the controller
is powered via the management interface. When using legacy ioctl, then
Bluetooth Low Energy is not supported and registering kernel side SMP
integration may actually cause confusion.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For dual-mode controllers it is possible to disable BR/EDR and operate
as LE single mode controllers with a static random address. If that is
the case, then refuse switching BR/EDR back on after the controller has
been powered.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When hci_req_run() calls its provided complete function and one of the
HCI commands in the sequence fails, then provide the opcode of failing
command. In case of success HCI_OP_NOP is provided since all commands
completed.
This patch fixes the prototype of hci_req_complete_t and all its users.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The force_sc_support debugfs option was introduced to easily work with
pre-production Bluetooth 4.1 silicon. This option is no longer needed
since controllers supporting BR/EDR Secure Connections feature are now
available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The cmd_complete callbacks for pending mgmt commands may fail e.g. in
the case of memory allocation. Previously this error would be caught and
returned to user space in the form of a failed write on the mgmt socket
(when the error happened in the mgmt command handler) but with the
introduction of the generic cmd_complete callback this information was
lost. This patch returns the feature by making cmd_complete callbacks
return int instead of void.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates the Add Device mgmt command handler to use a
hci_request to wait for HCI command completion before notifying user
space of the mgmt command completion. To do this we need to add an extra
hci_request parameter to the hci_conn_params_set function. Since this
function has no other users besides mgmt.c it's moved there as a static
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates the Remove Device mgmt command handler to use a
hci_request to wait for HCI command completion before notifying user
space of the mgmt command completion. This way we ensure that once the
mgmt command returns all HCI commands triggered by it have also
completed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Many places using hci_update_background_scan() try to synchronize
whatever they're doing with the help of hci_request callbacks. However,
since the hci_update_background_scan() function hasn't so far accepted a
hci_request pointer any commands triggered by it have been left out by
the synchronization. This patch modifies the API in a similar way as was
done for hci_update_page_scan, i.e. there's a variant that takes a
hci_request and another one that takes a hci_dev.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
None of the hci_request related things in net/bluetooth/hci_core.h are
needed anywhere outside of the core bluetooth module. This patch creates
a new net/bluetooth/hci_request.c file with its corresponding h-file and
moves the functionality there from hci_core.c and hci_core.h.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To keep the parameter list and its semantics clear it makes sense to
split the hci_update_page_scan function into two separate functions: one
taking a hci_dev and another taking a hci_request. The one taking a
hci_dev constructs its own hci_request and then calls the other
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The optimization for filtering out extended inquiry results, advertising
reports or scan response data based on provided UUID list has a logic
bug. In case no match is found in the advertising data, the scan
response is ignored and not checked against the filter. This will lead
to events being filtered wrongly.
Change the code to actually only drop the events when the scan response
data is not present. If it is present, it needs to be checked against
the provided filter.
The patch is a bit more complex than it needs to be. That is because
it also fixes this compiler warning that some gcc versions produce.
CC net/bluetooth/mgmt.o
net/bluetooth/mgmt.c: In function ‘mgmt_device_found’:
net/bluetooth/mgmt.c:7028:7: warning: ‘match’ may be used uninitialized in this function [-Wmaybe-uninitialized]
bool match;
^
It seems that gcc can not clearly figure out the context of the match
variable. So just change the branches for the extended inquiry response
and advertising data around so that it is clear.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When an adapter is removed (hci_unregister_dev) any pending mgmt
commands for that adapter should get the appropriate INVALID_INDEX
response. Since hci_unregister_dev() calls hci_dev_do_close() first
that'd so far have caused "not powered" responses to be sent.
Skipping the HCI_UNREGISTER case in mgmt_powered() is also not a
solution since before reaching the mgmt_index_removed() stage any
hci_conn callbacks (e.g. used by pairing) will get called, thereby
causing "disconnected" status responses to be sent.
The fix that covers all scenarios is to handle both INVALID_INDEX and
NOT_POWERED responses through the mgmt_powered() function. The
INVALID_INDEX response sending from mgmt_index_removed() is left
untouched since there are a couple of places not related to powering off
or removing an adapter that call it (e.g. configuring a new bdaddr).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we're in the AUTO_OFF stage the powered_update_hci() function is
responsible for doing the updates to the HCI state that were not done
during the actual mgmt command handlers. One of the updates needing done
is for BR/EDR SC support. This patch adds the missing HCI command for SC
support to the powered_update_hci() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The pairing_complete() function is used as a pending mgmt command
cmd_complete callback. The expectation of such functions is that they
are not responsible themselves for calling mgmt_pending_remove(). This
patch fixes the incorrect mgmt_pending_remove() call in
pairing_complete() and adds it to the appropriate changes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The pairing_complete() function relies on a hci_conn reference to be
able to access the hci_conn object. It should therefore only release
this reference once it's done accessing the object, i.e. at the end of
the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
mgmt_pending_remove() should be called with hci_dev_lock protection
and currently the rule to take dev lock is that all mgmt req_complete
functions should take dev lock. So this patch fixes the same in the
missing functions
Without this patch there is a chance of invalid memory access while
accessing the mgmt_pending list like below
bluetoothd: 392] [0] Backtrace:
bluetoothd: 392] [0] [<c04ec770>] (pending_eir_or_class+0x0/0x68) from [<c04f1830>] (add_uuid+0x34/0x1c4)
bluetoothd: 392] [0] [<c04f17fc>] (add_uuid+0x0/0x1c4) from [<c04f3cc4>] (mgmt_control+0x204/0x274)
bluetoothd: 392] [0] [<c04f3ac0>] (mgmt_control+0x0/0x274) from [<c04f609c>] (hci_sock_sendmsg+0x80/0x308)
bluetoothd: 392] [0] [<c04f601c>] (hci_sock_sendmsg+0x0/0x308) from [<c03d4d68>] (sock_aio_write+0x144/0x174)
bluetoothd: 392] [0] r8:00000000 r7 7c1be90 r6 7c1be18 r5:00000017 r4 a90ea80
bluetoothd: 392] [0] [<c03d4c24>] (sock_aio_write+0x0/0x174) from [<c00e2d4c>] (do_sync_write+0xb0/0xe0)
bluetoothd: 392] [0] [<c00e2c9c>] (do_sync_write+0x0/0xe0) from [<c00e371c>] (vfs_write+0x134/0x13c)
bluetoothd: 392] [0] r8:00000000 r7 7c1bf70 r6:beeca5c8 r5:00000017 r4 7c05900
bluetoothd: 392] [0] [<c00e35e8>] (vfs_write+0x0/0x13c) from [<c00e3910>] (sys_write+0x44/0x70)
bluetoothd: 392] [0] r8:00000000 r7:00000004 r6:00000017 r5:beeca5c8 r4 7c05900
bluetoothd: 392] [0] [<c00e38cc>] (sys_write+0x0/0x70) from [<c000e3c0>] (ret_fast_syscall+0x0/0x30)
bluetoothd: 392] [0] r9 7c1a000 r8:c000e568 r6:400b5f10 r5:403896d8 r4:beeca604
bluetoothd: 392] [0] Code: e28cc00c e152000c 0a00000f e3a00001 (e1d210b8)
bluetoothd: 392] [0] ---[ end trace 67b6ac67435864c4 ]---
bluetoothd: 392] [0] Kernel panic - not syncing: Fatal exception
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
John W. Linville says:
====================
pull request: wireless-next 2014-12-08
Please pull this last batch of pending wireless updates for the 3.19 tree...
For the wireless bits, Johannes says:
"This time I have Felix's no-status rate control work, which will allow
drivers to work better with rate control even if they don't have perfect
status reporting. In addition to this, a small hwsim fix from Patrik,
one of the regulatory patches from Arik, and a number of cleanups and
fixes I did myself.
Of note is a patch where I disable CFG80211_WEXT so that compatibility
is no longer selectable - this is intended as a wake-up call for anyone
who's still using it, and is still easily worked around (it's a one-line
patch) before we fully remove the code as well in the future."
For the Bluetooth bits, Johan says:
"Here's one more bluetooth-next pull request for 3.19:
- Minor cleanups for ieee802154 & mac802154
- Fix for the kernel warning with !TASK_RUNNING reported by Kirill A.
Shutemov
- Support for another ath3k device
- Fix for tracking link key based security level
- Device tree bindings for btmrvl + a state update fix
- Fix for wrong ACL flags on LE links"
And...
"In addition to the previous one this contains two more cleanups to
mac802154 as well as support for some new HCI features from the
Bluetooth 4.2 specification.
From the original request:
'Here's what should be the last bluetooth-next pull request for 3.19.
It's rather large but the majority of it is the Low Energy Secure
Connections feature that's part of the Bluetooth 4.2 specification. The
specification went public only this week so we couldn't publish the
corresponding code before that. The code itself can nevertheless be
considered fairly mature as it's been in development for over 6 months
and gone through several interoperability test events.
Besides LE SC the pull request contains an important fix for command
complete events for mgmt sockets which also fixes some leaks of hci_conn
objects when powering off or unplugging Bluetooth adapters.
A smaller feature that's part of the pull request is service discovery
support. This is like normal device discovery except that devices not
matching specific UUIDs or strong enough RSSI are filtered out.
Other changes that the pull request contains are firmware dump support
to the btmrvl driver, firmware download support for Broadcom BCM20702A0
variants, as well as some coding style cleanups in 6lowpan &
ieee802154/mac802154 code.'"
For the NFC bits, Samuel says:
"With this one we get:
- NFC digital improvements for DEP support: Chaining, NACK and ATN
support added.
- NCI improvements: Support for p2p target, SE IO operand addition,
SE operands extensions to support proprietary implementations, and
a few fixes.
- NFC HCI improvements: OPEN_PIPE and NOTIFY_ALL_CLEARED support,
and SE IO operand addition.
- A bunch of minor improvements and fixes for STMicro st21nfcb and
st21nfca"
For the iwlwifi bits, Emmanuel says:
"Major works are CSA and TDLS. On top of that I have a new
firmware API for scan and a few rate control improvements.
Johannes find a few tricks to improve our CPU utilization
and adds support for a new spin of 7265 called 7265D.
Along with this a few random things that don't stand out."
And...
"I deprecate here -8.ucode since -9 has been published long ago.
Along with that I have a new activity, we have now better
a infrastructure for firmware debugging. This will allow to
have configurable probes insides the firmware.
Luca continues his work on NetDetect, this feature is now
complete. All the rest is minor fixes here and there."
For the Atheros bits, Kalle says:
"Only ath10k changes this time and no major changes. Most visible are:
o new debugfs interface for runtime firmware debugging (Yanbo)
o fix shared WEP (Sujith)
o don't rebuild whenever kernel version changes (Johannes)
o lots of refactoring to make it easier to add new hw support (Michal)
There's also smaller fixes and improvements with no point of listing
here."
In addition, there are a few last minute updates to ath5k,
ath9k, brcmfmac, brcmsmac, mwifiex, rt2x00, rtlwifi, and wil6210.
Also included is a pull of the wireless tree to pick-up the fixes
originally included in "pull request: wireless 2014-12-03"...
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the host decides to use a non-resolvable private address, it
must ensure that this generated address does not match the public
address of the controller. Add an extra check to ensure this required
behavior.
In addition rename the variable from urpa to nrpa and fix all of the
comments in the code that use the term unresolvable instead of the
term non-resolvable as used in the Bluetooth specification.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using Start Service Discovery and when background scanning is used
to report devices, the RSSI is reported or the value 127 is provided in
case RSSI in unavailable.
For Start Discovery the value 0 is reported to keep backwards
compatibility with the existing users.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When no RSSI value is available then make sure that the result is
filtered out when the RSSI threshold filter is active.
This means that all Bluetooth 1.1 or earlier devices will not
report any results when using a RSSI threshold filter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The mgmt.c file already has a bluetooth_base_uuid variable which has the
exact same value as the reverse_base_uuid one. This patch removes the
redundant variable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes the Get Connection Information mgmt command to take
advantage of the new cmd_complete callback. This allows for great
simplifications in the logic for constructing the cmd_complete event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the Get Clock Information mgmt command to take
advantage of the new cmd_complete callback for pending commands.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the Start/Stop Discovery mgmt commands to use the
cmd_complete callback of struct pending_cmd. Since both of these
commands return the same parameters as they take as input we can use the
existing generic_cmd_complete() helper for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates the Unpair Device code to take advantage of the
cmd_complete callback of struct pending_cmd.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the Pair Device mgmt command to use the new
cmd_complete callback for pending mgmt commands. The already existing
pairing_complete() function is exactly what's needed and doesn't need
changing.
In addition to getting the return parameters always right this patch
actually fixes a reference counting bug and memory leak with the
hci_conn that's attached to the pending mgmt command - something that
would occur when powering off or unplugging the adapter while pairing is
in progress.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the user confirmation & PIN code mgmt commands to
take advantage of the new cmd_complete callback for pending mgmt
commands. The patch also adds a new generic addr_cmd_complete() helper
function to be used with commands that send a mgmt_addr_info response
based on a mgmt_addr_info in the beginning of the command parameters.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the Disconnect mgmt command to take advantage of the
new cmd_complete callback that's part of the pending_cmd struct. There
are many commands whose response parameters map 1:1 to the command
parameters and Disconnect is one of them. This patch adds a
generic_cmd_complete() function for such commands that can be reused in
subsequent patches.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As preparation for making generic cmd_complete responses possible we'll
need to track the parameter length in addition to just a pointer to
them. This patch adds the necessary variable to the pending_cmd struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We've got a couple of generic scenarios where all pending mgmt commands
are processed and responses are sent to them. These scenarios are
powering off the adapter and removing the adapter. So far the code has
been generating cmd_status responses with NOT_POWERED and INVALID_INDEX
resposes respectively, but this violates the mgmt specification for
commands that should always generate a cmd_complete.
This patch adds support for specifying a callback for the pending_cmd
context that each command handler can use for command-specific
cmd_complete event generation. The actual per-command event generators
will come in subsequent patches.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of failure or when unplugging a controller, the allocated
memory for the UUID list of the discovery filter is not freed. Use
the newly introduced helper for reset the discovery filter and with
that also freeing existing memory.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds support for the Start Service Discovery command. It
does all the checks for command parameters and configured the discovery
filter settings correctly. However the actual support for filtering
will be added with another patch.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The previous patch provided the framework for integrating the UUID
filtering into the service discovery. This patch now provides the
actual filter logic.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Using Start Service Discovery provides the option to specifiy a list
of UUID that are used to filter out device found events. This patch
provides the framework for hooking up the UUID filter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Using Start Service Discovery allows to provide a RSSI threshold. This
patch implements support for filtering out device found events based
on the provided value.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the upcoming addition of support for Start Service Discovery, the
discovery handling needs to filter on RSSI and UUID values. For that
they need to be stored in the discovery handling. This patch adds the
appropiate fields and also make sure they are reset when discovery
has been stopped.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The actual process of compiling the correct HCI commands for triggering
discovery is something that should be generic. So instead of mixing it
into the Start Discover operation handling, split it out into its own
function utilizing HCI request handling and just providing status in
case of errors or invalid parameters.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Sending the required cmd_complete for the management commands should be
done in one place and not in multiple places. Especially for Start and
Stop Discovery commands this is split into to sending it in case of
failure from the complete handler, but in case of success from the
event state update function triggering mgmt_discovering. This is way
too convoluted and since hci_request serializes the HCI command
processing, send the cmd_complete response from the complete handler
for all cases.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Start Discovery command has some complicated code when it comes
to error handling. With the future introduction of Start Service
Discovery simplifying this makes it easier to read.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch increments the management interface revision due to the
addition of support for LE Secure Connection feature.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds proper support for passing LE OOB data to the
hci_add_remote_oob_data() function. For LE the 192-bit values are not
valid and should therefore be passed as NULL values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be able to support OOB data for LE pairing we need to store the
address type of the remote device. This patch extends the relevant
functions and data types with a bdaddr_type variable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no need to duplicate code for the 192 vs 192+256 variants of the
OOB data functions. This is also helpful to pave the way to support LE
SC OOB data where only 256 bit data is provided.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since LE Secure Connections is a purely host-side feature we should
offer the Secure Connections mgmt setting for any adapter with LE
support. This patch updates the supported settings value and the
set_secure_conn command handler accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the HCI_SC_ENABLED flag will also be used for controllers without
BR/EDR Secure Connections support whenever we need to check specifically
for SC for BR/EDR we also need to check that the controller actually
supports it. This patch adds a convenience macro for check all the
necessary conditions and converts the places in the code that need it to
use it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We need a dedicated LTK type for LTK resulting from a Secure Connections
based SMP pairing. This patch adds a new define for it and ensures that
both the New LTK event as well as the Load LTKs command supports it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The common short form of "randomizer" is "rand" in many places
(including the Bluetooth specification). The shorter version also makes
for easier to read code with less forced line breaks. This patch renames
all occurences of "randomizer" to "rand" in the Bluetooth subsystem
code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For now the mgmt commands dealing with remote OOB data are strictly
BR/EDR-only. This patch fixes missing checks for the passed address type
so that any non-BR/EDR value triggers the appropriate error response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When passed BDADDR_ANY the Remove Remote OOB Data comand is specified to
clear all entries. This patch adds the necessary check and calls
hci_remote_oob_data_clear() when necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to Management Interface API 'Start Discovery' command should
generate a Command Complete event on failure. Currently kernel is
sending Command Status on early errors. This results in userspace
ignoring such event due to invalid size.
bluetoothd[28499]: src/adapter.c:trigger_start_discovery()
bluetoothd[28499]: src/adapter.c:cancel_passive_scanning()
bluetoothd[28499]: src/adapter.c:start_discovery_timeout()
bluetoothd[28499]: src/adapter.c:start_discovery_complete() status 0x0a
bluetoothd[28499]: Wrong size of start discovery return parameters
Reported-by: Jukka Taimisto <jtt@codenomicon.com>
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Systematically removing the LE connection parameters and autoconnect
action is inconvenient for rebonding without disconnecting from
userland (i.e. unpairing followed by repairing without
disconnecting). The parameters will be lost after unparing and
userland needs to take care of book-keeping them and re-adding them.
This patch allows userland to forget about parameter management when
rebonding without disconnecting. It defers clearing the connection
parameters when unparing without disconnecting, giving a chance of
keeping the parameters if a repairing happens before the connection is
closed.
Signed-off-by: Alfonso Acosta <fons@spotify.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
NULL-checking conn->dev_class is pointless since the variable is
defined as an array, i.e. it will always be non-NULL.
Signed-off-by: Alfonso Acosta <fons@spotify.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are scenarios when autoconnecting to a device after the
reception of an ADV_IND report (action 0x02), in which userland
might want to examine the report's contents.
For instance, the Service Data might have changed and it would be
useful to know ahead of time before starting any GATT procedures.
Also, the ADV_IND may contain Manufacturer Specific data which would
be lost if not propagated to userland. In fact, this patch results
from the need to rebond with a device lacking persistent storage which
notifies about losing its LTK in ADV_IND reports.
This patch appends the ADV_IND report which triggered the
autoconnection to the EIR Data in the Device Connected event.
Signed-off-by: Alfonso Acosta <fons@spotify.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The values of a lot of the mgmt_device_connected() parameters come
straight from a hci_conn object. We can simplify the function by passing
the full hci_conn pointer to it.
Signed-off-by: Alfonso Acosta <fons@spotify.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Whether through HCI with BR/EDR or SMP with LE when authentication fails
we should also notify any pending Pair Device mgmt command. This patch
updates the mgmt_auth_failed function to take the actual hci_conn object
and makes sure that any pending pairing command is notified and cleaned
up appropriately.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no reason to custom build the HCI_Disconnect command in the
Disconnect Device mgmt command handler. This patch updates the code to
use hci_disconnect() instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Wherever we keep hci_conn pointers around we should be using
hci_conn_get/put to ensure that they stay valid. This patch fixes
all places violating against the principle currently.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Similar to our hci_update_background_scan() function we can simplify a
lot of code by creating a unified helper function for doing page scan
updates. This patch adds such a function to hci_core.c and updates all
the relevant places to use it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are several situations where we're interested in knowing whether
we're currently in the process of powering off an adapter. This patch
adds a convenience function for the purpose and makes it public since
we'll soon need to access it from hci_event.c as well.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This setting maps to the HCI_BONDABLE flag which tracks whether we're
bondable or not. Therefore, rename the mgmt setting and respective
command accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The HCI_PAIRABLE flag isn't actually controlling whether we're pairable
but whether we're bondable. Therefore, rename it accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Both BT_CONNECTED and BT_CONFIG state mean that we have a baseband link
available. We should therefore check for either of these when pairing
and deciding whether to call hci_conn_security() directly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have entries in the whitelist we shouldn't disable page scanning
when disabling connectable mode. This patch adds the necessary check to
the Set Connectable command handler.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the Bluetooth 4.1 specification the Simultaneous LE and BR/EDR
controller option has been deprecated. It shall be set to zero and
ignored otherwise.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Store the default values for minimum and maximum advertising interval
with all the other controller defaults. These vaules are sent to the
adapter whenever advertising is (re)enabled.
Signed-off-by: Georg Lukas <georg@op-co.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When adding remote devices to the kernel using the Add Device management
command, these devices are explicitly allowed to connect. This kind of
incoming connections are possible even when the controller itself is
not connectable.
For BR/EDR this distinction is pretty simple since there is only one
type of incoming connections. With LE this is not that simple anymore
since there are ADV_IND and ADV_DIRECT_IND advertising events.
The ADV_DIRECT_IND advertising events are send for incoming (slave
initiated) connections only. And this is the only thing the kernel
should allow when adding devices using action 0x01. This meaning
of incoming connections is coming from BR/EDR and needs to be
mapped to LE the same way.
Supporting the auto-connection of devices using ADV_IND advertising
events is an important feature as well. However it does not map to
incoming connections. So introduce a new action 0x02 that allows
the kernel to connect to devices using ADV_DIRECT_IND and in addition
ADV_IND advertising reports.
This difference is represented by the new HCI_AUTO_CONN_DIRECT value
for only connecting to ADV_DIRECT_IND. For connection to ADV_IND and
ADV_DIRECT_IND the old value HCI_AUTO_CONN_ALWAYS is used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We're interested in whether an authentication request is because of a
remote or local action. So far hci_conn_security() has been used both
for incoming and outgoing actions (e.g. RFCOMM or L2CAP connect
requests) so without some modifications it cannot know which peer is
responsible for requesting authentication.
This patch adds a new "bool initiator" parameter to hci_conn_security()
to indicate which side is responsible for the request and updates the
current users to pass this information correspondingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make the code more understandable it makes sense to use the new HCI
defines for connection role instead of a "bool master" parameter. This
makes it immediately clear when looking at the function calls what the
last parameter is describing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Set Connectable/Discoverable mgmt handlers use a hci_request with a
proper callback to handle the HCI command sending. It makes therefore
little sense to have this extra function to be called from hci_event.c
for command failures.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the HCISETSCAN ioctl is the only non-mgmt user we care about for
setting the right discoverable state we can simply do the necessary
updates in the ioctl handler function instead. This then allows the
removal of the mgmt_discoverable function and should simplify that state
handling considerably.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The mgmt_connectable function has been used to ensure that the right
actions to HCI_CONNECTABLE are taken when the HCI_Write_Scan_Enable
command is triggered by something else than mgmt. The only other user
that we really care about is the HCISETSCAN ioctl code, so we can
actually more simply perform the needed changes there instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we change the connectable state and have advertising enabled we
should update the advertising parameters no matter what. The code was
incorrectly only updating them if advertising was not already active.
This patch fixes the issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the white list is in use the code would not update the
HCI_CONNECTABLE flag if it gets changed through the ioctl code (e.g.
hciconfig hci0 pscan). Since the flag is important for properly
accepting incoming connections add code to fix it up if necessary and
emit a New Settings mgmt event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Page scan should be enabled either if the connectable setting is set or
if there are any entries in the BR/EDR white list. This patch implements
such behavior by updating the two places that were making decisions on
whether to enable page scan or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since page scan might be enabled by Add Device we should not implicitly
set connectable whenever something else than Set Connectable changes it.
This patch makes sure that we don't set HCI_CONNECTABLE for these cases
if there are any entries in the white list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're removing the last item in the white list or adding the first
one to it and HCI_CONNECTABLE is not set we need to update the current
page scan. This patch adds a simple helper function for the purpose and
calls it from the respective mgmt command handlers.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch extends the Add/Remove device commands by letting user space
pass BR/EDR addresses to them. The resulting entries get stored in a new
hdev->whitelist list. The idea is that we can now selectively accept
connections from devices in the list even though HCI_CONNECTABLE is not
set (the actual implementation of this is coming in a subsequent patch).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We already have several lists with struct bdaddr_list entries, and there
will be more in the future. Since the operations for adding, removing,
looking up and clearing entries in these lists are exactly the same it
doesn't make sense to define new functions for every single list. This
patch unifies the functions by passing the list_head to them instead of
a hci_dev pointer.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the connectable state change doesn't require any special HCI commands
the set_connectable_update_settings() function is used instead of the
set_connectable_complete() function. We must therefore make sure to call
hci_update_background_scan() there as well. This code path is used also
when we're powered off, but that's fine since hci_update_background_scan()
has the necessary checks for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The connectable and discoverable mgmt settings are supported both for LE
and BR/EDR controllers so they do not belong behind a lmp_bredr_capable()
condition. This patch fixes the issue in get_supported_settings().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If any of the HCI commands from the hci_stop_discovery function were
successfully sent we need to set the discovery state to STOPPING. The
Stop Discovery code was already handling this, but the code in
clean_up_hci_state was not. This patch updates the hci_stop_discovery to
return a bool to indicate whether it queued any commands and the
clean_up_hci_state() function respectively to look at the return value
and call hci_discovery_set_state() if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Many controllers allow simultaneous active scanning and advertising
(e.g. Intel and Broadcom) but some do not (e.g. CSR). It's therefore
safest to implement mutual exclusion of these states in the kernel.
This patch ensures that the two states are never entered simultaneously.
Extra precaution needs to be taken for outgoing connection attempts in
slave role (i.e. through directed advertising) in which case the
operation that came first has precedence and the one that comes after
gets a rejection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When deciding to call disable_advertising() we're interested in the real
state instead of the mgmt setting. Use therefore HCI_LE_ADV instead of
the HCI_ADVERTISING flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By adding support for disabling advertising when necessary and doing the
checks for existing LE connections inside the enable_advertising
function we can simplify the calling code quite a lot.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that we have a flag for tracking the real advertising state we
should use that to determine whether it's safe to update the random
address or not. The couple of places that were clearing the flag due to
a pending request need to be updated too.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the real advertising state is now tracked with its own flag we can
simply set/unset the HCI_ADVERTISING flag in the
set_advertising_complete function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For adapters that do not support LE and ones where LE hasn't been
enabled we shouldn't be trying to initiate background scanning. This
patch adds an extra check to the hci_update_background_scan() to ensure
that we bail out if HCI_LE_ENABLED is not set.
Since we do allow user space to feed the kernel with LE connection
parameters even when LE is not enabled we now need to also call
hci_update_background_scan() as soon as LE gets enabled so that scanning
gets started if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have both LE scanning and advertising simultaneously enabled we
need a way to tell hci_connect_le() in which role to initiate a
connection. This patch adds a new parameter to the function to give it
the necessary information. For auto-connect and mgmt_pair_device we
always use master role, whereas for L2CAP users (in practice sockets) we
use slave role whenever HCI_ADVERTISING is set and master role
otherwise.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The auth_type value which gets assigned to hci_conn->auth_type is
something that's only used for BR/EDR connections and is of no value for
LE connections. It makes therefore little sense to pass it to the
hci_connect_le() function. This patch removes the parameter from the
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enabling passive scanning always when we're connectable aligns us with
the BR/EDR page scanning. This is also consistent with the fact that the
code dealing with passive scanning results will actively try to connect
any direct advertising event when we're connectable.
This patch implements the feature by adding the connectable condition to
hci_update_background_scan() checks for starting scanning and by calling
hci_update_background_scan() whenever the connectable state changes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that we have the process_adv_report() function doing the IRK lookup
and updating the bdaddr we don't need to do this anymore in mgmt.c in
the mgmt_device_found() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we establish connections as a consequence of receiving an
advertising report it makes no sense to wait the normal 20 second LE
connection timeout. This patch modifies the hci_connect_le function to
take an extra timeout value and uses a lower 2 second timeout for the
auto-connection case. This timeout is intentionally chosen to be just a
bit higher than the 1.28 second timeout that High Duty Cycle Advertising
uses.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When an unconfigured controllers reaches the configured state, it is
important to change the HCI_RAW flag. It indicates to userspace that
the controller is fully operational.
External configuration allows to bring the controller back into an
unconfigured state. In that case make sure HCI_RAW flag is set again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds support for changing the public device address. This feature
is required by controllers that do not provide a public address and
have HCI_QUIRK_INVALID_BDADDR set.
Even if a controller has a public device address, this is useful when
an embedded system wants to use its own value. As long as the driver
provides the set_bdaddr callback, this allows changing the device
address before powering on the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the external configuration triggers the switch to a configured
controller, it means the setup needs to be run. Controllers that start
out unconfigured have only run limited set of HCI commands. This is
not enough for complete operation and thus run the setup procedure
before announcing the new controller index.
This introduces HCI_CONFIG flag as companion to HCI_SETUP flag. The
HCI_SETUP flag is only used once for the initial setup procedure. And
during that procedure hdev->setup driver callback is called. With the
new HCI_CONFIG the switch from unconfigured to configured state is
triggering the same setup procedure just without hdev->setup. This
is required since bringing a controller back to unconfigured state
from configured state is possible.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When calling Device Remove with BDADDR_ANY we should in a similar way
emit Device Removed events as we do when removing a single device. Since
we have to iterate the list and call device_removed() the dedicated
hci_conn_params_clear_enabled() is not really useful anymore. This patch
removes the helper function and does the event emission and list item
removal in a single loop.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When one or more of the missing configuration options change, then send
this even to all the other management interface clients.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move the mgmt_event function higher up in the code so that no forward
declaration is needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Set External Configuration management command allows for switching
between configured and unconfigured start if HCI_QURIK_EXTERNAL_CONFIG
is set by the transport driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller requires external configuration, then setting this
quirk will allow indicating this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Reading the controller configuration information is a valid management
command when the controller is unconfigured. Allow this command, but
return invalid index on all other commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a Bluetooth controller does not have a valid public Bluetooth
address, then allow the driver to indicate this. If the quirk is
set, the Bluetooth core will switch to unconfigured state first
and will allow userspace to configure the address before starting
the full initialization of the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It's wasteful to use list_del_init (which re-initializes the list_head)
if we're just about to free the element and never use it again.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When powering off (hci_dev_do_close) we should clear both the
pend_le_reports and pend_le_conns types of entries. When powering on
respectively we should populate both lists. This patch converts the
hci_pend_le_conns_clear() function into hci_pend_le_actions_clear()
(which can now be static) and converts the restart_le_auto_conns()
function into restart_le_actions().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since params->action is used for both the pend_le_conns and
pend_le_reports lists we can simplify the adding and deleting of the
lists considerably. For example, when deleting entries in most
situations we no-longer need to check the auto_connect value but can
directly proceed with calling list_del_init on param->action (which is
safe even if the entry is not part of any list).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To simplify manipulation and lookup of hci_conn_params entries of the
type HCI_AUTO_CONN_REPORT it makes sense to store them in their own
list. The new action list_head in hci_conn_params is used for this
purpose.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Read Controller Configuration Information command allows retrieving
details about possible configurations option. The supported options are
returned and also the missing options (if any).
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the connection parameters are always a basis for adding entries to
hdev->pend_le_conns (so far of type bdaddr_list) it's simpler and more
efficient to have the parameters themselves be the entries in the
pend_le_conns list. We do this by adding another list_head to the
hci_conn_params struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When calling Remove Device for an entry using HCI_AUTO_CONN_REPORT we
need to decrement the pend_le_reports value correspondingly. This patch
fixes one such missing action in the Remove Device command handler.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The handler for variable length commands were trying to calculate the
expected length of the command based on the given parameter count, and
then comparing that with the received data. However, the expected count
was stored in a u16 which can easily overflow. With a carefully crafted
command this can then be made to match the given data even though the
parameter count is actually way too big, resulting in a buffer overflow
when parsing the parameters.
This patch fixes the issue by calculating a per-command maximum
parameter count and returns INVALID_PARAMS if it is exceeded.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the kernel is doing LE scanning because of one or more devices
added with action 0x00 through the Add Device command we do want to let
mgmt_device_found() to proceed with sending an event. This kind of
devices are tracked with hdev->pend_le_reports, so check this value
before bailing out from the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This command allows to get the list of currently known controller that
are in unconfigured state.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller in an unconfigured state gets removed, then send
Unconfigured Index Removed events.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller is in unconfigured state it is currently hidden
from the management interface. This change now announces the new
controller with an Unconfigured Index Added event and allows clients
to easily detect the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the new unconfigured controller state it is possible to provide a
fully functional HCI transport, but disable the higher level operations
that would normally happen. This way userspace can try to configure the
controller before releases the unconfigured state.
The internal state is represented by HCI_UNCONFIGURED. This replaces the
HCI_QUIRK_RAW_DEVICE quirk as internal state representation. This is now
a real state and drivers can use the quirk to actually trigger this
state. In the future this will allow a more fine grained switching from
unconfigured state to configured state for controller inititialization.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If we don't have an identity address for connection parameters it
doesn't really make sense to send them to user space. Instead just
ignore them for now. Later we can add support for sending them when we
eventually get the identity through pairing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The calling functions of mgmt_new_conn_param have more information about
the parameters, such as whether the kernel is tracking them or not. It
makes therefore sense to have them pass an initial store_hint value to
the mgmt_new_conn_param function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements the new Load Connection Parameters mgmt command
that's intended to load the desired connection parameters for LE
devices.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Remove Device mgmt command is supposed to undo what the Add Device
command does. An entry added by Add Device cannot have the
HCI_AUTO_CONN_DISABLED auto_connect value, so we should treat this as an
invalid entry to remove. This patch adds the necessary pieces to the
Remove Device command handler so that it only removes entries which were
added by Add Device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The 0x00 action value of mgmt means "scan and report" but do not
connect. This is different from HCI_AUTO_CONN_DISABLED so we need a new
value for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon have specific clear functions for clearing enabled or
disabled entries, so rename the function that removes everything to
clear_all().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces a new Mgmt event called "New Connection Parameter".
This event indicates to userspace the connection parameters values the
remote device requested.
The user may store these values and load them into kernel. This way, next
time a connection is established to that device, the kernel will use those
parameters values instead of the default ones.
This event is sent when the remote device requests new connection
parameters through connection parameter update procedure. This event is
not sent for slave connections.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For the Block/Unblock Device mgmt commands we should only emit the
Blocked/Unblocked events on any socket except for the one which received
the command. The code was previously incorrectly trying to look up a
non-existent pending command and thereby ending up not skipping the
command socket for the event.
We can simplify the code a lot by simply sending the event directly from
the command handler functions. We have the reference to the command
socket available there which makes it easy to pass to the mgmt_event
function for skipping.
The only notable side-effect of this is that the old blacklisting
ioctl's no-longer cause mgmt events to be emitted, however as user space
versions using these ioctl's are not mgmt-aware this is acceptable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The background scanning normally gets enabled during power on by
adding devices to the pending connection list. However devices
might be already on that list and the list of devices is empty,
then it is better to trigger the background manually.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Providing the flags parameter directly to mgmt_device_found function
makes the core simpler and more readable. With this it becomes a lot
easier to add new flags in the future.
This also changes hci_inquiry_cache_update to just return that flags
needed for mgmt_device_found since that is its only use for the two
return parameters anyway.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The connection interval parameter of hci_conn_params_set are always used
with the controller defaults. So just let hci_conn_params_add set the
controller default and not bother resetting them to controller defaults
every time the hci_conn_params_set is called.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When trying to pair a new Bluetooth Low Energy device, then make sure
that the default connections parameters are in place before trying to
establish the first connection to that device. With the connection
parameters structure allocated, the slave preferred values can now
easily be tracked and all future connections will use the correct
values from that start decreasing connection establishment time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In some cases it is useful to not overwrite connection parametes and
instead just create default ones if they don't exist. This function
does exactly that. hci_conn_params_add will allow to create new
default connection parameters. hci_conn_params_set will set the
values and also create new parameters if they don't exist.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When devices are added or removed, then make sure that events are send
out to all other clients so that the list of devices can be easily
tracked. This is especially important when external clients are
adding or removing devices within the auto-connection list.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This allows adding or removing devices from the background scanning
list the kernel maintains. Device flagged for auto-connection will
be automatically connected if they are found.
The passive scanning required for auto-connection will be started
and stopped on demand.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Bluetooth controllers that are marked for raw-only usage can only be
used with user channel access. Any other operation should be rejected.
This simplifies the whole raw-only support since it now depends on
the fact that the controller is marked with HCI_QUIRK_RAW_DEVICE and
runtime raw access is restricted to user channel operation.
The kernel internal processing of HCI commands and events is designed
around the case that either the kernel has full control over the device
or that the device is driven from userspace. This now makes a clear
distinction between these two possible operation modes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch implements support for the Get Clock Information mgmt
command. This is done by performing one or two HCI_Read_Clock commands
and creating the response from the stored values in the hci_dev and
hci_conn structs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By using kzalloc we ensure that there are no struct members, such as the
user_data pointer, left uninitialized.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch increments the management interface revision due to the
changes with the debug key command and other fixes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now that the SMP context has it's own crypto handle it doesn't need to
lock the hci_dev anymore for most operations. This means that it is safe
to call smp_user_confirm_reply with the lock already held.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a new valid mode 0x02 for the mgmt_set_debug_keys
command. The 0x02 mode sets the HCI_USE_DEBUG_KEYS flag which makes us
always use debug keys for pairing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To pave the way for actively using debug keys for pairing this patch
adds a new HCI_USE_DEBUG_KEYS flag for the purpose. When the flag is set
we issue a HCI_Write_SSP_Debug mode whenever HCI_Write_SSP_Mode(0x01)
has been issued as well as before issuing a HCI_Write_SSP_Mode(0x00)
command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should never allow user space to feed back debug keys to the kernel.
If the user desires to use debug keys require setting the appropriate
debug keys mode and performing a new pairing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We're planning to add a flag to actively use debug keys in addition to
simply just accepting them, which makes the current generically named
DEBUG_KEYS flag a bit confusing. Since the flag in practice affects
whether the kernel keeps debug keys around or not rename it to
HCI_KEEP_DEBUG_KEYS.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are two callers of hci_add_link_key(). The first one is the HCI
Link Key Notification event and the second one the mgmt code that
receives a list of link keys from user space. Previously we've had the
hci_add_link_key() function being responsible for also emitting a mgmt
signal but for the latter use case this should not happen. Because of
this a rather awkward new_key paramter has been passed to the function.
This patch moves the mgmt event sending out from the hci_add_link_key()
function, thereby making the code a bit more understandable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All the special settings configured via debugfs are either developer
only options or temporary solutions. To not clutter the standard flags,
move them to their own dbg_flags entry.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The valid range of IO capabilities for the Set IO Capability and Pair
Device mgmt commands is 0-4 (4 being the KeyboarDisplay capability for
SMP). We should return an invalid parameters error if user space gives
us a value outside of this range.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The LTK type has really nothing to do with HCI so it makes more sense to
have these in smp.h than hci.h. This patch moves the defines to smp.h
and removes the HCI_ prefix in the same go.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SMP code expects hdev to be unlocked since e.g. crypto functions
will try to (re)lock it. Therefore, we need to release the lock before
calling into smp.c from mgmt.c. Without this we risk a deadlock whenever
the smp_user_confirm_reply() function is called.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
When cleaning up the HCI state as part of the power-off procedure we can
reuse the hci_stop_discovery() function instead of explicitly sending
HCI command related to discovery. The added benefit of this is that it
takes care of canceling name resolving and inquiry which were not
previously covered by the code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
We'll need to reuse the same logic for stopping discovery also when
cleaning up HCI state when powering off. This patch refactors the code
out to its own function that can later (in a subsequent patch) be used
also for the power off case.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
In case there are new LTK types in the future we shouldn't just blindly
assume that != MGMT_LTK_UNAUTHENTICATED means that the key is
authenticated. This patch adds explicit checks for each allowed key type
in the form of a switch statement and skips any key which has an unknown
value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
On the mgmt level we have a key type parameter which currently accepts
two possible values: 0x00 for unauthenticated and 0x01 for
authenticated. However, in the internal struct smp_ltk representation we
have an explicit "authenticated" boolean value.
To make this distinction clear, add defines for the possible mgmt values
and do conversion to and from the internal authenticated value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are no users of the smp_chan struct outside of smp.c so move it
away from smp.h. The addition of the l2cap.h include to hci_core.c,
hci_conn.c and mgmt.c is something that should have been there already
previously to avoid warnings of undeclared struct l2cap_conn, but the
compiler warning was apparently shadowed away by the mention of
l2cap_conn in the struct smp_chan definition.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
conn_info_age value is calculated in ms, so need to be converted to
jiffies.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for max_tx_power in Get Connection Information
request. Value is read only once for given connection and then always
returned in response as parameter.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
TX power for LE links is immutable thus we do not need to query for it
if already have value.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for Get Connection Information mgmt command
which can be used to query for information about connection, i.e. RSSI
and local TX power level.
In general values cached in hci_conn are returned as long as they are
considered valid, i.e. do not exceed age limit set in hdev. This limit
is calculated as random value between min/max values to avoid client
trying to guess when to poll for updated information.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch increments the management interface revision due to the
changes with the Device Found management event and other fixes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Do not always set the MITM protection requirement by default in the
field conn->auth_type, since this will be added later in
hci_io_capa_request_evt(), as part of the requirements specified in
HCI_OP_IO_CAPABILITY_REPLY.
This avoids a hackish exception for the auto-reject case, but doesn't
change the behavior of the code at all.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To be consistent, lets use msec for this timeout as well.
Note: This define value is a minimum scan time taken from BT Core spec 4.0,
Vol 3, Part C, chapter 9.2.6
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With this patch it is possible to control discovery interleaved
timeout value from debugfs.
It is for fine tuning of this timeout.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Keep msec instead of jiffies in this define. This is needed by following
patch where we want this timeout to be exposed in debugfs.
Note: Value of this timeout comes from recommendation in BT Core Spec.4.0,
Vol 3, Part C, chapter 13.2.1.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The line was incorrectly split between the variable type and its name.
This patch fixes the issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation for being able to merge ADV_IND/ADV_SCAN_IND and SCAN_RSP
together into a single device found event add a second parameter to the
mgmt_device_found function. For now all callers pass NULL as this
parameters since we don't yet have storing of the last received
advertising report.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We need to ensure that we do not send events to user space with the
identity address if we have not yet notified user space of the IRK. The
code was previously trying to handle this for the mgmt_pair_device
response (which worked well enough) but this is not the only connection
related event that might be sent to user space before pairing is
successful: another important event is Device Disconnected.
The issue can actually be solved more simply than the solution
previously used for mgmt_pair_device. Since we do have the identity
address tracked as part of the remote IRK struct we can just copy it
over from there to the hci_conn struct once we've for real sent the mgmt
event for the new IRK.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The passkey_notify and user_confirm functions in mgmt.c were expecting
different endianess for the passkey, leading to a big endian bug and
sparse warning in recently added SMP code. This patch converts both
functions to expect host endianess and do the conversion to little
endian only when assigning to the mgmt event struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It is possible that pairing fails after we've already received remote
identity information. One example of such a situation is when
re-encryption using the LTK fails. In this case the hci_conn object has
already been updated with the identity address but user space does not
yet know about it (since we didn't notify it of the new IRK yet).
To ensure user space doesn't get a Pair Device command response with an
unknown address always use the same address in the response as was used
for the original command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case the pairable option has been disabled, the pairing procedure
does not create keys for bonding. This means that these generated keys
should not be stored persistently.
For LTK and CSRK this is important to tell userspace to not store these
new keys. They will be available for the lifetime of the device, but
after the next power cycle they should not be used anymore.
Inform userspace to actually store the keys persistently only if both
sides request bonding.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The connection signature resolving key (CSRK) is used for attribute
protocol signed write procedures. This change generates a new local
key during pairing and requests the peer key as well.
Newly generated key and received key will be provided to userspace
using the New Signature Resolving Key management event.
The Master CSRK can be used for verification of remote signed write
PDUs and the Slave CSRK can be used for sending signed write PDUs
to the remote device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The debug logs for reporting a discrepancy between the expected amount
of keys and the actually received amount of keys got these value mixed
up. This patch fixes the issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Different controllers behave differently when HCI_Set_Random_Address is
called while they are advertising or have a HCI_LE_Create_Connection in
progress. Some take the newly written address into use for the pending
operation while others use the random address that we had at the time
that the operation started.
Due to this undefined behavior and for the fact that we want to reliably
determine the initiator address of all connections for the sake of SMP
it's best to simply prevent the random address update if we have these
problematic operations in progress.
This patch adds a set_random_addr() helper function for the use of
hci_update_random_address which contains the necessary checks for
advertising and ongoing LE connections.
One extra thing we need to do is to clear the HCI_ADVERTISING flag in
the enable_advertising() function before sending any commands. Since
re-enabling advertising happens by calling first disable_advertising()
and then enable_advertising() all while having the HCI_ADVERTISING flag
set. Clearing the flag lets the set_random_addr() function know that
it's safe to write a new address at least as far as advertising is
concerned.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The random numbers in Bluetooth Low Energy are 64-bit numbers and should
also be little endian since the HCI specification is little endian.
Change the whole Low Energy pairing to use __le64 instead of a byte
array.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If some of the cleanup commands caused by mgmt_set_powered(off) never
complete we should still force the adapter to be powered down. This is
rather easy to do since hdev->power_off is already a delayed work
struct. This patch schedules this delayed work if at least one HCI
command was sent by the cleanup procedure.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When powering off and disconnecting devices we should also consider
connections which have not yet reached the BT_CONNECTED state. They may
not have a valid handle yet and simply sending a HCI_Disconnect will not
work.
This patch updates the code to either disconnect, cancel connection
creation or reject incoming connection creation based on the current
conn->state value as well as the link type in question.
When the power off procedure results in canceling connection attempts
instead of disconnecting connections we get a connection failed event
instead of a disconnection event. Therefore, we also need to have extra
code in the mgmt_connect_failed function to check if we should proceed
with the power off or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to mgmt-api.txt, in case of confirm name command,
cmd_complete should be always use as a response. Not command status
as it is now for failures.
Using command complete on failure is actually better as client might
be interested in device address for which confirm name failed.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If new scanning parameters are set while background scan is running,
we should restart background scanning so these parameters are updated.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should only accept connection parameters from identity addresses
(public or random static). Thus, we should check the address type
in hci_conn_params_add().
Additionally, since the IRK is removed during unpair, we should also
remove the connection parameters from that device.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When hdev is closed (e.g. Mgmt power off command, RFKILL or controller
is reset), the ongoing active connections are silently dropped by the
controller (no Disconnection Complete Event is sent to host). For that
reason, the devices that require HCI_AUTO_CONN_ALWAYS are not added to
hdev->pend_le_conns list and they won't auto connect.
So to fix this issue, during hdev closing, we remove all pending LE
connections. After adapter is powered on, we add a pending LE connection
for each HCI_AUTO_CONN_ALWAYS address.
This way, the auto connection mechanism works propely after a power
off and power on sequence as well as RFKILL block/unblock.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the user sends a mgmt start discovery command while the background
scanning is running, we should temporarily stop it. Once the discovery
finishes, we start the background scanning again.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves address type conversion (L2CAP address type to HCI
address type) to outside hci_connect_le. This way, we avoid back and
forth address type conversion in a comming patch.
So hci_connect_le() now expects 'dst_type' parameter in HCI address
type convention.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_connect() is a very simple and useless wrapper of hci_connect_acl
and hci_connect_le functions. Addtionally, all places where hci_connect
is called the link type value is passed explicitly. This way, we can
safely delete hci_connect, declare hci_connect_acl and hci_connect_le
in hci_core.h and call them directly.
No functionality is changed by this patch.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves stop LE scanning duplicate code to one single
place and reuses it. This will avoid more duplicate code in
upcoming patches.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the connectable setting is toggled using mgmt_set_connectable the
HCI_CONNECTABLE flag will only be set once the related HCI commands
succeed. When determining what kind of advertising to do we need to
therefore also check whether there is a pending Set Connectable command
in addition to the current flag value.
The enable_advertising function was already taking care of this for the
advertising type with the help of the get_adv_type function, but was
failing to do the same for the address type selection. This patch
converts the get_adv_type function to be more generic in that it returns
the expected connectable state and updates the enable_advertising
function to use the return value both for the advertising type as well
as the advertising address type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be friendly to user space and to behave well with controllers that
lack a proper internal power off procedure we should try to clean up as
much state as possible before requesting the HCI driver to power off.
This patch updates the power off procedure that's triggered by
mgmt_set_powered to clean any scan modes, stop LE scanning and
advertising and to disconnect any open connections.
The asynchronous cleanup procedure uses the HCI request framework,
however since HCI_Disconnect is only covered until its Command Status
event we need some extra tracking/waiting of disconnections. This is
done by monitoring when hci_conn_count() indicates that there are no
more connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once mgmt_set_powered(off) is updated to clear the scan mode we should
not just blindly clear the HCI_ADVERTISING flag in mgmt_advertising()
but first check if there is a pending set_powered operation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once mgmt_set_powered(off) is updated to clear the scan mode we should
not just blindly clear the HCI_CONNECTABLE flag in mgmt_connectable()
but first check if there is a pending set_powered operation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once mgmt_set_powered(off) is updated to clear the scan mode we should
not just blindly clear the HCI_DISCOVERABLE flag in mgmt_discoverable()
but first check if there is a pending set_powered operation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once mgmt_set_powered(off) starts doing disconnections we'll need to
care about any disconnections in mgmt.c and not just those with the
MGMT_CONNECTED flag set. Therefore, move the check into mgmt.c from
hci_event.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon need to make decisions on toggling the HCI_ADVERTISING flag
based on pending mgmt_set_powered commands. Therefore, move the handling
from hci_event.c into mgmt.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A user space that supports the Set Privacy command is also expected to
be able to handle New IRK events. Therefore, set the HCI_RPA_RESOLVING
flag whenever the Set Privacy command is received.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When enabling non-connectable advertising, there is no need to advertise
with a public address or static address. In case LE privacy has not been
enabled a unresolvable private address will be used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When running active scanning during LE discovery, do not reveal the own
identity to the peer devices. In case LE privacy has been enabled, then
a resolvable private address is used. If the LE privacy option is off,
then use an unresolvable private address.
The public address or static random address is never used in active
scanning anymore. This ensures that scan request are send using a
random address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds support for handling the Set Privacy mgmt command,
including copying the value to hdev->irk and toggling the HCI_PRIVACY
flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we always update the random address before enabling advertising,
scanning and initiating LE connections there is no need to write the
random address add power on.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we start LE scanning we need to update the local random address if
necessary. This patch updates the code to use hci_update_random_address()
for setting the own_address_type scan parameter and updating the local
random address if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we enable advertising we need to update the local random address if
necessary. This patch takes advantage of the hci_update_random_address()
function to set the own_address_type variable and to update the local
random address if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a timer for updating the local RPA periodically. The
default timeout is set to 15 minutes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes sure that the Privacy flag is available in the mgmt
supported settings for all LE capable controllers and in the current
settings whenever the HCI_PRIVACY flag is set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
