SPI NOR chips are made of pages, which gathered in small groups make
(erase) sectors. Sectors, gathered together, make banks inside the
chip. Until now, there was only one bank per device supported, but we
are about to introduce support for new chips featuring several banks (up
to 4 so far) where different operations may happen in parallel.
Let's allow describing these additional bank parameters, and let's do
this independently of any other value (like the number of sectors) with
an absolute value.
By default we consider that all chips have a single bank.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20230328154105.448540-2-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
struct class should never be modified in a sysfs callback as there is
nothing in the structure to modify, and frankly, the structure is almost
never used in a sysfs callback, so mark it as constant to allow struct
class to be moved to read-only memory.
While we are touching all class sysfs callbacks also mark the attribute
as constant as it can not be modified. The bonding code still uses this
structure so it can not be removed from the function callbacks.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Russ Weight <russell.h.weight@intel.com>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Steve French <sfrench@samba.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-cifs@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-rdma@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: netdev@vger.kernel.org
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20230325084537.3622280-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clang with W=1 reports
drivers/mtd/lpddr/lpddr_cmds.c:409:31: error: variable
'words' set but not used [-Werror,-Wunused-but-set-variable]
int ret, wbufsize, word_gap, words;
^
This variable is not used so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230328000620.1778033-1-trix@redhat.com
clang with W=1 reports
drivers/mtd/nand/raw/mxc_nand.c:1602:19: error: unused function
'is_imx51_nfc' [-Werror,-Wunused-function]
static inline int is_imx51_nfc(struct mxc_nand_host *host)
^
drivers/mtd/nand/raw/mxc_nand.c:1607:19: error: unused function
'is_imx53_nfc' [-Werror,-Wunused-function]
static inline int is_imx53_nfc(struct mxc_nand_host *host)
^
These functions are not used, so remove them.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230321114638.1782086-1-trix@redhat.com
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230310144715.1543926-1-robh@kernel.org
According to the ONFI specification, bit 0 of 'SDR timing mode support'
(bytes 129-130) "shall be 1". That means the NAND supports at least
timing mode 0.
NAND chip Hynix H27U4G8F2GDA-BI (at least) is reading a 0 on this field
which makes nand_choose_best_sdr_timings() return with error and the
probe function to eventually fail.
Given that sdr_timing_modes bit 0 must be 1 by specification, force
it in case the NAND reports it is not set. This is a safe assumption
because the mode 0 is the minimum (safer) set of timings that the
NAND can work with.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230223165104.525852-1-hector.palacios@digi.com
Link: https://lore.kernel.org/linux-mtd/20230310080609.1930869-1-hector.palacios@digi.com
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230310144716.1543995-1-robh@kernel.org
'info_buf' memory is cached and driver polls ECC bit in it. This bit
is set by the NAND controller. If 'usleep_range()' returns before device
sets this bit, 'info_buf' will be cached and driver won't see update of
this bit and will loop forever.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/d4ef0bd6-816e-f6fa-9385-f05f775f0ae2@sberdevices.ru
The continuous read support added recently makes nandsim
unhappy. Indeed, all the supported commands should be re-encoded into
internal commands, so of course there is currently no support for the
commands and patterns needed for continuous reads to work.
I tried to add support for them but nandsim (which is more a tool to
develop/debug upper layers rather than the raw NAND core) suffers from a
big limitation: it's internal parser needs to know what exact operation
is happening when the address cycles are performed. The research is then
sequential from the start up to the address cycles, but does not check
what's coming next even though the information is available. This is a
limitation which is related to the old API used by the core which kind
of forced the controllers to guess what operation was being performed
rather early. Today the core uses a more transparent API called
->exec_op() which no longer requires controller drivers to do any more
guessing, but despite being updated to ->exec_op(), nandsim is still a
bit constrained on this regard and thus cannot handle sequential page
reads because the start sequence beginning is identical to a regular
page read.
If the internal algorithm is updated some day, it should be possible to
make it support sequential page reads by adding something like:
/* Large page devices continuous read page start */
{OPT_LARGEPAGE, {STATE_CMD_READ0, STATE_ADDR_PAGE, STATE_CMD_READSTART,
STATE_CMD_READCACHESEQ | ACTION_CPY, STATE_DATAOUT,
STATE_READY}},
/* Large page devices continuous read page continue */
{OPT_LARGEPAGE, {STATE_CMD_READCACHESEQ | ACTION_CPY_NEXT, STATE_DATAOUT,
STATE_READY}},
/* Large page devices continuous read page end */
{OPT_LARGEPAGE, {STATE_CMD_READCACHEEND | ACTION_CPY_NEXT, STATE_DATAOUT,
STATE_READY}},
For now, we just return -EOPNOTSUPP when the core asks controller
drivers if they support the feature in order to prevent any further use
of these opcodes.
Note: This is a hack, ->exec_op() is not supposed to check against the
COMMAND opcodes unless _really_ needed.
Fixes: 003fe4b954 ("mtd: rawnand: Support for sequential cache reads")
Reported-by: Zhihao Cheng <chengzhihao1@huawei.com>
Link: https://lore.kernel.org/linux-mtd/fd34fe55-7f4a-030d-8653-9bb9cf08410d@huawei.com/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Zhihao Cheng <chengzhihao1@huawei.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/linux-mtd/20230310085452.1368716-1-miquel.raynal@bootlin.com
There is no need to manually set the owner of a struct class, as the
registering function does it automatically, so remove all of the
explicit settings from various drivers that did so as it is unneeded.
This allows us to remove this pointer entirely from this structure going
forward.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230313181843.1207845-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently Read Any Register op is used to read volatile registers without
any dummy cycles, but the op requires dummy cycles depending on register
type (volatiler or non-volatile), device family, and device configuration.
Add 'ndummy' argument to RD_ANY_REG_OP macro to support other use cases.
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/03756e9e3ac41d2016a71d2afb702398dd0b19ed.1677557525.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
* final coversions of drivers away from deprecated .probe
* make .probe_new the standard probe and convert I2C core to use it
-----BEGIN PGP SIGNATURE-----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=jm/G
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This marks the end of a transition to let I2C have the same probe
semantics as other subsystems. Uwe took care that no drivers in the
current tree nor in -next use the deprecated .probe call. So, it is a
good time to switch to the new, standard semantics now.
There is also a regression fix:
- regression fix for the notifier handling of the I2C core
- final coversions of drivers away from deprecated .probe
- make .probe_new the standard probe and convert I2C core to use it
* tag 'i2c-for-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: dev: Fix bus callback return values
i2c: Convert drivers to new .probe() callback
i2c: mux: Convert all drivers to new .probe() callback
i2c: Switch .probe() to not take an id parameter
media: i2c: ov2685: convert to i2c's .probe_new()
media: i2c: ov5695: convert to i2c's .probe_new()
w1: ds2482: Convert to i2c's .probe_new()
serial: sc16is7xx: Convert to i2c's .probe_new()
mtd: maps: pismo: Convert to i2c's .probe_new()
misc: ad525x_dpot-i2c: Convert to i2c's .probe_new()
Switching to BLK_MQ_F_BLOCKING wrongly removed the call to
blk_mq_end_request(). Add it back to have our IOs finished
Fixes: 91cc8fbcc8 ("ubi: block: set BLK_MQ_F_BLOCKING")
Analyzed-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/linux-mtd/CAHk-=wi29bbBNh3RqJKu3PxzpjDN5D5K17gEVtXrb7-6bfrnMQ@mail.gmail.com/
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Supporting multi-cs in spi drivers would require the chip_select & cs_gpiod
members of struct spi_device to be an array. But changing the type of these
members to array would break the spi driver functionality. To make the
transition smoother introduced four new APIs to get/set the
spi->chip_select & spi->cs_gpiod and replaced all spi->chip_select and
spi->cs_gpiod references with get or set API calls.
While adding multi-cs support in further patches the chip_select & cs_gpiod
members of the spi_device structure would be converted to arrays & the
"idx" parameter of the APIs would be used as array index i.e.,
spi->chip_select[idx] & spi->cs_gpiod[idx] respectively.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/167847071245.26.7777775616228465939@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/lkml/20221118224540.619276-497-uwe@kleine-koenig.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Nvmem producer config ID "-1" is actually defined, so use the definition
rather than hardcoding it with a magic value.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/linux-mtd/20230307192536.470997-1-miquel.raynal@bootlin.com
* Prepare mtd_otp_nvmem_add() to handle -EPROBE_DEFER
* Fix error path for nvmem provider
* Fix nvmem error reporting
* Provide unique name for nvmem device
These changes are expected to be pulled before applying nvmem layouts
support in order to get a fully working support in all situations.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmQIkRoACgkQJWrqGEe9
VoR0vwf/ZkhNer2rVnC7S47P4Lvw5KHMt7p7cM2no3obM2A3JYi2qrRRw3e3RkZq
CboUOKqjbKgQ+WxLnj18M9MqPac+rSKiU28Ji+Cx3x0yycubFRWewYH+vZ3VNdP8
w/sO1+uBp7rkL9fa2lR1ZmBqCFAXLI2fglhV09JQuOH+VJHe1XVQOBfrJrSwU8Ne
rxlSndEew5vldQA1nDOP4BqXKaiYoLbaLuig8y17nEJ+d1MvN8NVzBqwAWVKgihn
0zsD5s+ew9BGZ5JmUwn0QmkAbX9HrQEMLERA7shixaZ4DHwK84HRgOGX6cr01fV6
AHZx7svX11rSEUf5rng2UlClOSCoXg==
=Is2Q
-----END PGP SIGNATURE-----
Merge tag 'mtd/core-fixes-before-nvmem-layouts-for-6.4' into mtd/next
Core MTD changes:
* Prepare mtd_otp_nvmem_add() to handle -EPROBE_DEFER
* Fix error path for nvmem provider
* Fix nvmem error reporting
* Provide unique name for nvmem device
These changes are expected to be pulled before applying nvmem layouts
support in order to get a fully working support in all situations.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since commit 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230224150811.80316-19-nick.alcock@oracle.com
NVMEM soon will get the ability for nvmem layouts and these might
not be ready when nvmem_register() is called and thus it might
return -EPROBE_DEFER. Don't print the error message in this case.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230308082021.870459-4-michael@walle.cc
If mtd_otp_nvmem_add() fails, the partitions won't be removed
because there is simply no call to del_mtd_partitions().
Unfortunately, add_mtd_partitions() will print all partitions to
the kernel console. If mtd_otp_nvmem_add() returns -EPROBE_DEFER
this would print the partitions multiple times to the kernel
console. Instead move mtd_otp_nvmem_add() to the beginning of the
function.
Fixes: 4b361cfa86 ("mtd: core: add OTP nvmem provider support")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230308082021.870459-3-michael@walle.cc
The master MTD will only have an associated device if
CONFIG_MTD_PARTITIONED_MASTER is set, thus we cannot use dev_err() on
mtd->dev. Instead use the parent device which is the physical flash
memory.
Fixes: 4b361cfa86 ("mtd: core: add OTP nvmem provider support")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230308082021.870459-2-michael@walle.cc
Commit c048b60d39 ("mtd: core: provide unique name for nvmem device")
tries to give the nvmem device a unique name, but fails badly if the mtd
device doesn't have a "struct device" associated with it, i.e. if
CONFIG_MTD_PARTITIONED_MASTER is not set. This will result in the name
"(null)-user-otp", which is not unique. It seems the best we can do is
to use the compatible name together with a unique identifier added by
the nvmem subsystem by using NVMEM_DEVID_AUTO.
Fixes: c048b60d39 ("mtd: core: provide unique name for nvmem device")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230308082021.870459-1-michael@walle.cc
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230306144141.15360-1-quic_mdalam@quicinc.com
wait_for_completion_timeout() and readl_poll_timeout() don't handle their
return value the same way.
wait_for_completion_timeout() returns 0 on time out (and >0 in all other
cases)
readl_poll_timeout() returns 0 on success and -ETIMEDOUT upon a timeout.
In order for the error handling path to work in both cases, the logic
against wait_for_completion_timeout() needs to be inverted.
Fixes: 48e6633a9f ("mtd: nand: mxic-ecc: Add Macronix external ECC engine support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/beddbc374557e44ceec897e68c4a5d12764ddbb9.1676459308.git.christophe.jaillet@wanadoo.fr
This structure must be zeroed, because it's field 'hw->core' is used as
'parent' in 'clk_core_fill_parent_index()', but it will be uninitialized.
This happens, because when this struct is not zeroed, pointer 'hw' is
"initialized" by garbage, which is valid pointer, but points to some
garbage. So 'hw' will be dereferenced, but 'core' contains some random
data which will be interpreted as a pointer. The following backtrace is
result of dereference of such pointer:
[ 1.081319] __clk_register+0x414/0x820
[ 1.085113] devm_clk_register+0x64/0xd0
[ 1.088995] meson_nfc_probe+0x258/0x6ec
[ 1.092875] platform_probe+0x70/0xf0
[ 1.096498] really_probe+0xc8/0x3e0
[ 1.100034] __driver_probe_device+0x84/0x190
[ 1.104346] driver_probe_device+0x44/0x120
[ 1.108487] __driver_attach+0xb4/0x220
[ 1.112282] bus_for_each_dev+0x78/0xd0
[ 1.116077] driver_attach+0x2c/0x40
[ 1.119613] bus_add_driver+0x184/0x240
[ 1.123408] driver_register+0x80/0x140
[ 1.127203] __platform_driver_register+0x30/0x40
[ 1.131860] meson_nfc_driver_init+0x24/0x30
Fixes: 1e4d3ba668 ("mtd: rawnand: meson: fix the clock")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230227102425.793841-1-AVKrasnov@sberdevices.ru
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_ioremap_resource(), as this is exactly what this
function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/202302101723563685569@zte.com.cn
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To solve this, remove the
lookup and create the directory on the first device found, and then
remove it when the module is unloaded.
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Pratyush Yadav <pratyush@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230208160230.2179905-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the processing of the bgt, if the sync_erase() return -EBUSY
or some other error code in __erase_worker(),schedule_erase() called
again lead to the down_read(ubi->work_sem) hold twice and may get
block by down_write(ubi->work_sem) in ubi_update_fastmap(),
which cause deadlock.
ubi bgt other task
do_work
down_read(&ubi->work_sem) ubi_update_fastmap
erase_worker # Blocked by down_read
__erase_worker down_write(&ubi->work_sem)
schedule_erase
schedule_ubi_work
down_read(&ubi->work_sem)
Fix this by changing input parameter @nested of the schedule_erase() to
'true' to avoid recursively acquiring the down_read(&ubi->work_sem).
Also, fix the incorrect comment about @nested parameter of the
schedule_erase() because when down_write(ubi->work_sem) is held, the
@nested is also need be true.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217093
Fixes: 2e8f08deab ("ubi: Fix races around ubi_refill_pools()")
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
JFFS2:
- Fix memory corruption in error path
- Spelling and coding style fixes
UBI:
- Switch to BLK_MQ_F_BLOCKING in ubiblock
- Wire up partent device (for sysfs)
- Multiple UAF bugfixes
- Fix for an infinite loop in WL error path
UBIFS:
- Fix for multiple memory leaks in error paths
- Fixes for wrong space accounting
- Minor cleanups
- Spelling and coding style fixes
-----BEGIN PGP SIGNATURE-----
iQJKBAABCAA0FiEEdgfidid8lnn52cLTZvlZhesYu8EFAmP/BSMWHHJpY2hhcmRA
c2lnbWEtc3Rhci5hdAAKCRBm+VmF6xi7wX5QEADnPsAW87AIi44UlkbAsJEjkEqU
yQrI9UPsdqfE7K5OR7Vb2tOti3MLfaiJ5MTG64xNaTEgmrbcqo4GgENk4Pe6zJ9q
azO/xWTr6r8G4aE70KhsUBc9Vc/99Ok48rxLHJS+u7s+FvOJ//WirGXjyNZEVDyx
TgvH80rhUlfj1ExqEXLcUfQ53WUnR3PefOw+zIi29ldtgaI/TFmnWObl2A/XtsGr
0ExIdqDnoTfSsYecfGP71jVbYH8u2mLFe2zNOYW1pvrHYhcet6Q6e+69fgnyNRf9
5s5dbDPmmWN2Qdz63AWwHfC4mncoQdc7HbnnKIk6bTm3v6gqXQSrgy/hZEX3LmWr
G41j7RLhBMZ2mljRfFQH97V71n9TL010T6jZ5zurvqErXtVdFImmInGmqY3AR13I
fzUWnJf81xKgcMv6My2/nEVGDtrGLFdILoT8j6VIXQO6teqtF7Vip7UfamrwL399
57fy0Iwbx2aume/IdwI3TZYacBQ2d8GvQxTZshJ+qx+gCvhb6EyiSIn3AOgtrbAo
srXMy+6xXJecKNHR7Bl1C5BLei/25HDIYjk/yiAH/IhhV20c5eiySSvA+q720Gcz
reBLFh7EtcP51B2GXMdSCOgYY8wGaMl5zlbiLYzY79ptgnnBJ7luuYjc3c02MGB9
25qVLnpvC/ZREzZqLg==
=fTYq
-----END PGP SIGNATURE-----
Merge tag 'ubifs-for-linus-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull jffs2, ubi and ubifs updates from Richard Weinberger:
"JFFS2:
- Fix memory corruption in error path
- Spelling and coding style fixes
UBI:
- Switch to BLK_MQ_F_BLOCKING in ubiblock
- Wire up partent device (for sysfs)
- Multiple UAF bugfixes
- Fix for an infinite loop in WL error path
UBIFS:
- Fix for multiple memory leaks in error paths
- Fixes for wrong space accounting
- Minor cleanups
- Spelling and coding style fixes"
* tag 'ubifs-for-linus-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs: (36 commits)
ubi: block: Fix a possible use-after-free bug in ubiblock_create()
ubifs: make kobj_type structures constant
mtd: ubi: block: wire-up device parent
mtd: ubi: wire-up parent MTD device
ubi: use correct names in function kernel-doc comments
ubi: block: set BLK_MQ_F_BLOCKING
jffs2: Fix list_del corruption if compressors initialized failed
jffs2: Use function instead of macro when initialize compressors
jffs2: fix spelling mistake "neccecary"->"necessary"
ubifs: Fix kernel-doc
ubifs: Fix some kernel-doc comments
UBI: Fastmap: Fix kernel-doc
ubi: ubi_wl_put_peb: Fix infinite loop when wear-leveling work failed
ubi: Fix UAF wear-leveling entry in eraseblk_count_seq_show()
ubi: fastmap: Fix missed fm_anchor PEB in wear-leveling after disabling fastmap
ubifs: ubifs_releasepage: Remove ubifs_assert(0) to valid this process
ubifs: ubifs_writepage: Mark page dirty after writing inode failed
ubifs: dirty_cow_znode: Fix memleak in error handling path
ubifs: Re-statistic cleaned znode count if commit failed
ubi: Fix permission display of the debugfs files
...
As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmPtSN8ACgkQmmx57+YA
GNkOSw/+JS5tElm/ZP7c3uWYp6uwvcb0jUlKW/U3aCtPiPEcYDLEqIEXwcNdaDMh
m4rW3GYlW0IRL3FsyuYkSLx+EIIUIfs40wldYXJOqRDj0XasndiloIwltOQJGfd9
C/UVM0FpJdxMJrcBMFgwLLQCIbAVnhHP34i6ppDRgxW/MfTeiCaaG6fnS70iv6mC
oh2N7FoZSKDtTrFtlR5TqFiK5v/W1CgNJVuglkFB0ceFpjyBpp/8AT0FGS887xCz
IYSTqm4Q/79vaZXI1Y2oog257cgdwsVqgPrnK5CuSFhTnAcJMCekiFelHq8Yhyuk
Rw7j/B3KO3AOaxmR75c6SZdeZ+VHgUMRC/RKe3fay0sm3Zea2kAIPXA6Zn+r/cxb
8M94V59qBz+f8XmpXRTK1UR3s3EbwFIuNyuDIkeorMtpSKtvqJXmZxGDwNIfXr2F
/voo++MKjzdtdxdW/D/5Tc9DC0Pyb4HLi0EYj2QCzA03njmfLDF1w73NfzMec+GD
R1zAd3FEbiJQx8Hin0PSPjYXpfMnkjkGAEcE9N9Ralg4ewNWAxfOFsAhHKTZNssL
pitTAvHR/+dXtvkX7FUi2l/6fqn8nJUrg/xRazPPp3scRbpuk8m6P4MNr3/lsaHk
HTQ/hYwDdecWLvKXjw5y9yIr3yhLmPPcloTVIIFFjsM0t8b+d9E=
=p6Xp
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv"
* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
power: supply: Introduce Qualcomm PMIC GLINK power supply
soc: apple: rtkit: Do not copy the reg state structure to the stack
soc: sunxi: SUN20I_PPU should depend on PM
memory: renesas-rpc-if: Remove redundant division of dummy
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
...
* parsers: ofpart: add workaround for #size-cells 0
* dt-bindings: partitions: Fix partition node name pattern
* dataflash: remove duplicate SPI ID table
Raw NAND core changes:
* Check the data only read pattern only once
* Prepare the late addition of supported operation checks
* Support for sequential cache reads
* Fix nand_chip kdoc
Raw NAND driver changes:
* Fsl_elbc: Propagate HW ECC settings to HW
* Marvell: Add missing layouts
* Pasemi: Don't use static data to track per-device state
* Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
* tmio_nand: Remove driver
* vf610_nfc: Use regular comments for functions
SPI-NAND driver changes:
* Add support for AllianceMemory AS5F34G04SND
* Macronix: use scratch buffer for DMA operation
NAND ECC changes:
* Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
SPI NOR changes:
* Misc core fixes
SPI NOR driver changes:
* Spansion: Minor fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmP3MqwACgkQJWrqGEe9
VoTnsQf/bfzBqf0LbMBU7c+2VUjnE2dgLRssf0WqJB2INvDIAHQ8HKE2rqF6j1G0
wBnJOMf9fRpH6M3k45siNL37HPnacUq8QFZE3B3A3pUewWNtx5ldFrzT1awlsTu8
zIG37pnd2rJ+W3wfDDnNjTqQUfm3sLI7k/B3S8aqJA8i63DFLqih7ju0mgPVT7TX
C1X0VAx8gNMHQ6WqTX53SRZ4Ef9dJAcVwcFhkjHY09Q9VEW56ZlQ7uxyhwYqXjiJ
zDDGfPFhAsfwcykdFI3DtvNRT2bVbJl7N4GvTD8N4Rf+GIuMhVJnUjp5yTkAeEHx
HjXqBSI3ykHimsW7BRtE3HLR4775bA==
=FLt2
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD changes:
- parsers: ofpart: add workaround for #size-cells 0
- dt-bindings: partitions: Fix partition node name pattern
- dataflash: remove duplicate SPI ID table
Raw NAND core changes:
- Check the data only read pattern only once
- Prepare the late addition of supported operation checks
- Support for sequential cache reads
- Fix nand_chip kdoc
Raw NAND driver changes:
- Fsl_elbc: Propagate HW ECC settings to HW
- Marvell: Add missing layouts
- Pasemi: Don't use static data to track per-device state
- Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
- tmio_nand: Remove driver
- vf610_nfc: Use regular comments for functions
SPI-NAND driver changes:
- Add support for AllianceMemory AS5F34G04SND
- Macronix: use scratch buffer for DMA operation
NAND ECC changes:
- Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
SPI NOR changes:
- Misc core fixes
SPI NOR driver changes:
- Spansion: Minor fixes"
* tag 'mtd/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (33 commits)
mtd: parsers: ofpart: add workaround for #size-cells 0
mtd: rawnand: sunxi: Precompute the ECC_CTL register value
mtd: rawnand: sunxi: Embed sunxi_nand_hw_ecc by value
mtd: rawnand: sunxi: Update OOB layout to match hardware
mtd: spi-nor: Sort headers alphabetically
mtd: spi-nor: Fix shift-out-of-bounds in spi_nor_set_erase_type
mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC
dt-bindings: mtd: mediatek,nand-ecc-engine: Add compatible for MT7986
dt-bindings: mtd: Split ECC engine with rawnand controller
mtd: rawnand: fsl_elbc: Propagate HW ECC settings to HW
mtd: spinand: Add support for AllianceMemory AS5F34G04SND
dt-bindings: mtd: partitions: Fix partition node name pattern
mtd: spi-nor: Create macros to define chip IDs and geometries
mtd: spi-nor: spansion: Make CFRx reg fields generic
mtd: spi-nor: spansion: Consider reserved bits in CFR5 register
mtd: spi-nor: core: fix implicit declaration warning
mtd: spinand: macronix: use scratch buffer for DMA operation
mtd: rawnand: Fix nand_chip kdoc
mtd: rawnand: vf610_nfc: use regular comments for functions
mtd: rawnand: Support for sequential cache reads
...
Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work falls
into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be moved
into read-only memory (i.e. const) The recent work with Rust has
pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only making
things safer overall. This is the contuation of that work (started
last release with kobject changes) in moving struct bus_type to be
constant. We didn't quite make it for this release, but the
remaining patches will be finished up for the release after this
one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/ipdg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynL3gCgwzbcWu0So3piZyLiJKxsVo9C2EsAn3sZ9gN6
6oeFOjD3JDju3cQsfGgd
=Su6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
* Check the data only read pattern only once
* Prepare the late addition of supported operation checks
* Support for sequential cache reads
* Fix nand_chip kdoc
Raw NAND changes:
* Fsl_elbc: Propagate HW ECC settings to HW
* Marvell: Add missing layouts
* Pasemi: Don't use static data to track per-device state
* Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
* tmio_nand: Remove driver
* vf610_nfc: Use regular comments for functions
SPI-NAND changes:
* Add support for AllianceMemory AS5F34G04SND
* Macronix: use scratch buffer for DMA operation
NAND ECC changes:
* Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmP3L4MACgkQJWrqGEe9
VoSVKgf+PUOBlR6U/QaNlzavYsTOz1Hgc9MjuC32CtStED8/uKfEG9odBRw1Fp+I
fNpgVnaWrU7KpW9yzsMTLQy//6lI/Hjn4KUMqKcsBmN3dOvzca60YrbehWLlrARb
exRDFvwuw6qZ0jRYMsKC9jsKhvU69TXnAWCdC+TSWRwfXci5dfjm3HxMNpRvT+PQ
q3sWqFMGj+omLOr/R+sBzhSV0WU1FpQsG9NB6I0VbFiJGy9YMMaI2tr/TKJyYeqM
CM0T3tccjKAajJ9i9qKIPZnRYWQYx/FyJ5Uyg6DRxjeoVjsFhGom1pQbH/2eHVs6
iND3n1yQCsnPaR/D7yRZgiTERQzqdw==
=psZR
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.3' into mtd/next
NAND core changes:
* Check the data only read pattern only once
* Prepare the late addition of supported operation checks
* Support for sequential cache reads
* Fix nand_chip kdoc
Raw NAND changes:
* Fsl_elbc: Propagate HW ECC settings to HW
* Marvell: Add missing layouts
* Pasemi: Don't use static data to track per-device state
* Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
* tmio_nand: Remove driver
* vf610_nfc: Use regular comments for functions
SPI-NAND changes:
* Add support for AllianceMemory AS5F34G04SND
* Macronix: use scratch buffer for DMA operation
NAND ECC changes:
* Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
* small fixes on core and spansion driver.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmPgyGUACgkQS1VPR6WN
FOkv+AgAmqp68REEM7SicPy2dIy6fdLFOLjma9CSiWwGTMEJRM60ZBNFCJcAuUjD
1Sf+TCZEkBHc2crYCun5SqBErOA9oQCxI4nVtKZEQ9RyBklz/e5DsLONsVlLKrJU
lwemyeZ2tAV8023iBdjCi1nJ831eRmYipQMIEvr2xbOP/G95Ccc/wG6vKeMDi2QR
BxWdPD4XXvIVRY923nvnz9kK65QiqEQASJ8Rpf/AIYw+C/oukQFql8J3SMMs9kLH
DLagTnyhTx8qMd0V7Z6OVA3Ljf+bMd5gI7Z2fFQhErKo1mvT1Jw13sDQwxGGs+XS
9yxomEDKX+d/LdWEoZaSWFYwHVEixQ==
=fazc
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.3' into mtd/next
SPI NOR changes:
* small fixes on core and spansion driver.
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate subsystem
trees, but the majority is in the same branch, in order to better handle
dependencies between the patches and avoid breaking bisection.
Unfortunately that leads to merge conflicts against other changes in the
subsystem trees, but they should all be trivial to resolve by removing
the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed. The
only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users.
-----BEGIN PGP SIGNATURE-----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=WejQ
-----END PGP SIGNATURE-----
Merge tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
Smatch warns:
drivers/mtd/ubi/block.c:438 ubiblock_create()
warn: '&dev->list' not removed from list
'dev' is freed in 'out_free_dev:, but it is still on the list.
To fix this, delete the list item before freeing.
Fixes: 91cc8fbcc8 ("ubi: block: set BLK_MQ_F_BLOCKING")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
ubiblock devices were previously only identifyable by their name, but
not connected to their parent UBI volume device e.g. in sysfs.
Properly parent ubiblock device as descendant of a UBI volume device
to reflect device model hierachy.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Wire up the device parent pointer of UBI devices to their lower MTD
device, typically an MTD partition or whole-chip device.
The most noticeable change is that in sysfs, previously ubi devices
would be could in /sys/devices/virtual/ubi while after this change they
would be correctly attached to their parent MTD device, e.g.
/sys/devices/platform/1100d000.spi/spi_master/spi1/spi1.0/mtd/mtd2/ubi0.
Locating UBI devices using /sys/class/ubi/ of course still works as
well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
These "nvmem-cells" platform devices never get probed because there's no
platform driver for it and it's never used anywhere else. So it's a
waste of memory. These devices also cause fw_devlink to block nvmem
consumers of "nvmem-cells" partition from probing because the supplier
device never probes.
So stop creating platform devices for nvmem-cells partitions to avoid
wasting memory and to avoid blocking probing of consumers.
Reported-by: Maxim Kiselev <bigunclemax@gmail.com>
Fixes: bcdf0315a6 ("mtd: call of_platform_populate() for MTD partitions")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Maksim Kiselev <bigunclemax@gmail.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # qcom/sm7225-fairphone-fp4
Link: https://lore.kernel.org/r/20230207014207.1678715-13-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a mechanism to handle the case in which partitions are present as
direct child of the nand controller node and #size-cells is set to <0>.
This could happen if the nand-controller node in the DTS is supposed to
have #size-cells set to 0, but for some historical reason/bug it was set
to 1 in the past, and the firmware (e.g. U-Boot) is adding the partition
as direct children of the nand-controller defaulting to #size-cells
being to 1.
This prevents a real boot failure on colibri-imx7 that happened during v6.1
development cycles.
Link: https://lore.kernel.org/all/Y4dgBTGNWpM6SQXI@francesco-nb.int.toradex.com/
Link: https://lore.kernel.org/all/20221202071900.1143950-1-francesco@dolcini.it/
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230124104444.330913-1-francesco@dolcini.it
The value computed by this function never changes for a given chip.
Compute the whole register value once up front, instead of every time
the ECC engine is enabled.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230204143520.9682-4-samuel@sholland.org
The sunxi_nand_hw_ecc object is not shared, and it has the same lifetime
as the sunxi_nand_chip which points to it, so we can embed it in the
outer structure instead of using a pointer. This removes an unnecessary
memory allocation and simplifies the error handling code.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230204143520.9682-3-samuel@sholland.org
When using the hardware ECC engine, the OOB data is made available in
the NFC_REG_USER_DATA registers, as one 32-bit word per ECC step. Any
additional bytes are only accessible through raw reads and software
descrambling. For efficiency, and to match the vendor driver, ignore
these extra bytes when using hardware ECC.
Note that until commit 34569d8695 ("mtd: rawnand: sunxi: Fix the size
of the last OOB region"), this extra free area was reported with length
zero, so this is not a functional change for any stable kernel user.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230204143520.9682-2-samuel@sholland.org
Sort headers alphabetically - it helps locating duplicates, and makes it
easier to figure out where to insert new headers. Alphabetic order should
also prove that each header is self-contained, i.e. can be included without
prerequisites.
Link: https://lore.kernel.org/r/20230202144628.14443-1-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
spi_nor_set_erase_type() was used either to set or to mask out an erase
type. When we used it to mask out an erase type a shift-out-of-bounds
was hit:
UBSAN: shift-out-of-bounds in drivers/mtd/spi-nor/core.c:2237:24
shift exponent 4294967295 is too large for 32-bit type 'int'
The setting of the size_{shift, mask} and of the opcode are unnecessary
when the erase size is zero, as throughout the code just the erase size
is considered to determine whether an erase type is supported or not.
Setting the opcode to 0xFF was wrong too as nobody guarantees that 0xFF
is an unused opcode. Thus when masking out an erase type, just set the
erase size to zero. This will fix the shift-out-of-bounds.
Fixes: 5390a8df76 ("mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories")
Cc: stable@vger.kernel.org
Reported-by: Alexander Stein <Alexander.Stein@tq-group.com>
Signed-off-by: Louis Rannou <lrannou@baylibre.com>
Tested-by: Alexander Stein <Alexander.Stein@tq-group.com>
Link: https://lore.kernel.org/r/20230203070754.50677-1-tudor.ambarus@linaro.org
[ta: refine changes, new commit message, fix compilation error]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Fix kernel-doc warnings by using the correct function names in
their kernel-doc notation:
drivers/mtd/ubi/eba.c:72: warning: expecting prototype for next_sqnum(). Prototype was for ubi_next_sqnum() instead
drivers/mtd/ubi/wl.c:176: warning: expecting prototype for wl_tree_destroy(). Prototype was for wl_entry_destroy() instead
drivers/mtd/ubi/misc.c:24: warning: expecting prototype for calc_data_len(). Prototype was for ubi_calc_data_len() instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Set BLK_MQ_F_BLOCKING so that the block layer always calls ->queue_rq
from process context and drop the driver internal workqueue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Following process will trigger an infinite loop in ubi_wl_put_peb():
ubifs_bgt ubi_bgt
ubifs_leb_unmap
ubi_leb_unmap
ubi_eba_unmap_leb
ubi_wl_put_peb wear_leveling_worker
e1 = rb_entry(rb_first(&ubi->used)
e2 = get_peb_for_wl(ubi)
ubi_io_read_vid_hdr // return err (flash fault)
out_error:
ubi->move_from = ubi->move_to = NULL
wl_entry_destroy(ubi, e1)
ubi->lookuptbl[e->pnum] = NULL
retry:
e = ubi->lookuptbl[pnum]; // return NULL
if (e == ubi->move_from) { // NULL == NULL gets true
goto retry; // infinite loop !!!
$ top
PID USER PR NI VIRT RES SHR S %CPU %MEM COMMAND
7676 root 20 0 0 0 0 R 100.0 0.0 ubifs_bgt0_0
Fix it by:
1) Letting ubi_wl_put_peb() returns directly if wearl leveling entry has
been removed from 'ubi->lookuptbl'.
2) Using 'ubi->wl_lock' protecting wl entry deletion to preventing an
use-after-free problem for wl entry in ubi_wl_put_peb().
Fetch a reproducer in [Link].
Fixes: 43f9b25a9c ("UBI: bugfix: protect from volume removal")
Fixes: ee59ba8b06 ("UBI: Fix stale pointers in ubi->lookuptbl")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216111
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Wear-leveling entry could be freed in error path, which may be accessed
again in eraseblk_count_seq_show(), for example:
__erase_worker eraseblk_count_seq_show
wl = ubi->lookuptbl[*block_number]
if (wl)
wl_entry_destroy
ubi->lookuptbl[e->pnum] = NULL
kmem_cache_free(ubi_wl_entry_slab, e)
erase_count = wl->ec // UAF!
Wear-leveling entry updating/accessing in ubi->lookuptbl should be
protected by ubi->wl_lock, fix it by adding ubi->wl_lock to serialize
wl entry accessing between wl_entry_destroy() and
eraseblk_count_seq_show().
Fetch a reproducer in [Link].
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216305
Fixes: 7bccd12d27 ("ubi: Add debugfs file for tracking PEB state")
Fixes: 801c135ce7 ("UBI: Unsorted Block Images")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
After disabling fastmap(ubi->fm_disabled = 1), fastmap won't be updated,
fm_anchor PEB is missed being scheduled for erasing. Besides, fm_anchor
PEB may have smallest erase count, it doesn't participate wear-leveling.
The difference of erase count between fm_anchor PEB and other PEBs will
be larger and larger later on.
In which situation fastmap can be disabled? Initially, we have an UBI
image with fastmap. Then the image will be atttached without module
parameter 'fm_autoconvert', ubi turns to full scanning mode in one
random attaching process(eg. bad fastmap caused by powercut), ubi
fastmap is disabled since then.
Fix it by not getting fm_anchor if fastmap is disabled in
ubi_refill_pools().
Fetch a reproducer in [Link].
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216341
Fixes: 4b68bf9a69 ("ubi: Select fastmap anchor PEBs considering ...")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Some interface files in debugfs support the read method
dfs_file_read(), but their rwx permissions is shown as
unreadable.
In the user mode, the following problem can be clearly seen:
# ls -l /sys/kernel/debug/ubi/ubi0/
total 0
--w------- 1 root root 0 Oct 22 16:26 chk_fastmap
--w------- 1 root root 0 Oct 22 16:26 chk_gen
--w------- 1 root root 0 Oct 22 16:26 chk_io
-r-------- 1 root root 0 Oct 22 16:26 detailed_erase_block_info
--w------- 1 root root 0 Oct 22 16:26 tst_disable_bgt
--w------- 1 root root 0 Oct 22 16:26 tst_emulate_bitflips
--w------- 1 root root 0 Oct 22 16:26 tst_emulate_io_failures
--w------- 1 root root 0 Oct 22 16:26 tst_emulate_power_cut
--w------- 1 root root 0 Oct 22 16:26 tst_emulate_power_cut_max
--w------- 1 root root 0 Oct 22 16:26 tst_emulate_power_cut_min
It shows that these files do not have read permission 'r',
but we can actually read their contents.
# echo 1 > /sys/kernel/debug/ubi/ubi0/chk_io
# cat /sys/kernel/debug/ubi/ubi0/chk_io
1
User's permission access is determined by capabilities.
Of course, the root user is not restricted from reading
these files.
When reading a debugfs file, the process is as follows:
ksys_read()
vfs_read()
if (file->f_op->read)
file->f_op->read()
full_proxy_open()
real_fops->read()
dfs_file_read() -- Read method of debugfs file.
else if (file->f_op->read_iter)
new_sync_read()
else
ret = -EINVAL -- Return -EINVAL if no read method.
This indicates that the debugfs file can be read as long as the read
method of the debugfs file is registered. This patch adds the read
permission display for file that support the read method.
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
It willl cause null-ptr-deref in the following case:
uif_init()
ubi_add_volume()
cdev_add() -> if it fails, call kill_volumes()
device_register()
kill_volumes() -> if ubi_add_volume() fails call this function
ubi_free_volume()
cdev_del()
device_unregister() -> trying to delete a not added device,
it causes null-ptr-deref
So in ubi_free_volume(), it delete devices whether they are added
or not, it will causes null-ptr-deref.
Handle the error case whlie calling ubi_add_volume() to fix this
problem. If add volume fails, set the corresponding vol to null,
so it can not be accessed in kill_volumes() and release the
resource in ubi_add_volume() error path.
Fixes: 801c135ce7 ("UBI: Unsorted Block Images")
Suggested-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The UBI driver can use the IOCTL to disable the fastmap after the
mainline 669d204469 ("ubi: fastmap: Add fastmap control support
for 'UBI_IOCATT' ioctl"). To destroy the fastmap on a old image,
we need to reattach the device in user space.
However, if the UBI driver build in kernel and the UBI volume is
the root partition, the UBI device cannot be reattached in user
space. To disable fastmap in this case, the UBI must provide the
kernel cmdline parameters to disable fastmap during attach.
This patch add 'enable_fm' as 5th module init parameter of mtd=xx to
control fastmap enable or not. When the value is 0, fastmap will not
create and existed fastmap will destroyed for the given ubi device.
Default value is 0.
To enable or disable fastmap during module loading, fm_autoconvert
must be set to non-zero.
+-----------------+---------------+---------------------------+
| \ | enable_fm=0 | enable_fm=1 |
+-----------------+---------------+---------------------------+
|fm_autoconvert=Y | disable fm | enable fm |
+---------------------------------+---------------------------+
|fm_autoconvert=N | disable fm | Enable fastmap if fastmap |
| | | exists on the old image |
+-------------------------------------------------------------+
Example:
# - Attach mtd1 to ubi1, disable fastmap, mtd2 to ubi2, enable
fastmap.
# modprobe ubi mtd=1,0,0,1,0 mtd=2,0,0,2,1 fm_autoconvert=1
# - If 5th parameter is not specified, the value is 0, fastmap is
disable
# modprobe ubi mtd=1 fm_autoconvert=1
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216623
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
There is a memory leaks problem reported by kmemleak:
unreferenced object 0xffff888102007a00 (size 128):
comm "ubirsvol", pid 32090, jiffies 4298464136 (age 2361.231s)
hex dump (first 32 bytes):
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
backtrace:
[<ffffffff8176cecd>] __kmalloc+0x4d/0x150
[<ffffffffa02a9a36>] ubi_eba_create_table+0x76/0x170 [ubi]
[<ffffffffa029764e>] ubi_resize_volume+0x1be/0xbc0 [ubi]
[<ffffffffa02a3321>] ubi_cdev_ioctl+0x701/0x1850 [ubi]
[<ffffffff81975d2d>] __x64_sys_ioctl+0x11d/0x170
[<ffffffff83c142a5>] do_syscall_64+0x35/0x80
[<ffffffff83e0006a>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
This is due to a mismatch between create and destroy interfaces, and
in detail that "new_eba_tbl" created by ubi_eba_create_table() but
destroyed by kfree(), while will causing "new_eba_tbl->entries" not
freed.
Fix it by replacing kfree(new_eba_tbl) with
ubi_eba_destroy_table(new_eba_tbl)
Fixes: 799dca34ac ("UBI: hide EBA internals")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
There is an use-after-free problem reported by KASAN:
==================================================================
BUG: KASAN: use-after-free in ubi_eba_copy_table+0x11f/0x1c0 [ubi]
Read of size 8 at addr ffff888101eec008 by task ubirsvol/4735
CPU: 2 PID: 4735 Comm: ubirsvol
Not tainted 6.1.0-rc1-00003-g84fa3304a7fc-dirty #14
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS 1.14.0-1.fc33 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
print_report+0x171/0x472
kasan_report+0xad/0x130
ubi_eba_copy_table+0x11f/0x1c0 [ubi]
ubi_resize_volume+0x4f9/0xbc0 [ubi]
ubi_cdev_ioctl+0x701/0x1850 [ubi]
__x64_sys_ioctl+0x11d/0x170
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
</TASK>
When ubi_change_vtbl_record() returns an error in ubi_resize_volume(),
"new_eba_tbl" will be freed on error handing path, but it is holded
by "vol->eba_tbl" in ubi_eba_replace_table(). It means that the liftcycle
of "vol->eba_tbl" and "vol" are different, so when resizing volume in
next time, it causing an use-after-free fault.
Fix it by not freeing "new_eba_tbl" after it replaced in
ubi_eba_replace_table(), while will be freed in next volume resizing.
Fixes: 801c135ce7 ("UBI: Unsorted Block Images")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
If volume size is not multiple of the sector size 512 a warning is
printed saying that the last non-sector aligned bytes will be ignored.
This should be valid for resizable volumes, but when creating static
volumes which are read only this will always be printed even if the
unaligned data is deliberate.
The message is still valid but the severity should be lowered for static
volumes.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
It is possible that current chip->ecc.engine_type value does not match to
configured HW value (if HW ECC checking and generating is enabled or not).
This can happen with old U-Boot bootloader version which either does not
initialize NAND (and let it in some default unusable state) or initialize
NAND with different parameters than what is specified in kernel DTS file.
So if kernel chose to use some chip->ecc.engine_type settings (e.g. from
DTS file) then do not depend on bootloader HW configuration and configures
HW ECC settings according to chip->ecc.engine_type value.
BR_DECC must be set to BR_DECC_CHK_GEN when HW is doing ECC (both
generating and checking), or to BR_DECC_OFF when HW is not doing ECC.
This change fixes usage of SW ECC support in case bootloader explicitly
enabled HW ECC support and kernel DTS file has specified to use SW ECC.
(Of course this works only in case when NAND is not a boot device and both
bootloader and kernel are loaded from different location, e.g. FLASH NOR.)
Fixes: f6424c22aa ("mtd: rawnand: fsl_elbc: Make SW ECC work")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230128134111.32559-1-pali@kernel.org
The INFO() macro defines an ID array and a couple of geometry
properties. Right now all its lines are duplicated twice because of the
INFO6() macro (for extended IDs) and soon as well we will need to add a
geometry parameter to include the number of banks.
In order to limit the code duplication, let's create a number of
intermediate macros which will facilitate defining high-level INFOX()
macros.
There is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20221215081241.407098-2-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Cypress defines two flavors of configuration registers, volatile and
non volatile, and both use the same bit fields. Rename the bitfields in
the configuration registers so that they can be used for both flavors.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <ptyadav@amazon.de>
Link: https://lore.kernel.org/linux-mtd/20230110164703.83413-2-tudor.ambarus@linaro.org
CFR5[6] is reserved bit and must be always 1. Set it to comply with flash
requirements. While fixing SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_{EN, DS}
definition, stop using magic numbers and describe the missing bit fields
in CFR5 register. This is useful for both readability and future possible
addition of Octal STR mode support.
Fixes: c3266af101 ("mtd: spi-nor: spansion: add support for Cypress Semper flash")
Cc: stable@vger.kernel.org
Reported-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Pratyush Yadav <ptyadav@amazon.de>
Tested-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/linux-mtd/20230110164703.83413-1-tudor.ambarus@linaro.org
spi-nor/core.c needs to include linux/delay.h,
or it would raise below compile warning:
drivers/mtd/spi-nor/core.c: In function ‘spi_nor_soft_reset’:
drivers/mtd/spi-nor/core.c:2779:2: error: implicit declaration of function ‘usleep_range’ [-Werror=implicit-function-declaration]
2779 | usleep_range(SPI_NOR_SRST_SLEEP_MIN, SPI_NOR_SRST_SLEEP_MAX);
| ^~~~~~~~~~~~
Fixes: d73ee7534c ("mtd: spi-nor: core: perform a Soft Reset on shutdown")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20220923031457.56103-1-zengheng4@huawei.com
Now the rpcif_{en,dis}able_rpm() wrappers just take a pointer to a
device structure, there is no point in keeping them. Remove them, and
update the callers to call Runtime PM directly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/d87aa5d7e4a39b18f7e2e0649fee0a45b45d371f.1669213027.git.geert+renesas@glider.be
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Most rpcif_*() API functions do not need access to any other fields in
the rpcif structure than the device pointer. Simplify dependencies by
passing the device pointer instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/0460fe82ba348cedec7a9a75a8eff762c50e817b.1669213027.git.geert+renesas@glider.be
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The mx35lf1ge4ab_get_eccsr() function uses an SPI DMA operation to
read the eccsr, hence the buffer should not be on stack. Since commit
380583227c ("spi: spi-mem: Add extra sanity checks on the op param")
the kernel emmits a warning and blocks such operations.
Use the scratch buffer to get eccsr instead of trying to directly read
into a stack-allocated variable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/Y8i85zM0u4XdM46z@makrotopia.org
A number of device drivers reference CONFIG_ARM_S3C24XX_CPUFREQ or
similar symbols that are no longer available with the platform gone,
though the drivers themselves are still used on newer platforms,
so remove these hacks.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These comments are not quite in kernel-doc format and they don't need
to be, so just use "/*" comment markers for them. This prevents these
kernel-doc warnings:
drivers/mtd/nand/raw/vf610_nfc.c:210: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Read accessor for internal SRAM buffer
drivers/mtd/nand/raw/vf610_nfc.c:245: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Write accessor for internal SRAM buffer
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230113064004.24391-1-rdunlap@infradead.org
Add support for sequential cache reads for controllers using the generic
core helpers for their fast read/write helpers.
Sequential reads may reduce the overhead when accessing physically
continuous data by loading in cache the next page while the previous
page gets sent out on the NAND bus.
The ONFI specification provides the following additional commands to
handle sequential cached reads:
* 0x31 - READ CACHE SEQUENTIAL:
Requires the NAND chip to load the next page into cache while keeping
the current cache available for host reads.
* 0x3F - READ CACHE END:
Tells the NAND chip this is the end of the sequential cache read, the
current cache shall remain accessible for the host but no more
internal cache loading operation is required.
On the bus, a multi page read operation is currently handled like this:
00 -- ADDR1 -- 30 -- WAIT_RDY (tR+tRR) -- DATA1_IN
00 -- ADDR2 -- 30 -- WAIT_RDY (tR+tRR) -- DATA2_IN
00 -- ADDR3 -- 30 -- WAIT_RDY (tR+tRR) -- DATA3_IN
Sequential cached reads may instead be achieved with:
00 -- ADDR1 -- 30 -- WAIT_RDY (tR) -- \
31 -- WAIT_RDY (tRCBSY+tRR) -- DATA1_IN \
31 -- WAIT_RDY (tRCBSY+tRR) -- DATA2_IN \
3F -- WAIT_RDY (tRCBSY+tRR) -- DATA3_IN
Below are the read speed test results with regular reads and
sequential cached reads, on NXP i.MX6 VAR-SOM-SOLO in mapping mode with
a NAND chip characterized with the following timings:
* tR: 20 µs
* tRCBSY: 5 µs
* tRR: 20 ns
and the following geometry:
* device size: 2 MiB
* eraseblock size: 128 kiB
* page size: 2 kiB
============= Normal read @ 33MHz =================
mtd_speedtest: eraseblock read speed is 15633 KiB/s
mtd_speedtest: page read speed is 15515 KiB/s
mtd_speedtest: 2 page read speed is 15398 KiB/s
===================================================
========= Sequential cache read @ 33MHz ===========
mtd_speedtest: eraseblock read speed is 18285 KiB/s
mtd_speedtest: page read speed is 15875 KiB/s
mtd_speedtest: 2 page read speed is 16253 KiB/s
===================================================
We observe an overall speed improvement of about 5% when reading
2 pages, up to 15% when reading an entire block. This is due to the
~14us gain on each additional page read (tR - (tRCBSY + tRR)).
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
Tested-by: Liao Jaime <jaimeliao.tw@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20230112093637.987838-4-miquel.raynal@bootlin.com
Add an empty envelope just to show how to add additional checks for new
operations. This is going to be used for sequential cached reads, which
require the page size to be known (and the discovery to be over), hence
the "late" designation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Liao Jaime <jaimeliao.tw@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20230112093637.987838-3-miquel.raynal@bootlin.com
Instead of checking if a pattern is supported each time we need it,
let's create a bitfield that only the core would be allowed to fill at
startup time. The core and the individual drivers may then use it in
order to check what operation they should use. This bitfield is supposed
to grow over time.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Liao Jaime <jaimeliao.tw@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20230112093637.987838-2-miquel.raynal@bootlin.com
With the TMIO MFD drivers gone, the NAND support is also
obsolete and can be removed.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Up to now the pasemi nand driver only supported a single device
instance. However the check for that was racy because two parallel calls
of pasemi_nand_probe() could pass the check
if (pasemi_nand_mtd)
return -ENODEV;
before any of them assigns a non-NULL value to it.
So rework the driver to make use of per-device driver data.
As an intended side effect the driver can bind more than one device and
also gets rid of the check
if (!pasemi_nand_mtd)
return 0;
in the remove callback that could only ever trigger after the above race
happened.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230102124051.1508424-1-u.kleine-koenig@pengutronix.de
Building with -Werror=override-init reveals that two patches added
the same device ID table to this driver:
drivers/mtd/devices/mtd_dataflash.c:946:27: error: initialized field overwritten [-Werror=override-init]
946 | .id_table = dataflash_spi_ids,
| ^~~~~~~~~~~~~~~~~
drivers/mtd/devices/mtd_dataflash.c:946:27: note: (near initialization for 'dataflash_driver.id_table')
Remove one of the copies.
Fixes: 27a030e872 ("mtd: dataflash: Add device-tree SPI IDs")
Fixes: ac4f83482a ("mtd: dataflash: Add SPI ID table")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221215164736.1315815-1-arnd@kernel.org
Each chip is required to have a unique CS number ("reg" property) in the
range 0-7, so there is no need to separately count the number of chips.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221229181526.53766-4-samuel@sholland.org
If a chip fails to initialize, we need to clean up any chips that were
already initialized/registered.
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221229181526.53766-2-samuel@sholland.org
A missing layouts were added to the driver to support NAND flashes
with ECC layouts of 12 or 16 with page sized of 2048, 4096 or 8192.
Usually theses are rare layouts, but in Marvell AC5 driver, the ECC
level is set according to the spare area, so we may use these layouts
more frequently.
Signed-off-by: Aviram Dali <aviramd@marvell.com>
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221216162715.3230766-1-vadym.kochan@plvision.eu
When MTD or MTD_CFI_GEOMETRY is disabled, the spi-intel driver
fails to build, as it includes the shared CFI header:
include/linux/mtd/cfi.h:62:2: error: #warning No CONFIG_MTD_CFI_Ix selected. No NOR chip support can work. [-Werror=cpp]
62 | #warning No CONFIG_MTD_CFI_Ix selected. No NOR chip support can work.
linux/mtd/spi-nor.h does not actually need to include cfi.h, so
remove the inclusion here to fix the warning. This uncovers a
missing #include in spi-nor/core.c so add that there to
prevent a different build issue.
Fixes: e23e5a05d1 ("mtd: spi-nor: intel-spi: Convert to SPI MEM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Tokunori Ikegami <ikegami.t@gmail.com>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221220141352.1486360-1-arnd@kernel.org
This fixes the following compile error on mips architecture with clang
version 16.0.0 reported by the 0-DAY CI Kernel Test Service:
ld.lld: error: undefined symbol: __udivdi3
referenced by scpart.c
mtd/parsers/scpart.o:(scpart_parse) in archive drivers/built-in.a
As a workaround this makes 'offs' a 32-bit type. This is enough, because
the mtd containing partition table practically does not exceed 1 MB. We
can revert this when the [Link] has been resolved.
Link: https://github.com/ClangBuiltLinux/linux/issues/1635
Fixes: 9b78ef0c79 ("mtd: parsers: add support for Sercomm partitions")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/805fe58e-690f-6a3f-5ebf-2f6f6e6e4599@gmail.com
The parts needs to be freed with all its elements, otherwise it will be
leaked.
Fixes: 00a3588084 ("mtd: parsers: add TP-Link SafeLoader partitions table parser")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221208113620.78855-1-yuancan@huawei.com
BFPT_DWORD() converts 1-based indexing to 0-based indexing for C arrays,
and is used in BFPT parse. Per JESD216F.02, the conversion is applicable
to other parameter tables than BFPT. This patch renames the macro to
SFDP_DWORD() so that we can use it for other parameter tables than BFPT.
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/e42feac840fe3a31187419e91b2d514d9f259d15.1672026365.git.Takahiro.Kuwano@infineon.com
* Fix refcount error in del_mtd_device()
* Fix possible resource leak in init_mtd()
* Set ROOT_DEV for partitions marked as rootfs in DT
* Describe marking rootfs partitions in the bindings
* Fix device name leak when register device failed in add_mtd_device()
* Try to find OF node for every MTD partition
* simplify (a bit) code find partition-matching dynamic OF node
MTD driver changes:
* pxa2xx-flash maps: fix memory leak in probe
* BCM parser: refer to ARCH_BCMBCA instead of ARCH_BCM4908
* lpddr2_nvm: Fix possible null-ptr-deref
* inftlcore: fix repeated words in comments
* lart: remove driver
* tplink:
- Add TP-Link SafeLoader partitions table parser and bindings
- Describe TP-Link SafeLoader parser
- Describe TP-Link SafeLoader dynamic subpartitions
* mtdoops:
- Panic caused mtdoops to call mtdoops_erase function immediately
- Add mtdoops_erase function and move mtdoops_inc_counter to after it
- Change printk() to counterpart pr_ functions
MTD binding cleanup:
* Fixed-partitions: Fix 'sercomm,scpart-id' schema
* Standardize the style in the examples
* Drop object types when referencing other files
* Argue in favor of keeping additionalProperties set to true
* NVMEM-cells:
- Inherit from MTD partitions
- Drop range property from example
* Partitions:
- Change qcom,smem-part partition type
- Constrain the list of parsers
* Physmap: Reuse the generic definitions
* SPI-NOR: Drop common properties
* Sunxi-nand: Add an example to validate the bindings
* Onenand: Mention the expected node name
* Ingenic: Mark partitions in the controller node as deprecated
* NAND:
- Standardize the child node name
- Drop common properties already defined in generic files
- nand-chip.yaml should reference mtd.yaml
* Remove useless file about partitions
* Clarify all partition subnodes
SPI NOR core changes:
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Raw NAND core changes:
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmOOBbQACgkQJWrqGEe9
VoRB7wf9EY8IeRhumaeN9WT+VrmPxGOu61m/eilUK4xvgj6JX/yhYo/kKW9eEp+o
5I8JLimG6uo7rZNlbixGMbHd41aTu9MplLrTA42nzGadl3w4D8p9c1ic6sEiv7SI
qgnAbzq3FLUPDLLDV0IfrMQvsQgJkv3b+r8ShPt9uJy3cmnKQzOvIhs43wwLnOXp
NPiMbVjpS4FAmNvG7nI0xfcBLO/eFaTuQc+UyfP2SwkVIAN5xfUAwOPOHZWBstmR
zhJlHSFJWrg+J9T9bsRW7D5q/MVxqNsMH589c9aXHNqzgzZs2FTopDUf6cWwHr0f
2Ssot2naIdvU+eLGA12hDuUDDoRwKA==
=Igti
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Fix refcount error in del_mtd_device()
- Fix possible resource leak in init_mtd()
- Set ROOT_DEV for partitions marked as rootfs in DT
- Describe marking rootfs partitions in the bindings
- Fix device name leak when register device fails in add_mtd_device()
- Try to find OF node for every MTD partition
- simplify (a bit) code find partition-matching dynamic OF node
MTD driver changes:
- pxa2xx-flash maps: fix memory leak in probe
- BCM parser: refer to ARCH_BCMBCA instead of ARCH_BCM4908
- lpddr2_nvm: Fix possible null-ptr-deref
- inftlcore: fix repeated words in comments
- lart: remove driver
- tplink:
- Add TP-Link SafeLoader partitions table parser and bindings
- Describe TP-Link SafeLoader parser
- Describe TP-Link SafeLoader dynamic subpartitions
- mtdoops:
- Panic caused mtdoops to call mtdoops_erase function immediately
- Add mtdoops_erase function and move mtdoops_inc_counter after it
- Change printk() to counterpart pr_ functions
MTD binding cleanup:
- Fixed-partitions: Fix 'sercomm,scpart-id' schema
- Standardize the style in the examples
- Drop object types when referencing other files
- Argue in favor of keeping additionalProperties set to true
- NVMEM-cells:
- Inherit from MTD partitions
- Drop range property from example
- Partitions:
- Change qcom,smem-part partition type
- Constrain the list of parsers
- Physmap: Reuse the generic definitions
- SPI-NOR: Drop common properties
- Sunxi-nand: Add an example to validate the bindings
- Onenand: Mention the expected node name
- Ingenic: Mark partitions in the controller node as deprecated
- NAND:
- Standardize the child node name
- Drop common properties already defined in generic files
- nand-chip.yaml should reference mtd.yaml
- Remove useless file about partitions
- Clarify all partition subnodes
SPI NOR core changes:
- Add support for flash reset using the dt reset-gpios property.
- Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
- Bypass zero erase size in spi_nor_find_best_erase_type().
- Fix select_uniform_erase to skip 0 erase size
- Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described
solely by the flash's SFDP tables.
- Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
- Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP
discoverable.
SPI NOR manufacturer drivers changes:
- Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
- Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
- Micron - ST: Enable locking for mt25qu256a.
- Winbond: Add support for W25Q512NW-IQ.
- ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Raw NAND core changes:
- Drop obsolete dependencies on COMPILE_TEST
- MAINTAINERS: rectify entry for MESON NAND controller bindings
- Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
- marvell: Enable NFC/DEVBUS arbiter
- gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
- mpc5121: Replace NO_IRQ by 0
- lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
- lpc32xx_mlc: Switch to using pm_ptr()
- cadence: Support 64-bit slave dma interface
- rockchip: Describe rk3128-nfc in the bindings
- brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
- winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification"
* tag 'mtd/for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (76 commits)
mtd: rawnand: Drop obsolete dependencies on COMPILE_TEST
mtd: maps: pxa2xx-flash: fix memory leak in probe
mtd: core: Fix refcount error in del_mtd_device()
mtd: spi-nor: add SFDP fixups for Quad Page Program
mtd: spi-nor: issi: is25wp256: Init flash based on SFDP
mtd: spi-nor: winbond: add support for W25Q512NW-IQ
mtd: spi-nor: micron-st: Enable locking for mt25qu256a
mtd: spi-nor: Fix the number of bytes for the dummy cycles
mtd: spi-nor: gigadevice: gd25q256: replace gd25q256_default_init with gd25q256_post_bfpt
mtd: spi-nor: Fix formatting in spi_nor_read_raw() kerneldoc comment
mtd: spi-nor: sysfs: print JEDEC ID for generic flash driver
mtd: spi-nor: add generic flash driver
mtd: spi-nor: fix select_uniform_erase to skip 0 erase size
mtd: spi-nor: move function declaration out of sfdp.h
mtd: spi-nor: remember full JEDEC flash ID
mtd: spi-nor: sysfs: hide manufacturer if it is not set
mtd: spi-nor: hide jedec_id sysfs attribute if not present
mtd: spi-nor: Check for zero erase size in spi_nor_find_best_erase_type()
mtd: rawnand: marvell: Enable NFC/DEVBUS arbiter
mtd: parsers: refer to ARCH_BCMBCA instead of ARCH_BCM4908
...
-----BEGIN PGP SIGNATURE-----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=QRhK
-----END PGP SIGNATURE-----
Merge tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator updates from Jason Donenfeld:
- Replace prandom_u32_max() and various open-coded variants of it,
there is now a new family of functions that uses fast rejection
sampling to choose properly uniformly random numbers within an
interval:
get_random_u32_below(ceil) - [0, ceil)
get_random_u32_above(floor) - (floor, U32_MAX]
get_random_u32_inclusive(floor, ceil) - [floor, ceil]
Coccinelle was used to convert all current users of
prandom_u32_max(), as well as many open-coded patterns, resulting in
improvements throughout the tree.
I'll have a "late" 6.1-rc1 pull for you that removes the now unused
prandom_u32_max() function, just in case any other trees add a new
use case of it that needs to converted. According to linux-next,
there may be two trivial cases of prandom_u32_max() reintroductions
that are fixable with a 's/.../.../'. So I'll have for you a final
conversion patch doing that alongside the removal patch during the
second week.
This is a treewide change that touches many files throughout.
- More consistent use of get_random_canary().
- Updates to comments, documentation, tests, headers, and
simplification in configuration.
- The arch_get_random*_early() abstraction was only used by arm64 and
wasn't entirely useful, so this has been replaced by code that works
in all relevant contexts.
- The kernel will use and manage random seeds in non-volatile EFI
variables, refreshing a variable with a fresh seed when the RNG is
initialized. The RNG GUID namespace is then hidden from efivarfs to
prevent accidental leakage.
These changes are split into random.c infrastructure code used in the
EFI subsystem, in this pull request, and related support inside of
EFISTUB, in Ard's EFI tree. These are co-dependent for full
functionality, but the order of merging doesn't matter.
- Part of the infrastructure added for the EFI support is also used for
an improvement to the way vsprintf initializes its siphash key,
replacing an sleep loop wart.
- The hardware RNG framework now always calls its correct random.c
input function, add_hwgenerator_randomness(), rather than sometimes
going through helpers better suited for other cases.
- The add_latent_entropy() function has long been called from the fork
handler, but is a no-op when the latent entropy gcc plugin isn't
used, which is fine for the purposes of latent entropy.
But it was missing out on the cycle counter that was also being mixed
in beside the latent entropy variable. So now, if the latent entropy
gcc plugin isn't enabled, add_latent_entropy() will expand to a call
to add_device_randomness(NULL, 0), which adds a cycle counter,
without the absent latent entropy variable.
- The RNG is now reseeded from a delayed worker, rather than on demand
when used. Always running from a worker allows it to make use of the
CPU RNG on platforms like S390x, whose instructions are too slow to
do so from interrupts. It also has the effect of adding in new inputs
more frequently with more regularity, amounting to a long term
transcript of random values. Plus, it helps a bit with the upcoming
vDSO implementation (which isn't yet ready for 6.2).
- The jitter entropy algorithm now tries to execute on many different
CPUs, round-robining, in hopes of hitting even more memory latencies
and other unpredictable effects. It also will mix in a cycle counter
when the entropy timer fires, in addition to being mixed in from the
main loop, to account more explicitly for fluctuations in that timer
firing. And the state it touches is now kept within the same cache
line, so that it's assured that the different execution contexts will
cause latencies.
* tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (23 commits)
random: include <linux/once.h> in the right header
random: align entropy_timer_state to cache line
random: mix in cycle counter when jitter timer fires
random: spread out jitter callback to different CPUs
random: remove extraneous period and add a missing one in comments
efi: random: refresh non-volatile random seed when RNG is initialized
vsprintf: initialize siphash key using notifier
random: add back async readiness notifier
random: reseed in delayed work rather than on-demand
random: always mix cycle counter in add_latent_entropy()
hw_random: use add_hwgenerator_randomness() for early entropy
random: modernize documentation comment on get_random_bytes()
random: adjust comment to account for removed function
random: remove early archrandom abstraction
random: use random.trust_{bootloader,cpu} command line option only
stackprotector: actually use get_random_canary()
stackprotector: move get_random_canary() into stackprotector.h
treewide: use get_random_u32_inclusive() when possible
treewide: use get_random_u32_{above,below}() instead of manual loop
treewide: use get_random_u32_below() instead of deprecated function
...
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmOJ59AACgkQS1VPR6WN
FOnzOQf/WLBTNFtPcJoS7cdjlh4fuGySDUKuLifOX+Tmk/ki3XFCZR98cESgb5m+
hCyFDeER/qfdOK9ObT3K1GBS6x7zx8YkskbucjAU0vlIsr2ZHCjNpNiAHrADsKjR
579N0Xwh2ibh7uVJ1xvsPwObdAc8P/tjGHHWF6hGEZzIPYXJVce+qDktkkLfbZ/P
Fik6+y3h68wW/0kDNt/gNmNcb5Z3fjxySs21Np5sy7bUtVVBjHWLo0OpjNadDH9M
m6AkhFA5h9OVl5E4jHBpxc4NvlAa5f6520vESpieseNJiIMWo0W/eSkVsframFew
ILdtXCHjkbS6kgvSpUViobMFsgCjaA==
=Yi2q
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.2' into mtd/next
SPI NOR core changes:
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Fix merge conflict in the jedec,spi-nor bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmOGGfIACgkQJWrqGEe9
VoSZVQgAmew5RtMegFus/AXflUsGYCvZKfV1LVnxmSoGIKBrJr3yjzh6mFuLyzaP
qt2KljEJ4dblk2M3efosX5YeAkz7A7evm218NHGeKWHMPCDimSE1ptAyBhhMmsVi
cgCgu3LXh369dK9OAm7ZVR4hOdDuK5rpYIcXA4mUh0yqiFxfxsuuNY7QBDVrN+qt
SNmZkTBbCgGRxo7RRanN2ljnSm31p6TyhngUDKG89puMka9gGA9yWLbWFDpwM5SS
L0Tr2ZOHctzz/X/1s2yPcnN6ZPpqsc1wLnGyLOWlhkm7oo7aiT59rlHj9GHbp82h
7lXf7MeWxSNSVr9PMHHUR7XDqlLaOw==
=aOZ+
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.2' into mtd/next
Raw NAND core changes:
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
Fix merge conflict with mtd tree regarding the brcm bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221124115946.5edb771c@endymion.delvare
SFDP table of some flash chips do not advertise support of Quad Input
Page Program even though it has support. Use flags and add hardware
cap for these chips.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@sifive.com>
[tudor.ambarus@microchip.com: move pp setting in spi_nor_init_default_params]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220920184808.44876-2-sudip.mukherjee@sifive.com
The datasheet of is25wp256 says it supports SFDP. Get rid of the static
initialization of the flash parameters and init them when parsing SFDP.
Testing showed the flash using SPINOR_OP_READ_1_1_4_4B 0x6c,
SPINOR_OP_PP_4B 0x12 and SPINOR_OP_BE_4K_4B 0x21 before enabling SFDP.
After this patch, it parses the SFDP information and still uses the
same opcodes.
Set sector_size and n_sectors to zero as they will be discovered when
parsing SFDP.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@sifive.com>
[tudor.ambarus@microchip.com: set sector_size and n_sectors to zero]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220920184808.44876-1-sudip.mukherjee@sifive.com
The number of bytes used by spi_nor_spimem_check_readop() may be
incorrect for the dummy cycles. Since nor->read_dummy is not initialized
before spi_nor_spimem_adjust_hwcaps().
We use both mode and wait state clock cycles instead of nor->read_dummy.
Fixes: 0e30f47232 ("mtd: spi-nor: add support for DTR protocol")
Co-developed-by: Bayi Cheng <bayi.cheng@mediatek.com>
Signed-off-by: Bayi Cheng <bayi.cheng@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20221031124633.13189-1-allen-kh.cheng@mediatek.com
When utilizing PARSE_SFDP to initialize the flash parameter, the
deprecated initializing method spi_nor_init_params_deprecated() and the
function spi_nor_manufacturer_init_params() within it will never be
executed, which results in the default_init hook function will also never
be executed.
This is okay for 'D' generation of GD25Q256, because 'D' generation is
implementing the JESD216B standards, it has QER field defined in BFPT,
parsing the SFDP can properly set the quad_enable function. The 'E'
generation also implements the JESD216B standards, and it has the same
status register definitions as 'D' generation, parsing the SFDP to set
the quad_enable function should also work for 'E' generation.
However, the same thing can't apply to 'C' generation. 'C' generation
'GD25Q256C' implements the JESD216 standards, and it doesn't have the
QER field defined in BFPT, since it does have QE bit in status register
1, the quad_enable hook needs to be tweaked to properly set the
quad_enable function, this can be done in post_bfpt fixup hook.
Fixes: 047275f7de ("mtd: spi-nor: gigadevice: gd25q256: Init flash based on SFDP")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Yaliang Wang <Yaliang.Wang@windriver.com>
[tudor.ambarus@microchip.com: Update comment in gd25q256_post_bfpt]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221016171901.1483542-2-yaliang.wang@windriver.com
It doesn't make sense to put "set" on its own line like that.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20221101162906.990125-1-j.neuschaefer@gmx.net
We don't have a database entry for the generic SPI-NOR flash driver and
thus we don't have a JEDEC ID to print. Print the (cached) JEDEC ID
instead.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-8-michael@walle.cc
Our SFDP parsing is everything we need to support all basic operations
of a flash device. If the flash isn't found in our in-kernel flash
database, gracefully fall back to a driver described solely by its SFDP
tables.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-7-michael@walle.cc
4bait will set the erase size to 0 if there is no corresponding
opcode for the 4byte erase. Fix spi_nor_select_uniform_erase to skip
the 0 erase size to avoid mtd device registration failure cases.
Reported-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-6-michael@walle.cc
sfdp.h should only contain constants related to the JEDEC SFDP
specification(s).
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-5-michael@walle.cc
At the moment, we print the JEDEC ID that is stored in our database. The
generic flash support won't have such an entry in our database. To find
out the JEDEC ID later we will have to cache it. There is also another
advantage: If the flash is found in the database, the ID could be
truncated because the ID of the entry is used which can be shorter. Some
flashes still holds valuable information in the bytes after the JEDEC ID
and come in handy during debugging of when coping with INFO6() entries.
These are not accessible for now.
Save a copy of the ID bytes after reading and display it via debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-4-michael@walle.cc
The manufacturer may be optional when pure SFDP flashes are supported.
Hide the sysfs property if no manufacturer is set.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-3-michael@walle.cc
Some non-jedec compliant flashes (like the Everspin flashes) don't have
an ID at all. Hide the attribute in this case.
Fixes: 36ac022862 ("mtd: spi-nor: add initial sysfs support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-2-michael@walle.cc
Erase can be zeroed in spi_nor_parse_4bait() or
spi_nor_init_non_uniform_erase_map(). In practice it happened with
mt25qu256a, which supports 4K, 32K, 64K erases with 3b address commands,
but only 4K and 64K erase with 4b address commands.
Fixes: dc92843159 ("mtd: spi-nor: fix erase_type array to indicate current map conf")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211119081412.29732-1-alexander.sverdlin@nokia.com
These cases were done with this Coccinelle:
@@
expression H;
expression L;
@@
- (get_random_u32_below(H) + L)
+ get_random_u32_inclusive(L, H + L - 1)
@@
expression H;
expression L;
expression E;
@@
get_random_u32_inclusive(L,
H
- + E
- - E
)
@@
expression H;
expression L;
expression E;
@@
get_random_u32_inclusive(L,
H
- - E
- + E
)
@@
expression H;
expression L;
expression E;
expression F;
@@
get_random_u32_inclusive(L,
H
- - E
+ F
- + E
)
@@
expression H;
expression L;
expression E;
expression F;
@@
get_random_u32_inclusive(L,
H
- + E
+ F
- - E
)
And then subsequently cleaned up by hand, with several automatic cases
rejected if it didn't make sense contextually.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This is a simple mechanical transformation done by:
@@
expression E;
@@
- prandom_u32_max
+ get_random_u32_below
(E)
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Reviewed-by: SeongJae Park <sj@kernel.org> # for damon
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> # for arm
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The CN9130 SoC (an ARMADA 8K type) has both a NAND Flash Controller and
a generic local bus controller (Device Bus Controller) that share common
pins.
With a board design that incorporates both a NAND flash and uses
the Device Bus (in our case for an SRAM) accessing the Device Bus device
fails unless the NfArbiterEn bit is set. Setting the bit enables
arbitration between the Device Bus and the NAND flash.
Since there is no obvious downside in enabling this for designs that
don't require arbitration, we always enable it.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221109231325.7714-1-hamish.martin@alliedtelesis.co.nz
Commit dd5c672d7c ("arm64: bcmbca: Merge ARCH_BCM4908 to ARCH_BCMBCA")
removes config ARCH_BCM4908 as config ARCH_BCMBCA has the same intent.
Probably due to concurrent development, commit 002181f5b1 ("mtd: parsers:
add Broadcom's U-Boot parser") introduces 'Broadcom's U-Boot partition
parser' that depends on ARCH_BCM4908, but this use was not visible during
the config refactoring from the commit above. Hence, these two changes
create a reference to a non-existing config symbol.
Adjust the MTD_BRCM_U_BOOT definition to refer to ARCH_BCMBCA instead of
ARCH_BCM4908 to remove the reference to the non-existing config symbol
ARCH_BCM4908.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221116124932.4748-1-lukas.bulwahn@gmail.com
There is already a real partitions.yaml file, so assuming everybody
knows hot to read yaml schema now, this text file is no longer needed,
so drop it.
Depending on the situation, the lines referring to this file are either
dropped or edited to point to mtd.yaml which includes partition{,s}.yaml.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20221114090315.848208-3-miquel.raynal@bootlin.com
The switch to using the gpiod API removed the last user of
lpc32xx_wp_disable() outside #ifdef CONFIG_PM, causing build failures if
CONFIG_PM=n:
drivers/mtd/nand/raw/lpc32xx_slc.c:318:13: error: ‘lpc32xx_wp_disable’ defined but not used [-Werror=unused-function]
318 | static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host)
| ^~~~~~~~~~~~~~~~~~
Fix this by switching from #ifdef CONFIG_PM to pm_ptr(), increasing
compile-coverage as a side-effect.
Reported-by: noreply@ellerman.id.au
Fixes: 6b923db286 ("mtd: rawnand: lpc32xx_slc: switch to using gpiod API")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221027131028.3838303-2-geert@linux-m68k.org
The switch to using the gpiod API removed the last user of
lpc32xx_wp_disable() outside #ifdef CONFIG_PM, causing build failures if
CONFIG_PM=n:
drivers/mtd/nand/raw/lpc32xx_mlc.c:380:13: error: ‘lpc32xx_wp_disable’ defined but not used [-Werror=unused-function]
380 | static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host)
| ^~~~~~~~~~~~~~~~~~
Fix this by switching from #ifdef CONFIG_PM to pm_ptr(), increasing
compile-coverage as a side-effect.
Reported-by: noreply@ellerman.id.au
Fixes: 782e32a990 ("mtd: rawnand: lpc32xx_mlc: switch to using gpiod API")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221027131028.3838303-1-geert@linux-m68k.org
I got the error report while inject fault in init_mtd():
sysfs: cannot create duplicate filename '/devices/virtual/bdi/mtd-0'
Call Trace:
<TASK>
dump_stack_lvl+0x67/0x83
sysfs_warn_dup+0x60/0x70
sysfs_create_dir_ns+0x109/0x120
kobject_add_internal+0xce/0x2f0
kobject_add+0x98/0x110
device_add+0x179/0xc00
device_create_groups_vargs+0xf4/0x100
device_create+0x7b/0xb0
bdi_register_va.part.13+0x58/0x2d0
bdi_register+0x9b/0xb0
init_mtd+0x62/0x171 [mtd]
do_one_initcall+0x6c/0x3c0
do_init_module+0x58/0x222
load_module+0x268e/0x27d0
__do_sys_finit_module+0xd5/0x140
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
kobject_add_internal failed for mtd-0 with -EEXIST, don't try to register
things with the same name in the same directory.
Error registering mtd class or bdi: -17
If init_mtdchar() fails in init_mtd(), mtd_bdi will not be unregistered,
as a result, we can't load the mtd module again, to fix this by calling
bdi_unregister(mtd_bdi) after out_procfs label.
Fixes: 445caaa20c ("mtd: Allocate bdi objects dynamically")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221024065109.2050705-1-cuigaosheng1@huawei.com
This adds support for "linux,rootfs" binding that is used to mark flash
partition containing rootfs. It's useful for devices using device tree
that don't have bootloader passing root info in cmdline.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221022211318.32009-2-zajec5@gmail.com
On 64 bit systems, the highest 32 bits of the "offset" variable are
not initialized. Also the existing code is not endian safe (it will
fail on big endian systems). Change the type of "offset" to a u32.
Fixes: aec4d5f5ffd0 ("mtd: parsers: add TP-Link SafeLoader partitions table parser")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/Y1gCALFWXYYwqV1P@kili
The panic function disables the local interrupts, preemption, and all
other processors. When the invoked mtdoops needs to erase a used page,
calling schedule_work() to do it will not work. Instead, just call
mtdoops_erase function immediately.
Tested:
~# echo c > /proc/sysrq-trigger
[ 171.654759] sysrq: Trigger a crash
[ 171.658325] Kernel panic - not syncing: sysrq triggered crash
......
[ 172.406423] mtdoops: not ready 34, 35 (erase immediately)
[ 172.432285] mtdoops: ready 34, 35
[ 172.435633] Rebooting in 10 seconds..
Signed-off-by: Ray Zhang <sgzhang@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221010045549.2221965-4-sgzhang@google.com
Preparing for next patch with minimal code difference, add mtdoops_erase
function and move mtdoops_inc_counter to after it, with no functional
change.
Signed-off-by: Ray Zhang <sgzhang@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221010045549.2221965-3-sgzhang@google.com
To comply with latest kernel code requirement, change printk() to
counterpart pr_ functions in mtdoops driver:
- change printk(INFO) to pr_info()
- change printk(DEBUG) to pr_debug()
- change printk(WARNING) to pr_warn()
- change printk(ERR) to pr_err()
Note that only if dynamic debugging is enabled or DEBUG is defined,
printk(KERN_DEBUG) and pr_debug() are equivalent; Otherwise pr_debug()
is no-op, causing different behavior.
Signed-off-by: Ray Zhang <sgzhang@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221010045549.2221965-2-sgzhang@google.com
So far this feature was limited to the top-level "nvmem-cells" node.
There are multiple parsers creating partitions and subpartitions
dynamically. Extend that code to handle them too.
This allows finding partition-* node for every MTD (sub)partition.
Random example:
partitions {
compatible = "brcm,bcm947xx-cfe-partitions";
partition-firmware {
compatible = "brcm,trx";
partition-loader {
};
};
};
Cc: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221004083710.27704-2-zajec5@gmail.com
OMAP2 OneNAND driver uses gpmc_omap_onenand_set_timings() provided by
OMAP_GPMC driver, so the latter cannot be module if OneNAND driver is
built-in:
/usr/bin/arm-linux-gnueabi-ld: drivers/mtd/nand/onenand/onenand_omap2.o: in function `omap2_onenand_probe':
onenand_omap2.c:(.text+0x520): undefined reference to `gpmc_omap_onenand_set_timings'
The OMAP_GPMC is also a runtime dependency.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 854fd9209b ("memory: omap-gpmc: Allow building as a module")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221107091520.127053-1-krzysztof.kozlowski@linaro.org
The compiler is not smart enough to notice that it's impossible for
them to be actually used uninitialized. Which exact variables trip
here varies depending on random surrounding code; none triggered in
6.1-rc1 but 6.1-rc2 fails on three of these five, despite variables
declared in the very same line having identical flow.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221024092026.42123-1-kilobyte@angband.pl
With use_codeword_fixup enabled, any return from
mtd_device_parse_register gets overwritten. Aside from the clear bug, this
is also problematic as a parser can EPROBE_DEFER and because this is not
correctly handled, the nand is never rescanned later in the bootup
process.
An example of this problem is when smem requires additional time to be
probed and nandc use qcomsmempart as parser. Parser will return
EPROBE_DEFER but in the current code this ret gets overwritten by
qcom_nand_host_parse_boot_partitions and qcom_nand_host_init_and_register
return 0.
Correctly handle the return code from mtd_device_parse_register so that
any error from this function is not ignored.
Fixes: 862bdedd7f ("mtd: nand: raw: qcom_nandc: add support for unprotected spare data pages")
Cc: stable@vger.kernel.org # v6.0+
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221021165304.19991-1-ansuelsmth@gmail.com
Add an error message when failing to exit the 4-byte address mode. Do not
stop the execution and go through the spi_nor_soft_reset() method if used,
in the hope that the flash will default to 3-byte address mode after the
reset.
Suggested-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220728030159.68680-1-tudor.ambarus@microchip.com
We track in the core the internal address mode of the flash. Stop using
hardcoded values for the number of bytes of address and use
nor->addr_nbytes and nor->params->addr_mode_nbytes instead.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220728041451.85559-3-tudor.ambarus@microchip.com
We track in the core the internal address mode of the flash. Stop using
hardcoded values for the number of bytes of address and use
nor->addr_nbytes and nor->params->addr_mode_nbytes instead.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220728041451.85559-2-tudor.ambarus@microchip.com
Read, Page Program, and Sector Erase settings are done in SFDP so we can
remove NO_SFDP_FLAGS from s28hs512t info. Since the default_init() is no
longer called after removing NO_SFDP_FLAGS, the initialization in the
default_init() is moved to late_init().
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/12e468992f5d0cbd474abff3203100cc8163d4e5.1661915569.git.Takahiro.Kuwano@infineon.com
Add support for spi-nor flash reset via GPIO controller by reading the
reset-gpio property. If there is a valid GPIO specifier then reset will
be performed by asserting and deasserting the GPIO using gpiod APIs
otherwise it will not perform any operation.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220908064428.2962-3-sai.krishna.potthuri@amd.com
There is some code in the parser that tries to read 0x8000
bytes into a block to "read in the middle" of the block. Well
that only works if the block is also 0x10000 bytes all the time,
else we get these parse errors as we reach the end of the flash:
spi-nor spi0.0: mx25l1606e (2048 Kbytes)
mtd_read error while parsing (offset: 0x200000): -22
mtd_read error while parsing (offset: 0x201000): -22
(...)
Fix the code to do what I think was intended.
Cc: stable@vger.kernel.org
Fixes: f0501e81fb ("mtd: bcm47xxpart: alternative MAGIC for board_data partition")
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221018091129.280026-1-linus.walleij@linaro.org
Winbond uses 3 bytes to identify flash: vendor_id, dev_id_0, dev_id_1,
but current driver uses only first 2 bytes of it for devices
identification. As result Winbond W25N02KV flash (id_bytes: EF, AA, 22)
is identified as W25N01GV (id_bytes: EF, AA, 21).
Fix this by adding missed identification bytes.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221010105110.446674-1-mikhail.kshevetskiy@iopsys.eu
NO_IRQ is used to check the return of irq_of_parse_and_map().
On some architecture NO_IRQ is 0, on other architectures it is -1.
irq_of_parse_and_map() returns 0 on error, independent of NO_IRQ.
So use 0 instead of using NO_IRQ.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/4e3ca3e0077ea124ea210c312e6e620f0f9e8bca.1665034065.git.christophe.leroy@csgroup.eu
Originally the absence of the marvell,nand-keep-config property caused
the setup_data_interface function to be provided. However when
setup_data_interface was moved into nand_controller_ops the logic was
unintentionally inverted. Update the logic so that only if the
marvell,nand-keep-config property is present the bootloader NAND config
kept.
Cc: stable@vger.kernel.org
Fixes: 7a08dbaedd ("mtd: rawnand: Move ->setup_data_interface() to nand_controller_ops")
Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220927024728.28447-1-chris.packham@alliedtelesis.co.nz
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Cc: stable@vger.kernel.org
Fixes: d7d9f8ec77 ("mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220926084456.98160-1-zhangqilong3@huawei.com
The 'chip_np' returned by of_get_next_child() with refcount decremented,
of_node_put() need be called in error path to decrease the refcount.
Fixes: bfc618fcc3 ("mtd: rawnand: intel: Read the chip-select line from the correct OF node")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220924131010.957117-1-yangyingliang@huawei.com
The Intel SPI-NOR controller does not support the 4-byte address opcode
so ->set_4byte_addr_mode() ends up returning -ENOTSUPP and the SPI flash
chip probe fail like this:
[ 12.291082] spi-nor: probe of spi0.0 failed with error -524
Whereas previously before commit 08412e72af ("mtd: spi-nor: core:
Return error code from set_4byte_addr_mode()") it worked just fine.
Fix this by ignoring -ENOTSUPP in spi_nor_init().
Fixes: 08412e72af ("mtd: spi-nor: core: Return error code from set_4byte_addr_mode()")
Cc: stable@vger.kernel.org
Reported-by: Hongyu Ning <hongyu.ning@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220923093441.3178-1-mika.westerberg@linux.intel.com
-----BEGIN PGP SIGNATURE-----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=M+mV
-----END PGP SIGNATURE-----
Merge tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull more random number generator updates from Jason Donenfeld:
"This time with some large scale treewide cleanups.
The intent of this pull is to clean up the way callers fetch random
integers. The current rules for doing this right are:
- If you want a secure or an insecure random u64, use get_random_u64()
- If you want a secure or an insecure random u32, use get_random_u32()
The old function prandom_u32() has been deprecated for a while
now and is just a wrapper around get_random_u32(). Same for
get_random_int().
- If you want a secure or an insecure random u16, use get_random_u16()
- If you want a secure or an insecure random u8, use get_random_u8()
- If you want secure or insecure random bytes, use get_random_bytes().
The old function prandom_bytes() has been deprecated for a while
now and has long been a wrapper around get_random_bytes()
- If you want a non-uniform random u32, u16, or u8 bounded by a
certain open interval maximum, use prandom_u32_max()
I say "non-uniform", because it doesn't do any rejection sampling
or divisions. Hence, it stays within the prandom_*() namespace, not
the get_random_*() namespace.
I'm currently investigating a "uniform" function for 6.2. We'll see
what comes of that.
By applying these rules uniformly, we get several benefits:
- By using prandom_u32_max() with an upper-bound that the compiler
can prove at compile-time is ≤65536 or ≤256, internally
get_random_u16() or get_random_u8() is used, which wastes fewer
batched random bytes, and hence has higher throughput.
- By using prandom_u32_max() instead of %, when the upper-bound is
not a constant, division is still avoided, because
prandom_u32_max() uses a faster multiplication-based trick instead.
- By using get_random_u16() or get_random_u8() in cases where the
return value is intended to indeed be a u16 or a u8, we waste fewer
batched random bytes, and hence have higher throughput.
This series was originally done by hand while I was on an airplane
without Internet. Later, Kees and I worked on retroactively figuring
out what could be done with Coccinelle and what had to be done
manually, and then we split things up based on that.
So while this touches a lot of files, the actual amount of code that's
hand fiddled is comfortably small"
* tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
prandom: remove unused functions
treewide: use get_random_bytes() when possible
treewide: use get_random_u32() when possible
treewide: use get_random_{u8,u16}() when possible, part 2
treewide: use get_random_{u8,u16}() when possible, part 1
treewide: use prandom_u32_max() when possible, part 2
treewide: use prandom_u32_max() when possible, part 1
UBI:
- Use bitmap API to allocate bitmaps
- New attach mode, disable_fm, to attach without fastmap
- Fixes for various typos in comments
UBIFS:
- Fix for a deadlock when setting xattrs for encrypted file
- Fix for an assertion failures when truncating encrypted files
- Fixes for various typos in comments
-----BEGIN PGP SIGNATURE-----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=UVHq
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
"UBI:
- Use bitmap API to allocate bitmaps
- New attach mode, disable_fm, to attach without fastmap
- Fixes for various typos in comments
UBIFS:
- Fix for a deadlock when setting xattrs for encrypted file
- Fix for an assertion failures when truncating encrypted files
- Fixes for various typos in comments"
* tag 'for-linus-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: fastmap: Add fastmap control support for 'UBI_IOCATT' ioctl
ubi: fastmap: Use the bitmap API to allocate bitmaps
ubifs: Fix AA deadlock when setting xattr for encrypted file
ubifs: Fix UBIFS ro fail due to truncate in the encrypted directory
mtd: ubi: drop unexpected word 'a' in comments
ubi: block: Fix typos in comments
ubi: fastmap: Fix typo in comments
ubi: Fix repeated words in comments
ubi: ubi-media.h: Fix comment typo
ubi: block: Remove in vain semicolon
ubifs: Fix ubifs_check_dir_empty() kernel-doc comment
The prandom_bytes() function has been a deprecated inline wrapper around
get_random_bytes() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. This was done as a basic find and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> # powerpc
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Rather than truncate a 32-bit value to a 16-bit value or an 8-bit value,
simply use the get_random_{u8,u16}() functions, which are faster than
wasting the additional bytes from a 32-bit value. This was done by hand,
identifying all of the places where one of the random integer functions
was used in a non-32-bit context.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Rather than incurring a division or requesting too many random bytes for
the given range, use the prandom_u32_max() function, which only takes
the minimum required bytes from the RNG and avoids divisions. This was
done mechanically with this coccinelle script:
@basic@
expression E;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
typedef u64;
@@
(
- ((T)get_random_u32() % (E))
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ((E) - 1))
+ prandom_u32_max(E * XXX_MAKE_SURE_E_IS_POW2)
|
- ((u64)(E) * get_random_u32() >> 32)
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ~PAGE_MASK)
+ prandom_u32_max(PAGE_SIZE)
)
@multi_line@
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
identifier RAND;
expression E;
@@
- RAND = get_random_u32();
... when != RAND
- RAND %= (E);
+ RAND = prandom_u32_max(E);
// Find a potential literal
@literal_mask@
expression LITERAL;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
position p;
@@
((T)get_random_u32()@p & (LITERAL))
// Add one to the literal.
@script:python add_one@
literal << literal_mask.LITERAL;
RESULT;
@@
value = None
if literal.startswith('0x'):
value = int(literal, 16)
elif literal[0] in '123456789':
value = int(literal, 10)
if value is None:
print("I don't know how to handle %s" % (literal))
cocci.include_match(False)
elif value == 2**32 - 1 or value == 2**31 - 1 or value == 2**24 - 1 or value == 2**16 - 1 or value == 2**8 - 1:
print("Skipping 0x%x for cleanup elsewhere" % (value))
cocci.include_match(False)
elif value & (value + 1) != 0:
print("Skipping 0x%x because it's not a power of two minus one" % (value))
cocci.include_match(False)
elif literal.startswith('0x'):
coccinelle.RESULT = cocci.make_expr("0x%x" % (value + 1))
else:
coccinelle.RESULT = cocci.make_expr("%d" % (value + 1))
// Replace the literal mask with the calculated result.
@plus_one@
expression literal_mask.LITERAL;
position literal_mask.p;
expression add_one.RESULT;
identifier FUNC;
@@
- (FUNC()@p & (LITERAL))
+ prandom_u32_max(RESULT)
@collapse_ret@
type T;
identifier VAR;
expression E;
@@
{
- T VAR;
- VAR = (E);
- return VAR;
+ return E;
}
@drop_var@
type T;
identifier VAR;
@@
{
- T VAR;
... when != VAR
}
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: KP Singh <kpsingh@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4 and sbitmap
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> # for drbd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and features,
the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0GQmA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylyVQCeNJjZ3hy+Wz8WkPSY+NkehuIhyCIAnjXMOJP8
5G/JQ+rpcclr7VOXlS66
=zVkU
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and
features, the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (411 commits)
w1: Split memcpy() of struct cn_msg flexible array
spmi: pmic-arb: increase SPMI transaction timeout delay
spmi: pmic-arb: block access for invalid PMIC arbiter v5 SPMI writes
spmi: pmic-arb: correct duplicate APID to PPID mapping logic
spmi: pmic-arb: add support to dispatch interrupt based on IRQ status
spmi: pmic-arb: check apid against limits before calling irq handler
spmi: pmic-arb: do not ack and clear peripheral interrupts in cleanup_irq
spmi: pmic-arb: handle spurious interrupt
spmi: pmic-arb: add a print in cleanup_irq
drivers: spmi: Directly use ida_alloc()/free()
MAINTAINERS: add TI ECAP driver info
counter: ti-ecap-capture: capture driver support for ECAP
Documentation: ABI: sysfs-bus-counter: add frequency & num_overflows items
dt-bindings: counter: add ti,am62-ecap-capture.yaml
counter: Introduce the COUNTER_COMP_ARRAY component type
counter: Consolidate Counter extension sysfs attribute creation
counter: Introduce the Count capture component
counter: 104-quad-8: Add Signal polarity component
counter: Introduce the Signal polarity component
counter: interrupt-cnt: Implement watch_validate callback
...
* mtdchar: add MEMREAD ioctl
* Add ECC error accounting for each read request
* always initialize 'stats' in struct mtd_oob_ops
* Track maximum number of bitflips for each read request
* Fix repeated word in comment
* Move from strlcpy with unused retval to strscpy
* Fix a typo in a comment
* Add binding for U-Boot bootloader partitions
MTD device drivers changes:
* FTL: use container_of() rather than cast
* docg3:
- Use correct function names in comment blocks
- Check the return value of devm_ioremap() in the probe
* physmap-core: Fix NULL pointer dereferencing in of_select_probe_type()
* parsers: add Broadcom's U-Boot parser
Raw NAND core changes:
* Replace of_gpio_named_count() by gpiod_count()
- Remove misguided comment of nand_get_device()
- bbt: Use the bitmap API to allocate bitmaps
Raw NAND controller drivers changes:
* Meson:
- Stop supporting legacy clocks
- Refine resource getting in probe
- Convert bindings to yaml
- Fix clock handling and update the bindings accordingly
- Fix bit map use in meson_nfc_ecc_correct()
* bcm47xx:
- Fix spelling typo in comment
* STM32 FMC2:
- Switch to using devm_fwnode_gpiod_get()
- Fix dma_map_sg error check
* Cadence:
- Remove an unneeded result variable
* Marvell:
- Fix error handle regarding dma_map_sg
* Orion:
- Use devm_clk_get_optional()
* Cafe:
- Use correct function name in comment block
* Atmel:
- Unmap streaming DMA mappings
* Arasan:
- Stop using 0 as NULL pointer
* GPMI:
- Fix typo 'the the' in comment
* BRCM:
- Add individual glue driver selection
- Move Kconfig to driver folder
* FSL: Fix none ECC mode
* Intel:
- Use devm_platform_ioremap_resource_byname()
- Remove unused clk_rate member from struct ebu_nand
- Remove unused nand_pa member from ebu_nand_cs
- Don't re-define NAND_DATA_IFACE_CHECK_ONLY
- Remove undocumented compatible string
- Fix compatible string in the bindings
- Read the chip-select line from the correct OF node
- Fix maximum chip select value in the bindings
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmNAPlUACgkQJWrqGEe9
VoTQogf/VPcMpDXORmgCm0HldghXsY2WqY92xUCNDEtREUmqLe+mEVuXlucWQdeM
tthHNDhLIJQKDfmGdJiOBOqAZ5D6tjT+ZjTySOGP7TH2gzd5XmGGhFZlblioqryn
oqE2XmPs72hKaFJhcC00Y/DFeaD/EsDolyLgwl9s6hI/JGPLcRFa8Z4gjRkWW8B9
NZEk5mB1AVm2MVjXF0OkT/Pm/FtFQ1HpprV4qhG2ZOHcL1GeDrGddNCZIf3vXgKY
PXHCdjhej+zusHxVsYgkH0ju3n7OYTuxctLPbmK7Gqi3QeBj1SbpZWHEjyPrerFu
jj8W8OXErxNQN49jngnbUa0ZKwuwag==
=6/gy
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"Core MTD changes:
- mtdchar: add MEMREAD ioctl
- Add ECC error accounting for each read request
- always initialize 'stats' in struct mtd_oob_ops
- Track maximum number of bitflips for each read request
- Fix repeated word in comment
- Move from strlcpy with unused retval to strscpy
- Fix a typo in a comment
- Add binding for U-Boot bootloader partitions
MTD device drivers changes:
- FTL: use container_of() rather than cast
- docg3:
- Use correct function names in comment blocks
- Check the return value of devm_ioremap() in the probe
- physmap-core: Fix NULL pointer dereferencing in
of_select_probe_type()
- parsers: add Broadcom's U-Boot parser
Raw NAND core changes:
- Replace of_gpio_named_count() by gpiod_count()
- Remove misguided comment of nand_get_device()
- bbt: Use the bitmap API to allocate bitmaps
Raw NAND controller drivers changes:
- Meson:
- Stop supporting legacy clocks
- Refine resource getting in probe
- Convert bindings to yaml
- Fix clock handling and update the bindings accordingly
- Fix bit map use in meson_nfc_ecc_correct()
- bcm47xx:
- Fix spelling typo in comment
- STM32 FMC2:
- Switch to using devm_fwnode_gpiod_get()
- Fix dma_map_sg error check
- Cadence:
- Remove an unneeded result variable
- Marvell:
- Fix error handle regarding dma_map_sg
- Orion:
- Use devm_clk_get_optional()
- Cafe:
- Use correct function name in comment block
- Atmel:
- Unmap streaming DMA mappings
- Arasan:
- Stop using 0 as NULL pointer
- GPMI:
- Fix typo 'the the' in comment
- BRCM:
- Add individual glue driver selection
- Move Kconfig to driver folder
- FSL: Fix none ECC mode
- Intel:
- Use devm_platform_ioremap_resource_byname()
- Remove unused clk_rate member from struct ebu_nand
- Remove unused nand_pa member from ebu_nand_cs
- Don't re-define NAND_DATA_IFACE_CHECK_ONLY
- Remove undocumented compatible string
- Fix compatible string in the bindings
- Read the chip-select line from the correct OF node
- Fix maximum chip select value in the bindings"
* tag 'mtd/for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (43 commits)
mtd: rawnand: meson: stop supporting legacy clocks
dt-bindings: nand: meson: convert txt to yaml
mtd: rawnand: meson: refine resource getting in probe
mtd: rawnand: meson: fix the clock
dt-bindings: nand: meson: fix meson nfc clock
mtd: rawnand: bcm47xx: fix spelling typo in comment
mtd: rawnand: stm32_fmc2: switch to using devm_fwnode_gpiod_get()
mtd: rawnand: cadence: Remove an unneeded result variable
mtd: rawnand: Replace of_gpio_named_count() by gpiod_count()
mtd: rawnand: marvell: Fix error handle regarding dma_map_sg
mtd: rawnand: stm32_fmc2: Fix dma_map_sg error check
mtd: rawnand: remove misguided comment of nand_get_device()
mtd: rawnand: orion: Use devm_clk_get_optional()
mtd: rawnand: cafe: Use correct function name in comment block
mtd: rawnand: atmel: Unmap streaming DMA mappings
mtd: rawnand: meson: fix bit map use in meson_nfc_ecc_correct()
mtd: rawnand: arasan: stop using 0 as NULL pointer
mtd: rawnand: gpmi: Fix typo 'the the' in comment
mtd: rawnand: brcmnand: Add individual glue driver selection
mtd: rawnand: brcmnand: Move Kconfig to driver folder
...
* Replace of_gpio_named_count() by gpiod_count()
- Remove misguided comment of nand_get_device()
- bbt: Use the bitmap API to allocate bitmaps
Raw NAND controller drivers changes:
* Meson:
- Stop supporting legacy clocks
- Refine resource getting in probe
- Convert bindings to yaml
- Fix clock handling and update the bindings accordingly
- Fix bit map use in meson_nfc_ecc_correct()
* bcm47xx:
- Fix spelling typo in comment
* STM32 FMC2:
- Switch to using devm_fwnode_gpiod_get()
- Fix dma_map_sg error check
* Cadence:
- Remove an unneeded result variable
* Marvell:
- Fix error handle regarding dma_map_sg
* Orion:
- Use devm_clk_get_optional()
* Cafe:
- Use correct function name in comment block
* Atmel:
- Unmap streaming DMA mappings
* Arasan:
- Stop using 0 as NULL pointer
* GPMI:
- Fix typo 'the the' in comment
* BRCM:
- Add individual glue driver selection
- Move Kconfig to driver folder
* FSL: Fix none ECC mode
* Intel:
- Use devm_platform_ioremap_resource_byname()
- Remove unused clk_rate member from struct ebu_nand
- Remove unused nand_pa member from ebu_nand_cs
- Don't re-define NAND_DATA_IFACE_CHECK_ONLY
- Remove undocumented compatible string
- Fix compatible string in the bindings
- Read the chip-select line from the correct OF node
- Fix maximum chip select value in the bindings
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmNAOvwACgkQJWrqGEe9
VoRNwQf9EqZu7zW/kWBi7cN9koCk/5YuKeCQi9KJhCf4MC9928BdEy5wwRYPkZPJ
N1rTS4Fdx+nLDpULqcE9KYDSJZM09dGEHN7sFYwJR+zKRpBV5awfDvV8gWZp1Afk
MLtC+AWO1GkJ/5V0Qmw0RX+0rtM9v+QpH25+nvJImBKt7iTfperpBDmO7S7htxhN
xPKLj8A8Ns2LR/JirwHT2DRLwe/1UJwLxNfL/yzyWxekaqmRUNz2rYSQ56ZJAbc4
D9jotFRwdpaMIKkGuruYed2gM7rgbtzSaGLZNYuHzcLMKFocH9vLL7D3EAbovoDL
D1l1saZDYsYpXkVwM4uKPWR/B8lgcg==
=DvSB
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.1' into mtd/next
Raw NAND core changes:
* Replace of_gpio_named_count() by gpiod_count()
- Remove misguided comment of nand_get_device()
- bbt: Use the bitmap API to allocate bitmaps
Raw NAND controller drivers changes:
* Meson:
- Stop supporting legacy clocks
- Refine resource getting in probe
- Convert bindings to yaml
- Fix clock handling and update the bindings accordingly
- Fix bit map use in meson_nfc_ecc_correct()
* bcm47xx:
- Fix spelling typo in comment
* STM32 FMC2:
- Switch to using devm_fwnode_gpiod_get()
- Fix dma_map_sg error check
* Cadence:
- Remove an unneeded result variable
* Marvell:
- Fix error handle regarding dma_map_sg
* Orion:
- Use devm_clk_get_optional()
* Cafe:
- Use correct function name in comment block
* Atmel:
- Unmap streaming DMA mappings
* Arasan:
- Stop using 0 as NULL pointer
* GPMI:
- Fix typo 'the the' in comment
* BRCM:
- Add individual glue driver selection
- Move Kconfig to driver folder
* FSL: Fix none ECC mode
* Intel:
- Use devm_platform_ioremap_resource_byname()
- Remove unused clk_rate member from struct ebu_nand
- Remove unused nand_pa member from ebu_nand_cs
- Don't re-define NAND_DATA_IFACE_CHECK_ONLY
- Remove undocumented compatible string
- Fix compatible string in the bindings
- Read the chip-select line from the correct OF node
- Fix maximum chip select value in the bindings
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The drivers branch for 6.1 is a bit larger than for most releases. Most
of the changes come from SoC maintainers for the drivers/soc subsystem:
- A new driver for error handling on the NVIDIA Tegra
'control backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip
SoCs, various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM
driver, the Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas,
Tegra, Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers that
merge updates this way:
- Various updates and new drivers in the memory controller
subsystem for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A
v1.1 specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem
-----BEGIN PGP SIGNATURE-----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=WX9J
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"The drivers branch for 6.1 is a bit larger than for most releases.
Most of the changes come from SoC maintainers for the drivers/soc
subsystem:
- A new driver for error handling on the NVIDIA Tegra 'control
backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip SoCs,
various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM driver, the
Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas, Tegra,
Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers
that merge updates this way:
- Various updates and new drivers in the memory controller subsystem
for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A v1.1
specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem"
* tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (149 commits)
ARM: remove check for CONFIG_DEBUG_LL_SER3
firmware/psci: Add debugfs support to ease debugging
firmware/psci: Print a warning if PSCI doesn't accept PC mode
dt-bindings: memory: snps,dw-umctl2-ddrc: Extend schema with IRQs/resets/clocks props
dt-bindings: memory: snps,dw-umctl2-ddrc: Replace opencoded numbers with macros
dt-bindings: memory: snps,dw-umctl2-ddrc: Use more descriptive device name
dt-bindings: memory: synopsys,ddrc-ecc: Detach Zynq DDRC controller support
soc: sunxi: sram: Add support for the D1 system control
soc: sunxi: sram: Export the LDO control register
soc: sunxi: sram: Save a pointer to the OF match data
soc: sunxi: sram: Return void from the release function
soc: apple: rtkit: Add apple_rtkit_poll
soc: imx: add i.MX93 media blk ctrl driver
soc: imx: add i.MX93 SRC power domain driver
soc: imx: imx8m-blk-ctrl: Use genpd_xlate_onecell
soc: imx: imx8mp-blk-ctrl: handle PCIe PHY resets
soc: imx: imx8m-blk-ctrl: add i.MX8MP VPU blk ctrl
soc: imx: add i.MX8MP HDMI blk ctrl HDCP/HRV_MWR
soc: imx: add icc paths for i.MX8MP hsio/hdmi blk ctrl
soc: imx: add icc paths for i.MX8MP media blk ctrl
...
MTD subsystem API allows interacting with MTD devices (e.g. reading,
writing, handling bad blocks). So far a random driver could get MTD
device only by its name (get_mtd_device_nm()). This change allows
getting them also by a DT node.
This API is required for drivers handling DT defined MTD partitions in a
specific way (e.g. U-Boot (sub)partition with environment variables).
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220916122100.170016-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[1] suggests that fastmap is suitable for large flash devices. Module
parameter 'fm_autoconvert' is a coarse grained switch to enable all
ubi devices to generate fastmap, which may turn on fastmap even for
small flash devices.
This patch imports a new field 'disable_fm' in struct 'ubi_attach_req'
to support following situations by ioctl 'UBI_IOCATT'.
[old functions]
A. Disable 'fm_autoconvert': Disbable fastmap for all ubi devices
B. Enable 'fm_autoconvert': Enable fastmap for all ubi devices
[new function]
C. Enable 'fm_autoconvert', set 'disable_fm' for given device: Don't
create new fastmap and do full scan (existed fastmap will be
destroyed) for the given ubi device.
A simple test case in [2].
[1] http://www.linux-mtd.infradead.org/doc/ubi.html#L_fastmap
[2] https://bugzilla.kernel.org/show_bug.cgi?id=216278
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Use bitmap_zalloc()/bitmap_free() instead of hand-writing them.
It is less verbose and it improves the semantic.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
there is an unexpected word 'a' in the comments that need to be dropped
file - drivers/mtd/ubi/vmt.c
line - 626,779
* Returns zero if volume is all right and a a negative error code if not.
changed to:
* Returns zero if volume is all right and a negative error code if not.
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Richard Weinberger <richard@nod.at>
There are a typo(dont't) in comments.
Fix it.
Signed-off-by: Zhang Jiaming <jiaming@nfschina.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Delete the redundant word 'a'.
Delete the redundant word 'the'.
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The double `the' is duplicated in the comment, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Remove the repeated ';' from code, it is not
needed.
Signed-off-by: Li zeming <zeming@nfschina.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
[rw: Massaged commit message a bit]
Signed-off-by: Richard Weinberger <richard@nod.at>
meson NFC driver only uses common clock interfaces, which triggers kernel test
robot errors when using legacy clocks with HAVE_LEGACY_CLK on.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
[miquel.raynal@bootlin.com: Rephrase the commit log]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220907080405.28240-6-liang.yang@amlogic.com
simply use devm_platform_ioremap_resource_byname() instead of two steps:
res = platform_get_resource(pdev, IORESOURCE_MEM, 0) and
reg_base = devm_ioremap_resource(dev, res)
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220907080405.28240-4-liang.yang@amlogic.com
EMMC and NAND have the same clock control register named 'SD_EMMC_CLOCK'
which is defined in EMMC port internally. bit0~5 of 'SD_EMMC_CLOCK' is
the divider and bit6~7 is the mux for fix pll and xtal. At the beginning,
a common MMC and NAND sub-clock was discussed and planed to be implemented
as NFC clock provider, but now this series of patches of a common MMC and
NAND sub-clock are never being accepted. the reasons for giving up are:
1. EMMC and NAND, which are mutually exclusive anyway
2. coupling the EMMC and NAND.
3. it seems that a common MMC and NAND sub-clock is over engineered.
and let us see the link fot more information:
https://lore.kernel.org/all/20220121074508.42168-5-liang.yang@amlogic.com
so The meson nfc can't work now, let us rework the clock.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220907080405.28240-3-liang.yang@amlogic.com
Return the value cadence_nand_set_access_width16() directly instead of
storing it in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220901074555.313266-1-ye.xingchen@zte.com.cn
After commit 8cba323437 ("mtd: rawnand: protect access to rawnand devices
while in suspend"), it will wait while in suspend rather than returning
errors. So remove the misguided comment about return value.
Signed-off-by: ChenXiaoSong <chenxiaosong2@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220819021846.2924539-1-chenxiaosong2@huawei.com
Every dma_map_single() call should have its dma_unmap_single() counterpart,
because the DMA address space is a shared resource and one could render the
machine unusable by consuming all DMA addresses.
Link: https://lore.kernel.org/lkml/13c6c9a2-6db5-c3bf-349b-4c127ad3496a@axentia.se/
Cc: stable@vger.kernel.org
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Alexander Dahl <ada@thorsis.com>
Reported-by: Peter Rosin <peda@axentia.se>
Tested-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220728074014.145406-1-tudor.ambarus@microchip.com
The meson_nfc_ecc_correct() function accidentally does a right shift
instead of a left shift so it only works for BIT(0). Also use
BIT_ULL() because "correct_bitmap" is a u64 and we want to avoid
shift wrapping bugs.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YuI2zF1hP65+LE7r@kili
Allow each platform to define a dedicated Kconfig entry for its glue
driver such that we can decide on a per-platfomr basis whether to build
it or not. This allows for a finer grained control over the resulting
kernel image or set of modules.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220711222323.4048197-3-f.fainelli@gmail.com
In preparation for allowing each of the brcmnand stub to be built
separately, move the Kconfig entry to the driver folder.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220711222323.4048197-2-f.fainelli@gmail.com
User-space applications making use of MTD devices via /dev/mtd*
character devices currently have limited capabilities for reading data:
- only deprecated methods of accessing OOB layout information exist,
- there is no way to explicitly specify MTD operation mode to use; it
is auto-selected based on the MTD file mode (MTD_FILE_MODE_*) set
for the character device; in particular, this prevents using
MTD_OPS_AUTO_OOB for reads,
- all existing user-space interfaces which cause mtd_read() or
mtd_read_oob() to be called (via mtdchar_read() and
mtdchar_read_oob(), respectively) return success even when those
functions return -EUCLEAN or -EBADMSG; this renders user-space
applications using these interfaces unaware of any corrected
bitflips or uncorrectable ECC errors detected during reads.
Note that the existing MEMWRITE ioctl allows the MTD operation mode to
be explicitly set, allowing user-space applications to write page data
and OOB data without requiring them to know anything about the OOB
layout of the MTD device they are writing to (MTD_OPS_AUTO_OOB). Also,
the MEMWRITE ioctl does not mangle the return value of mtd_write_oob().
Add a new ioctl, MEMREAD, which addresses the above issues. It is
intended to be a read-side counterpart of the existing MEMWRITE ioctl.
Similarly to the latter, the read operation is performed in a loop which
processes at most mtd->erasesize bytes in each iteration. This is done
to prevent unbounded memory allocations caused by calling kmalloc() with
the 'size' argument taken directly from the struct mtd_read_req provided
by user space. However, the new ioctl is implemented so that the values
it returns match those that would have been returned if just a single
mtd_read_oob() call was issued to handle the entire read operation in
one go.
Note that while just returning -EUCLEAN or -EBADMSG to user space would
already be a valid and useful indication of the ECC algorithm detecting
errors during a read operation, that signal would not be granular enough
to cover all use cases. For example, knowing the maximum number of
bitflips detected in a single ECC step during a read operation performed
on a given page may be useful when dealing with an MTD partition whose
ECC layout varies across pages (e.g. a partition consisting of a
bootloader area using a "custom" ECC layout followed by data pages using
a "standard" ECC layout). To address that, include ECC statistics in
the structure returned to user space by the new MEMREAD ioctl.
Link: https://www.infradead.org/pipermail/linux-mtd/2016-April/067085.html
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220629125737.14418-5-kernel@kempniu.pl
Extend struct mtd_req_stats with two new fields holding the number of
corrected bitflips and uncorrectable errors detected during a read
operation. This is a prerequisite for ultimately passing those counters
to user space, where they can be useful to applications for making
better-informed choices about moving data around.
Unlike 'max_bitflips' (which is set - in a common code path - to the
return value of a function called while the MTD device's mutex is held),
these counters have to be maintained in each MTD driver which defines
the '_read_oob' callback because the statistics need to be calculated
while the MTD device's mutex is held.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220629125737.14418-4-kernel@kempniu.pl
As the 'stats' field in struct mtd_oob_ops is used in conditional
expressions, ensure it is always zero-initialized in all such structures
to prevent random stack garbage from being interpreted as a pointer.
Strictly speaking, this problem currently only needs to be fixed for
struct mtd_oob_ops structures subsequently passed to mtd_read_oob().
However, this commit goes a step further and makes all instances of
struct mtd_oob_ops in the tree zero-initialized, in hope of preventing
future problems, e.g. if struct mtd_req_stats gets extended with write
statistics at some point.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220629125737.14418-3-kernel@kempniu.pl
mtd_read_oob() callers are currently oblivious to the details of ECC
errors detected during the read operation - they only learn (through the
return value) whether any corrected bitflips or uncorrectable errors
occurred. More detailed ECC information can be useful to user-space
applications for making better-informed choices about moving data
around.
Extend struct mtd_oob_ops with a pointer to a newly-introduced struct
mtd_req_stats and set its 'max_bitflips' field to the maximum number of
bitflips found in a single ECC step during the read operation performed
by mtd_read_oob(). This is a prerequisite for ultimately passing that
value back to user space.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220629125737.14418-2-kernel@kempniu.pl
Commit f6424c22aa ("mtd: rawnand: fsl_elbc: Make SW ECC work") added
support for specifying ECC mode via DTS and skipping autodetection.
But it broke explicit specification of HW ECC mode in DTS as correct
settings for HW ECC mode are applied only when NONE mode or nothing was
specified in DTS file.
Also it started aliasing NONE mode to be same as when ECC mode was not
specified and disallowed usage of ON_DIE mode.
Fix all these issues. Use autodetection of ECC mode only in case when mode
was really not specified in DTS file by checking that ecc value is invalid.
Set HW ECC settings either when HW ECC was specified in DTS or it was
autodetected. And do not fail when ON_DIE mode is set.
Fixes: f6424c22aa ("mtd: rawnand: fsl_elbc: Make SW ECC work")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220707184328.3845-1-pali@kernel.org
Switch from open-coded platform_get_resource_byname() and
devm_ioremap_resource() to devm_platform_ioremap_resource_byname() where
possible to simplify the code.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220702231227.1579176-9-martin.blumenstingl@googlemail.com
NAND_DATA_IFACE_CHECK_ONLY is already defined in
include/linux/mtd/rawnand.h which is also included by the driver. Drop
the re-definition from the intel-nand-controller driver.
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220702231227.1579176-6-martin.blumenstingl@googlemail.com
The "intel,nand-controller" compatible string is not part of the
dt-bindings. Remove it from the driver as it's not supposed to be used
without any documentation for it.
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220702231227.1579176-5-martin.blumenstingl@googlemail.com
The incorrect function name is being used in the comment for functions
doc_set_reliable_mode, doc_read_seek and docg3_probe. Correct these
comments.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220805175423.2374939-1-colin.i.king@gmail.com
The function devm_ioremap() in docg3_probe() can fail, so
its return value should be checked.
Fixes: 82402aeb8c ("mtd: docg3: Use devm_*() functions")
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: William Dean <williamsukatube@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220722091644.2937953-1-williamsukatube@163.com
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With Broadcom Broadband arch ARCH_BCMBCA supported in the kernel, this
patch series migrate the ARCH_BCM4908 symbol to ARCH_BCMBCA. Hence
replace ARCH_BCM4908 with ARCH_BCMBCA in subsystem Kconfig files.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> (for watchdog)
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (for drivers/pci)
Acked-by: Wolfram Sang <wsa@kernel.org> (for i2c)
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> (for reset)
Link: https://lore.kernel.org/r/20220803175455.47638-7-william.zhang@broadcom.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* Dynamic partition support
* Fix deadlock in sm_ftl
* Various refcount fixes in maps, partitions and parser code
* Integer overflow fixes in mtdchar
* Support for Sercomm partitions
NAND driver changes:
* Clockrate fix for arasan
* Add ATO25D1GA support
* Double free fix for meson driver
* Fix probe/remove methods in cafe NAND
* Support unprotected spare data pages in qcom_nandc
SPI NOR core changes:
* move SECT_4K_PMC flag out of the core as it's a vendor specific flag
* s/addr_width/addr_nbytes: address width means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes.
* do not change nor->addr_nbytes at SFDP parsing time. At the SFDP parsing
time we should not change members of struct spi_nor, but instead fill
members of struct spi_nor_flash_parameters which could later on be used
by the callers.
* track flash's internal address mode so that we can use 4B opcodes
together with opcodes that don't have a 4B opcode correspondent.
SPI NOR manufacturer drivers changes:
* esmt: Rename "f25l32qa" flash name to "f25l32qa-2s".
* micron-st: Skip FSR reading if SPI controller does not support it to
allow flashes that support FSR to work even when attached to such SPI
controllers.
* spansion: Add s25hl-t/s25hs-t IDs and fixups.
-----BEGIN PGP SIGNATURE-----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=eBd9
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- Dynamic partition support
- Fix deadlock in sm_ftl
- Various refcount fixes in maps, partitions and parser code
- Integer overflow fixes in mtdchar
- Support for Sercomm partitions
NAND driver changes:
- Clockrate fix for arasan
- Add ATO25D1GA support
- Double free fix for meson driver
- Fix probe/remove methods in cafe NAND
- Support unprotected spare data pages in qcom_nandc
SPI NOR core changes:
- move SECT_4K_PMC flag out of the core as it's a vendor specific
flag
- s/addr_width/addr_nbytes/g: address width means the number of IO
lines used for the address, whereas in the code it is used as the
number of address bytes.
- do not change nor->addr_nbytes at SFDP parsing time. At the SFDP
parsing time we should not change members of struct spi_nor, but
instead fill members of struct spi_nor_flash_parameters which could
later on be used by the callers.
- track flash's internal address mode so that we can use 4B opcodes
together with opcodes that don't have a 4B opcode correspondent.
SPI NOR manufacturer drivers changes:
- esmt: Rename "f25l32qa" flash name to "f25l32qa-2s".
- micron-st: Skip FSR reading if SPI controller does not support it
to allow flashes that support FSR to work even when attached to
such SPI controllers.
- spansion: Add s25hl-t/s25hs-t IDs and fixups"
* tag 'mtd/for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (53 commits)
mtd: core: check partition before dereference
mtd: spi-nor: fix spi_nor_spimem_setup_op() call in spi_nor_erase_{sector,chip}()
mtd: spi-nor: spansion: Add s25hl-t/s25hs-t IDs and fixups
mtd: spi-nor: spansion: Add local function to discover page size
mtd: spi-nor: core: Track flash's internal address mode
mtd: spi-nor: core: Return error code from set_4byte_addr_mode()
mtd: spi-nor: Do not change nor->addr_nbytes at SFDP parsing time
mtd: spi-nor: core: Shrink the storage size of the flash_info's addr_nbytes
mtd: spi-nor: s/addr_width/addr_nbytes
mtd: spi-nor: esmt: Use correct name of f25l32qa
mtd: spi-nor: micron-st: Skip FSR reading if SPI controller does not support it
MAINTAINERS: Use my kernel.org email
mtd: rawnand: arasan: Fix clock rate in NV-DDR
mtd: rawnand: arasan: Update NAND bus clock instead of system clock
mtd: core: introduce of support for dynamic partitions
dt-bindings: mtd: partitions: add additional example for qcom,smem-part
dt-bindings: mtd: partitions: support label/name only partition
mtd: spi-nor: move SECT_4K_PMC special handling
mtd: dataflash: Add SPI ID table
mtd: hyperbus: rpc-if: Fix RPM imbalance in probe error path
...
-----BEGIN PGP SIGNATURE-----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=celk
-----END PGP SIGNATURE-----
Merge tag 'for-5.20/block-2022-07-29' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Improve the type checking of request flags (Bart)
- Ensure queue mapping for a single queues always picks the right queue
(Bart)
- Sanitize the io priority handling (Jan)
- rq-qos race fix (Jinke)
- Reserved tags handling improvements (John)
- Separate memory alignment from file/disk offset aligment for O_DIRECT
(Keith)
- Add new ublk driver, userspace block driver using io_uring for
communication with the userspace backend (Ming)
- Use try_cmpxchg() to cleanup the code in various spots (Uros)
- Finally remove bdevname() (Christoph)
- Clean up the zoned device handling (Christoph)
- Clean up independent access range support (Christoph)
- Clean up and improve block sysfs handling (Christoph)
- Clean up and improve teardown of block devices.
This turns the usual two step process into something that is simpler
to implement and handle in block drivers (Christoph)
- Clean up chunk size handling (Christoph)
- Misc cleanups and fixes (Bart, Bo, Dan, GuoYong, Jason, Keith, Liu,
Ming, Sebastian, Yang, Ying)
* tag 'for-5.20/block-2022-07-29' of git://git.kernel.dk/linux-block: (178 commits)
ublk_drv: fix double shift bug
ublk_drv: make sure that correct flags(features) returned to userspace
ublk_drv: fix error handling of ublk_add_dev
ublk_drv: fix lockdep warning
block: remove __blk_get_queue
block: call blk_mq_exit_queue from disk_release for never added disks
blk-mq: fix error handling in __blk_mq_alloc_disk
ublk: defer disk allocation
ublk: rewrite ublk_ctrl_get_queue_affinity to not rely on hctx->cpumask
ublk: fold __ublk_create_dev into ublk_ctrl_add_dev
ublk: cleanup ublk_ctrl_uring_cmd
ublk: simplify ublk_ch_open and ublk_ch_release
ublk: remove the empty open and release block device operations
ublk: remove UBLK_IO_F_PREFLUSH
ublk: add a MAINTAINERS entry
block: don't allow the same type rq_qos add more than once
mmc: fix disk/queue leak in case of adding disk failure
ublk_drv: fix an IS_ERR() vs NULL check
ublk: remove UBLK_IO_F_INTEGRITY
ublk_drv: remove unneeded semicolon
...
syzbot is reporting NULL pointer dereference at mtd_check_of_node() [1],
for mtdram test device (CONFIG_MTD_MTDRAM) is not partition.
Link: https://syzkaller.appspot.com/bug?extid=fe013f55a2814a9e8cfd [1]
Reported-by: syzbot <syzbot+fe013f55a2814a9e8cfd@syzkaller.appspotmail.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: ad9b10d1ea ("mtd: core: introduce of support for dynamic partitions")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
CC: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
- move SECT_4K_PMC flag out of the core as it's a vendor specific flag
- s/addr_width/addr_nbytes: address width means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes.
- do not change nor->addr_nbytes at SFDP parsing time. At the SFDP parsing
time we should not change members of struct spi_nor, but instead fill
members of struct spi_nor_flash_parameters which could later on be used
by the callers.
- track flash's internal address mode so that we can use 4B opcodes
together with opcodes that don't have a 4B opcode correspondent.
SPI NOR manufacturer drivers changes:
- esmt: Rename "f25l32qa" flash name to "f25l32qa-2s".
- micron-st: Skip FSR reading if SPI controller does not support it to
allow flashes that support FSR to work even when attached to such SPI
controllers.
- spansion: Add s25hl-t/s25hs-t IDs and fixups.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmLjfRkACgkQS1VPR6WN
FOn9BQf/bCkxIpGY64RoV5CLNuDj+d4nAlqa7YaL7ftkHvgpEJd8x540dWxYnTsW
FzOReFnZRtb4yjFAlOmYyqYhFuhWjDV4fmjWkeZwLqNM4GN80wKF3btf4V06gp5S
Levjgmqiz/qBsrz9QYdDcB8YLVMOgInQLV8fNrBaG2oLAdskrzXaAukzkmvwnrHM
iVQFZVLfP20qJOnoeahGJ7QObx2A8E9B2APXl9lOCTiVwuDwbFhkKQ3Vf7EqeOS1
BTwSRplAia/JvV+AsESQIL7C4I/xjDbIQ/UD9XsWD7yHo7f8FNi0fxrQ+j8HSnz9
49Ho+csCSV3MMqwnzQT6ciDzzd2zag==
=MJ3w
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.20' into mtd/next
SPI NOR core changes:
- move SECT_4K_PMC flag out of the core as it's a vendor specific flag
- s/addr_width/addr_nbytes: address width means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes.
- do not change nor->addr_nbytes at SFDP parsing time. At the SFDP parsing
time we should not change members of struct spi_nor, but instead fill
members of struct spi_nor_flash_parameters which could later on be used
by the callers.
- track flash's internal address mode so that we can use 4B opcodes
together with opcodes that don't have a 4B opcode correspondent.
SPI NOR manufacturer drivers changes:
- esmt: Rename "f25l32qa" flash name to "f25l32qa-2s".
- micron-st: Skip FSR reading if SPI controller does not support it to
allow flashes that support FSR to work even when attached to such SPI
controllers.
- spansion: Add s25hl-t/s25hs-t IDs and fixups.
For erase operations, reg_proto must be used as indicated in
struct spi_nor description in spi-nor.h.
This issue was found when DT property spi-tx-bus-width is set to 4.
In this case the spi_mem_op->addr.buswidth is set to 4 for erase command
which is not correct.
Tested on stm32mp157c-ev1 board with mx66l51235f spi-nor.
Fixes: 0e30f47232 ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
[ta: use nor->reg_proto in spi_nor_controller_ops_erase()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220629133013.3382393-1-patrice.chotard@foss.st.com
The S25HL-T/S25HS-T family is the Infineon SEMPER Flash with Quad SPI.
These Infineon chips support volatile version of configuration registers
and it is recommended to update volatile registers in the field application
due to a risk of the non-volatile registers corruption by power interrupt.
Add support for volatile QE bit.
For the single-die package parts (512Mb and 1Gb), only bottom 4KB and
uniform sector sizes are supported. This is due to missing or incorrect
entries in SMPT. Fixup for other sector sizes configurations will be
followed up as needed.
Tested on Xilinx Zynq-7000 FPGA board.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-8-tudor.ambarus@microchip.com
The page size check in s28hs512t fixup can be used for s25hs/hl-t as well.
Move that to a newly created local function.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-7-tudor.ambarus@microchip.com
We need to track the flash's internal address mode as there are flashes
that can operate with 4B opcodes but unfortunately do not have a 4B opcode
correspondent for all the 3B opcodes. Such an example is the Infineon
Semper chips which provide 4B opcodes for read/program/erase but do not
provide 4B opcodes for Read/Write Any Register. These registers are
indexed by address and require the internal address mode of the flash
before Read/Write Any Register opcodes are issued.
4B opcodes are preferred over changing the flash's address mode to 4byte,
as set_4byte_addr_mode could be done in a non-volatile way and could break
the boot sequence. Thus we need to track the flash's internal address mode
so that we can use 4B opcodes together with opcodes that don't have a 4B
opcode correspondent. Track flash's internal address mode.
addr_mode_nbytes is discovered when parsing BFPT. For the
BFPT_DWORD1_ADDRESS_BYTES_3_OR_4 case, one could introduce a method that
queries the flash's internal address mode at run-time (works for Winbond).
If a run-time querying can not be accomplished or if SFDP is not defined
at all, but the address mode is volatile and resets to a default known
value at boot, one can change the default addr_mode_nbytes value of 3 by
introducing a flash_info flag. If the address mode can not be queried,
discovered and it is configured via a non-volatile register, we may
introduce a dt property, but it will harm the generic approach of the
jedec,spi-nor compatible. All this complexity is not needed now, so let it
for future development.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-6-tudor.ambarus@microchip.com
The prams->set_4byte_addr_mode returns error code but is not handled
in spi_nor_init(). Handle the return code from set_4byte_addr_mode().
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-5-tudor.ambarus@microchip.com
At the SFDP parsing time we should not change members of struct spi_nor,
but instead fill members of struct spi_nor_flash_parameters which could
later on be used by callers. The caller will then decide if SFDP params
should be used and more importantly when they should be used. Clean the
code flow and don't initialize nor->addr_nbytes at SFDP parsing time.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-4-tudor.ambarus@microchip.com
The maximum number of address bytes in SPI NOR is 4. Shrink the storage
size of the flash_info's addr_nbytes.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-3-tudor.ambarus@microchip.com
Address width was an unfortunate name, as it means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes. s/addr_width/addr_nbytes throughout the entire SPI NOR
framework.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-2-tudor.ambarus@microchip.com
The Intel SPI controller does not support low level operations, like
reading the flag status register (FSR). It only exposes a set of high
level operations for software to use. For this reason check the return
value of micron_st_nor_read_fsr() and if the operation was not
supported, use the status register value only. This allows the chip to
work even when attached to Intel SPI controller (there are such systems
out there).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220506105158.43613-1-mika.westerberg@linux.intel.com
06781a5026 Fixes the calculation of the DEVICE_BUSY_TIMEOUT register
value from busy_timeout_cycles. busy_timeout_cycles is calculated wrong
though: It is calculated based on the maximum page read time, but the
timeout is also used for page write and block erase operations which
require orders of magnitude bigger timeouts.
Fix this by calculating busy_timeout_cycles from the maximum of
tBERS_max and tPROG_max.
This is for now the easiest and most obvious way to fix the driver.
There's room for improvements though: The NAND_OP_WAITRDY_INSTR tells us
the desired timeout for the current operation, so we could program the
timeout dynamically for each operation instead of setting a fixed
timeout. Also we could wire up the interrupt handler to actually detect
and forward timeouts occurred when waiting for the chip being ready.
As a sidenote I verified that the change in 06781a5026 is really
correct. I wired up the interrupt handler in my tree and measured the
time between starting the operation and the timeout interrupt handler
coming in. The time increases 41us with each step in the timeout
register which corresponds to 4096 clock cycles with the 99MHz clock
that I have.
Fixes: 06781a5026 ("mtd: rawnand: gpmi: Fix setting busy timeout setting")
Fixes: b120612206 ("mtd: rawniand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
According to the Arasan NAND controller spec, the flash clock rate for SDR
must be <= 100 MHz, while for NV-DDR it must be the same as the rate of the
CLK line for the mode. The driver previously always set 100 MHz for NV-DDR,
which would result in incorrect behavior for NV-DDR modes 0-4.
The appropriate clock rate can be calculated from the NV-DDR timing
parameters as 1/tCK, or for rates measured in picoseconds,
10^12 / nand_nvddr_timings->tCK_min.
Fixes: 197b88fecc ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable@vger.kernel.org # 5.8+
Signed-off-by: Olga Kitaina <okitain@gmail.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220628154824.12222-3-amit.kumar-mahapatra@xilinx.com
In current implementation the Arasan NAND driver is updating the
system clock(i.e., anand->clk) in accordance to the timing modes
(i.e., SDR or NVDDR). But as per the Arasan NAND controller spec the
flash clock or the NAND bus clock(i.e., nfc->bus_clk), need to be
updated instead. This patch keeps the system clock unchanged and updates
the NAND bus clock as per the timing modes.
Fixes: 197b88fecc ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable@vger.kernel.org # 5.8+
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220628154824.12222-2-amit.kumar-mahapatra@xilinx.com
We have many parser that register mtd partitions at runtime. One example
is the cmdlinepart or the smem-part parser where the compatible is defined
in the dts and the partitions gets detected and registered by the
parser. This is problematic for the NVMEM subsystem that requires an OF
node to detect NVMEM cells.
To fix this problem, introduce an additional logic that will try to
assign an OF node to the MTD if declared.
On MTD addition, it will be checked if the MTD has an OF node and if
not declared will check if a partition with the same label / node name is
declared in DTS. If an exact match is found, the partition dynamically
allocated by the parser will have a connected OF node.
The NVMEM subsystem will detect the OF node and register any NVMEM cells
declared statically in the DTS.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220622010628.30414-4-ansuelsmth@gmail.com
blk_cleanup_disk is nothing but a trivial wrapper for put_disk now,
so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20220619060552.1850436-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The SECT_4K_PMC flag will set a device specific opcode for the 4k sector
erase. Instead of handling it in the core, we can move it to a
late_init(). In that late init, loop over all erase types, look for the
4k size and replace the opcode.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220418112650.2791459-1-michael@walle.cc
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220620152313.708768-1-broonie@kernel.org
there is an unexpected word 'is' in the comments that need to be dropped
file: drivers/mtd/nand/raw/sm_common.c
line: 55
/* NOTE: This layout is is not compatabable with SmartMedia, */
changed to:
/* NOTE: This layout is not compatabable with SmartMedia, */
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220622160511.11679-1-jiangjian@cdjrlc.com
IPQ8064 nand have special pages where a different layout scheme is used.
These special page are used by boot partition and on reading them
lots of warning are reported about wrong ECC data and if written to
results in broken data and not bootable device.
The layout scheme used by these special page consist in using 512 bytes
as the codeword size (even for the last codeword) while writing to CFG0
register. This forces the NAND controller to unprotect the 4 bytes of
spare data.
Since the kernel is unaware of this different layout for these special
page, it does try to protect the spare data too during read/write and
warn about CRC errors.
Add support for this by permitting the user to declare these special
pages in dts by declaring offset and size of the partition. The driver
internally will convert these value to nand pages.
On user read/write the page is checked and if it's a boot page the
correct layout is used.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220616001835.24393-3-ansuelsmth@gmail.com
of_get_child_by_name() will increase the refcount of 'ofpart_node',
so add of_node_put() after using it to avoid refcount leak.
Fixes: 9b78ef0c79 ("mtd: parsers: add support for Sercomm partitions")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220617014008.851583-1-yangyingliang@huawei.com
The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as:
| Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY
| mode. This value is the number of GPMI_CLK cycles multiplied by 4096.
So instead of multiplying the value in cycles with 4096, we have to
divide it by that value. Use DIV_ROUND_UP to make sure we are on the
safe side, especially when the calculated value in cycles is smaller
than 4096 as typically the case.
This bug likely never triggered because any timeout != 0 usually will
do. In my case the busy timeout in cycles was originally calculated as
2408, which multiplied with 4096 is 0x968000. The lower 16 bits were
taken for the 16 bit wide register field, so the register value was
0x8000. With 2970bf5a32 ("mtd: rawnand: gpmi: fix controller timings
setting") however the value in cycles became 2384, which multiplied
with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an
intermediate timeout when reading from NAND.
Fixes: b120612206 ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220614083138.3455683-1-s.hauer@pengutronix.de
This reverts commit 3380557fc7.
It turned out this "4-byte" ID might have been an honest mistake.
Regrettably, the chip Andreas has might be a counterfeit or is
damaged in some other way and shouldn't have ended up in a router.
Andreas reported his chip is returning just four bytes:
"98 f1 80 15 00 00 00 00".
However, according to Kioxia/Toshiba's datasheet, there should
have been at least another byte that would have contained the
correct OOB size that Andreas needed.
Miquel and Andreas are both favoring reverting the patch over
further, possibly hacky modifications:
"[Reverting] is the safest option here. Apart from this device, we
do not know how many devices have these damaged/counterfeit chips.
If it is just a couple and only on Fritzboxes, as suggested in the
Github issue the patch could be carried through OpenWrt[...]"
Thanks to several users on the openwrt forum and github issue,
who stayed along for the ride:
- Peter-vdL for reporting the issue and testing patches.
- neg2led and Hannu Nyman who did all the
datasheet digging and debugging.
Cc: Andreas Boehler <dev@aboehler.at>
Suggested-by: Andreas Boehler <dev@aboehler.at>
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://github.com/openwrt/openwrt/issues/9962
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607185918.1048204-1-chunkeey@gmail.com
