Commit 621b4d6 updated the bnx2x driver to a new FW version, but lacked
a commit to a header file with changes to the firmware's interface.
The missing interface change causes iscsi and fcoe to misbehave with the
updated firmware.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes Auto Power Saving configuration in ip101a_config_init
which was broken as there is no phy register write followed after
setting IP101A_APS_ON flag.
This patch also fixes the return value of ip101a_config_init.
Without this patch ip101a_config_init returns 2 which is not an error
accroding to IS_ERR and the mac driver will continue accessing 2 as
valid pointer to phy_dev resulting in memory fault.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare circumstances, a descriptor writeback flush may not work if it
arrives on a specific clock cycle as a writeback request is going out.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the adapter is closed while it is simultaneously going through a
reset, it can cause a null-pointer dereference when the two different code
paths simultaneously cleanup up the Tx/Rx resources.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix up code so that changes in DCB settings
are detected only when ixgbe_dcbnl_set_all is called.
Previously, a series of 'change' commands followed by
a call to ixgbe_dcbnl_set_all() would always be handled
as a HW change - even if the net change was zero.
This patch checks for this case of no actual change and
skips going through the HW set process.
Without this fix, the link could reset and result in
a link flap.
The core change in this patch is to check for changes
in the ixgbe_copy_dcb_cfg() routine - and return
a bitmask of detected changes. The other
places where changes were detected previously can be removed.
Signed-off-by: Eric Multanen <eric.w.multanen@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For every transmitted packet, ppp_start_xmit() will stop the netdev
queue and then, if appropriate, restart it. This causes the TX softirq
to run, entirely gratuitously.
This is "only" a waste of CPU time in the normal case, but it's actively
harmful when the PPP device is a TEQL slave — the wakeup will cause the
offending device to receive the next TX packet from the TEQL queue, when
it *should* have gone to the next slave in the list. We end up seeing
large bursts of packets on just *one* slave device, rather than using
the full available bandwidth over all slaves.
This patch fixes the problem by *not* unconditionally stopping the queue
in ppp_start_xmit(). It adds a return value from ppp_xmit_process()
which indicates whether the queue should be stopped or not.
It *doesn't* remove the call to netif_wake_queue() from
ppp_xmit_process(), because other code paths (especially from
ppp_output_wakeup()) need it there and it's messy to push it out to the
other callers to do it based on the return value. So we leave it in
place — it's a no-op in the case where the queue wasn't stopped, so it's
harmless in the TX path.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Provide device string properly for USB i2400m wimax devices, also
don't OOPS when providing firmware string. From Phil Sutter.
2) Add support for sh_eth SH7734 chips, from Nobuhiro Iwamatsu.
3) Add another device ID to USB zaurus driver, from Guan Xin.
4) Loop index start in pool vector iterator is wrong causing MAC to not
get configured in bnx2x driver, fix from Dmitry Kravkov.
5) EQL driver assumes HZ=100, fix from Eric Dumazet.
6) Now that skb_add_rx_frag() can specify the truesize increment
separately, do so in f_phonet and cdc_phonet, also from Eric
Dumazet.
7) virtio_net accidently uses net_ratelimit() not only on the kernel
warning but also the statistic bump, fix from Rick Jones.
8) ip_route_input_mc() uses fixed init_net namespace, oops, use
dev_net(dev) instead. Fix from Benjamin LaHaise.
9) dev_forward_skb() needs to clear the incoming interface index of the
SKB so that it looks like a new incoming packet, also from Benjamin
LaHaise.
10) iwlwifi mistakenly initializes a channel entry as 2GHZ instead of
5GHZ, fix from Stanislav Yakovlev.
11) Missing kmalloc() return value checks in orinoco, from Santosh
Nayak.
12) ath9k doesn't check for HT capabilities in the right way, it is
checking ht_supported instead of the ATH9K_HW_CAP_HT flag. Fix from
Sujith Manoharan.
13) Fix x86 BPF JIT emission of 16-bit immediate field of AND
instructions, from Feiran Zhuang.
14) Avoid infinite loop in GARP code when registering sysfs entries.
From David Ward.
15) rose protocol uses memcpy instead of memcmp in a device address
comparison, oops. Fix from Daniel Borkmann.
16) Fix build of lpc_eth due to dev_hw_addr_rancom() interface being
renamed to eth_hw_addr_random(). From Roland Stigge.
17) Make ipv6 RTM_GETROUTE interpret RTA_IIF attribute the same way
that ipv4 does. Fix from Shmulik Ladkani.
18) via-rhine has an inverted bit test, causing suspend/resume
regressions. Fix from Andreas Mohr.
19) RIONET assumes 4K page size, fix from Akinobu Mita.
20) Initialization of imask register in sky2 is buggy, because bits are
"or'd" into an uninitialized local variable. Fix from Lino
Sanfilippo.
21) Fix FCOE checksum offload handling, from Yi Zou.
22) Fix VLAN processing regression in e1000, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sky2: dont overwrite settings for PHY Quick link
tg3: Fix 5717 serdes powerdown problem
net: usb: cdc_eem: fix mtu
net: sh_eth: fix endian check for architecture independent
usb/rtl8150 : Remove duplicated definitions
rionet: fix page allocation order of rionet_active
via-rhine: fix wait-bit inversion.
ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
net: lpc_eth: Fix rename of dev_hw_addr_random
net/netfilter/nfnetlink_acct.c: use linux/atomic.h
rose_dev: fix memcpy-bug in rose_set_mac_address
Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
net/garp: avoid infinite loop if attribute already exists
x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
bonding: emit event when bonding changes MAC
mac80211: fix oper channel timestamp updation
ath9k: Use HW HT capabilites properly
MAINTAINERS: adding maintainer for ipw2x00
net: orinoco: add error handling for failed kmalloc().
net/wireless: ipw2x00: fix a typo in wiphy struct initilization
...
This patch corrects a bug in function sky2_open() of the Marvell Yukon 2 driver
in which the settings for PHY quick link are overwritten.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Stephen Hemminger <shemminger@vyattta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If port 0 of a 5717 serdes device powers down, it hides the phy from
port 1. This patch works around the problem by keeping port 0's phy
powered up.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make CDC EEM recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1494 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Tested with the Linux USB Ethernet gadget.
Cc: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
SuperH has the "CONFIG_CPU_LITTLE_ENDIAN" and the "__LITTLE_ENDIAN__".
But, other architecture doesn't have them. So, this patch fixes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist duplicated macro definitions in rtl8150.c, remove them.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rionet_active is allocated from the page allocator and the allocation
order is calculated on the assumption that the page size is 4KB, so it
wastes memory on more than 4K page systems.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug appeared in a384a33bb1
("via-rhine: RHINE_WAIT_FOR macro removal). It can be noticed
during suspend/resume.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: David Lv <DavidLv@viatech.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In parallel to the integration of lpc_eth.c, dev_hw_addr_random() has been
renamed to eth_hw_addr_random(). This patch fixes it also in the new driver
lpc_eth.c.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The merge done in commit b26e478f undid bug fix in commit c3e072f8
("net: fsl_pq_mdio: fix non tbi phy access"), with the result that non
TBI (e.g. MDIO) PHYs cannot be accessed.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Artem's cleanup of the MTD API continues apace.
Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others.
More work on DiskOnChip G3, new driver for DiskOnChip G4.
Clean up debug/warning printks in JFFS2 to use pr_<level>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk92K6UACgkQdwG7hYl686NrMACfWQJRWasR78MWKfkT2vWZwTFJ
X5AAoKiSYO2pfo5gWJGOAahNC1zUqMX0
=i3Vb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.
There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
When a bonding device is configured with fail_over_mac=active,
we expect to see the MAC address of the new active slave as the source MAC
address after failover. But we see that the source MAC address is the MAC
address of previous active slave.
Emit NETDEV_CHANGEADDR event when bonding changes its MAC address, in order
to let arp_netdev_event flush neighbour cache and route cache.
How to reproduce this bug ?
-----------hostB----------------
hostA ----- switch ---|-- eth0--bond0(192.168.100.2/24)|
(192.168.100.1/24 \--|-- eth1-/ |
--------------------------------
1 on hostB,
modprobe bonding mode=1 miimon=500 fail_over_mac=active downdelay=1000
num_grat_arp=1
ifconfig bond0 192.168.100.2/24 up
ifenslave bond0 eth0
ifenslave bond0 eth1
then eth0 is the active slave, and MAC of bond0 is MAC of eth0.
2 on hostA, ping 192.168.100.2
3 on hostB,
tcpdump -i bond0 -p icmp -XXX
you will see bond0 uses MAC of eth0 as source MAC in icmp reply.
4 on hostB,
ifconfig eth0 down
tcpdump -i bond0 -p icmp -XXX (just keep it running in step 3)
you will see first bond0 uses MAC of eth1 as source MAC in icmp
reply, then it will use MAC of eth0 as source MAC.
Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPC8569 Rev2.0 has the correct SNUM table as QE Reference Manual, we
must follow it.
However the Rev1.0 silicon need the old SNUM table as workaround due to
Rev1.0 silicon SNUM erratum.
So, we support both snum table, and choose the one FDT tell us.
And u-boot will fixup FDT according to SPRN_SVR.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Pull a few more things for powerpc by Benjamin Herrenschmidt:
- Anton's did some recent improvements to EPOW event reporting on
pSeries (power supply failures and such). The patches are self
contained enough and replace really nasty code so I felt it should
still go in
- I did the vio driver registration change Greg requested, I don't see
the point of leaving that til the next merge window
- The remaining EEH changes I said were still pending to get rid of the
EEH references from the generic struct device_node
- A few more iSeries removal bits
- A perf bug fix on 970
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf: Fix instruction address sampling on 970 and Power4
powerpc+sparc/vio: Modernize driver registration
powerpc: Random little legacy iSeries removal tidy ups
powerpc: Remove NO_IRQ_IGNORE
powerpc/pseries: Cut down on enthusiastic use of defines in RAS code
powerpc/pseries: Clean up ras_error_interrupt code
powerpc/pseries: Remove RTAS_POWERMGM_EVENTS
powerpc/pseries: Use rtas_get_sensor in RAS code
powerpc/pseries: Parse and handle EPOW interrupts
powerpc: Make function that parses RTAS error logs global
powerpc/eeh: Retrieve PHB from global list
powerpc/eeh: Remove eeh information from pci_dn
powerpc/eeh: Remove eeh device from OF node
The commit "ath9k: Remove aggregation flags" changed how
nodes were being initialized. Use the HW HT cap bits
to initialize/de-initialize nodes, else we would be
accessing an uninitialized entry during a suspend/resume cycle,
resulting in a panic.
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With flag 'GFP_ATOMIC', probability of allocation failure is more.
Add error handling after kmalloc() call to avoid null dereference.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Disintegrate asm/system.h for ARM.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Russell King <linux@arm.linux.org.uk>
cc: linux-arm-kernel@lists.infradead.org
While it is desirable to rate limit certain messages, it is not
desirable to rate limit the incrementing of counters associated
with those messages.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver version number to better match version of out of tree
driver that has similar functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This was pointed out to me by Xiaojun Zhang on Source Forge.
CC: Xiaojun Zhang <zhangxiaojun@sourceforge.net>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dan Carpenter noticed that ixgbevf initial default was different than
the rest. But the problem is broader than that, only one Intel driver (ixgb)
was doing it almost right.
The convention for default debug level should be consistent among
Intel drivers and follow established convention.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now skb_add_rx_frag() has a truesize parameter, we can fix cdc-phonet to
properly account truesize of each fragment : a full page.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HZ is more likely to be 1000 these days.
timer handlers are run from softirq, no need to disable bh
skb priority 1 is TC_PRIO_FILLER
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the bug that may prevent from mac to be configured,
while there is an empty slot for it.
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow in which the bnx2x driver starts after a previous driver
has been terminated in an 'unclean' manner has several bugs and
FW risks, which makes it possible for the driver to fail after
boot-from-SAN or kdump.
This patch contains a revised flow which performs a safer
initialization, solving the possible crash scenarios.
Notice this patch contains lines with over 80 characters, as it
keeps print-strings in a single line.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added Vendor/Device Id of Motorola Rokr E6 (22b8:6027) so it can be
recognized by the "zaurus" USBNet driver.
Applies to Linux 3.2.13 and 2.6.39.4.
Signed-off-by: Guan Xin <guanx.bac@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add define of SH7734 register and sh_eth_reset_hw_crc function.
V3: Rebase net/HEAD.
V2: Do not split line of #if defined.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way the USB variant of the driver uses usb_make_path in order to
provide bus-info compatible to other USB drivers (like e.g. asix.c).
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This happened on a machine with a custom hotplug script calling nameif,
probably due to slow firmware loading. At the time nameif uses ethtool
to gather interface information, i2400m->fw_name is zero and so a null
pointer dereference occurs from within i2400m_get_drvinfo().
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a regression introduced by commit "e1000: do vlan
cleanup (799d531)".
Apparently some e1000 chips (not mine) are sensitive about the order of
setting vlan filter and vlan stripping/inserting functionality. So this
patch changes the order so it's the same as before vlan cleanup.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
This makes vio_register_driver() get the module owner & name at compile
time like PCI drivers do, and adds a name pointer directly in struct
vio_driver to avoid having to explicitly initialize the embedded
struct device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Name string overrun fix in gianfar driver from Joe Perches.
2) VHOST bug fixes from Michael S. Tsirkin and Nadav Har'El
3) Fix dependencies on xt_LOG netfilter module, from Pablo Neira Ayuso.
4) Fix RCU locking in xt_CT, also from Pablo Neira Ayuso.
5) Add a parameter to skb_add_rx_frag() so we can fix the truesize
adjustments in the drivers that use it. The individual drivers
aren't fixed by this commit, but will be dealt with using follow-on
commits. From Eric Dumazet.
6) Add some device IDs to qmi_wwan driver, from Andrew Bird.
7) Fix a potential rcu_read_lock() imbalancein rt6_fill_node(). From
Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: fix a potential rcu_read_lock() imbalance in rt6_fill_node()
net: add a truesize parameter to skb_add_rx_frag()
gianfar: Fix possible overrun and simplify interrupt name field creation
USB: qmi_wwan: Add ZTE (Vodafone) K3570-Z and K3571-Z net interfaces
USB: option: Ignore ZTE (Vodafone) K3570/71 net interfaces
USB: qmi_wwan: Add ZTE (Vodafone) K3565-Z and K4505-Z net interfaces
qlcnic: Bug fix for LRO
netfilter: nf_conntrack: permanently attach timeout policy to conntrack
netfilter: xt_CT: fix assignation of the generic protocol tracker
netfilter: xt_CT: missing rcu_read_lock section in timeout assignment
netfilter: cttimeout: fix dependency with l4protocol conntrack module
netfilter: xt_LOG: use CONFIG_IP6_NF_IPTABLES instead of CONFIG_IPV6
vhost: fix release path lockdep checks
vhost: don't forget to schedule()
tools/virtio: stub out strong barriers
tools/virtio: add linux/hrtimer.h stub
tools/virtio: add linux/module.h stub
These are all specific to some driver. They are typically the platform
side of a change in the drivers directory, such as adding a new driver
or extending the interface to the platform. In cases where there is no
maintainer for the driver, or the maintainer prefers to have the
platform changes in the same branch as the driver changes, the patches
to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in fuse.c.
In rtc-sa1100.c, the global removal of IRQF_DISABLED conflicts with
the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pQ3X
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: driver specific updates" from Arnd Bergmann:
"These are all specific to some driver. They are typically the
platform side of a change in the drivers directory, such as adding a
new driver or extending the interface to the platform. In cases where
there is no maintainer for the driver, or the maintainer prefers to
have the platform changes in the same branch as the driver changes,
the patches to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in
fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED
conflicts with the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up aforementioned trivial conflicts.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
ARM: EXYNOS: Enable MDMA driver
regulator: Remove bq24022 regulator driver
rtc: sa1100: add OF support
pxa: magician/hx4700: Convert to gpio-regulator from bq24022
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
...
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/fuse.c
drivers/rtc/rtc-sa1100.c
