Commit Graph

18 Commits

Author SHA1 Message Date
Maxime Ripard
7dab9adb7d
ARM: dts: sun7i: Provide default muxing for relevant controllers
The I2C and MMC controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
2018-11-28 15:14:15 +01:00
Maxime Ripard
0356f1ae06
ARM: dts: sun7i: Remove underscores from nodes names
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.

Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
2018-11-28 15:14:14 +01:00
Maxime Ripard
85a8c520ca
ARM: dts: sun7i: Change pinctrl nodes to avoid warning
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.

In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
2018-11-28 15:14:13 +01:00
Maxime Ripard
054da074b1
ARM: dts: sun7i: Remove all useless pinctrl nodes
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
2018-11-28 15:14:12 +01:00
Tuomas Tynkkynen
45e01f401a
ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-02-13 09:37:22 +01:00
Tuomas Tynkkynen
ad87b75f16 ARM: dts: sun7i: Enable HDMI on pcDuino3 Nano
The board has a regular-sized HDMI connector, so enable the display
the pipeline and HDMI output for it.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-12-15 15:46:17 +01:00
Chen-Yu Tsai
cf439662af ARM: sunxi: Drop mmc0_cd_pin_reference_design pinmux setting
As part of our effort to move pinctrl/GPIO interlocking into the
driver where it belongs, this patch drops the definition and usage
of the mmc0_cd_pin_reference_design pinmux setting for the default
mmc0 card detect GPIO pin.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-05-14 08:32:31 +02:00
Maxime Ripard
1edcd36fcb ARM: sunxi: Convert pinctrl nodes to generic bindings
Now that we can handle the generic pinctrl bindings, convert our DT to it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-26 08:27:11 +01:00
Maxime Ripard
119c366aea ARM: sunxi: Remove useless allwinner,pull property
The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).

Remove these properties to make it obvious that we do not set anything in
such a case.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-26 08:24:50 +01:00
Maxime Ripard
d312f6fb80 ARM: sunxi: Remove useless allwinner,drive property
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-26 08:24:50 +01:00
Adam Sampson
e04a61c04a ARM: sun7i: dt: Enable audio codec on pcDuino V3 Nano
The pcDuino V3 Nano has a 3.5mm TRRS jack socket for audio, using the
CTIA standard pinout, connected to HPOUTL, HPOUTR, HPCOM/HPCOMFB and
MICIN1/VMIC (via appropriate RC networks) on the A20. The PH00 GPIO is
wired for headphone plug detection: it reads 0 when nothing's plugged
in, and 1 when a plug is inserted.

LINEINL/R and FMINL/R are not connected.

Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-11-17 09:40:07 +01:00
Adam Sampson
f5bad43b53 ARM: dts: sun7i: Enable USB DRC on pcDuino v3 Nano
The OTG arrangement on the LinkSprite pcDuino v3 Nano is the same as the
pcDuino 1/2/3: the OTG port's 5V line is connected directly to the 5V
bus (it's not switchable), and the OTG port's ID pin is connected to PH4
on the A20.

Tested successfully in both host and device modes.

Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-19 20:05:24 +02:00
Adam Sampson
8a880ee6da ARM: dts: sun7i: Add regulator configuration for pcDuino v3 Nano
The power configuration on this board is the same as the pcDuino v3.
This will enable frequency/voltage scaling over the standard A20
operating points from 144 MHz to 960 MHz.

Tested using cpufreq-ljt-stress-test on two pcDuino v3 Nano boards; also
tested successfully with voltages reduced by 0.025 V.

Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-13 20:44:09 +02:00
Adam Sampson
b3f3db9c39 ARM: dts: sun7i: Correct USB regulators on pcDuino v3 Nano
The LinkSprite pcDuino v3 Nano's two USB host ports are powered by a
single RT9701GB regulator, which has its enable input tied to the A20's
PD2 pin, pulled up to 3v3 via a 10k resistor.

However, the script.bin that shipped with the device listed PH11 and PH3
as Vbus control pins for the two USB ports. Neither of these are
actually connected to anything.

Siarhei Siamashka spotted this problem while reviewing the other
LinkSprite boards. This patch fixes it by only defining a single
regulator, controlled by PD2. Testing shows that the USB ports are now
(correctly) only powered up once the USB PHY driver is loaded.

Reported-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-10-11 19:27:13 +02:00
Maxime Ripard
c0c2eb2476 ARM: sunxi: dt: Remove the FSF address
The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.

Remove it from our DT, as suggested.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-05-10 10:22:23 +02:00
Marcus Cooper
469a22e6ba ARM: sunxi: dts: split IR pins for A10 and A20
Currently none of the target boards nor the driver supports
IR TX. However this pin is used in a few instances as a GPIO.
Split the pin ctrl descriptions so that only the IR RX is
configured to be used.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-05-02 13:52:55 +02:00
Maxime Ripard
59ebbe88a6 ARM: sunxi: DT: Add stdout-path property
Add UART aliases and stdout-path property for all the Allwinner boards so that
we won't have to rely on the bootargs' console= value, while working with
legacy bootloaders.

While we're at it, also remove the mentions of earlyprintk in the bootargs,
that will remove our default bootargs entirely, and allow the kernel to boot on
a system even if DEBUG_LL is configured for another system.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27 08:20:30 +02:00
Adam Sampson
061035d456 ARM: dts: sun7i: Add dts file for pcDuino 3 Nano board
Add support for the LinkSprite pcDuino 3 Nano board. This is a low-cost
Allwinner A20 board with Arduino-style GPIO headers; it features 1G RAM,
4G NAND flash, 1 micro-SD, 2 USB sockets, 1 micro USB socket for OTG and
another for power in, HDMI, SATA, 5V power for SATA devices, gigabit
Ethernet, an IR receiver, 3.5mm audio out and a MIPI camera connector.

For more details, see: http://linux-sunxi.org/LinkSprite_pcDuino3_Nano

Changes in v3:
- rename LEDs to pcduino3-nano:green:usr[12]
- remove optional features on Arduino headers (i2c2, spi0, uart2)

Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27 08:20:16 +02:00