Previously the comment stated that VSI lists should be used when a
second VSI becomes a subscriber to the "VLAN address". VSI lists
are always used for VLAN membership, so replace "VLAN address" with
"MAC address". Also note that VLAN(s) always use VSI list rules.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_bridge_getlink returns the current bridge mode using
ndo_dflt_bridge_getlink and the mode parameter available in
first_switch->bridge_mode.
ice_bridge_setlink is invoked when the bridge mode needs to
changed. The value to be changed to is available as a netlink
message which is parsed in this function. If the mode has to
be changed, switch_flags is set appropriately (set ALLOW_LB
for VEB mode and clear it for VEPA mode) and ice_aq_update_vsi
is called. Also change the unicast switch filter rules.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors aspects of the VSI allocation, deletion and rebuild
flow. Some of the more noteworthy changes are described below.
1) On reset, all switch filters applied in the hardware are lost. In
the rebuild flow, only MAC and broadcast filters are being restored.
Instead, use a new function ice_replay_all_fltr to restore all the
filters that were previously added. To do this, remove calls to
ice_remove_vsi_fltr to prevent cleaning out the internal bookkeeping
structures that ice_replay_all_fltr uses to replay filters.
2) Introduce a new state bit __ICE_PREPARED_FOR_RESET to distinguish the
PF that requested the reset (and consequently prepared for it) from
the rest of the PFs. These other PFs will prepare for reset only
when they receive an interrupt from the firmware.
3) Use new functions ice_add_vsi and ice_free_vsi to create and destroy
VSIs respectively. These functions accept a handle to uniquely
identify a VSI. This same handle is required to rebuild the VSI post
reset. To prevent confusion, the existing ice_vsi_add was renamed to
ice_vsi_init.
4) Enhance ice_vsi_setup for the upcoming SR-IOV changes and expose a
new wrapper function ice_pf_vsi_setup to create PF VSIs. Rework the
error handling path in ice_setup_pf_sw.
5) Introduce a new function ice_vsi_release_all to release all PF VSIs.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is an adaptation of the work originally done by Grishma
Kotecha <grishma.kotecha@intel.com> that in summary refactors the
switch filtering logic in the driver. More specifically,
- Update the recipe structure to also store list of rules
- Update the existing code for recipes like MAC, VLAN, ethtype etc to
use list head that is attached to switch recipe structure
- Add a common function to search for a rule entry and add a new rule
entry. Update the code to use this new function.
- Refactor the rem_handle_vsi_list function to simplify the logic
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent versions of checkpatch have a new warning based on a documented
preference of Linus to not use bool in structures due to wasted space and
the size of bool is implementation dependent. For more information, see
the email thread at https://lkml.org/lkml/2017/11/21/384.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements multiple pieces of functionality:
1. Added ice_vsi_sync_filters, which is called through the service task
to push filter updates to the hardware.
2. Add support to enable/disable promiscuous mode on an interface.
Enabling/disabling promiscuous mode on an interface results in
addition/removal of a promisc filter rule through ice_vsi_sync_filters.
3. Implement handlers for ndo_set_mac_address, ndo_change_mtu,
ndo_poll_controller and ndo_set_rx_mode.
This patch also marks the end of the driver addition by bumping up the
driver version.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for VLANs. When a VLAN is created a switch filter
is added to direct the VLAN traffic to the corresponding VSI. When a VLAN
is deleted, the filter is deleted as well.
This patch also adds support for the following hardware offloads.
1) VLAN tag insertion/stripping
2) Receive Side Scaling (RSS)
3) Tx checksum and TCP segmentation
4) Rx checksum
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A VSI needs traffic directed towards it. This is done by programming
filter rules on the switch (embedded vSwitch) element in the hardware,
which connects the VSI to the ingress/egress port.
This patch introduces data structures and functions necessary to add
remove or update switch rules on the switch element. This is a pretty low
level function that is generic enough to add a whole range of filters.
This patch also introduces two top level functions ice_add_mac and
ice_remove mac which through a series of intermediate helper functions
eventually call ice_aq_sw_rules to add/delete simple MAC based filters.
It's worth noting that one invocation of ice_add_mac/ice_remove_mac
is capable of adding/deleting multiple MAC filters.
Also worth noting is the fact that the driver maintains a list of currently
active filters, so every filter addition/removal causes an update to this
list. This is done for a couple of reasons:
1) If two VSIs try to add the same filters, we need to detect it and do
things a little differently (i.e. use VSI lists, described below) as
the same filter can't be added more than once.
2) In the event of a hardware reset we can simply walk through this list
and restore the filters.
VSI Lists:
In a multi-VSI situation, it's possible that multiple VSIs want to add the
same filter rule. For example, two VSIs that want to receive broadcast
traffic would both add a filter for destination MAC ff:ff:ff:ff:ff:ff.
This can become cumbersome to maintain and so this is handled using a
VSI list.
A VSI list is resource that can be allocated in the hardware using the
ice_aq_alloc_free_res admin queue command. Simply put, a VSI list can
be thought of as a subscription list containing a set of VSIs to which
the packet should be forwarded, should the filter match.
For example, if VSI-0 has already added a broadcast filter, and VSI-1
wants to do the same thing, the filter creation flow will detect this,
allocate a VSI list and update the switch rule so that broadcast traffic
will now be forwarded to the VSI list which contains VSI-0 and VSI-1.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces data structures and functions to alloc/free
VSIs. The driver represents a VSI using the ice_vsi structure.
Some noteworthy points about VSI allocation:
1) A VSI is allocated in the firmware using the "add VSI" admin queue
command (implemented as ice_aq_add_vsi). The firmware returns an
identifier for the allocated VSI. The VSI context is used to program
certain aspects (loopback, queue map, etc.) of the VSI's configuration.
2) A VSI is deleted using the "free VSI" admin queue command (implemented
as ice_aq_free_vsi).
3) The driver represents a VSI using struct ice_vsi. This is allocated
and initialized as part of the ice_vsi_alloc flow, and deallocated
as part of the ice_vsi_delete flow.
4) Once the VSI is created, a netdev is allocated and associated with it.
The VSI's ring and vector related data structures are also allocated
and initialized.
5) A VSI's queues can either be contiguous or scattered. To do this, the
driver maintains a bitmap (vsi->avail_txqs) which is kept in sync with
the firmware's VSI queue allocation imap. If the VSI can't get a
contiguous queue allocation, it will fallback to scatter. This is
implemented in ice_vsi_get_qs which is called as part of the VSI setup
flow. In the release flow, the VSI's queues are released and the bitmap
is updated to reflect this by ice_vsi_put_qs.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds to the initialization flow by getting switch
configuration, scheduler configuration and device capabilities.
Switch configuration:
On boot, an L2 switch element is created in the firmware per physical
function. Each physical function is also mapped to a port, to which its
switch element is connected. In other words, this switch can be visualized
as an embedded vSwitch that can connect a physical function's virtual
station interfaces (VSIs) to the egress/ingress port. Egress/ingress
filters will be eventually created and applied on this switch element.
As part of the initialization flow, the driver gets configuration data
from this switch element and stores it.
Scheduler configuration:
The Tx scheduler is a subsystem responsible for setting and enforcing QoS.
As part of the initialization flow, the driver queries and stores the
default scheduler configuration for the given physical function.
Device capabilities:
As part of initialization, the driver has to determine what the device is
capable of (ex. max queues, VSIs, etc). This information is obtained from
the firmware and stored by the driver.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
