The flash memory for the ice hardware contains a block of information
used for link management called the Netlist module.
As this essentially represents another section of firmware, add its
version information to the output of the driver's .info_get handler.
This includes both a version and the first few bytes of a hash of the
module contents.
fw.netlist -> the version information extracted from the netlist module
fw.netlist.build-> first 4 bytes of the hash of the contents, similar
to fw.mgmt.build
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Oleksij Rempel says:
====================
provide KAPI for SQI
This patches are extending ethtool netlink interface to export Signal
Quality Index (SQI). SQI provided by 100Base-T1 PHYs and can be used for
cable diagnostic. Compared to a typical cable tests, this value can be
only used after link is established.
changes v3:
- rename __ethtool_get_sqi* to linkstate_get_sqi*. And move this
functions to the net/ethtool/linkstate.c
- protect linkstate_get_sqi* with locking
changes v2:
- use u32 instead of u8 for SQI
- add SQI_MAX field and callbacks
- some style fixes in the rst.
- do not convert index to shifted index.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements reading of the Signal Quality Index for better
cable/link troubleshooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Basson says:
====================
qed: Add xrc core support for RoCE
This patch adds support for configuring XRC and provides the necessary
APIs for rdma upper layer driver (qedr) to enable the XRC feature.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for XRC-SRQ's and XRC-QP's for upper layer driver.
We maintain separate bitmaps for resource management for srq and
xrc-srq, However, the range in FW is one, The xrc-srq's are first
and then the srq's follow. Therefore we maintain a srq-id offset.
v2: perform cleanups if XRC bitmpas allocation fail.
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Yuval Bason <ybason@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First ILT page for TSDM client is allocated for XRC-SRQ's.
For regular SRQ's skip first ILT page that is reserved for
XRC-SRQ's.
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Yuval Bason <ybason@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, psample can only send the packet bits after decapsulation.
The tunnel information is lost. Add the tunnel support.
If the sampled packet has no tunnel info, the behavior is the same as
before. If it has, add a nested metadata field named PSAMPLE_ATTR_TUNNEL
and include the tunnel subfields if applicable.
Increase the metadata length for sampled packet with the tunnel info.
If new subfields of tunnel info should be included, update the metadata
length accordingly.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2020-05-19
This series contains updates to igc only.
Sasha cleans up the igc driver code that is not used or needed.
Vitaly cleans up driver code that was used to support Virtualization on
a device that is not supported by igc, so remove the dead code.
Andre renames a few macros to align with register and field names
described in the data sheet. Also adds the VLAN Priority Queue Fliter
and EType Queue Filter registers to the list of registers dumped by
igc_get_regs(). Added additional debug messages and updated return codes
for unsupported features. Refactored the VLAN priority filtering code to
move the core logic into igc_main.c. Cleaned up duplicate code and
useless code.
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro says:
====================
uaccess-related stuff in net/*
Assorted uaccess-related work in net/*. First, there's
getting rid of compat_alloc_user_space() mess in MCAST_...
[gs]etsockopt() - no need to play with copying to/from temporary
object on userland stack, etc., when ->compat_[sg]etsockopt()
instances in question can easly do everything without that.
That's the first 13 patches. Then there's a trivial bit in
net/batman-adv (completely unrelated to everything else) and
finally getting the atm compat ioctls into simpler shape.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
atm_dev_ioctl() does copyin in two different ways - one for
ATM_GETNAMES, another for everything else. Start with separating
the former into a new helper (atm_getnames()). The next step
will be to lift the copyin into the callers.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Native ->setsockopt() handling of these options (MCAST_..._SOURCE_GROUP
and MCAST_{,UN}BLOCK_SOURCE) consists of copyin + call of a helper that
does the actual work. The only change needed for ->compat_setsockopt()
is a slightly different copyin - the helpers can be reused as-is.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
direct parallel to the way these two are handled in the native
->setsockopt() instances - the helpers that do the real work
are already separated and can be reused as-is in this case.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Parallel to what the native setsockopt() does, except that unlike
the native setsockopt() we do not use memdup_user() - we want
the sockaddr_storage fields properly aligned, so we allocate
4 bytes more and copy compat_group_filter at the offset 4,
which yields the proper alignments.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
now we can do MCAST_MSFILTER in compat ->getsockopt() without
playing silly buggers with copying things back and forth.
We can form a native struct group_filter (sans the variable-length
tail) on stack, pass that + pointer to the tail of original request
to the helper doing the bulk of the work, then do the rest of
copyout - same as the native getsockopt() does.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
pass the userland pointer to the array in its tail, so that part
gets copied out by our functions; copyout of everything else is
done in the callers. Rationale: reuse for compat; the array
is the same in native and compat, the layout of parts before it
is different for compat.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We want to get rid of compat_mc_[sg]etsockopt() and to have that stuff
handled without compat_alloc_user_space(), extra copying through
userland, etc. To do that we'll need ipv4 and ipv6 instances of
->compat_[sg]etsockopt() to manipulate the 32bit variants of mcast
requests, so we need to move the definitions of those out of net/compat.c
and into a public header.
This patch just does a mechanical move to include/net/compat.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The conversion to pin_user_pages() had a bug: it overlooked
the case of allocation of pages failing. Fix that by restoring
an equivalent check.
Reported-by: syzbot+118ac0af4ac7f785a45b@syzkaller.appspotmail.com
Fixes: dbfe7d7437 ("rds: convert get_user_pages() --> pin_user_pages()")
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Cc: rds-devel@oss.oracle.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gro_receive() used to be used by SCTP, it is no longer the case.
skb_gro_receive_list() is in the same category : never used from modules.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx data FIFO Head/Tail, Saved and Packet Count registers
not applicable for i225 LAN controller.
This patch comes to clean up these registers.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Device reset assert for interrupt cause register not in
use for i225 device.
This patch comes to clean up this define.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the EType Queue Filter (ETQF) registers to the list of
registers dumped by igc_get_regs().
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The whole ethertype filtering code is implemented in igc_ethtool.c and
mixes logic from ethtool and core parts. This patch refactors it so core
logic is moved to igc_main.c, aligning the ethertype filtering code
organization with the rest of the filtering code from the driver (MAC
address and VLAN priority).
Besides moving code to igc_main.c, this patch also does some minor
improvements to the code. Below are some highlights.
In case all filters are already in use and the user tries to add another
filter, we return -ENOSPC instead of -EINVAL so a more meaningful error
code is provided. This also aligns with the behavior implemented in MAC
address filtering code.
With this code refactoring, 'etype_bitmap' array in struct igc_adapter
and 'etype_reg_index' in struct igc_nfc_filter are not needed anymore
and are removed.
Log messages are added to help debugging the ethertype filtering code.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Christoph Hellwig says:
====================
add a new ->ndo_tunnel_ctl method to avoid a few set_fs calls v2
both the ipv4 and ipv6 code have an ioctl each that can be used to create
a tunnel using code that doesn't live in the core kernel or ipv6 module.
Currently they call ioctls on the tunnel devices to create these, for
which the code needs to override the address limit, which is a "feature"
I plan to get rid of.
Instead this patchset adds a new ->ndo_tunnel_ctl that can be used for
the tunnel configuration using struct ip_tunnel_parm. The method is
either invoked from a helper that does the uaccess and can be wired up
as ndo_do_ioctl method, or directly from the magic IPV4/6 ioctls that
create tunnels with kernel space arguments.
Changes since v2:
- properly propagate errors in ipip6_tunnel_prl_ctl
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new ->ndo_tunnel_ctl instead of overriding the address limit
and using ->ndo_do_ioctl just to do a pointless user copy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out a addrconf_set_sit_dstaddr helper for the actual work if we
found a SIT device, and only hold the rtnl lock around the device lookup
and that new helper, as there is no point in holding it over a
copy_from_user call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in copying the structure from userspace or looking up
a device if SIT support is not disabled and we'll eventually return
-ENODEV anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the ->ndo_tunnel_ctl method, and use ip_tunnel_ioctl to
handle userspace requests for the SIOCGETTUNNEL, SIOCADDTUNNEL,
SIOCCHGTUNNEL and SIOCDELTUNNEL ioctls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the ioctl handler into one function per command instead of having
a all the logic sit in one giant switch statement.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new ->ndo_tunnel_ctl instead of overriding the address limit
and using ->ndo_do_ioctl just to do a pointless user copy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This method is used to properly allow kernel callers of the IPv4 route
management ioctls. The exsting ip_tunnel_ioctl helper is renamed to
ip_tunnel_ctl to better reflect that it doesn't directly implement ioctls
touching user memory, and is used for the guts of ndo_tunnel_ctl
implementations. A new ip_tunnel_ioctl helper is added that can be wired
up directly to the ndo_do_ioctl method and takes care of the copy to and
from userspace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also move the dev_set_allmulti call and the error handling into the
ioctl helper. This allows reusing already looked up tunnel_dev pointer
and the set up argument structure for the deletion in the error handler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce a few level of indentation to simplify the function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The I225 controller has 8 ethertype filters, not 4. This patch fixes the
MAX_ETYPE_FILTER macro accordingly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver only supports hardware timestamping for all incoming
traffic (HWTSTAMP_FILTER_ALL) which is enabled via Rx Time Sync
Control (TSYNCRXCTL) register already. Therefore, the ethertype
filter set in in igc_ptp_set_timestamp_mode() is useless so this
patch removes it.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch remove the IGC_RXPBS macro defined in line 233 since it is
already defined in line 18 with the exactly same value.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Vaibhav Gupta says:
====================
realtek ethernet : use generic power management.
The purpose of this patch series is to remove legacy power management callbacks
from realtek ethernet drivers.
The callbacks performing suspend() and resume() operations are still calling
pci_save_state(), pci_set_power_state(), etc. and handling the powermanagement
themselves, which is not recommended.
The conversion requires the removal of the those function calls and change the
callback definition accordingly.
All Changes are compile-tested only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
compile-tested only
With legacy PM hooks, it was the responsibility
of a driver to manage PCI states and also
device's power state. The generic approach is
to let PCI core handle the work.
The suspend callback enables/disables PCI wake
on the basis of "cp->wol_enabled" variable
which is unknown to PCI core. To utilise its
need, call device_set_wakeup_enable().
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
